Set up time capsule as wireless access point

I am trying to set up my old apple time capsule as a wireless access point for my girlfriend. She is at college and the university does not permit routers, so I am trying to set the time capsule up so that is just takes the hardwired internet and allows wireless access to the internet so she can use her iPad and MacBook Air on the wireless instead of having to use a gigabit adapter to use the ethernet. The time capsule has the newest firmware and she is running mavericks which has the newest airport utility software. However I am not sure what settings to use to make this work. I am fairly intelligent when it comes to computers however I am not very skilled in networking. If anyone can help I would greatly appreciate it.
Thank you in advance!

How old is the Time Capsule? Running what firmware?
You have a problem.. If you cannot use the TC in router mode, then you are going to have to use it in bridge.. and it then depends on if the Uni system will hand out mulitple IP addresses. .which I doubt. In the end you might be stuck.. and it is not possible really with any system..
Bridge normally requires that the TC take an IP address and then clients connecting to the TC wireless will also get IP addresses.. but if the uni system only hands out one address then the TC has already captured it and there are no more available.. but try that method first.. as it is the easiest.
If it fails there is a more complicated method.. where we can give the TC a separate static IP in a different IP range and the wireless will still be bridged.. so the MBA or the ipad can use the wireless.. but only one can ever be online at a time.
The only way around this is to use the TC as a router contra the rules in the uni.. although I would suggest the uni only cares if you break their system. Most people don't.. but I am unsure what happens if you do.
Ask their IT people how to use a wireless only device like ipad, when they only provide ethernet. You might find there already is a wireless internet system as well.

Similar Messages

Setting Up Time Capsule for External Access

Hello all,
I am trying to set up my Time Capsule to be accessed without local Wi-Fi. I can use Back to My Mac to access the Time Capsule from my iMac, but not from my iPhone as Back to My Mac isn't intergrated into iOS. I use File Browser on my iPhone to access my TC from LAN, and it seems likely the TC can also be accessed through 4G using File Browser, too.
My first question is, can the Time Capsule be accessed through the internet (by port forwarding or something)?
Second question if the first is possible, how do I do so? (step by step instructions please)
I have the latest model of Time Capsule and AirPort Utility.
Thanks!
- Noah

Filebrowser can be used to remotely access the TC.
There are instructions in the filebrowser website.. have you tried those?
http://www.stratospherix.com/support/gsw_timecapsule.php?page=6remote
The one area where I think you might have issues is global domain name.. as that has been problematic.
You really need a static public IP from your ISP for this to be successful.
See Tesserax doco on remote access especially the global domain instructions.
https://discussions.apple.com/docs/DOC-3413
There is a hugely better method BTW..
Buy a vpn router and substitute that for the Time Capsule.. which can then be bridged behind the router.
VPN client is built into iOS and every mainline OS available. It is robust and has far superior security.
Note carefully the method you are going to use with iphone is opening your TC to attack. They have hidden the SMB port, but in reality.. any hacker will one day do a port scan on you and find it open.. no matter what port it is translated to.. at that point your password will be the only thing stopping access to outsider.. and they can often get around that.. or mount Man in the Middle type attack, since passwords in SMB are not secure.
Not that I think a hacker is going to waste their time doing it.. but it is just so you know.. it is fundamentally wrong.

Set Up Time Capsule as Wireless Router - Now How set up Time Machine?

Time Capsule is performing great as wireless base station set up today. Extended the network and added AirTunes Airport Express - everything works great.
Started Time Machine to configure the TC as the backup device for TM. Time Machine prompts me to "Set Up Time Capsule" and clicking that button brings me to Airport Utility. But there are no settings in the Airport Utility which allow me to configure the Time Capsule as the TM backup location.
Any ideas? Thanks.

Thanks for your reply and the article. It turns out the problem was that when I initially set up the Time Capsule in Airport Utility I checked the "not now" box when asked if I wanted to set up the TC for Time Machine backup. (I figured I could easily come back later to configure the TC for Time Machine.) I had to restart the AirPort Utility process and revert the TC to factory settings and then re-configure the TC while also setting up the wireless network and the Time Machine at same time. All is well now and after 6 hours overnight for the initial backup my iMac is backed up by TM on a regular schedule.

Trying to set up Time Capsule for WiFi access with Linksys router

Problem: I must use a Linksys router to connect to internet, since I have my telephone connected to this router (Vonage). I have set up a Time Capsule and connected it to the Linksys router, which is NOT wireless. I would like to use the wireless capability of the Time Capsule to provide wifi connection for laptop computers. The Time Capsule's wireless network is visible to these computers, but they do not connect to the network, since the Time Capsule is not the source of dynamic IP addresses; rather, the Linksys router is the source for IP addresses on my network. What must I do to get IP addresses supplied to computers attached via wifi?

The Time Capsule was set up using bridge mode. My initial error was to use the WAN port. After switching to a LAN port to connect with the Linksys router, the laptop computer was able to connect to the network wirelessly, but it could not obtain web page from the internet.
The laptop is a Dell Inspiron 6000; with an ethernet cable attached to the Time Capsule, it receives an IP address AND it can obtain web pages from the internet. The command "ipconfig /all" issued at the DOS prompt yields approximately the following:
Broadcom... (this is the ethernet card) ... IP address 192.168.15.104, with the gateway 192.168.15.1 (which is the Linksys router)
Intel(R) PRO/Wireless... (this is the wireless card) ... IP address 192.168.15.103, with the same gateway.
I can ping the iMac from the Dell laptop; the iMac is connected directly to the Linksys router. Running ping 192.168.15.104 from Terminal on the iMac succeeds, while ping 192.168.15.103 does not.

Setting up WRVS4400N for switch & wireless access point

Howdy, first post here. What is the proper way to configure this device to act as a switch and wireless access point so I can connect it to a switch with router upstream? I have a DLink router that was easy: disable UPnP, disable DHCP, set an IP/Subnet, and it worked.
My main router has a subnet mask of 255.255.240.0 but in the WRVS4400N setup screen I only get a list box with a limited number of masks, all of which are 255.255.255.x. Is there any way to specify the 240?

No. You cannot use a subnet mask larger then 255.255.255.0 on Linksys routers. They are only built to handle 255.255.255.0 and smaller. I guess they consider a LAN which requires a larger subnet, i.e. expects to run more then 253 networked devices requires a larger router.
The only thing you can do is to choose 255.255.255.0 and to pick an IP address which matches the IP address from which you expect to do the usual configuration work. If you use 10.0.0.0/255.255.240.0 but the computers which have to configure the router are all in 10.0.1.0/255.255.255.0 you can use that subnet. This works with computers even if they have a different subnet mask.
Of course, you can set any IP address you want, even one completely outside your normal LAN in order to "hide" the web interface from the normal LAN operation. The IP address of the router in your setup is irrelevant for the switching and wireless access. Both operate on ethernet/MAC addresses and the IP address of the router does not play any role there. If you use the 10 subnet mentioned before you could as well leave the router at 192.168.1.1/255.255.255.0. Whenever you have to access the web interface of the router you must temporarily set a static IP address inside 192.168.1.* on the computer...

Anyone know how to set up mac as a wireless access point?

thats pretty much my question, i wanna access the internet on my nintendo DS and Wii

Hello and Welcome to Apple Discussions.
Although I'm not familiar with the Nintendo DS you can use the iMac as a Wireless Access Point by going Apple Menu > System Preferences > Sharing > and selecting Share Connection from: popup menu: however you connect and the choose Airport to share to.
This article refers.
Merry Christmas
mrtotes

How to set up the Time Capsule as an access point

Hi there,
I have home office and am having wifi-connectivity issues due to the layout of my home.
I'm getting the electrician to set up ethernet outlets in various rooms in my house so that I can get wired connections in several rooms. What I want to do is connect my Time Capsule to one of those ethernet ports (see the diagram below) so that I can still broadcast a wi-fi signal in my house while having wired connections elsewhere.
|->
Lan Port 1
Home Office (Laptop)
|
|->
Lan Port 2
Living Room (TV)
Modem
->
Wired Router
|
|->
Lan Port 3
2nd Bedroom (Xbox)
|
|->
Lan Port 4
Dining Room (Time Capsule)
In my research in how to set this up, I've come across documentation that shows how to convert an old Netgear/Linksys wifi router to an access point. Here's an example of the documentation I've run across: http://www.smallnetbuilder.com/wireless/wireless-basics/30338-how-to-convert-a-w ireless-router-into-an-access-point. What I haven't encountered is how to do this with a Time Capsule.
Here are my questions:
Do I just follow these instructions and substitute "Time Capsule" where the author references "AP"?
I currently have my network set up through the Time Capsule. Here are some of the things that I currently have set up and corresponding questions:
all computers can access the printer via wifi - under the above setup, will all computers (connected to the new network via wired OR wireless access) still have access to the printer?
I have my macbook set up as a media center for my xbox and PS3. The Xbox and PS3 connect to my macbook and access the movie files that I have saved on my Time Capsule and a 2nd HDD that is connected to the Time Capsule via USB - under the above setup, will I still be able to access those movies with my PS3 and Xbox via the macbook media center software?
Thanks a ton for any help or advice. It's much appreciated.

Excellent.. great to see people doing the job properly and wiring ethernet.
Here are my questions:
Do I just follow these instructions and substitute "Time Capsule" where the author references "AP"?
Apple system is slightly different.. although the AP method would work the TC has a programmed state for placing it in AP mode.
And Apple even documented it.
http://support.apple.com/kb/HT4260
The difference in your system, is you are not using an Apple primary router (I presume) but otherwise the same.
Any router setup as WAP, you bridge the router part.. and you use Same wireless name.. same security setting (WPA2 Personal is WPA2 AES and the only one suitable). Same passkey..
I would add one difference to the apple insstructions.. they depend on auto wireless channels working. IMHO, auto anything in wireless is akin to voodoo black arts and has more to do with beads and rattles than science. It works fine in some case.. terrible in others.. lock it down. Set the wireless yourself.. at 2.4ghz there are only 3 non overlapping channels.. 1, 6, 11 .. if you use 300mbit N on the main router, it will use 2 of those channels.. choose the third for the TC.
Of course the TC can also use 5ghz.. and I lock it down as well but that is more my control freak nature.. and strong skeptism of anything auto in the wireless world.
I currently have my network set up through the Time Capsule. Here are some of the things that I currently have set up and corresponding questions:
all computers can access the printer via wifi - under the above setup, will all computers (connected to the new network via wired OR wireless access) still have access to the printer?
I have my macbook set up as a media center for my xbox and PS3. The Xbox and PS3 connect to my macbook and access the movie files that I have saved on my Time Capsule and a 2nd HDD that is connected to the Time Capsule via USB - under the above setup, will I still be able to access those movies with my PS3 and Xbox via the macbook media center software?
Your number auto changed.. fun isn't it when i edit it shows correctly but when I post it changes the format.
On the new setup the printer will still be available to all clients .. whether wireless or wired.
And to second part, yes, all file access is not going to change.. well I don't predict any.. IP of the system might change around but overall you are creating a single flat network. And that will work fine.

Airport Express + Time Capsule and wireless access to internet

I have a wireless internet provider. It's an open access without encryption.
I would like to have the airport express connect wirelessly to the internet then connect the airport express by ethernet wire to the WAN port in the time capsule and then have a local encrypted network from the time capsule in order to access with my mac book wirelessly to the time capsule.
I tried all ways of configuring it but none worked.
Do you know if it is possible and what should I configure ?
If somebody can help me... I am getting crazy with that...

This will not work. The Ethernet port on the AirPort Express (AX) is active only when the AX uses WDS to wirelessly join a network. Unfortunately this requires you to be using a compatible base station to create the wireless network AND you must configure the base station and AX to connect using WDS.

Any way to set up Time Capsule as wireless router WITHOUT Airport Utility?

I'm Macless at the moment and I just had to reset my Time Capsule... now it's showing up as Apple Network blahblah and it's completely visible and unprotected.
Tried the usual 192.168.0.1, .0.2, .1.0, .1.1, .1.2 without any luck. Any way to do this? Do I need to be plugged in via ethernet?
Thanks.

AirPort Utility is the only way to configure the Time Capsule.

1242AG Wireless Access Point - Cannot Get DHCP IP for BVI1 interface - Multiple SSIDs...

Hello,
I am attempting to set up three Cisco 1242AG Wireless Access Points with multiple SSID's. I used the web interface and directions online to set up the two networks I want and at least one of the networks work wirelessly.
However, I have two problems:
The first, which is the most important, is that the "management" interface, BVI1, doesn't get an ip address from our DHCP server. I set the VLAN 60 (which you'll see in the documenation below) to be the native VLAN on the device as well as on the switch that the device is connected to as well as other settings in the configeration file below. Because of this, I can only manage the device via the console port which would be a huge pain once all of the devices are mounted.
The second problem is that I am not sure how to get both wireless networks broadcasting their SSID's. I have to manually type in the SSID for the second wireless network I have which I would prefer I don't have to. Anyway I can enable broadcasting on all of the SSID's?
Thank you for your time.
Regards,
Christopher Koeber
Using 7916 out of 32768 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP-18.wesleysem.edu
enable secret {Number Here} {Encrypted Password Here}
enable password {Number Here} {Encrypted Password Here}
aaa new-model
aaa session-id common
dot11 syslog
dot11 vlan-name Kresge vlan 20
dot11 vlan-name Library vlan 30
dot11 vlan-name Public vlan 60
dot11 vlan-name Secure_Public vlan 70
dot11 vlan-name Secure_Seminary vlan 80
dot11 vlan-name Server_Room vlan 1
dot11 vlan-name Straughn vlan 40
dot11 vlan-name Trott vlan 10
dot11 vlan-name Web_Room vlan 50
dot11 ssid (Secure) Wesley Campus
vlan 80
authentication open
authentication key-management wpa version 2
wpa-psk ascii {Number Here} {WPA Key Here}
dot11 ssid Public
vlan 60
authentication open
mobility network-id 60
username Cisco password {Number Here} {Encrypted Password Here}
username admin privilege 15 secret {Number Here} {Encrypted Password Here}!
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 80 mode ciphers aes-ccm
ssid (Secure) Campus
ssid Public
mbssid
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
bridge-group 254 spanning-disabled
interface Dot11Radio0.10
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface Dot11Radio0.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
bridge-group 20 subscriber-loop-control
bridge-group 20 block-unknown-source
no bridge-group 20 source-learning
no bridge-group 20 unicast-flooding
bridge-group 20 spanning-disabled
interface Dot11Radio0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
bridge-group 30 spanning-disabled
interface Dot11Radio0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
bridge-group 40 spanning-disabled
interface Dot11Radio0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
bridge-group 50 spanning-disabled
interface Dot11Radio0.60
encapsulation dot1Q 60 native
no ip route-cache
bridge-group 1
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
bridge-group 70 subscriber-loop-control
bridge-group 70 block-unknown-source
no bridge-group 70 source-learning
no bridge-group 70 unicast-flooding
bridge-group 70 spanning-disabled
interface Dot11Radio0.80
encapsulation dot1Q 80
no ip route-cache
bridge-group 80
bridge-group 80 subscriber-loop-control
bridge-group 80 block-unknown-source
no bridge-group 80 source-learning
no bridge-group 80 unicast-flooding
bridge-group 80 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
encryption vlan 80 mode ciphers aes-ccm
dfs band 3 block
channel dfs
station-role root
interface Dot11Radio1.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
bridge-group 254 spanning-disabled
interface Dot11Radio1.10
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface Dot11Radio1.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
bridge-group 20 subscriber-loop-control
bridge-group 20 block-unknown-source
no bridge-group 20 source-learning
no bridge-group 20 unicast-flooding
bridge-group 20 spanning-disabled
interface Dot11Radio1.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
bridge-group 30 spanning-disabled
interface Dot11Radio1.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
bridge-group 40 spanning-disabled
interface Dot11Radio1.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
bridge-group 50 spanning-disabled
interface Dot11Radio1.60
encapsulation dot1Q 60 native
no ip route-cache
bridge-group 1
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
bridge-group 70 subscriber-loop-control
bridge-group 70 block-unknown-source
no bridge-group 70 source-learning
no bridge-group 70 unicast-flooding
bridge-group 70 spanning-disabled
interface Dot11Radio1.80
encapsulation dot1Q 80
no ip route-cache
bridge-group 80
bridge-group 80 subscriber-loop-control
bridge-group 80 block-unknown-source
no bridge-group 80 source-learning
no bridge-group 80 unicast-flooding
bridge-group 80 spanning-disabled
interface FastEthernet0
ip dhcp client update dns
no ip address
no ip route-cache
duplex auto
speed auto
interface FastEthernet0.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
no bridge-group 254 source-learning
bridge-group 254 spanning-disabled
interface FastEthernet0.10
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
no bridge-group 10 source-learning
bridge-group 10 spanning-disabled
interface FastEthernet0.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
no bridge-group 20 source-learning
bridge-group 20 spanning-disabled
interface FastEthernet0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
no bridge-group 30 source-learning
bridge-group 30 spanning-disabled
interface FastEthernet0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
no bridge-group 40 source-learning
bridge-group 40 spanning-disabled
interface FastEthernet0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
no bridge-group 50 source-learning
bridge-group 50 spanning-disabled
interface FastEthernet0.60
encapsulation dot1Q 60 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
no bridge-group 70 source-learning
bridge-group 70 spanning-disabled
interface FastEthernet0.80
encapsulation dot1Q 80
no ip route-cache
bridge-group 80
no bridge-group 80 source-learning
bridge-group 80 spanning-disabled
interface BVI1
ip address dhcp client-id FastEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
end

I am using a third party DHCP server which is our Windows Domain Controller. I have the ip helper-address set for the native vlan of the Access Point through a layer 3 distribution switch (a Catalyst 4506) that the current switch connects to.
I didn't see any event on the logs for the AP.
Let me know if I need to do something else.
Thanks.

Can I disable my Verizon Fios Router Wireless radio, connect it to a switch and use my airport express as my wireless access point connected to an in wall ethernet port?

Here's the deal. I have a Verizon Fios MI424WR router. My house has CAT5 throughout the house. The media panel is located in the garage. I want to take the Verizon Fios Router and cannot it in the media panel so I can connect a switch to it, that way, all my CAT5 can fire throughout the house. Verizon being Verizon decided to connect the router directly in the office.
Can I go this route (Router in media panel, switch cross connect to it) and use Airport Express, connected to one of the in-wall CAT5 ports in my house and then set it up as my wireless access point to provide wifi to my portable devices (iPad, iPhone, Macbook)? Is this possible? Will Airport Express comminicate with my verizon router via ethernet in-wall? Do I have to turn off the wireless radio in the Verizon router? Any help would be greatly appreciated!

That is right, by hard wired I was just making clear wired vs wireless attachment. AirPort family of devices will only act in a repeater mode with their own family members, not FiOS routers. they have to be wired to work.
There are some useful docs you can download from Apple, Support, Manuals, Peripherals, AirPort (just follow thos links from the Support button on the top bar):
Apple AirPort Networks
Designing AirPort Networks
AirPort Express Setup Guide
The last has a diagram of what you are trying to do, though without the house wiring, etc., but the basic principle.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network.

How do i set up a wireless access point with ny time capsule

I am using a new Airport Extreme and want to utilize my older TC to create a wireless access point or maybe an aditional router using the same newtwork. What are the steps to set this up?
Thanks
Alamo

You will first need to perform a Factory Default Reset on the Time Capsule.
Resetting an AirPort Base Station or Time Capsule FAQ
Then, temporarily locate it in close proximity (same room or nearby) to the AirPort Extreme.
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click the tab in the upper left hand corner of the AirPort Utility window that reads Other AirPort Base Stations (1), then click the Time Capsule
AirPort Utility will take a moment or two to analyze your network, then announce that the TC will be configured to extend your wireless network.
Enter a name for the TC (you can use the same device name that you used before if you wish) and click Next.
AirPort Utility will take a another minute or two to configure the TC and then tell you that the setup is complete. Click Done
At this point, power down the TC and move it to a location that is approximately half the distance from the AirPort Extreme and the area that needs more wireless coverage.....to give the TC a good strong signal to "extend"
Power up the TC and wait for the green light and then you are all set.

Wireless Access Points - Time Capsule and Netgear

Ok...Netgear support site was completely useless so I am hoping that someone over here can help me out. I think what I am trying to do is relatively simple but for 3 days now I have gotten no-joy.
Here is my current configuration: Westell DSL Modem (wireless disabled) --wired-- Netgear WNR834B (SSID 1, operating b/g mode) --wired-- Time Capsule (SSID 2, operating n mode, connection sharing Off Bridge mode). All other devices are hanging off wirelessly to one of the two routers.
What I am trying to do is add a wireless Access Point (Netgear WN802T) to the picture. I need better coverage on the other side of the house and don't want to run wires. The WNR834B is WDS compatible but I can't figure out how to put it into repeater mode or bridge mode. So I thought my next best bet (before going out and buying even more hardware) would be to try and extend the TIme Capsule network. I have been unsuccessful so far (SSIDs are the same, channels are the same, WEP set because I read somewhere that WPA was not supported in repeater/bridge mode). Is it even possible to use a Netgear Access Point with the Time Capsule (I would think it would work, but I just can't get it to).
I can get the WN802T to be seen in my network, but I can not get it to carry the internet connection.
Any advice or steps would be GREATLY appreciated.
Thanks in advance for any/all help

friars, welcome to the discussions!
Sorry, but the possibility of extending the wireless network created by the Time Capsule with a device from another manufacturer is almost zero. Based on information from other top users, the only Netgear model that is shown as WDS compatible with an Apple base station is a model WGR614 v6.
Take a look at an Apple AirPort Express to "extend" the network created by the Time Capsule. While the Express will also do WDS, the bandwidth on your network will be cut by 50% with the addition of just one WDS device. The "extend" feature on the Express does not impose this type of penalty and it is fully WPA/WPA2 capable as well, much more secure than WEP.
For about the same money as an Express, you might also consider ethernet power line adapters. Almost as good as having a direct ethernet connection. Available from Netgear, Linksys, and others.

Setting up Time Capsule as "Access Point" and not using router feature

I would like to use my Time Capsule as a wireless access point for a laptop. What settings in Airport Utility do I need to make?
Here's my setup:
Internet -> DSL Modem -> Linksys (wired) router -> Ethernet Switch -> Time Capsule.
Connect Using: Ethernet
Configure IPv4: Manually
IP address: 192.168.1.20
Subnet: 255.255.255.0
Router: 192.168.8.1
Connection Sharing: Off - Bridge Mode

Follow up to my question.
Got my laptop to access the internet via the Time Capsule. How? By having my ethernet switch connected to the WAN port of the Time Capsule - not the LAN port.
Internet ->DSL Modem -> Ethernet Switch -> Time Capsule (WAN port)
I noticed that makes it so computers on my wired LAN can't use 'Airport Utility' to access the Time Capsule. I have to move the ethernet cable from the ethernet switch to a Time Capsule LAN port, in order for my wired LAN computers to see my Time Capsule.
Is there a way, so I don't have to unplug from the Time Capsule WAN - to LAN port?

Set up time capsule as wireless access point

Similar Messages

Maybe you are looking for