Set up time capsule with PC using ethernet

Hi,
I have a Time Capsule which I want to use as a wireless router.
I have two PCs - a desktop without a wireless card, and a laptop with one.
My internet connection requires a SecureID password, so whenever it disconnects (for any reason) I have to enter a new password.
To the best of my knowledge this can only be done from the AirPort utility - and that is only possible from a PC with a wireless card.
As the laptop is not always home, I'd like to be able to do this with my desktop, which is equipped with a wired LAN card and does not have a wireless card.
Is there a way to do this?
Thanks,
Omri

Thanks.
I tried it, and the airport utility just said that it cannot detect any wireless apple devices.
In the Time Capsule manual, it also says that the time capsule can be configured either by a Mac with wireless/ethernet or with a PC with wireless.
I solved the problem by buying a cheap PCI wireless card for my desktop.

Similar Messages

How to set up time capsule with BT Infinity

how to set up time capsule with BT Infinity

The easiest and sure way is to use bridge on the TC as the method of connection. The TC then becomes a device in your network and gets its IP from the main router that I presume BT supply.
Method is,
1. Plug the TC WAN port into the BT supplied modem by ethernet.
2. Plug the computer you are using for the setup into the TC by ethernet.
3. Run the airport utility .. go to internet tab on the top menu..
In the bottom option, Connection Sharing choose off (bridged mode)
4. Go to the wireless page and setup wireless connection as you like it.. using whichever band you want. And make sure security is set to the highest setting, wpa2 personal. Put in a decent wireless passkey.
5. Press the update and fix whatever else the TC will show as needing fixing.. usually security stuff.
6. You can then disconnect the ethernet and connect by wireless if you want. Any port on the TC will now be a LAN port, including WAN.
This is assuming BT supply a wireless router with built in vdsl/other type of modem. If so you normally will not be able to bridge the modem, unless BT are using pppoe authentication which they haven't in the past.
If you really need to use the TC as a router then you will need to work out an alternative method. You can double NAT by placing the TC in the DMZ of the BT router if that is an option. It is not without issues in general.

HOW TO SET UP time capsule with time machine?

I have not been successful in setting up time capsule with the time machine,can someone give me steps to follow?

What part are you having problems with? You need to make sure File Sharing is enabled on the Time Capsule (which is done in AirPort Utility). Then you just connect to the Time Capsule either wirelessly or via ethernet cable and when you go to Time Machine setup your computer should recognize your Time Capsule as a valid storage for Time Machine backups.

How to set up time capsule with ethernet?

How do I set up a Time Capsule using just ethernet? I have to do a complete backup (1 TB) (AGAIN!) and it will take forever using WIFI. And the instruction manual even says that the first complete backup should be done using just ethernet, --but you know what, it does NOT say how in the world to do that.
I thought I had stumbled into a few minutes ago, as I had turned off the WIFI and just had it connected to my MacPro just using an ethernet cable, and yet Time Machine was able to find it and start backing up to it ... but that shut off my internet connection! I couldn't log into this site or any other site until I pulled the power plug on the Time Capsule.
I have FIOS internet connected to my ethernet 2 plug and the Time Capsule connected to my ethernet 1 plug -- would it help if I reversed them?
This thing is seriously fouled up. Should have just bought a Firewire hard drive.

I thought I had stumbled into a few minutes ago, as I had turned off the WIFI and just had it connected to my MacPro just using an ethernet cable, and yet Time Machine was able to find it and start backing up to it ... but that shut off my internet connection! I couldn't log into this site or any other site until I pulled the power plug on the Time Capsule.
I have FIOS internet connected to my ethernet 2 plug and the Time Capsule connected to my ethernet 1 plug -- would it help if I reversed them?
Your TC setup is wrong.
You should bridge it.. If using Lion.. you poor guy.. expect endless networking issues..
This is not caused by the TC.. guess where the issue is??
To bridge you need to load in 5.6 utility because the one in Lion is useless.
Then see these instructions.. particularly the last bit for how to bridge.
https://discussions.apple.com/thread/4074627?tstart=30
Then plug the computer directly into the TC and all should work fine.. don't forget to turn off wifi otherwise it might slow it down still.

How to set up time capsule with BT home hub 4.0 & Openreach

Idiots guide needed.
My TimeCapsule (year old model) had been running well from my BT Openreach box (without using the Home Hub 4.0) but recently had issues with connection dropping - BT said they've sorted out their end and can't see any remaining issues and can't offer me any more support if I'm not using the Home Hub 4.0
I reset the TC to run straight from the Openreach Box still have issues with wi-fi dropping in and out (both on ethernet and wi-fi).
Can I:....
1) set up Time Capsule running from BT Home Hub 4.0 which itself runs from BT Openreach white box (thus continuing to get support from BT)
or should i go back to
2) Time Capsule running straight from BT Openreach Box
Can some one post an idiots guide to either option?
Other stuff that may be important.
Macbook air running Yosemite (mid 2011 model)
Apple TV
Airportexpress
Time Capsule
2 x iphone 4s
Kids PC
Ethernet and wifi for above - I generally run everything hard wired via ethernet.

The easiest and sure way is to use bridge on the TC as the method of connection. The TC then becomes a device in your network and gets its IP from the main router that I presume BT supply.
Method is,
1. Plug the TC WAN port into the BT supplied modem by ethernet.
2. Plug the computer you are using for the setup into the TC by ethernet.
3. Run the airport utility .. go to internet tab on the top menu..
In the bottom option, Connection Sharing choose off (bridged mode)
4. Go to the wireless page and setup wireless connection as you like it.. using whichever band you want. And make sure security is set to the highest setting, wpa2 personal. Put in a decent wireless passkey.
5. Press the update and fix whatever else the TC will show as needing fixing.. usually security stuff.
6. You can then disconnect the ethernet and connect by wireless if you want. Any port on the TC will now be a LAN port, including WAN.
This is assuming BT supply a wireless router with built in vdsl/other type of modem. If so you normally will not be able to bridge the modem, unless BT are using pppoe authentication which they haven't in the past.
If you really need to use the TC as a router then you will need to work out an alternative method. You can double NAT by placing the TC in the DMZ of the BT router if that is an option. It is not without issues in general.

Time Capsule With Non-Bridging Ethernet connection?

Hi all,
I wonder if it is possible to connect the Time Capsule to an existing Ethernet such that it doesn't do bridging between the three Gigabit ethernet ports and the WAN port, but simply acts as if it was a device plugged into one of the "switch" ports, thus being a member of the network with an independent built-in three port switch. However, it still should do bridging between ethernet and AirPort...
Is this possible?
The reason why I'm asking this is that I experience difficulties in seeing Bonjour-enabled devices connected to the LAN ports of the time capsule, because bridging puts a border for broadcast and multicast packages, which are used by protocols like Bonjour (aka ZeroConf, mDNS...). I can access them if I know their IP addresses and the TCP ports the services are on I wisch to use, but certainly it would be nicer to just have them appear in the Finder...

I saw that, in fact, the broadcast / bonjour issues were most likely because of a firmware bug, because after I upraged to a new firmware version, everything worked fine, and the built-in switch showed the expected behavior...

Set up Time capsule with USB modem

HI
I'm relatively new to my mac & I just purchased a time capsule. I use a Verizon USB modem for internet and this has caused me some problems trying to set up the TC.
Is there anything any one can tell me to help? I could use some step by step help. The light is green, says I was successful but I can't print & have not even tried anything else. I just know my internet connection is wrong.....
Any suggestions would be appreciated!

I was hoping I could set it up for remote printing & backup w/o using internet connection. No?
Although the Time Capsule (TC) could be configured a number of ways, having a USB modem will limit you somewhat. I am assuming that your modem is not wireless and that you connect your MacBook Pro directly for Internet access using an USB cable ... correct?
Since the modem doesn't have an Ethernet port, the only option you will have for the TC is to operate it as a wireless network ... basically its default configuration. You then have two choices on how to connect your MBP to the TC: by Ethernet or wirelessly.

Trying to set up time capsule with airport exteme. Apple advises to use manuel setup and click on Advanced. Then enter mobileme ID. I did this but Time Machine doesn't display anything on the capsule window.

Can't set up my time capsule on Airport Extreme (updated). Apple instructions are to use manual set up. Click on Advanced tab. Click on Mobileme and enter Mobileme ID and password. I did this. But Time Machine window is blank. Tryed to click on update window after entering Mobileme ID but Airport does not respond (turn of then on)

mickair wrote:
I have been experiencing some networking problems
Welcome to Apple's discussion groups.
I have the latest Time Capsule ("TC"), an old Airport Extreme Base Station ("AEBS") bought in 2007 and 2 Airport Expresses, one bought in 3 months ago ("AE-Alpha") and the other bought back in 2007 ("AE-Beta"). All of them have been updated with the latest firmware.
Based on those dates, the AirPort Extreme is probably flat (as opposed to dome-shaped), making it 802.11n-capable. The Newer AirPort Express is probably an 802.11n-capable model A1264, while the older one is probably a model A1084 or A1088.
I use {the TC's} DHCP function ... to avoid unauthorized use.
This a discussion for another thread, but that's not what DHCP is for.
The wireless setting for it is to participate as WDS Main, but after reading various posts, it seems WDS is a bad idea
With that older AirPort Express you're stuck with WDS unless you decide to replace it with a newer model.
The AEBS is currently setup as being a WDS Relay at the moment
Why a relay? That's only needed if there's another base station "beyond" it that is configured to depend on it.
Since the AEBS is connected to the TC via Ethernet, you should probably configure it as a "roaming network":
http://discussions.apple.com/thread.jspa?threadID=2273124
{The AE-Alpha} connects fine as WDS remote at the moment
I don't have any experience with mixed WDS and non-WDS networks, but since it's 802.11n-capable, you may be able to configure it to "extend" the network of the TC rather than as WDS. Look for a setting on the TC to "Allow this network to be extended".
Physical location:
AEBS in one end, TC and AE-Alpha in the middle while AE-Beta on the other end.
A device such as "AE-Beta" that's supposed to extend a network shouldn't be "at the end" but should be half way between the central base station and the clients that need an extended network.

How to set up time capsule with existing network that uses airport express/extreme

I have an existing wirelss network using airport express. I want to upgrade to time capsule and use the A/P express upstairs. I dont want to delete the existing network.

I suggest to use your airport express to extend your wireless network that is created by your new time capsule

Setting up Time Capsule with existing AirPort Extreme 802.11n and AirPort Express.

I already have and am using an AirPort Extreme 802.11n with an AirPort Express. I want to set up a Time Capsule 802.11n. Which is the best way to configure this?

... Which is the best way to configure this?
The answer depends on what you need the TC to accomplish. If all you need it to do is perform Time Machine backups, simply have it join your existing network in client mode. It would be if it were to connect to your existing router (presumably your Extreme), not through an "extended" wireless network (presumably your Express).
If you need the TC to "extend" your network so as to serve additional wireless clients, you can do that also. Configure it to "extend" the network created by your Extreme.
As you can see it's quite versatile.

How to set up time capsule with router

I have a router N 300 and would like to buy time capsule but I did not find any information how to set up bouth devises. Thanks

You can always bridge the Time Capsule.. it is easy. Once bridged the time capsule will no longer route. All routing is then handled by the original router.. N300 (which could be belkin or netgear and maybe other people call then N300). It will still work as a wireless access point.. unless you turn it off, a switch with WAN now allocated to LAN, and a network drive.
Just look up bridge.
But there are other ways to do things. You could replace the N300, unless it is a modem.. in which case you can bridge that and use pppoe client on the TC (if you ISP does pppoe).

How to set up time capsule with att uverse

So I'm thinking about getting a time capsule for my home network. I have several apple (Macbook pro, Ipad, Iphone) products and i think it would be convennient to have. The only problem I think I will be facing is seting up the time capsule along side with my Att uverse 2wire router. So i have several questions:
1) I have wireless receivers for my tvs that receive the signals from the main uverse 2wire modem/router. Now I read online that you can turn of the wireless router function of the main 2wire modem/router and just turn it in to a modem (from what I understood at least). So my question is if I turn of the wirless function of the main uverse 2wire router, will that affect me watching tv with the wireless recivers that uverse provided me???
2) I know I can probably go around the issue on question 1 by putting the time capsule in to bridge mode, but will I loose any functions on the time capsule by doing so? Will accessing the hard drive be possible if its on bridge mode?.
3) If getting a time capsule is not worth it bacause there is no way around the issues in the first two questions then is there another product that I can use that might be better for my situation?
Im no IT genius but I know my way around so I am comfertable trying to set it up I just need some guidence. Any help will be greatly appreciated it!!

So my question is if I turn of the wirless function of the main uverse 2wire router, will that affect me watching tv with the wireless recivers that uverse provided me???
The other receivers will not work if you turn off the wireless on the Uverse gateway.
I know I can probably go around the issue on question 1 by putting the time capsule in to bridge mode, but will I loose any functions on the time capsule by doing so?
The Time Capsule will need to connect to the Uverse gateway using an Etherent cable. The Time Capsule will be able to provide another wireless network when it is set up this way, but it will not be able to provide an additional Guest Network.
Will accessing the hard drive be possible if its on bridge mode?.
Yes
If getting a time capsule is not worth it bacause there is no way around the issues in the first two questions then is there another product that I can use that might be better for my situation?
This really depends on how many Macs that you need to back up. The Time Capsule can back up multiple Macs on a network. If you don't need that type of capability, then it would be much simpler, and a lot less expensive to connect a hard drive directly to your Mac and back up the Mac that way.
Half of the cost of the Time Capsule is tied up in a wireless router, so if you don't plan to use the wireless on the Time Capsule, you will be paying for features that you do not use.

How to set up Time Capsule with no internet or router wirelessly?

Hi, I would like to know if it is at all possible to setup a Time Capsule wireless without the use of Internet or a router altogether. I want to wireless set it up directly to a an Apple MacBook Pro.
Thank you.

If you decide to do this, the simplest way to accomplish your goal would be to download and install AirPort Utility 5.6 for Mac OS X Lion
Perform a Factory Default Reset on the Time Capsule to get it back to default settings using this Apple support document:
Resetting an AirPort Base Station or Time Capsule FAQ
Then open AirPort Utility 5.6 and click Continue to follow the guided setup to "Create a wireless network".
You will need to click "ignore" for messages that you see telling you that you do not have an Ethernet cable connected to the WAN port and also that you do not have an Internet connection.

How to Set Up Time Capsule With Airport Extreme and Airport Express

Just got a new 1TB Time Capsule. I want it to be the main base station for my network. I already have a network set up with an older Airport Extreme base station and an Airport Express to extend it. I am thinking that rather than setting up the Time Capsule to "join" the old network, the best approach is to disconnect the Airport Extreme and Airport Express and reset them. Then set up the Time Capsule as a brand new network and bring the reset Aiport Extreme and Express onto the new network as if my original network never existed.
Is that the right approach or am I complicating it? Can I just join the Time Capsule to the existing network and still make it the main base station for the network?

evelK wrote:
Just got a new 1TB Time Capsule. I want it to be the main base station for my network. I already have a network set up with an older Airport Extreme base station and an Airport Express to extend it. I am thinking that rather than setting up the Time Capsule to "join" the old network, the best approach is to disconnect the Airport Extreme and Airport Express and reset them. Then set up the Time Capsule as a brand new network and bring the reset Aiport Extreme and Express onto the new network as if my original network never existed.
Is that the right approach or am I complicating it? Can I just join the Time Capsule to the existing network and still make it the main base station for the network?
I'd first use AirPort Utility to "Save a Copy As" of your AirPort Extreme settings. Then disconnect it, connect the Time Capsule in its place, and use AirPort Utility's "Import" function to read those settings. (Both of those functions are under AirPort Utility's "File" menu.) You may have to adjust a few settings. Once you have the Time Capsule working as you want, you can reconfigure your AirPort Extreme unit as you wish.

Setting up time capsule with existing wireless router and another time capsule

Hello,
I just bought my first mac (MBP) and a time capsule. We already have a wireless router, and my brother has an imac and his time capsule connected to it. The apple support people said that i couldn't use my new time capsule as a backup for my files because it would have to be in bridge mode and that would cause all sorts of problems and the backup would probably fail. That I would have to use my brother's time capsule to back up my files.
Is this true?? I find it hard to believe this issue hasn;t come up before.
Thanks,
Deborah

Thanks, Bob! If I may impose on you a little bit more, would you be able to guide me a little bit in terms of the setup?
Would I need to connect my time capsule directly to the router for first time set up?
If so, would I have to keep it connected to the router all the time after the first time set up, or can I keep it in another room?
Our wireless network was created back when we were a Windows household, so we still control it using Network Magic on an old laptop.
I unlocked the network (using Network Magic) when I tried to set up the Time Capsule (wirelessly, and before calling Apple), and after entering the network password my macbook recognized the TC and I got the good little green light on the TC. As soon as I locked up the network, I got the flashing amber light on the TC and airport utility couldn't find it anymore (using Airport utility version 6.1)... I unlocked the network again, the light turned green. I locked it back up, the light started flashing amber again...
Thanks, I really appreciate your help!
Deborah

Set up time capsule with PC using ethernet

Similar Messages

Maybe you are looking for