Set up airport express to airtunes & internet when ISP connect using PPPoE

Hi,
I got the following problem: I connect to the internet using airport extreme and the ISP use PPPoE protocol. Now I'm trying to set up my airport express to airtunes my music but the admin utility doesn't see it and it doesn't see the airport extreme as well. Internet connection works fine but cannot play music. any idea what I'm doing wrong? It seems that I have to change the settings to DHCP to make sure airport admin can see the two base stations but if I do so, internet doesn't work anymore.
thanks for your help
Stefano

Hi all,
I have again the same problem but cannot find the answer I found a month ago anymore. anyone can help with a tip and point me in the right direction?
thanks
Stefano

Similar Messages

Airport Express can't be accessed on network using PPPOE

Hey Guys
I have just got to my room at uni and set up my airport express to use the internet which is through PPPOE. Thats all working sweet, My printer which is on the other side of the room with the airport is plugged in and I am able to print but I downloaded the HP software which lets you receive scans and do a lot more with the printer but for some reason it can't be found and I can't work out why, I have tried everything on the airport express and I got the print out of the printers network settings and it says its offline yet it can still print perfectly.
any help? thanks

If your printer is ethernet capable, then you could plug into an ethernet port on the AirPort Extreme. If you are using the AirPort Express to "join" your wireless network have "enabled ethernet clients" on the device, you should be able to use the ethernet port on the Express as well.
The ethernet port is also "live" when you have the Express configured to "extend a wireless network".
If your printer is a USB device, then you will need to plug in directly to your computer for full functionality.

I accidentally set my airport express to base station when it should be my time capsule and can't set it back

I'm an idiot!
I have my Time Capsule as my base station. I have two Aiport Exrpres' that connect to them.
One of the AE's was not working right, so I went it, did a soft reset, and using the Airport Utility, I accidentally identified the AE as the base station.
I've now gotten the Time Capsule set as the base station, and of of the AE's working off of it...however, when I plug the other AE in, it trumps the Time Capsule and shows it as the base station, and then the TC doesn't work.
I've tried doing a soft reset, and then hitting forget, but I can't figure out how to how it show as the child to the parent (the TC), as the other AE does.
Help!!
Thank you,
Dennis

Thank you, that seems to have done the trick...I knew Apple would be much easier than Windows!
I appreciate your help!
Dennis

Airport Express with Airtunes help!

I'm new to the wireless world so my question is why would I get the blinking yellow light on my Airport Express with Airtunes even when I'm within 5 feet of my G4 that has a airport card installed (802.11B). I also tried putting it in the living room which is one floor down and got the same thing.
I updated the firmware for the Airport Express with Airtunes but have not updated the airport card in the G4 because I'm unsure at the apple download site which software to download.
System profiler reports the airport card is 9.52 firmware version.
So is this what I update to: http://docs.info.apple.com/article.html?artnum=120097
The music is only cutting out from time to time but I would still like to see a green light on the Airport Express, its odd that it blinks yellow stating that I have a weak connection.
I'm not sure updating the firmware will help the weak signal, I used the airport utility to setup the Airtunes, but maybe there is a different way to configure the network to make it stronger, like I said I'm totally new to this stuff.
Thanks in advance for any help.
Roger
2002 Quicksilver G4
1.47GHz GigaDesigns Single Processor
OS X 10.3.9
1.5 GB SDRAM
ATI Radeon 9800
Pioneer 107 DVD-RW
Logitech MX518 Gaming Mouse
Klipsch ProMedia 2.1 Speakers
G4 Quicksilver 2002 Mac OS X (10.3.9)
G4 Quicksilver 2002 Mac OS X (10.3.9)

The blinking light doesn't indicate a weak wireless signal, it indicates that you do not have an internet connection established.
Are you using the AE for music streaming without an internet connection?
Haven't tried this myself, but it might eliminate the blinking light:
1. Open Airport Admin Utility and double click your AE to open the configuration.
2. Select the Internet tab.
3. Set to configure manually and enter:
IP address: 192.168.1.2
Subnet Mask: 255.255.255.0
Router Address 192.168.1.1
DNS servers 192.168.1.1
If this doesn't work, there probably isn't much you can do except establish a good connection to another router to get the light to turn green. The above numbers shouldn't be terribly important either since you are just trying to get the Airport to think it has an established connection.

Problems Setting-up Airport Express to Play Music thru External Speakers

Hi:
I have an HP dv6500z laptop connected to an HP printer C6280 via LinkSys wireless network using the LinkSys 54G router and PrintServer. It works fine.
I purchased an Apple Airport Express and want to connect it to this network so that I can play songs from within iTunes through external powered speakers wirelessly. The powered speakers are connected to the Airport Express (AE).
The AE is plugged into the AC outlet and the speakers are turned on. The AE is roughly 10 feet away from the laptop/router, just across the room. The AE's
LED is flashing amber (It does not yet recognize the network). I installed the Airport Utility from the enclosed CD, downloaded all patch upgrades and it installed successfully.
Now, how do I tell the Airport Utility to recognize and connect to my existing LinkSys network, so that the AE recognizes it ? The instructions are not clear on this note...they say to run the Airport Utility and then follow the on-screen instructions. The instructions tell you that you will lose your wireless network connection if you continue...and you do if you try.
The same information comes up if you try to do a manual install.
How do I connect the AE to an existing network ? This information seems to be missing. If I go to the AirPort Utility Help and search and search on Setting Up AirPort Express, it tells me the following:
Connect your stereo or powered speakers to your AirPort Express using the mini-jack on the top side of your AirPort Express, and then plug your AirPort Express into a wall outlet.
Open AirPort Utility, located in the Utilities folder in the Applications folder on a computer using Mac OS, and in Start > All Programs > AirPort on a computer using Windows.
Click Music in the toolbar, and select the Enable AirTunes checkbox.
Problem: What Music in What toolbar ? I do not see this...
Enter an iTunes speaker name and password. This is the name displayed in the pop-up menu at the bottom of the iTunes window.
Problem: Where does this information come from
If you're setting up your AirPort Express for the first time, choose Assist Me from the Base Station menu and follow the onscreen instructions.
It seems like something is missing from the setup.
Aaah...Just for the heck of it, I went under Base Station > Assist Me
and told it to continue even though the dialog box said it would change the network.
It displayed a tabbed dialog box where I could configure the AirPort Express, including a tab named Music.
Note:
The following two items are listed in Apple's on-line Help inside of Airport Utility, and on the web, yet I did not see them inside of Airport Utility when trying t oconfigure my AE.
I did not see a checkbox to check, named Enable AirTunes.
I did not see any place for entering the name and password for my speakers.
I followed all of the instructions and things looked like they were going well until I clicked Finish.
Them it said something like it could not save the settings..try again.
Well, I did, but when I brought Airport Utility back up, it kept saying that it could not detect the AE,
and when I went under the Base Station menu, all items were grayed-out, so I couldn't do anything.
Please help... the instructions need to clearer and more detailed.
Thanx, Dale
HP dv 6500z Windows Vista New Airport Express

Hi:
Thanx for your reply.
After several more hours of trial & error over the weekend,
I finally have the Green Light (LED) on the Airport Express.
And it stays green, even if I unplug it from the AC outlet,
and plug it back in later. I have the green light so this
tells me that I have gotten past one hurdle.
OK...in order to get this far, I had the AE wired to the
laptop or LinkSys router via an Ethernet cable. How do
I go about making this a "wireless" connection. LinkSys
told me how to take my laptop from a hardwired connection
to wireless, but it doesn't address the issue when you have
a 3rd party device hardwired that you want to make wireless.
Side Note:
I have not tried this yet, but I found a note on the web that
stated something like this: after getting the green light,
this guy then disconnected the Ethernet cable from the AE,
unplugged the AE from AC power for a few minutes, plugged it
back in to AC power, and voila! ... he was wirelessly on his network.
OK...let's assume that my AE is now on the wireless network.
What type of special settings do I need to make inside of iTunes
in order to get sound to the speakers.
I have my powered speakers recognized by iTunes...I can select them.
But, it appears that something may be blocking my AE from talking to
my network...I keep getting a pop-up box from Symantec saying that it
is detecting a "virus" (for lack of a better term) at the IP address
that I set my AE to. Oh, yes...that's another question...
When manually setting up the AE, I have my router network's IP address
(dotted-quad) in the list of parameter settings, but...near the top of
the list, the Airport Utility software asks for your AE's IP.
Well, what is it ? Nobody has told me ... Where do I get it from ???
Or...do I assign an arbitrary value to it based on the dotted-quad below ?
The router has an IP address of something like 192.168.1.xyz. I know what
the xyz is for the router but, what number do I use here for the AE, or
does it matter as long as it isn't being used by another network device.
My network is static.
So, after using a number not used by my network elsewhere (that I am aware of,
and...inserting a $ (to specify hexadecimal format)in front of my encryption password, NOT the router password (they intermix the naming of these) I finally managed to get the Green Light on the AE. Note: I am using the WEP-64 bit encryption which is also refered to a "40 bit" (No..not hexadecimal..$40 = 64) which is 40-bit to which a random 24 bit is added to give you 64 bit encryption.
To summarize;
I appear to have the AE configured via hardwire (I have the green light).
In iTunes, I can see and select my powered-speakers from the drop-down menu in the lower right corner, but i am s not yet streaming (hearing) the music.
It appears that Symantic may be knocking me off the network, or not letting the AE talk to the laptop/router...I have not yet tried this, but another nugget that I found on this site says to go to System Preferences (where?), click on the Firewalls tab, click Advanced , and uncheck "Block UDP Traffic".
Is this what may be blocking my AE talking to the laptop/router ?
Any help/feedback would be appreciated...Thank you.
I'm getting close...but no cigar (yet).
DaleB

HT4259 Trying to set up airport express to extend my wireless network. Primary base station is a time capsule. Even when I plug in the airport express to mac it cannot find it.

Trying to set up airport express to extend my Wi-Fi network. Primary base station is a time capsule. Tried searching for airport express using Wi-Fi status, no luck. Even tried plugging airport express into iMac, still no luck. Airport express showing solid amber light. Thanks for any help.

Airport express showing solid amber light
Unfortunately, this can mean one of two things:
1) The Express is locked up and will need a Factory Default Reset procedure to try to return the device back to its original default settings so that it can be reconfigured again.
2) The Express is defective. If you cannot get the Express back to a slow, blinking amber light after a Factory Default Reset, the Express will need to be replaced.
Try the Factory Default Reset a few times and report back on your progress.
Resetting an AirPort Base Station or Time Capsule FAQ

Airport Express, Leopard and Internet Sharing

I have my internet connection running directly to my iMac's ethernet connection and I use the Internet Sharing option to share my connection with computers. I had been using my Airport Express just to connect to my iMac for Airtunes. My Airport Express has stopped working and is not located unless I shut off Internet Sharing, but if I turn that off, it will not let me set the Airport Express to connect to an existing network - I guess because the network does not exist because I shut it off to configure the Airport Express. This is driving me crazy - any thoughts?

Interestingly, it works again. To initially configure the Airport Express, I had to shut off internet sharing. I configured the Airport Express (I did a hard reset to clear everything out) using the Airport Utility and set it to join an existing network. Of course my network did not show up since I had shut internet sharing off, but I manually typed in the name and password that I had already set for the internet sharing. I also put in a name and password for the base station, but this isn't required.
Then I hit update and right when it says that the configuration has been changed and it is waiting for the Airport Express to restart, I turned internet sharing back on. I waited and after flashing yellow for a while it connected. I unplugged it and plugged it back in to make sure it was fully configured and it works. I have found in the past the unplugging and plugging back in solves a lot of problems too.
Now that it is all set up, I can see and reconfigure the Airport Express in the Airport Utility even when internet sharing is on.
Hope this helps.

Airport Express for AirTunes. Problems.

I have a Windows XP computer and Laptop with a Linksys G wireless router in my house. Laptop connects to the router wirelessly and the desktop is hard connected to the router. Everyone is talking to each other nicely and I decided to invest an Airport Express for the sole purpose of playing itunes from my computer on speakers in another room.
I bought the Airport Express and have had nothing but disaster. I don't want to use it to create another network, just to "join" my existing network. So the first thing I do is plug it in with only the speaker connection plugged in. I have not plugged in an Ethernet cable or anything else.
According to the "manual" it is supposed to go solid yellow, blink and then go solid green. Because my home network is PW protected, I would have thought it could not "connect" to it on its own, but from just plugging it in to the wall outlet, I never get solid green, just flashing yellow, which apparently is bad.
Anyways, I use the software (updated over the net of course) to set up and it is looking for a "base station" (which is confusing to me because I don't have an Apple base station, I have a linksys router and the stupid Airport Express box plugged into the wall). At any rate, it "finds" the Apple base station and appears to treat it as an unsecured Apple network, with some funny id. I do "manually configure" and I tell it I want to use it for AirTunes, and I don't want to create a new network, I want to join it to an existing network. I give it the SSID of my home network as well as the 64 bit encryption key (that is not autogenerated, but that I manually type in), and that's it.
While I am able to get a message that it is ready to use (and I no longer see "Apple XXXX" as one of the available networks when I scan for available networks) the light on the Airport Express never stops blinking yellow, and it has done something to my home network because my laptop now is unable to keep a wireless connection to the router. I checked all my settings and they all seem to be ok, my desktop which is hard wired connects fine, but my laptop either won't connect at all, or connects and then drops. I have re-started everything including the router (not re-set, just unplug and plug back in) but my laptop now is totally not connecting and the Airport Express still doesn't work.
Sorry for the rant, but any suggestions?

Hello Birdman325. Welcome to the Apple Discussions!
Because my home network is PW protected, I would have thought it could not "connect" to it on its own, but from just plugging it in to the wall outlet, I never get solid green, just flashing yellow, which apparently is bad.
Not necessarily. A flashing amber status light generally indicates that the AirPort Express Base Station (AX) is not connected to a network. Since the default configuration of the AX is a wireless Internet router, the flashing status light would be normal.
Anyways, I use the software (updated over the net of course) to set up and it is looking for a "base station" (which is confusing to me because I don't have an Apple base station, I have a linksys router and the stupid Airport Express box plugged into the wall).
The AirPort utilities are specifically designed to work only with AirPort base stations, so it would be normal for it to try to "find" base stations.
At any rate, it "finds" the Apple base station and appears to treat it as an unsecured Apple network, with some funny id.
Again, normal. Remember the default configuration of a powered AX is a wireless Internet router ... since you don't have it connected to the Internet, the utility will find it as a stand-alone wireless network that is unsecured.
While I am able to get a message that it is ready to use (and I no longer see "Apple XXXX" as one of the available networks when I scan for available networks) the light on the Airport Express never stops blinking yellow, and it has done something to my home network because my laptop now is unable to keep a wireless connection to the router.
Let's double-check your AX's settings ...
Perform a "factory default" reset of the AX
o (ref: http://docs.info.apple.com/article.html?artnum=108044)
To set up AirTunes on the AirPort Express Base Station (AX), either connect to the AX's wireless network or temporarily connect your computer directly (using an Ethernet cable) to the Ethernet port of the AX, and then, use the AirPort Admin Utility to check these settings:
AirPort tab
o Base Station Name: <whatever you wish or use the default>
o Wireless Mode: Join an Existing Wireless Network (Wireless Client)
o Wireless Network: <select the existing Linksys wireless network>
Music tab
o Enable AirTunes on this base station (checked)
o Enable AirTunes over the Ethernet port (optional)
o iTunes Speaker Name: <whatever you wish>
o iTunes Speaker Password (optional)
In iTunes:
iTunes > Preferences... > Advanced > General
o Look for remote speakers connected with AirTunes (checked)

Can I use Airport Express's Airtunes with a non-Apple modem/router?

I am about to set up a network in our second home, so I am trying to do it as economically as possible. I will have a Verizon modem/router. The Verizon rep says the Verizon equipment is all I need for a computer network (no Airport Extreme Base Station needed). But I would also like to play music on Internet radio stations through iTunes on my Cambridge Soundworks system in a room that is different from the one where the Verizon modem/router will be. Can I purchase an Airport Express with Airtunes to plug in near the music system without also getting an Airport Extreme Base Station to which the Airport Express would be linked? If it is possible to go with just the AE, is it foolish to avoid getting the base station if I would also like to have wireless printing on my network? (I believe I would need the Airport Extreme Base Station for printing because it has the USB port.)

The Airport Express will do what you want in addition to printing if your printer is compatible as it does have a USB port. Just configure the Express to "join" the wireless network that the Verizon router is creating.
You will be able to stream AirTunes to the AirPort Express, which in turn will furnish an audio signal to your stereo system.
If you want to be able to stream any audio source from your computer to the AirPort Express...not just iTunes audio sources...you might want to take a look at Airfoil.

I set up Airport Express as Client, I can no longer connect to my wlan

I set up Airport Express in Client mode so that I could use Airtunes. My Router/modem is a netgear one and I use WPA.
I can no longer connect to my wireless network from my ibook.
If I plug in the ethernet to the router I can. I can also then see from the router that Airport express has connected itself to the router.
So what do I have to do to be able to reconnect to myibook to the WLAN?

Double-check these settings on your iBook:
System Preferences > Network > Show > Network Port Configurations
- Verify that an AirPort option exists. If it does not, click "New" to create one. - Verify that AirPort is "On" (checked)
- Verify that AirPort is at the top of the list. If it isn't, you can drag it to the top.
Systems Preferences > Network > Show > AirPort
AirPort tab
- By default, join: Automatic
TCP/IP tab
- Configure IPv4: Using DHCP
- Configure IPv6: Automatically or Off
Proxies tab
- Configure Proxies: Manually
- Select a proxy server to configure: <All proxies should be unchecked unless you specifically require a proxy for Internet access.>
- Exclude simple hostnames (unchecked)
- Bypass proxy settings for these Hosts & Domains: <leave blank>
- Use Passive FTP Mode (PASV) (checked)

Using airport express with no Internet

Have a problem here that's quite complex.
We have a brand-new HP office jet Pro that appears to support AirPrint. We would like to be able to print from several IOS devices in the office -- iPhones and iPads. But for that to work the printer AND the IOS devices need to connect to the same Wi-Fi network (according to the HP printer documentation)
Yesterday we went and purchased a new airport express. But this AirPort Express will NOT be connected to the Internet. Each IOS device already has its own cellular Internet connection.
The issue we're seeing is this: Once the IOS devices connect to the Wi-Fi network they can no longer access the Internet, even through their cellular data connection.
Is there any way for an IOS device to connect wirelessly to a network that does not have an Internet connection while simultaneously getting its Internet from its cellular data?
Stephen

I have the same problem for different reasons. I set up Airport Expresses at a cabin for the single purpose of AirTunes, that is, playing music through speakers connected to the AE (actualy multiple AEs). One of the AEs creates a network, the others join it, and the iOS device can play through them. Mostly, though, we have a Mac on the network playing through all of the speakers.
The AE creating the network is not on the internet, so reports a problem which we ignore. However, two issues show up:
(1) iTunes on the Mac periodically wants to "phone home" to update a list of radio stations (who cares?!?) and stops with a dialog box reporting the error. This seems to be because iTunes is stupid (or the programmers are) and thinks it MUST update the radio list hourly even if I never listen to a streaming radio station, AND that this error is so critical it stops playing music until the user addresses the problem.
(2) The iOS devices think they should be getting internet over WiFi even though it's not available via that connection (same as Stephen's problem).
So it seems two issues exist.
(a) Make iTunes robust enough to live off the grid for a while even if there is a network available (or at least know the difference between a on-grid and off-grid network).
(b) Make the iOS devices aware of off-grid networks and revert to Cell for data connections, or better yet support multiple wireless connections simultaneously.
It would seem since this is a legitimate network topology there WOULD be a setting in the AE settings for No Internet, rather than Ethernet or PPOE only.

Trouble setting up Airport Express and Windows

I am trying to help a friend set up Airport Express to work with her Windows computer. The goal is to use the Airport Express so she can stream iTunes to her stereo system. There is an existing Linksys wireless network. First I tried to connect add the Airport Express to her existing wireless network. I was able to see the base station and I chose to add it to her existing network. I was able to go through all the steps updating the Airport Express. After the base station restarted, the configuration tool couldn't see the base station anymore. In iTunes on her Windows computer, I could see the base station but when I clicked to select the speakers, it wouldn't select.
I reset the Airport Express to factory settings and tried again with the same result.
I reset again and tried using the Airport Express to replace her wireless network and to also stream iTunes. In the configuration app I chose to create a new wireless network. I was able to set up the Airport Express as a wireless network and could connect her Windows laptop to the Internet through the Airport Express. But I had the same problem in iTunes: I could see the speakers in the drop down list, but I couldn't select them.
I've returned everything to how it was (Linksys wireless network).
Can anyone let me know how to make this work?
Thanks

As I mentioned in my post, I followed the directions exactly. I used the same set of directions in the previous post. At the last step of the set up, the Airport Express restarts. After restarting, I got an error saying the utility could not find the base station. I reset the Airport Express to factory settings and went through the steps again and had the exact same result.
I am using an Airport Express at home with a Linksys router and I had no problem setting it up to join my network. The only difference is that I use a Mac at home. The one I am trying to set up for my friend is with a Windows XP machine.
Has anyone ever had this problem?

AirPort Extreme + AirPort Express for AirTunes

Hi there,
I've just unpacked my new AP Extreme station (v7.3.2) as a replacement for the AP Express (v6.3) and it works just fine. What I now have been trying for some hours is to set up AP Express for AirTunes, but it doesn't work.
I just want to add AP Express to the wireless network created via the AP Extreme not to extend the network, but simply use AirTunes.
I tried the guided set-up via the Airport Utility, also the manual one. I tried to create a closed and normal network. The problem is always the same: After the update of the AP Express station, the station can't be found and needs a hard reset to start just another try for a set-up...only the AP Extreme shows up.
Any idea?
Thanks in advance.

...I solved it myself this morning at about 1.00 AM, but this page was down, so I couldn't post my message earlier...sometimes its easier than you think: I just forgot to enter the MAC address of the AirPort Express under the "Access" menu of he AirPort Extreme. That was the reason why the Express couldn't join the network created by he Extreme. The rest is as Nee Kun stated above with one difference: Once the Express is plugged in, I of course see/access (frankly you cannot see it, because its "closed"=invisible) only one network, but in my AirPort Utility I can see both, Extreme and Express

I can no longer access my Airport Express Base Station. When I plug it in, it keeps flashing orange. I cannot see it in the Airport Utility.

I can no longer access my Airport Express Base Station. When I plug it in, it keeps flashing orange. I cannot see it in the Airport Utility.
How do I fix this

If you're comfortable resetting all settings, unplug it, hold down the reset button and keep holding it in as you plug it back in - keep holding it for another 10-20s until the amber light flashes
Then, open airport utility, now you should be able to see the device either on-screen or in the upper left under 'other wi-fi devices'

How to set up Airport Express in Bridge mode for hotel use

Please provide step by step instructions on how to set up Airport Express in Bridge mode for hotel use. I do not have a computer with me, only an iPhone and AEX 802.11n.

+"Please provide step by step instructions on how to set up Airport Express in Bridge mode for hotel use. I do not have a computer with me, only an iPhone and AEX 802.11n."+
AirPort Utility is the application that must be used to setup and make any configuration changes to the AirPort Express. I'm not aware of an "App" for this.
If you could borrow a computer from someone there for 30 minutes or maybe use the computer in the lobby, you could download AirPort Utility and reconfigure your Express. To help with setup, use an ethernet cable from the computer to the Express to help AirPort Utility "see" the Express.
http://support.apple.com/downloads/#airport

Set up airport express to airtunes & internet when ISP connect using PPPoE

Similar Messages

Maybe you are looking for