Setting order of connectivity between devices for Internet?

I have my macbook pro setup wth Access to internet via the airport AND also setup to use DUN via bluetooth.
I would like it to only goto the DUN if the airport is not availiable. Right now, I get the message that it con not connect to the device... then after a pause, about 30 seconds the interent goes live via the airort, I would like this reversed. Any Ideas on how to set this up?

Just go to the Network preference pane and have it show the "network port configurations". Here you can check which ones you want to use and which you don't You can also grab them, by the name, not the checkbox and drag them up and down. The system will search for connections starting from the top one and go to the next one if it can't locate a connection from the one above it and so on until it either finds a connection, or gives up and informs you that it cannot connect.
EDIT: someone beat me to it!!

Similar Messages

Setting up a Connection between Devices

I was wondering how to set up a connection between 2 or more Devices in Flash Lite and getting the IP addresses of these devices. Can anyone help me with this please?

Hi
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/10d1bde2-699f-2910-8e86-f46bfe045fdc
https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/52398597-0601-0010-868a-fd95f8061d85
https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/e04ebfdc-9916-2a10-2c82-fc057c8ced1c
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/6075d293-291b-2a10-7fbb-b827b28fd9b0
Hope it helps

How to connect to pc for internet

how to connect to pc for internet?

if you mean how to share the internet of a computer using wifi then
http://www.google.dk/search?source=ig&hl=da&rlz=1G1TSEH_ENDK367&q=share+computer +internet+connection+with+iphone&oq=share+computer+&aq=3&aqi=g5&aql=&gs_sm=e&gs_ upl=452787l455533l0l457616l15l14l0l5l5l0l213l1477l1.5.3l9l0

Time Capsule as remote device for internet connection sharing

I'm doing tech support for my parents. They have a Netopia DSL/4-port ethernet router/wireless router in one room. They just bought a Time Capsule. They have three laptops: one PowerBook G4 with airport. one PowerBook G4 without airport, and one iBook G3.
The Netopia router is in one room (Room A).
Mom's two airport-less computers are in another room (Room B).
I've set up the Time Capsure in Room B, with it set up to extend the wireless network from the DSL wireless router in Room A.
As far as a wireless Airport Disk, it works. However, when I use ethernet cables to connect the computers that do not have airport, I cannot get the airport disk to show up for either of them. Network preferences for each wired computer shows that ethernet is connected but that it has a self-assigned address and cannot connect to the internet.
When a Time Capsule is set up to extend a wireless network, can you use ethernet cables to hook up non-airport computers to the Time Capsule? Access the internet from it (DSL router - wireless to Time Capsules - wired to PowerBook G4)? Access the Time Capsules own drive (It's not showing up as a server in finder when connected via ethernet cable).

I assume you have configured the Time Capsule as a wireless client on this existing wireless network. "Extending" the existing wireless network with a Time Capsule (ie configuring it as a remote base station) is not possible, since the Netopia wireless router doesn't support this mode of operation of the Time Capsule.
Although not explicitly stated in Apple's documentation for the Time Capsule it is my assumption that the Time Capsule - when configured as a wireless client on a wireless network - does not have active ethernet ports and cannot be used as a wireless-to-wired bridge device.

Can I use the Airport Express to connect to a Linksys Wireless Network and then use the Ethernet port on the Airport for a wired connection to a device for internet access? Would I be able to then also use that Ethernet pt to a Ntwk Hub for more wired c

Thanks for the help. Looked but not clear on what I am trying to do as being possible. Can I use an Airport Express to connect wireless to a Linksys Wireless Router, such that I can then use the Ethernet ports on the Airport to either connected to a PC wired, or even use a hub off the Airport Express to allow multiple wired connections to it?
I am not looking to have the Airport Express extend my wireless network, just connect to it and provide me wired connections in a different location from where my Linksys Route is located. Would prefer to replace Linksys with all Apple, but just not possible financially yet. Thanks for the help.

If the AirPort Express Base Station (AX) is an 802.11n model, then yes, you can reconfigure it as a wireless Ethernet bridge. In this configuration, the AX would join the wireless network provided by the Linksys router and its Ethernet port would be enabled for either a single wired device or for an Ethernet hub or switch for multiple devices.

RV042 Windows incompatibility HTTP Connections between Subnets without Internet access

Hello,
We are a company of the banking sector
We have two RV042 Router.
One of this Router (R1) is configured for restrict users without internet access. This router doesn´t internet connections, the Wan ports are blocked.
Router 1: restricted users
Router 1 IP Lan: 10.22.4.1/24
Router 1 IP Subnet 1: 10.22.1.2/24 (For communication with Web Servers on Lan 10.22.1.0/24)
Pc1: 10.22.4.3/24
DNS: 10.22.4.51/24 (This DNS Server have an Internet connection through subnet 2)
The other router (R2) has an internet connection through the wan port for the access of the DNS Servers for respond to request of clients, and a web server in this subnet
Router 2: Web Server´s LAN and Internet Connection for the DNS Server
Router 2 IP Lan: 10.22.1.1/24
Router 2 IP Subnet 2: 10.22.4.2/24 (For communication with restricted user on Lan 10.22.4.0/24)
Web Server: 10.22.1.60/24
We need to access the web server from the network restricted users.
From Linux Operating System, the access to web server its ok
But, from Windows Operating Systems, we can´t access to web server. Time Out
So, we think that there are some incompatibility between the Router RV042 and the windows operating systems
On the website of microsoft, there is an article regarding an incompatibility issue with the RV042 which could help
http://support.microsoft.com/kb/934430
we copied a file attachment.
Thanks, sorry for bad English

Hi,
Have you also tested configuring static route?
I am asking that, because RV042 does not support VLANs and following that cannot do inter-VLAN routing. Configuring subnet with Multiple Subnet option is only giving access to this subnet to internet. Unless a static route is not configured as where this traffic to be routed in the LAN, the router itself normally will drop the packet.
If it works for you, this leads me to the thought that there is other routes that packets from LAN 10.22.1.0 to LAN 10.22.4.2 (and vice versa) are taking, but not necessarily the routers.
Here I can just give a direction of where to look, but if you think you checked all possibilities, it would be better to contact the support line. They will help as long as the device is under warranty.
Hereby the contacts:
http://www.cisco.com/c/en/us/support/web/tsd-cisco-small-business-support-center-contacts.html
Regards,
Kremena

How to set up internet connection between MacBook Pro and an old eMac?

I got an old eMac without wifi and a MacBook Pro. I'd like to share the network connection via ethernet cable to my eMac, but I can't get it work.
I'd like to use it with screenrecycler and it needs a network connection.
How to do it? How to set up the connection between the client and the host? Could somebedy give me a step by step guide?
Thank you very much

Hello,
First, are you using Wifi for Internet on the MBP?
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list, Wifi on the MBP.
In Shating on both, enable File Sharing, Screen Sharing, & Web Sharing on both.
Then with the Ethernet cable between the two, find the IPs of both, or use Finder>Go>Connect to Server>Browse... see what shows up.

Linksys E4200 - has to reboot to connect again with the internet

I bought the E4200 a month ago (replaced D-link DIR-655) and since then I have to reboot it twice.
I have a NAS connected to the router (and router to cable modem) and sometimes I have to FTP files from abroad. If I use the FTP too much time the E4200 just loose connectivity with the internet. Once home I have to reboot it in order to connect again with the internet. It never happen me before with the D-Link.
Does anybody has a similar problem?
Thanks!

Actually mine is working great now, almost as if it had a break-in period.
Mine has not flashed once in the past day (or more) and the last time I rebooted it was Wednesdsay evening (only to see if I could stop the flashing which was still happening
at that time).
I was also online on an interactive (gaming / gambling) site that is very quick to report what it considers "disconnects" if it sees any weakness in the connection to its servers and when using the E4200 it did NOT disconnect a single time all day yesterday.
(My Belkin N1 Vision wireless router connection via my Rosewill RNX-N1 USB adapter had been "disconnecting" multiple several days in a row although I was able to surf the web without issues while it reported me as disconnected).
Possible reasons everything is fine:
1) I placed the router's four ridiculously tiny feet on four thick wooden drink coasters
to give it more breathing room.
The flashing stopped a day or two later... (Keep in mind the router is less than a week old, so the reason it stopped flashing could be unrelated).
My wireless signal strength does seem to be sensitive to a 5.8 GHz cordless phone strangely even though it is a 2.4 GHz wireless adapter.
Just turning the phone (which has an INternal anntenna and is about 3 1/2 feet away from my wireless adapter at the moment) 15 or 20 degrees immediately changed the wireless signal quality from 4 bars to 3 bars and vice versa!!!
2) As far as my needing to reboot it that one time (during the first full day I owned the E4200):
I had been switching between two different model Rosewill wireless adapters a few times that afternoon (same chipset, same driver I believe and even show up as
same device in 32 bit Windows 7 Device Manager) without restarting the router after each switch
Since that one reboot, everything has been fine and my connection has been solid (pingtest.net tests over wireless produce an 'A' and speed has been for the most part relatively stable at 130 Mbps).
I hope thay helps others here (especially Part 1 above).
So overall I am extremely happy now.
I now just need to see what the implications are by the current lack of official IPv6 support in the E4200 (will post separately about that).
I noticed that my "IPv6 connectivity" on the wireless connection showed "no internet".
I just ran some IPv6 tests online (on two separate sites) and they passed and, lo and behold, now it shows "internet access" (again) for IPv6 (and not just IPv4 as it did before)!

Connection between 5508 WLC and 3750-24PS switch

I have to realize a connection between an 5508 WLC and 3750 switch using one SFP cable. I found on Cisco documentation some reference about two different SFP cables.
The first one is CAB-SFP-50CM, but this is used to interconnect two 3560 switches.
The second is SFP-H10GB-CU1M. This one has SFP+ transceivers on both ends which I don’t know if are compatible with the standard SFP ports that can be found both on WLC and switch.
My question is if I can use one of these cables in order to connect my devices, or if you know other one piece SFP cables.
Many thanks

I know that you can use those SFP transceivers, but I want to know if someone tried to use the SFP-H10GB cables for this kind of connection. Because I saw on another vendor website that the SFP+ cables are compatible with standard SFP ports, and I wanted to see if it is the same for Cisco cables too.
Regards

How do I setup MTP connection between Galaxy S2 and arch.

I am having difficulty in setting up a connection between my Galaxy S2 and arch PC.
I have installed libmtp and have run 'mtp-detect ' command in terminal this is the output I get :
[ram@Arch ~]$ mtp-detect
libmtp version: 1.1.1
Listing raw device(s)
Device 0 (VID=04e8 and PID=6860) is a Samsung GT-P7510/Galaxy Tab 10.1/S2.
Found 1 device(s):
Samsung: GT-P7510/Galaxy Tab 10.1/S2 (04e8:6860) @ bus 2, dev 3
Attempting to connect device(s)
PTP_ERROR_IO: failed to open session, trying again after resetting USB interface
LIBMTP libusb: Attempt to reset device
LIBMTP PANIC: failed to open session on second attempt
Unable to open raw device 0
Any Ideas????
I have searched Google & of course the forums and no good explanation or even a hint of solution is avalable.

praveenthivari wrote:
I have found a working solution for this.
Thanks to following forum threads:
http://androidforums.com/samsung-galaxy … alaxy.html
The process is longer but works fine to be able to mount the phone in USB mode.
1) Go to 'Settings' > 'Wireless and network' > USB utilities and press 'Connect Storage to PC'
2) A pop up will appear asking you to connect USB cable.
3) On connecting it will ask whether to mount as USB storage format. Click 'Yes'.
4) Done. It should now mount in USB mode.
It requires a bit of work but am satisfied that atleast SOME solution exists.
Any better solution?
Edit: I have found another site explaining this:
http://www.computerandyou.net/2012/01/h … -on-linux/
Unfortunately this is not an option for those of us using the Galaxy Tab 10.1, as it does not have the USB utilities option in the Settings menu. Shame on Samsung for making their devices different than any other Android device. MTP works great on my ASUS transformer, but not on my Galaxy Tab.

Which jar to use in order to write add-ons for IE

Hi,
I don't know whether I am asking the correct question but I want to know can I use any jar in order to create add-ons for Internet explorer and, if any, which one?
thanks

Hi Akshay,
I have used the FM "ISU_DB_EANL_UPDATE" in my project.
CONSTANTS lc_modify TYPE c VALUE 'U'.
CALL FUNCTION 'ISU_DB_EANL_UPDATE'
    EXPORTING
      x_eanl          = xw_eanl
      x_eanl_old      = xw_eanl
      x_upd_mode      = lc_modify
    TABLES
      xt_eanlh_update = xt_eanlh_mod
      xt_eanlh_old    = xt_eanlh_old.
where eanl is the entry in EANL table.
OLD_EANLH contains the old entry line item of the Rate Category table and NEW_EANLH contains the new line item to be added. This is the crude way of doing this. But I didnt find any other FM useful.
But this works.
Hope this also resolves your query.
Regards,
Manish
Edited by: Manish Bisht on Jun 29, 2009 3:43 PM

SSO Connection Between Netweaver CE 7.2 and MDM 7.1

Hi ,
I am trying to set up SSO connection between Netweaver CE 7.2 and MDM 7.1 systems in our landscape.
But Iam not finding the MDM template in Netweaver CE to create the MDM system in System configuration tab of CE.
Please help me on how to go about to create the SSO connection between CE and MDM system.
Regards,
Anand V

Hi Shiv,
The MDM content business package MDM JAVA WD FRAMEWORK 7.1 7.11 and MDM WEB SERVICES_RT 7.1 7.11 based on Note 1471326 have been Installed on CE but the restart was not taken.
Is the frestart necessary to get the MDM template?
Regards,
Anand V

I set up my daughter's devices under my apple Id. How do i get her her own apple id without losing everything on her devices?

Initially it was an ipod but now she has an ipad and iphone and we are sharing the same apple id/icloud. I would like to keep my apple id and get her a new one without her sacrificing her purchases/music etc...What is the easiest way, if any to do that?

Anb0329 wrote:
Initially it was an ipod but now she has an ipad and iphone and we are sharing the same apple id/icloud. I would like to keep my apple id and get her a new one without her sacrificing her purchases/music etc...What is the easiest way, if any to do that?
You can create a new Apple ID for her and set it up on her devices for iCloud and iMessage. Then her contacts and things can be backed up to iCloud under her Apple ID, and her iMessages will also be separate from yours.
You can, however, leave her iTunes, Music, and App Store with your Apple ID as before (you can use different Apple IDs for these different functions on iphones, ipads, Macs etc.). That way she keeps her music and purchases as before.
This article
Using your Apple ID for Apple services
explains more about different ways to do this.

Connect two vi via internet

hello,
I have these vis and I need to establish a connection between them via internet . in LAN the data is sent . but I don't know how to connect these vis internet.
any help please and thank you very much.
I have a static ip:80.81.xx.xxx
Solved!
Go to Solution.
Attachments:
data.llb ‏102 KB

Here you go
First do this: Go to Tools>Options. Then Select VI Server: Machine Access and place * to accept allow all incoming connections.
Then, do this : Enable Web Server. Change ports according to your requirements or try with default. I normally use 81.
Then the following:
And Finally this:
Here,you can open the VI on the remote PC.
If you want to remotely control the VI through internet, then go to Tools>Web Publishing tool and select your VI, select Embedded option, and allow control. Start the web server on the remote pc and you can control this VI through internet.
Hope this helps
-FraggerFox!
Certified LabVIEW Architect, Certified TestStand Developer
"What you think today is what you live tomorrow"

Successfully set up TC (the latest one) for MBP. I can access to TC wirelessly. Tried to access from my PC too but PC does not even detect TC (as storage), while PC is connected in the same network and can access to the internet. Anything missed?

Successfully set up TC (the latest one) for MBP. I can access to TC wirelessly. Tried to access from my PC too but PC does not even detect TC (as storage), while PC is connected in the same network and can access to the internet. Anything missed?

Load the airport utility for windows.. it has several parts.. the key one is bonjour for windows which helps windows find apple network devices.
The TC should also be setup with names that windows can use.. ie short, no spaces and pure alphanumeric.
So Fred Blog's Airport Time Capsule
Is not a valid windows name.
TCgen5 is.

Setting order of connectivity between devices for Internet?

Similar Messages

Maybe you are looking for