Set up wizard claims no internet connection

Trying to run set up wizard for befw11s4 v.4 on win vista. The wizard keeps telling me that my computer is not connected to the internet, check the connection. Not sure where I went wrong.

Go to your internet browser and as if you were going to type in a web site address, type 192.168.1.1. The password should be admin unless you changed it.
I don't work for Cisco. I'm just here to help.

Similar Messages

  • Setting NAT to disabled breaks internet connection

    Hello when i set NAT to disabled my internet connections does not work. Why is that?  When NAT is disabled what attacks do i leave my self open to? My ultimate goal is to run three xboxes with open NAT setting, how do i do this? the details of my network are below.
    Modem --> WRT610n
    (everything is using statis IP)
    my desktop is plugged into the router via ethernet cable
    Wireless devices:
    3 xboxes
    2 Desktops
    1 laptop
    we are trying to get all three xboxs running with open NAT how do i do this?

    Why would you disable NAT? NAT is required to allow systems with Private IP Addresses to access the internet. For instance, if your PC has an IP Address of 192.168.1.50 it needs NAT to convert this non routable private IP address into something that is routable on the internet. NAT is designed to allow multiple systems within the private IP space to access the internet. Also, for systems that are not acting as 24/7 "Servers" why use static IP addresses? DHCP, when set up properly, eliminates user error by automatically entering the necessary information to allow workstations and game consoles to access the internet. No offense, but if you don't understand NAT and private vs. public IP addressing, you probably shouldn't be entering information into a static IP address config screen...The XBOX saying you have "Moderate" or "Strict" NAT has nothing to do with DHCP vs. Static IP.
    Open NAT should work correctly if UPNP is enabled on the router. If it doesn't, you can try opening the ports like the previous responder suggested but it shouldn't be neccessary.
    The router does allow for ONE IP address on your internet network to act as a "DMZ Host" which will bypass NAT and give that device unfiltered internet access but you will not be able to have 3 DMZ host devices. 

  • How can i set my ipod up without internet connection? Every-time I put my network in it say "Could not find network".

    My I-pod wont connect with the network, so I reset my I-pod to see if that was the problem
    and now I cant set my I-pod up because my I-pod cant find the network. I cant download I-tunes
    on my laptop because I have to have a password that I don't know.

    Try either:
    - On a computer that has iTunes and an internet connection
    - Go to a different location and try connecting to another wifi network

  • Setting up BD Live when internet connection in another room

    Hello,
    Just got a Sony BD and I want to connect it to BD Live in my living room. However, my computer and internet connection are in the family room. I don't want to send a LAN cable from my router to the back of the BD player. Can anyone give me some suggestion as to how to connect to the internet on my BD player? What adapters I might need. I'm sure it's probably simpler than I thought. Thanks for your help!

    I second Dave's suggestion.
    As an added alternative, you may want to take this opportunity to set up a wireless home network. Especially if you own(or plan to soon buy) a laptop. This will be a more expensive approach overall, but the rewards will greater.
    Disclosure: Former BBY employee.

  • Adobe Acrobat XI Pro free trial won't launch, claiming no Internet connection

    Hi,
    I wondered if anyone could help me solve this mystery: I am trying to launch the Adobe Acrobat XI Pro free trial. Sign In is required to use the trial. But when I click on "Sign in now", I get the message "Please connect to the Internet and retry". Which is strange, because  my Internet connection is active and stable. The same panel hints that my clock might be at fault (but it is correct). I am running Windows 7, no earlier version of Adobe Acrobat installed. I would greatly appreciate any suggestions you might have on how I can resolve this riddle.
    Thanks in advance,
    Andreas

    Hi SumitV,
    Thank you for answering and suggesting ways to remedy my problem. I tried all the four actions you made me aware of, but although everything seems to be all right, I still cannot launch Acrobat XI in the trial version. The only little hickup came when accessing Adobe's secure site, which prompted this message:
    But when I later checked the certificate, it seemed to be installed and enabled. I am no expert, but it looked like it should according to step 4 under http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-i ssues.html
    Regards,
    Andreas

  • Setting up itunes account without internet connection

    I wanted to set up my itunes account, but I do not have internet access for my home computer.
    Can I set up my account on a computer that is not my own?
    Would this cause trouble with syncing my iphone with my own computer?

    Rocky,
    You are right, and I apologize, I misunderstood the OPs question.
    Actually if you simply setup your network, but do not connect a cable to the internet, then you have your insulated network. As I understand it, with this setup the amber may still be flashing because it detects that you are not connected to the internet. But that won't prevent your local wireless network from working.
    To do this click "Internet" in the tool bar of the Airport Utility --> At bottom select Off (Bridge Mode)" beside "Connection Sharing".
    Let me know if this helps.

  • Help setting up Webstar Cable Modem internet connection

    Okay, i FINALLY have cable internet...and i just realized I don't know how to set it up....i've never been in the situation before...can any of you give me some resources?
    .:title edited by dibblethewrecker:.

    Okay, I'm using an onboard ethernet NIC.  I tried using the ubuntu live cd, but it won't automagically set up my network either. 
    I figured out my LAN card isn't even detected by my router so I'm using onboard NIC for the time being...my router detects that one.
    By the way I got a router....it is a LinkSys Wireless-G Broadband Router--model WRT54G.  But I'm not using the wireless portion on it.  My girlfriends computer is hooked up to it with windows, and it connects fine.
    I'm still not having much luck.  I went to that cable-modem howto in wiki, followed it to tdlp's DHCP mini-howto...it makes reference to a script called /etc/rc.d/inet...I don't have that one...should I?
    I would still appreciate any advice from you guys...thank you in advance.

  • TS1702 setting for what chat or internet connection through 3G

    I can use internect and whatchat now in locations without Wifi  service. Such occurence happened only after I reset my I phone to enable it to use Wifi service.
    I want to use both services in all situations.
    I think that there must be something wrong with my Setting.

    HI and Welcome to Apple Discussions..
    Sorry to tell you this but Norton anti virus software can actualy damage a hard drive.
    Read the second post here by: "Klaus"1
    http://discussions.apple.com/thread.jspa?messageID=10399395&#10399395
    There are no Mac viruses in the wild... it's not a virus.
    Before you erase the hard disk and reinstall the Mac OS X, run Disk Utility from your install disk.
    Insert Installer disk and Restart, holding down the "C" key until grey Apple appears.
    Go to Installer menu and launch Disk Utility.
    Select your HDD (manufacturer ID) in the left panel.
    Select First Aid in the Main panel.
    *(Check S.M.A.R.T Status of HDD at the bottom of right panel. It should say: Verified)*
    Click Repair Disk on the bottom right.
    If DU reports disk does not need repairs quit DU and restart.
    If DU reports errors Repair again and again until DU reports disk is repaired.
    When you are finished with DU, from the Menu Bar, select Utilities/Startup Manager.
    Select your start up disk and click Restart
    While you have the Disk Utility window open, look at the bottom of the window. Where you see Capacity and Available. *Make sure there is always 10% to 15% free disk space*
    If the hard disk appears to be ok and there's plenty of free disk space then do the Erase and Install, instructions here...
    http://support.apple.com/kb/HT1544
    Make sure and back up all important data BEFORE doing this.
    If you are running Leopard, the most recent version is 10.5.8.
    Carolyn
    Message was edited by: Carolyn Samit

  • Internet Connectivity wizard

    Hi all,
    |
    | Can anyone tell me what exactly should be filled into the fields of the
    | Internet Connectivity wizard to establish internet connectivity.
    |
    | The LAN server has IP address 192.168.1.1, mask is 255.255.255.0, and
    | the ADSL box is 192.168.1.254. This is the info filled in in the IP
    | Address Information section.
    |
    | The DNS section asks for a Domain, and Name Server 1, 2, and 3.
    | I fill in the domain name, and Name Server IP addresses of the ISP.
    | Here is where the wizard goes wrong. Connectivity cannot be established
    | and then I need to unload INETCFG and start again.
    |
    | The IP address of the ADSL box is public, the ISP is able to ping me.
    |
    | Can anyone offer some advise on how to configure these fields to
    | establish internet connectivity ?
    |
    | Thanks.
    |
    | Iwan A. El Wanni

    Originally Posted by AndersG
    Iwanelwanni,
    > So If I understand you correctly, I should make 192.168.1.254 a static
    > ip address in DNS ?
    > You are also saying I should be able to ping from the server ?
    > I am already able to ping the server 192.168.1.1 and 192.168.1.254, as
    > well as the name servers of the ISP, including the my assigned ip
    > address 200.2.172.200
    >
    Now you lost me completely. If I read you correctly then you have a
    public IP of 200.2.172.200? That is NATed to 192.168.1.1.
    In that case it would probably be best to reserve say 192.168.1.1 - 49
    as static IPs, then configure DHCP to hand out the rest as dynamic IPs.
    There is normally little or no need for your own DNS, instead use the
    ISPs DNS. Thus in INETCFG you enter the IPs or your ISPs DNS server into
    the DNS config.
    Then configure DHCP to hand out DHCP addresses and to use 192.168.1.254
    for default route and also hand out the ISPs DNS servers.
    - Anders Gustafsson (Sysop)
    The Aaland Islands (N60 E20)
    Discover the new Novell forums at http://forums.novell.com
    Novell does not monitor these forums officially.
    Enhancement requests for all Novell products may be made at
    Enhancement Request
    Dear Anders,
    After our last exchange I left this problem for awhile to tend to other ones, but now I would like to pickup where we left off.
    I have applied NW66SP7, and GW65SP6, and re-installed GWIA.
    In INETCFG I have set IP Packet Forwarding to ENABLED in the section Protocol -> Protocol Configuration -> TCPIP > TCPIP Protocol Configuration.
    In the same section I have also set LAN Static Routing Enabled, and Network Host 192.168.1.1 and next HOP 192.168.1.254, which is the gateway hardware on the LAN.
    Dead gateway Detection is also enabled.
    DNS Resolver lists the ISP's Name Servers IP addresses as 200.1.157.11 and 200.1.156.11. The domain name field is left blank.
    In the section Bindings -> Protocol to Interface Bindings -> Binding TCPIP to LAN Interface -> I entered the local IP address 192.168.1.1 , Mask 255.255.255.0. Deeper into this section I entered in sub-section
    Configure TCPIP Bind Options the following:
    Group Interface = Yes Set as Primary = Yes
    RIP = Enabled.
    OSPF = Disabled
    Expert TCPIP LAN Options -> Router Discovery = Enabled
    NAT: Static Only, and NAT Table200.2.172.200 as Public Address and 192.168.1.1 as Private.
    I have also created the IP address 192.168.1.254 in DHCP manually, and added option MTU with value 1450 (a necessity with our local ISP), Router with value 192.168.1.254, and Perform Mask Discovery with value true.
    After all this, I still cannot verify internet connectivity. Sending an e-mail through the GW client by entering the To address as: GWIA:"[email protected]" , I get the message:
    Some addrersses are undeliverable and have been crossed out.
    Would you like to go the addressbook to resolve them.
    I have performed Internet addressing rules routines in Groupwise, so this message should not appear. Since it does, I am concluding no internet connectivity exists.
    Please advise.
    Iwan A. El Wanni

  • Access Restriction - Internet Connection Policy (between two times)

    I want to say something about the Access Restriction.
    I set the policy for allow internet connection for one of my LAN PC's. For example, I set the policy to ALLOW internet connection EVERY DAY  from 8:00PM to 10:00PM. Starting with 10M internet connection stops. BUT, after a few minutes I do a power circle (turn OFF and turn ON the router) and I have internet connection again. For me, allowing internet connection from 8:00 PM to 10:00 PM means  to have internet connection ONLY BETWEEN THIS HOURS, not before and not after.
    In my opinion, this is the same situation with two DENY policies for internet connection, one from 12:00 AM to 8:00 PM and other from 10:00 PM to 11:55 PM (for the same PC, of course).
    Why POWER CIRCLE broken this policies ?
    ps - sorry for my English.

    @sunwatcher,
    If I set a policy for my little boy PCs ... for allowing internet connection from 4:00PM to 6:00PM (for example) ... after 6:00 PM internet connection stops and he turn OFF and turn ON the router (power circle)  and after that he have internet connection, from then for a long time ...
    I am from Romania, and I set time zone on GMT +2 (Bucharest time zone)
    I insist with this problem because I want for him to use internet only between two times. Outside this time frame I want him to do their homework.

  • Sharing airport express internet connection with router and wired network

    Dear,
    I want to set up the following network, but can't succeed.
    Components:
    2 Powermacs quad G5's (airport and two ethernet ports)
    2 Powerbooks G4 (airport and 1 ethernet port)
    1 broadband wired router (1 Wan and 4 Lan ports)
    1 airport express
    1 cable internet connection.
    1 LaCie Ethernet Disk mini 300 GB
    The internet connection is at the other site of the office (little architecture office). It is not possible to get the internetconnection directly to the desk wth the computer. 1 Powermac G5 is set up to share his internet connection. (Share via airport with ethernet 1). The ethernet 1 port is connected to the Wan port of the wired router. The other Powermac G5's ethernet 1 port is connected to Lan 1 of the router. The LaCie Ethernet Disk mini 300 GB is connected to the the Lan 2 of the router.
    All the conputers get their IP adresses bij DHCP. The router is set to distribute IP adresses. Without the router and the LaCie everything works fine. There is internet connection on every computer and filesharing in between them is possible.
    I like to be able to do the following.
    Use airport connection on the two powerbooks, for internet and access to the network. Use the wired connection between the powermacs and the lacie for filesharing. On the second powermac use internetconnection through the router. With this configuration is it possible to copy files fast between the powermacs and the lacie harddisk.
    At the moment I'm trying to get internet connection on the second powermac. The ethernet port gives me a proper IP-adress and tells me that I can connect to the internet, but it won't let me go on the internet and when I turn the airport back on, safari buggs. Without the ethernet cable connected I can go on the internet without anny problem, but off cours the fast filesharing isn't possible any more.
    A drawing of the desired network can be downloaded at the folowing website
    http://homepage.mac.com/maesen_jeroen/FileSharing14.html
    Is there a possible sollution to this problem?
    thank you verry much
    Jeroen

    Disable the DHCP server on your wired router. Since your Power Mac G5 Jeroen is sharing Internet, it is already providing DHCP.
    Use airport connection on the two powerbooks, for internet and access to the network.
    Sorry, but it is not possible for the PowerBooks to access the subnet created by the Power Mac G5 Jeroen.
    Use the wired connection between the powermacs and the lacie for filesharing.
    Shouldn't be a problem.
    On the second powermac use internetconnection through the router.
    On Power Mac G5 Jeroen, you will need to disable the firewall or open the ports through the firewall needed by Power Mac G5 Nico to access the Internet.
    Is there a possible sollution to this problem?
    What you have is incredibly complicated. A much simpler solution is to
    Get a 2nd AirPort Express (AX).
    Use WDS to wirelessly connect the 2 AXs.
    Connect an Ethernet switch (or hub) to the Ethernet port on the 2nd AX.
    Connect all of your Ethernet clients (2 Power Mac G5s and LaCie) to this switch (or hub).
    In this configuration your PowerBooks will have wireless access and all of your Ethernet devices will get IP addresses from the AX connected to the Internet.

  • Using cellphone as an internet connection?

    Ive been searching everywhere today to try and find out how to use my phones connection for internet. My comcast has been pinging 400-600ms the last few days so i'm looking for alternatives
    Macbook Pro
    LG Shine CU720 (AT&T)
    AT&T is no help, and neither is LG.
    please any ideas on the settings would be very helpful.

    i just got it finally connect so never mind.
    need to make sure everything is one default for your phone and turn on internet and bluetooth sharing for the macbook.
    open network preferences and create a bluetooth connection if you dont already have one. Configuration set as MediaNet (for AT&T) or whatever the setting name is for your internet connection on the phone itself.
    type in your cell #
    for at&t users:
    Account Name: [email protected]
    Password: CINGULAR1

  • Airport Express. No airtunes when there is an internet connection.

    Hello guys,
    Now I have my very own airport express problem. I will try to go into as much detail as possible.
    I own Airport express for about a month. It worked fine. Moved to the new apparent recently.
    I have HP Pavillion notebook. While without the internet in the new appartment i set up my AE to stream music to stereo in a bridge mode. It worked fine.
    Now my inet is on.
    I connected AE to modem via ethernet cable, set it in a bridge mode. After a while i got the wireless internet connection on my PC. When the PC is connected to the internet i cannot connect to the AE or get the Airtunes working.
    While reading the forums i've found out that i can change TCP/IP on PC to 164.192. and that will help me to connect to AE. I did, but at the same time the inet was gone.
    Summary: i have a working wi-fi internet connection while AE is in the bridge mode connected via ethernet to the modem, but have no airtunes. If i set my PC's IP to 164.192. i can get airtunes but no internet. Need to get this together.
    *The things i've tried already*: used AirPort Utility to set AE to "distribute IP", via DHCP. After that i rebooted my modem, AE and PC. PC and AE got IPs like 10.1.0. but no internet connection. Tech support of ISP said that it sees my PC, but PC has no IP on the net. While in this mode i also get the trouble connecting PC wirelessly to the AE and have to use hard reset to default settings for AE.
    Much the same result i get when trying to "share one IP via DHCP".
    Notes: PC's IP is set automatically. PC has internet connection via ethernet cable plugged directly into modem. Usual PC's IP is something like 77.122.
    As far as i understand the problem is with IPs.
    Please help me out. Thaks alot in advance.

    Ok, please try the following:
    o Power-down the modem, AX, and computer(s). Order is not critical.
    o While all of the network equipment is powered down, perform a "factory default" reset on the AX. When complete, power-down the AX.
    o Power-up the modem; wait at least 10-15 minutes.
    o Power-up the AX; wait at least 5-10 minutes.
    o Power-up the computer(s).
    Your computer should now be able to access the Internet through the AX. Please post back your results.

  • Is Internet Connect a startup application?

    Over the past week or two, after launching Safari or Firefox, the application indicates that it is not connected to the Internet. I need to go to Internet Connect (which is "idle") to manually connect to the net.
    Should Internet Connect be connecting to the net as a function of startup? Or is the connection to the net made when a browser is launched?
    I have dumped Internet Connect preferences but this makes no difference.
    Thoughts?
    Dennis

    Thanks for the help. I found the problem playing around in Network. I connect through Ethernet. For some reason when the Location is set to my provider (sympatico) Internet Connect does not start up. When I switch Location to Automatic, Internet Connect now functions properly.
    Thanks again for pointing me in the right direction.

  • Email Submit Opens Internet Connection Wizard

    Hello to all,
    I have forms developed in LiveCycle Designer 7.0. Functional tests from several different computers are fine (including some off-site). I have one computer that opens the internet connection wizard.
    When the submit button is clicked I get the select email client dialog box. The Desktop Application is selected.
    When the OK button is clicked, the Internet Connection Wizard opens!!
    The machine in question is running windows 2000 and office 2000. We found this problem initially while running adobe reader 7.0.5. Based on comments I have read, we un-installed 7.0.5 and re-installed 7.0.
    We still get the same response. What am I missing?
    Thanks,
    Pete

    Hi Pete,
    I am getting a similar problem. I am using EmailSubmitButton on my form and when I submit the form, it pops up the Select Email client window that has options to choose Desktop Email app, Internet email and other. I want to achieve the following:
    The user fills in email address on the form. I want to use this email address in the EmailSubmitButton. How do I set this via script?
    Also, when the user submits the form I don't want the email client window to pop up. It should email the form "silently" using the underlying smtp server. Is there a way to specify the smtp server via script?

Maybe you are looking for