Setting Default power on states for PCI-6723

Hi all,
I would like to set some digital lines in PCI-6723 as HIGH or LOW.For this i have made small exe of digital states and iam running while booting of pc takes place.but iwant to hide this execution while its running it should run once and quit , iam sending my programme please suggest,
Thanks and regards
labview boy
Attachments:
poweron.zip ‏162 KB

Hi labview boy,
You can try the suggestion in the following article as well:
How Do I Minimize a VI Without it Going Into the Task Bar?
Thanks,
Lesley Y.

Similar Messages

  • UMI-7774 - Setting default Power up outputs?

    Hi,
    I'm using a UMI7774, PXI7350, NI Motion 7.4.0.3002, and LV 8.2 I have a 24 V power supply connected to Viso on the UMI. When the PXI computer boots the general purpose digital output lines (table 3-9 in the UMI manual) on the 25-pin D-sub go to 24V and stay there until the board is initialized. Is there a way to set the default power up state to 0V?
    Thanks,
    Richard

    Hi Richard,
    Here is a knowledgebase document regarding how to change the
    power up state
    KB 2HA8B9YJ: How Do I Change the
    Default Power Up State of the DIO Lines on the NI 733x, 734x, and 7...Based on the setup configuration you have described, there
    is currently no direct method for accessing the DPull pin. One work-around
    would be to create your own custom cable in order to ground this pin.   Here is
    another document regarding how to do this:
    KB 47FARV4M: Creating custom cables
    for NI Motion controllers (733x, 734x, 735x) I
    hope this helps.  Please let us know if
    you would like further clarification or assistance regarding this issue.  
    Best
    regards,
    Vu

  • How to set default encoding and charsets for jsp and servlets.

    Hi,
    Is there any possibility to set default encoding or charset for jsps and servlest (for both request and response)?
    For example in Weblogic such parameters can be set in weblogic specific configuration files (weblogic.xml).
    Thanks in advance.

    Hi,
    I created one request with logo in the header an page in the footer etc. and called StyleSheet. After you can import this formats by each request.
    You can do this in compound layout.
    Regards,
    Stefan

  • How to set default .PDF file extension for Form Downloads

    I am trying to find a way of setting the PDF file extension when I download forms.
    I author the forms under a Plus subscription and am then downloading the forms under a basic subscription Collaborator account (diffrent person)
    If I don't include .pdf as the file type when downloading a form with a unique name as the Collaborator, it downloads without a file extension.
    Remembering to continually add the pdf file extension is a pain so I'm hoping there is away of setting this as a defaulet for my 'collaborator' account ?

    Firstly, apologies for multiple posts, I received messages saying my comment hadn't posted and also checked my history before re-submitting.
    Okay, the process is
    1. Log in as the Author account and I can rename the file without having to set the extension
    2. Log in as the Collaboartor account - same PC, browser etc and it doesn't save with a default file extension; HOWEVER, I have done this whilst also being logged in on a diffrent browser as the Author
    3 I have just tried logging out as Author and only being in as the collaborator and the form downloaded with a default PDF.
    4. I had someone else log in as the collaborator from thei PC and browser whilst I was still signed inunder my author account and again they were unable to save as PDF by default
    This has me wondering if there is anything at play when you've got multiple Users?

  • Set default File Export Form for Communication Medium?

    Hi,
    Does anyone know whether it's possible to set a default File Export Form for Communication Medium.
    For example, I created communication medium 'Direct Mailing'. Everytime when a user selects this communication medium in a Marketing Campaign, I would like the File Export Form 'Z_DIRECT_MAILING' to be selected automatically. Is this possible?
    Regards,
    Jeroen

    @ Rienk - That isn't my issue, what I was looking for was to have the last setting I selected (either in Batch Export or in QT Movie Export) "Stick" so when I go to do the next set I don't have to re-select all of my settings.
    @ Nick - Not a good thing in this case. I need to send out QTs that have the speed change "baked-in" and convert the format(to ProRes, so the Color Grading session using "Color" doesn't choke. I changed my Sequence: "Settings > QuickTime Video Settings > Compressor" to ProRes, but the "Current Setting" seems to stick to the original clip's capture format (XDCAM EX).

  • Set defaults on a Numbers for iCloud beta spreadsheet?

    Hi Everyone,
    How can I set page defaults on a Numbers for iCloud beta spreadsheet?  I want to have the size set to 100% and the  Format panel hidden.  At present I have to re-set these values everytime I re-open the file.  I have loooked in help but can't see any relevant info.  I'm running Mavericks.
    Thanks, Dave. D.

    Further to my post on April 23, I have noticed that when I save a numbers file on my Mac, all the changes I have made to things like the size, whether the format panel is visible, even the window extents etc. are all saved with the file.  Of course this is what you would expect but in the iCloud Beta version there is no Save command so I assume that is why these things are not saved.  Does anyone know if this is correct or if there is a work around?
    Thanks,
    Dave. D.

  • Set Default value in annotations for business service

    Can any one let me know how to set default value as null in annotations for a element.
    if I set it using wizard, it take "null" as string...

    In annotations ,Declare Data type as 'Entity'
    Thanks
    Amaresh

  • Set default Skin and Layout for all users

    Hi all,
    Im using UCM 10GR3 and i must set an default skin and layout for all users.
    Into General Configurations Field > System Variables i set
    LMDefaultSkin=MySkin
    LMDefaultLayout=MyLayout
    But this didnt work. Anybody have a clue?
    My skin is working fine but i have to change via My Profile.
    Best Regards
    Daniel

    only new users.
    According to metalink, each one of these will overwrite existing user settings.
    XuiSearchTemplate=slim
    XuiSearchTemplate=dam
    XuiSearchTemplate=myview
    XuiSearchTemplate=none

  • Setting Default or Derived value for watermark template

    Hi,
    I want to set default value for watermark template id. The condition is like if dUser(Logged in user) is "a", then default value of template should be "1". I have created template in pdfwatermark administrator with contentid of template as "1".
    How to write that idocscript?
    Thanks in advance

    Dear Kick,
    There is no such option of default scrap value in IMG. You will have to put that amount in asset master.
    If the data quantum is high then better to write LSMW or CATT
    Regards,
    Ajay

  • Where can one get power consumption figures for PCI-E Cards?

    as i wrote before im putting together a fairly decent rig, and im doing some heavy duty research into the actual total power requirement for it, using PSUCalc2003.v2 spreadsheet to calculate the total, however ive been unable to get the power consumption figures for my nvidia based graphics accelerator a Gigabyte Tech GV-NX62TC256DS with turbo cache, my guess is that this card is at the lower end of the power consumption spectrum but it would be nice to know the exact figure,
    any ideas on where can i get those figures ?
    thanks.....

    If you buy the 5770 from Apple as an upgrade kit it has the cable(s) - two for the 5870, one for 5770.
    If you bought a mac pro mid-2010 it may very well have come with cable(s), that I have never read or heard from others.
    OWC has not always inicluded cables but has charged extra, as they did with eVGA GTX285 where Apple sold with cables, and buying from OWC added another $30? or more to the cost with cables "extra" is what I recall.

  • Setting default unconditional mode(s) for a specific SID in TMS

    I am working in ECC 5.0, and I'm trying to configure one of the systems in our TMS landscape to use a specific unconditional mode (u2) by default.  Does anyone know a method by which I can set this in the TMS configuration?  I was looking at parameter R3TRANSOPTIONS for this, but after multiple searches on help.sap.com (and other sites), I cannot verify (1) that this will even work (2) if it will work, what the syntax for the call is.
    Thanks in advance for your help!

    Hi Katherine
    This is not possible with a normal import all job for TMS or other settings as far as I know. It is also not recommended that you would use an unconditional mode by default.
    The unconditional mode is specified by the tp process, so an R3trans parameter is not going to help. Their are a number of TP parameters as well, but no parameter is available for the unconditional mode in SAP.
    If you would absolutely need this, I think the simplest solution would be to create a custom program to do this, you can then program a report which uses the tp command with U02. You would have to be careful with authorisation of this report as it could be dangerous for end users to perform this.
    Reward points if useful.
    Kind regards
    Tom

  • Setting default "Initial View" options for new PDFs

    I usually want most of the PDFs I create to open with the pages panel displayed and “fit to window”. Currently I open every PDF and change that in the document properties under “Initial View”, save and close.
    There must be a better way.
    Is it possible to set this as the default for all newly created PDFs as part of the job options definition?
    I've searched in the different settings panes, but to no avail.
    Any hints appreciated.

    The Initial View (IV) settings are not part of the options when creating a new PDF, either in Acrobat or Distiller.
    There are several options to apply IV depending on the version of Acrobat you're using. You can create an Action in Acrobat X which applies IV to any open file as per your requirements, and optionally saves it as well. In Acrobat 9 or earlier you can do a similar thing with a batch process sequence.
    If you need to attach IV as part of the creation process then you can use an "epilogue.ps" script to add commands which Distiller will append to the PDF, and link that PS file to one of Distiller's presets.
    Lori Kassuba has a blog post about this method.

  • How to Set default Workbook as .XLS for Bex 7.0

    Dear Experts,
    I have a customised default workbook set for Bex 7.0. The Extention of this Workbook is .XLSM
    Currently it is not accessible using Excel 2003 due to format issue.
    1)Kindly let me know what should be done so that I can open this Workbook in Excel 2003.
    2) Suggest a way to set the default extension for Bex 7.0  "Custom" workbook (Not SAP standard, the option is available in Global settings-->Default workbook) to .XLS.
    Thank you,
    Nandita

    Dear Nandita,
    The only correction for this situation is documented on these two notes below:
    1339061 - BExAnalyzer: opening XL 2007 files in XL 2003 not possible
    1267924 - BExAnalyzer: Use XLS as File Format when using Excel 2007
       With Frontend Patch 800 a new property "Use XLS File Format" in "Global
       Settings" dialog is available when using BExAnalyzer with Excel 2007 and
       the SAP Default Workbook is being used.
    So, everytime when you created a new workbook, check the flag of "Use XLS File Format" checkbox and save the workbook.
    Then you will be able to open with Excel 2003.
    Best Regards,
    Edward John

  • [SOLVED] What sets default I/O scheduler for disks?

    Hi,
    having read the Wiki https://wiki.archlinux.org/index.php/So … _Scheduler , my attention got caught by the current I/O schedulers for my disks:
    SSD (two partitiotions: / and /boot, both ext4):
    # cat /sys/block/sda/queue/scheduler
    noop deadline [cfq]
    2 HDDs (part of ZFS mirror pool, partitioned by ZFS itself, mounted automatically on import by ZFS):
    # cat /sys/block/sdb/queue/scheduler
    [noop] deadline cfq
    I am about to create my own udev.rules to set noop and cfq for SSD and HDD, respectively. I just wonder, why all of them are not [cfq], which should be the default?
    P.S. I grepped all files in /etc for "noop" and "cfq" to make sure it is not some of my setting forgotten in time. And found nothing.
    Last edited by MilanKnizek (2015-04-22 08:32:59)

    The kernel config does I believe.
    % zgrep -i iosched /proc/config.gz
    CONFIG_IOSCHED_NOOP=y
    CONFIG_IOSCHED_DEADLINE=y
    CONFIG_IOSCHED_CFQ=y
    CONFIG_CFQ_GROUP_IOSCHED=y
    CONFIG_DEFAULT_IOSCHED="cfq"
    Perhaps zpools default to noop somehow.
    Last edited by graysky (2015-04-22 07:40:35)

  • How to set default object placement & wrap for drag-and-dropped files

    I am working on a document into which I need to drag-and-drop a number of files from the Finder: JPGs, PDFs, and so on. Each time I drag a file into Pages, by default its placement is set as "Floating (doesn't move with text)" and "Object causes wrap" is active.
    I would much prefer that the default settings be "inline" and "object does not cause wrap," so my drag-and-dropped images will appear within the text and move with it.
    Is there a way to change this default setting?

    Niel's suggestion is good. You might also try posting your question in the Tiger Server forums. I'm sure Tiger Server has several ways of dealing with this.

Maybe you are looking for