Set mpeg resolution to less than half?

Is there any way of setting the mpeg resolution to less than half? I ask this because I want to use the program strictly for HDV real time monitoring (not recording) and it seems like the latency is most affected by the mpeg resolution.

No, Half-Res is the only option. Is your CPU getting pegged while monitoring HDV at half-res? If not, then a lower res setting wouldn't help.
A major factor in latency with HDV is the interframe compression. There's a big random element to the extent of the latency depending on where in the GOP OnLocation starts getting frames. So if the latency is especially bad, cycling power on the camera might help. It's pure luck of the draw where you step into the GOP data stream.

Similar Messages

  • EPM 2013 Report is displayed as cut off and shows less than half the width of the report in IE 10 and IE 9.

    EPM 2013 Report is displayed as cut off and shows less than half the width of the report in IE 10 and IE 9.  This issue occurs for some users only.I tried the same url in google chrome and is working fine.
    Can you please help.
    Please find the attached screenshot.

    Hi BJ1986,
    According to your description, I think this issue is caused by the IE browser that runs the report. To trouble shoot this issue, I suggest that we can try to clear internet temporary files, cookies and others in IE browser. And also add this site
    as a trusted site in IE browser to check this issue again.
    If this issue is still existed, it can also be occurred due to the setting or third party add-ons of Internet Explorer (IE). In this scenario, you can try to run IE in compatibility mode to check the issue again. Or I suggest that you can refer to the
    steps below to troubleshoot the issue:
    Click Tools -> Internet options.
    Switch to the Security tab, click Local intranet, and then select Default level.
    Switch to the Advanced tab, and click Restore advanced settings.
    Temporarily disable third party add-ons. For detailed steps, please see the link below: 
    http://windows.microsoft.com/en-IN/internet-explorer/manage-add-ons#ie
    Hope this helps.
    Thanks,
    Katherine Xiong
    Katherine Xiong
    TechNet Community Support

  • Updated my 3gs to 5.0.1 and my battery life has gone from 1.5 days   to less than half a day with no Apps open - how can I roll this back to 5.0 until a fix comes out?

    Since updating my 3GS to 5.0.1 my iphone battery has gone, overnight, from 1.5 days + (with multiple open Apps) to less than half a day to completely discharge from 100%.
    I desperately need to roll this install back to 5.0 but there are no resources on the internet (or this site) which indicate how I would do that.
    Please help.
    J

    You cannot and should not go back to 5.0.
    A fix is coming soon

  • HT1848 On itunes, when synced to my pc, I show less than half of the music that is on my iphone 4. How do I get all the music onto my pc?

    I am about to scream if I don't figure this out or just decide to leave Apple and get a Galaxy phone. On itunes, when synced to my pc, I show less than half of the music that is on my iphone 4. How do I get all the music onto my pc? I have read many forums and tried many things, but apple/iTunes is not intuitive at least not on a PC. When I go to devices it won't let me select "transfer music". It's grayed out. Why is this and what can I do? I'd like to delete some of the music off of my iPhone but don't want it gone forever. Pleae help.

    Thanks Turingtest2,
    I appreciate your response. I have done all of the things mentioned, but still when I click on "devices", the "transfer music" option is still not selectable. I see it, but can't select it.  I am running Windows 7 on my PC.
    However, one thing I read makes me take pause. At one point I did erase my computer back to factory settings using the mirrored image. We backed up all information and put the important stuff back on, but I don't believe we did anything with iTunes, so it's a possibility that the music that is in my library now, may only be music I have purchased since then. But, (thinking out loud) that was a while ago and I am pretty sure I have purchased more music than what is in my iTunes library, since then.  Maybe I will approach it from that angle and see what happens.
    It just doesn't make any logical sense that syncing goes from computer to device. Ostensibly then, my iPhone would only have the music that is on my computer after syncing and that is not the case. I still have all my music on my phone. I can see the new music that's on my phone get added to my iTunes library when I connect, which would make one think that syncing occurs both ways. I don't know. It's maddening. Maybe I should just follow my husbands advice and go to an Android. LOL. Or maybe I will take my laptop and phone to the Apple store and make them figure it out. Ha.
    If you have any thoughts about this, let me know. Thanks again.

  • I have swapped my itunes to a new laptop instead of my poor old PC, however less than half of the albums have transferred. They were not purchased on itunes

    Please help, I am getting rid of my poor old PC and have tried moving my library to a laptop, however less than half of my music has appeared. How do I sort this easily?

    There should be an option to sync purchases from the iPod to iTunes.
    See this -> Copying iTunes Store purchases from your iPod or iPhone to a computer
    i cannot re-download them for free
    Yes you can.
    Click on Purchase and iTunes will tell you that you jhave already purchased then and ask if you want to redownload them (for free).

  • After prompted to update 10.9.1, my MacBook Pro updates and went thru restart but failed...I tried to start my book and gray screen, Apple logo both on, chime sounded, then went to progress bar, less than half macbook shuts down...did few times, same!!

    After prompted to update 10.9.1, my MacBook Pro updates and went thru restart but failed...I tried to start my book and gray screen, Apple logo both on, chime sounded, then went to progress bar, less than half macbook shuts down...did few times, same!!
    Go to system repair, there is a prompt that cannot repair live etc....I don understand!!! Help, I need the book for work tomorrow!!

    Thanks clintonfrombirmingham...
    After clicking "repair disk" it says DISK UTILITY STOPPED REPAIRING MACINTOSH HD, DISK UTILITY CAN't REPAIR THIS DISK. BACK UO AS MANY OF YOUR FILES AS POSSIBLE, REFORMAT THE DISK, AND RESTORE YOUR BACKED -UP FILES....
    written in red: ERROR: DISK UTILITY CAN'T REPAIR THIS DISK,,,DISK, AND RESTORE YOUR BACKED-UP FILES.
    how can I back up when I cannot even start my macbook? I am stuck here and have lots of important files in the hd... Please help me? Thanks you!

  • I bought a new Iphone 5 Friday the battery goes flat in less than half a day also the wifi disconnects in less than 40 secs

    I bought a new Iphone 5 Friday the battery goes flat in less than half a day also the wifi disconnects in less than 40 secs this is really frustrating I think I have a dud phone or is this the new IOS6.1 software update?

    Basic troubleshooting steps clearly outlined in the User Guide are restart, reset, restore from backup, restore as NEW device.  If you've been through ALL the steps listed and you're still having problems, then you'll need to bring your phone into Apple for evaluation and possible replacement.

  • My iPhone 4s shuts down with just less than half the battery remaining

    My iPhone 4s shuts down with just less than half the battery remaining. Is my battery shot?

    Hi LucMiranda,
    Thanks for visiting Apple Support Communities.
    It sounds like your iPhone is not behaving correctly. The steps in this article can help with troubleshooting the battery issue you're seeing:
    iPhone and iPod touch: Charging the battery
    http://support.apple.com/kb/HT1476
    iPhone or iPod touch displays the low-battery image and is unresponsive
    If you see the image below, charge the iPhone or iPod touch with USB power adapter for at least 15 minutes.
    You should see this image when iPhone or iPod touch begins to charge:
    If the screen still displays the low-battery icon, try turning the iPhone or iPod touch off and then on again.
    If the issue persists, follow these troubleshooting steps.
    Cheers,
    Jeremy

  • After the recent download, my ipod space said that I had reached capacity. Before the upgrade, I was less than half full...why?

    After the recent download, my ipod space said that I had reached capacity. Before the upgrade, I was less than half full...why?

    ***after the most recent UPDATE...

  • Photosmart 5520 showing new cartridges as less than half full

    I've just replaced the three colour cartridges with genuine HP cartridges.
    There are no printing problems, no error message, yet the Cyan and Blue cartridges are only showing less than half full. The yellow one is showing full.
    I've tried all the steps on the trouble-shooting page here  but no change.
    Is there a solution?

    Hi gordonbp,
    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I see that the colour ink cartridges are not giving an accurate reading. I do have a couple troubleshooting steps that I would like to run through to see if we can get this issue resolved for you.
    First off, if you have the printer power cable connected to a power bar/strip, please remove it and connect the power cable direct to a wall outlet.  Here is a document that explains the Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector.  Please note that the printer that is listed in this document is a LaserJet printer and that this is only used as an example seeing that the power issue applies to HP products in general.
    I would also suggest that you attempt to reset the printer once the power cable is in a wall outlet. Here is a document that explains how to do a basic Reset on the printer.
    Thank you for your time.
    Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    W a t e r b o y 71
    I work on behalf of HP

  • HP Officejet Pro 8500 A909g new ink levels drop to less than half after few pages.

    Installed all new HP940 ink cartridges and the levels dropped to half after only printing less 12 ink defective pages. Quality Diagnostics Page shows colors but black ink does not show up at all.  Self Test Diagnostic page shows printhead status is good. Checked the ink tubes and they are still neatly bundled and no signs of leakage. 

    Hello TV60,
    I see that the Officjet 8500 a909g is not displaying the correct ink levels and will not print black. You have done a great job trying to resolve the issue already, some steps I will suggest you have already done but it wont hurt to go over them again.
    This HP link: Ink Usage in Inkjet Printers may help explain why the inks are not showing as full as you think they should be after just installing them.
    These HP documents: Printer Does Not Print Black Ink or Color Ink, or Prints Blank Pages & Troubleshooting Print Quality Issues are going to help you figure out if the print heads need to be replaced even though your Printer Status Report shows the health as "Good".
    I hope this helps.
    Thanks,
    JERENDS
    I work on behalf of HP
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

  • Podcasts - less than half will sync - is there a limit?

    Hi
    I've searched and found similar questions in this discussion, but found no solution. Only 142 of my Mac's 375 podcasts will sync to the iPod Classic 80G. HD is roughly half full. I tried resetting the iPod and I tried syncing with Podcast sync set to None and then again with it set to sync All Episodes of All Podcasts. No change in which podcasts will sync.
    Any idea where I should look next?
    Regards,
    Jerry

    HI Jerry,
    Have you tried using Disk Utility to verify whether or not there are any corrupted files on your iPod? You will need your Mac restore disk.
    Shut down your Mac. While holding down the C key, press the power button and insert your restore disk, keep holding down the C key until you see the Apple logo. You will be prompted for a language selection, select English. From the Menu Bar, select Utilities/Disk Utility. In the DU window, select your iPod in the panel on the left, then click Verify. If DU reports errors, click Repair. When it's finished, Quit Disk Utility. From the Menu Bar click Utilities/Startup Disk. When the next window opens, click MactinoshHD 10.5.x and click restart.
    Try deleting this file also: com.apple.DotMacSync.plist
    /Users/YourName/Library/Preferences. From the Preferences folder, drag that file to the Trash, empty the Trash and reboot. Your Mac will create a new preference file for you.
    Carolyn
    Message was edited by: Carolyn Samit

  • Cannot set section height to less than 220 twips - RAS

    I'm using in proc ras with the Crystal 2011 .NET SDK (version 12). I cannot set a detail section height smaller than 220 twip. It looks fine in the debugger after I set it but when I open the saved report the height is always 220 twips. I made sure there are no object larger than 125 twips and they are all positioned at the top of the section band.
    CrystalDecisions.CrystalReports.Engine.ReportDocument rd = new CrystalDecisions.CrystalReports.Engine.ReportDocument();
    ISCDReportClientDocument rcd = rd.ReportClientDocument;
    rd.Load(reportFilePath);
    ReportDefController2 reportDef = rcd.ReportDefController;
    CrystalDecisions.ReportAppServer.ReportDefModel.Section detailSection0 = reportDef.ReportDefinition.DetailArea.Sections[0];
    detailSection0.Height = 125;
    rd.SaveAs("C:\\TEST.RPT")
    Edited by: John Lobaugh on Dec 10, 2011 2:39 AM
    Edited by: John Lobaugh on Dec 10, 2011 2:40 AM

    Hi John,
    Need more info...
    CR 2011 does not have any SDK's included with it and CR 2008 is version 12.
    The SDK for CR 2011 is in CR for Visual Studio 2010 and is version 13.
    All of the runtime and installer for CR for VS VS 2010 is on this page:
    http://www.sdn.sap.com/irj/boc/crystalreports-dotnet
    Don

  • Cluster continues with less than half voting disks

    I wanted to try voting disk recovery. I have voting file on a diskgroup with normal redundancy. I corrupted two of the disks containing the voting disk using dd command. I was expecting clusterware to be down as only 1 voting disk ( < half of total(3)) was available but surprisingly clusterware kept running. I even waited for quite some time but to no avail. I did not have any messages in alert log /ocssd log. I would be thankful if experts can give more input on this.
    Regards

    Hi You can check the metalink notes
    OCR / Vote disk Maintenance Operations: (ADD/REMOVE/REPLACE/MOVE) [ID 428681.1]
    it says
    For 11.2+, it is no longer required to back up the voting disk. The voting disk data is automatically backed up in OCR as part of any configuration change.
    The voting disk files are backed up automatically by Oracle Clusterware if the contents of the files have changed in the following ways:
    1.Configuration parameters, for example misscount, have been added or modified
    2.After performing voting disk add or delete operations The voting disk contents are restored from a backup automatically when a new voting disk is added or replaced.

  • Wireless Download Speed Less Than Half As Fast As My Upload Speeds

    Is anyone else having this problem: I use Verizon Fios and currently have their 50/50 plan.  When I go to speedtest.net to check my speed I see that I'm only getting about 14 Mb download speeds but 42 Mb upload speeds.  I have checked my speeds on wired connection and get about 38-40Mb. My Specs:HP HPE-400yUsing the Ralink driver for Windows 7 (http://www.mediatek.com/en/downloads1/downloads/pcimpcicbrt2860rt2760rt2890/)I'm running Windows 7 (64-bit)PC is not more than 25ft from the router, almost a direct line of sight Any advice or help would be appreciated.  Thanks!

    conrad wrote:
    Your noise margin is on the high side and this will also affect your speed. you will need to have a stable connection for a further day ie 3 days in total before you can contact the mods.
    Hi conrad  also  the line is very short  look at the attenuation figure as Keith has posted  the reduction in noise margin would achieve nothing on adlsmax  as the connection is already at its maximum but gives spare noise margin  when the op gets on to adsl2+
    If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Maybe you are looking for