Setting PPPoE clients speed Via Cisco router
Hi i have a 7200 cisco router working as NAS (network access server) for PPPoE sessions , the clients connected DSLAMS and the Cisco connected to an AAA external Raduis server.
i want to set the user speed Via cisco router in a way which can be controlled in the Radius server , and not through the actual speed of the DSLAMS ports
Thanks alot
Hello Mohamed,
there is a feature called controlled subscriber bandwidth that may fit your needs:
see
http://www.cisco.com/en/US/docs/ios/bbdsl/configuration/guide/bba_con_sub_bdwth_ps6441_TSD_Products_Configuration_Guide_Chapter.html
it manipulates the ATM traffic parameters on a per user basis
these settings can be done on radius AV:
example:
The following example shows how to configure RADIUS attributes for a user profile for DBS:
[email protected] Password = "userpassword1", Service-Type = Outbound
Service-Type = Outbound,
Cisco-Avpair = "vpdn:tunnel-id=tunnel33",
Cisco-Avpair = "vpdn:tunnel-type=l2tp",
Cisco-Avpair = "vpdn:l2tp-tunnel-password=password2",
Cisco-Avpair = "vpdn:ip-addresses=172.16.0.0",
Cisco-Avpair = "atm:peak-cell-rate=155000",
Cisco-Avpair = "atm:sustainable-cell-rate=155000"
Hope to help
Giuseppe
Similar Messages
-
We have a need to netboot a PC with Linux via a Cisco router (I.E. PXEboot).
We have copied the PXE linux.cfg files to the Cisco router's flash, (Cisco 2821, IOS Advanced Security 15-1.2-T1).
We have setup the router as a TFTP server with defaulted path as tftp-server flash:tftpboot
From the pc's CMOS, we selected PXE boot.
With "debug ip packet detail", we can see the DHCP request from the PC.
We cannot however, get the router to download the Linux files to the PC.
Manually we tried:
c:\ tftp 10.0.0.1 get default - no go.
ANYONE have an idea????
Thanks
Frank/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";
mso-ansi-language:#0400;
mso-fareast-language:#0400;
mso-bidi-language:#0400;}
Hi Ash,
Thanks for the assistance.
The laptop is directly connected to the Cisco 2821 routers g0/0 interface.
The router is configured to be a DHCP server with the Cisco 2821 router IP address on g0/0 set in the DHCP configuration to be the default router. The router’s IP address is excluded from DHCP. (10.0.0.30)
If the laptop’s bios is set to PXE boot, it seems to receive an IP address from the router I.E. 10.0.0.1– verified by statically assigning another pc IP address 10.0.0.1– the 2nd pc receives an error of IP address conflict. Then set the second pc to obtain its’ IP address via DHCP, and while running debug ip packet detail on the router, I see the router running through the DHCP assignment process and finally assigns the 2nd pc 10.0.0.2.
So needless to say, I believe the DHCP setup is functioning correctly.
The problem we have at this point is nailing down the TFTP-server function running on the Cisco 2821 router.
We were able to create the directory tree on the Cisco 2821 routers flash and then copy the correct files into each directory within flash.
Using WinXP DOS prompt, tftp does not seem to function.
With debug ip packet detail running on the router and Wireshark running on the PC, we run from a DOS window c:\tftp 10.0.0.1 GET \default. No matter how we specify the path, end result is an error of some kind.
We watch debug and wireshark display the communications of the PC and router talking, but cannot seem to get the requested file.
Perhaps WinXP tftp server is flawed.
If we load TFTP32 and attempt to send and/or receive a file from flash, works fine.
The router tftp config is as:
tftp-server flash:/tftpboot/dsl/pxeboot.cfg
The actual files name is "default" and is found on the Cisco 2821 flash:/tftpboot/dsl/pxeboot.cfg directory.
No ACLs on the Cisco router and the router is pretty much right out of the box.
Firewall is disabled on both PCs.
Ping to/from the PC/router works fine.
Thanks again
Frank -
IDS shunning - IDS can't blocking via Cisco Router
Hello all.
I've configured IDS to shun with cisco router. I think all of setting fine, but IDS can't configure acl on the router via telnet.
Here is the output from ids using sh statistics networkAccess.
if you see the output, the state is Inactive.
Could you please let me know why the state is falling down inactive..
regards,
John.
IDS# sh statistics networkAccess
Current Configuration
AllowSensorShun = false
ShunMaxEntries = 250
NetDevice
Type = Cisco
IP = 192.168.1.10
NATAddr = 0.0.0.0
Communications = telnet
ShunInterface
InterfaceName = serial0/0
InterfaceDirection = in
State
ShunEnable = true
NetDevice
IP = 192.168.1.10
AclSupport = uses Named ACLs
State = Inactive <-- why???
IDS#This means the sensor had a problem either connecting to or reconfiguring the router.
What to do:
Configure network access to Disable Shunning and apply the changed config.
Now configure network access to Enable Shunning again and apply the changd config.
This will cause the network access controller to disconnect from the router and try to connect again.
Check the network access statistic and see if it is still inactive.
If it is then execute "show events past 00:10:00 to see all events in the past 10 minutes. Find the status event where you applied the change to Enable Shunning again, and start looking at the later events. Search for error or status events that might show what errors the network access controller was running in to.
Typical causes: Wrong username or password. Sensor is not able to telnet to the router because either the router is not reachable from the sensor IP, or the router does not have telnet enabled, or the router's access list prevents the sensor from connecting.
Other things you can check:
Create a service account on the sensor.
Login through the service account.
From the service account try to telnet to the router using the same username and password configured in the network access controller configuration on the sensor.
And see if you can get into the router.
You might also try running a sniffer between the router and sensor and monitor the connection. You can look for any error message coming back from the router, or at least see where in the connection the sensor is stopping. -
How do you to set an limit speed on your router port
Hi, I got a WRT300N and there 4 port. I like to know if we can set an limit speed on 1 of these 4 port? Example, my port 2 is using for download and I like to limit the speed like 50k/sec. If yes, please could you guide me how do I make the settings? Thank you
NO, there is no such settings on your Router, which will control your computer speed, Router will distribute the same speed on all the computers. May be you can search for some software we does that.
-
After installing the printer successfully on my desktop wireless through the cisco router I attempted to add my laptop a hp G60-635DX notebook. After installing the printer I got a message that a driver cannot be found! I called cisco and they offered online help for a $ 69.00 contract for 1 year! Looking for cheaper alternative!!!
Does the Asaro run DHCP? If so, turn off all access points except the one running DHCP and connect the printer. Then you can turn on the other APs.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP -
How access Office LAN via Cisco Router & Switches HELP!!
Hello everyone!
For starters I am no Cisco guru but at least find my way around a few things here and there.
I work as the IT dude for a company with two branches at different geolocations.
Our local network infrastructure at both HQ and branch offices comprise a Cisco 1941 Router and SF 300 24P Managed switches which hooks up our servers, workstations and VoIP phones.
The dedicated internet [DI] is connected via a Hughes radio link which belongs to the telco and on a different IP class and connects to interface 0/0 of Cisco 1941. Interface 0/1 is then connected to one of the SF 300 24P managed switches on another IP class for LAN [192.168.1/24]
I have three questions.
1. How do I access for example the File Server on the Corporate LAN from home?
2. How do I get workstations at branch offices authenticate with Active Directory Server at the HQ?
3. How do I get to get VoIP phones in branch offices hooked up to HQ VoIP PBX?
Thank you very much.Hello everyone!
For starters I am no Cisco guru but at least find my way around a few things here and there.
I work as the IT dude for a company with two branches at different geolocations.
Our local network infrastructure at both HQ and branch offices comprise a Cisco 1941 Router and SF 300 24P Managed switches which hooks up our servers, workstations and VoIP phones.
The dedicated internet [DI] is connected via a Hughes radio link which belongs to the telco and on a different IP class and connects to interface 0/0 of Cisco 1941. Interface 0/1 is then connected to one of the SF 300 24P managed switches on another IP class for LAN [192.168.1/24]
I have three questions.
1. How do I access for example the File Server on the Corporate LAN from home?
2. How do I get workstations at branch offices authenticate with Active Directory Server at the HQ?
3. How do I get to get VoIP phones in branch offices hooked up to HQ VoIP PBX?
Thank you very much. -
Not able to telnet or ssh to outside interface of ASA and Cisco Router
Dear All
Please help me with following question, I have set up testing lab, but still not work.
it is Hub and spoke site to site vpn case, connection between hub and spoke is metro-E, so we are using private ip for outside interface at each site.
Hub -- Juniper SRX
Spoke One - Cisco ASA with version 9.1(5)
spoke two - Cisco router with version 12.3
site to site vpn has been successful established. Customer would like to telnet/ssh to spoke's outside ip from Hub(using Hub's outside interface as source for telnet/ssh), or vise versa. Reason for setting up like this is they wants to be able to make configuration change even when site to site vpn is down. Sound like a easy job to do, I tried for a long time, search this forum and google too, but still not work.
Now I can successfully telnet/ssh to Hub SRX's outside interface from spoke (ASA has no telnet/ssh client, tested using Cisco router).
Anyone has ever done it before, please help to share your exp. Does Cisco ASA or router even support it?
When I tested it, of cause site to site vpn still up and running.
Thanks
YKHello YK,
On this case on the ASA, you should have the following:
CConfiguring Management Access Over a VPN Tunnel
If your VPN tunnel terminates on one interface, but you want to manage the ASA by accessing a different interface, you can identify that interface as a management-access interface. For example, if you enter the ASA from the outside interface, this feature lets you connect to the inside interface using ASDM, SSH, Telnet, or SNMP; or you can ping the inside interface when entering from the outside interface. Management access is available via the following VPN tunnel types: IPsec clients, IPsec LAN-to-LAN, and the AnyConnect SSL VPN client.
To specify an interface as a mangement-only interface, enter the following command:
hostname(config)# management access management_interface
where management_interface specifies the name of the management interface you want to access when entering the security appliance from another interface.
You can define only one management-access interface
Also make sure you have the pertinent configuration for SSH, telnet, ASDM and SNMP(if required), for a quick test you can enable on your lab Test:
SSH
- ssh 0 0 outside
- aaa authentication ssh console LOCAL
- Make sure you have a default RSA key, or create a new one either ways, with this command:
*crypto key generate rsa modulus 2048
Telnet
- telnet 0 0 outside
- aaa authentication telnet console LOCAL
Afterwards, if this works you can define the subnets that should be permitted.
On the router:
!--- Step 1: Configure the hostname if you have not previously done so.
hostname Router
!--- aaa new-model causes the local username and password on the router
!--- to be used in the absence of other AAA statements.
aaa new-model
username cisco password 0 cisco
!--- Step 2: Configure the router's DNS domain.
ip domain-name yourdomain.com
!--- Step 3: Generate an SSH key to be used with SSH.
crypto key generate rsa
ip ssh time-out 60
ip ssh authentication-retries 3
!--- Step 4: By default the vtys' transport is Telnet. In this case,
!--- Telnet and SSH is supported with transport input all
line vty 0 4
transport input All
*!--- Instead of aaa new-model, the login local command may be used.
no aaa new-model
line vty 0 4
login local
Let me know how it works out!
Please don't forget to Rate and mark as correct the helpful Post!
David Castro,
Regards, -
Help with Remote access VPN on Cisco router 3925 via Dialer Interface
Hi Everybody,
I need help for my work now, I appreciate if someone can fix my problem.I have a Cisco router 3925 and access Internet via PPPoE link. I want config VPN Remote Access and using software Cisco VPN client. But it doesn't work.. Here my config router :
HUNRE#show running-config
Building configuration...
Current configuration : 5515 bytes
! No configuration change since last restart
version 15.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname HUNRE
boot-start-marker
boot-end-marker
enable secret 5 $1$vEFw$rLfvLglzUgddCVwXDx03K.
enable password cisco
aaa new-model
aaa session-id common
crypto pki trustpoint TP-self-signed-1050416327
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1050416327
revocation-check none
rsakeypair TP-self-signed-1050416327
crypto pki certificate chain TP-self-signed-1050416327
certificate self-signed 01
3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31303530 34313633 3237301E 170D3134 30393235 31313534
31395A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 30353034
31363332 3730819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100CC79 74FCFABE 81183B70 5A9F4A53 EB609754 7D5F8587 9150B76E 3207A86E
5B65F9E9 6CDAC21A 6D69221D 1FF61632 14763308 43B2A1CC 8EE5ABAC EF07530E
3F0D35FE F08C955B 60B52B92 F8F54D53 DD6DD623 01F83493 02F9C49A F0C3483D
3B48A008 8D96700E 88924BFE DE00201B DE5965DE 32898CAD 9012AB55 76B6F39B
2D470203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603
551D2304 18301680 14C3418C BC35F3D9 B26B2475 2BB5F826 060525AB B3301D06
03551D0E 04160414 C3418CBC 35F3D9B2 6B24752B B5F82606 0525ABB3 300D0609
2A864886 F70D0101 05050003 81810070 AC7C26C6 4606A551 1A3FD6C5 2A5AEAE8
35DAC86E F8885E26 51F6EEAE 7565D3AA D532C8F3 55F6656F D103F38C 8FBDE7F1
83E77143 76469040 7FEA41E8 14963DB3 F7F28EA0 C5F2F42C B186B75C AAB04900
15F9CB38 A16964F5 4E7B4378 35041AA8 AE8EC181 D58D6A62 676E286A 7B9D80E6
35A0B9FB FB76E976 3D2A19D7 006078
quit
ip name-server 210.245.1.253
ip name-server 210.245.1.254
ip cef
no ipv6 cef
multilink bundle-name authenticated
vpdn enable
vpdn-group 1
vpdn-group 2
license udi pid C3900-SPE100/K9 sn FOC1823839B
license boot module c3900 technology-package securityk9
username cisco privilege 15 secret 5 $1$aAjB$D3iLyPFTE7O1bHPnKSJcH0
username kdhong privilege 15 secret 5 $1$nfyX$FO1BPTabCUaE6uKQwpLT.1
redundancy
track 1 ip sla 1 reachability
track 2 ip sla 2 reachability
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group VPN-HUNRE
key hunre
dns 8.8.8.8
domain hunre
pool IP-VPN
acl 199
max-users 100
crypto ipsec transform-set encrypt-method-1 esp-3des esp-sha-hmac
mode tunnel
crypto dynamic-map DYNMAP 1
set transform-set encrypt-method-1
crypto map VPN client configuration address respond
crypto map VPN 65535 ipsec-isakmp dynamic DYNMAP
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 192.168.1.1 255.255.255.0
ip mtu 1492
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1412
duplex auto
speed auto
interface GigabitEthernet0/1
description FPT
no ip address
ip tcp adjust-mss 1412
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
interface GigabitEthernet0/2
description Connect to CMC
no ip address
ip mtu 1442
ip nat outside
ip virtual-reassembly in
ip tcp adjust-mss 1412
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 2
no cdp enable
interface Dialer1
ip address negotiated
ip mtu 1452
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname [USERNAME]
ppp chap password 0 [PASSWORD]
ppp pap sent-username [USERNAME] password 0 [PASSWORD]
ppp ipcp dns request
crypto map VPN
interface Dialer2
description Logical ADSL Interface 2
ip address negotiated
ip mtu 1442
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1344
dialer pool 2
dialer-group 2
ppp authentication chap pap callin
ppp chap hostname [USERNAME]
ppp chap password 0 [PASSWORD]
ppp pap sent-username [USERNAME] password 0 [PASSWORD]
ppp ipcp address accept
no cdp enable
ip local pool IP-VPN 10.252.252.2 10.252.252.245
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip nat inside source list 10 interface Dialer1 overload
ip nat inside source list 11 interface Dialer2 overload
ip nat inside source static 10.159.217.10 interface Dialer1
ip nat inside source list 199 interface Dialer1 overload
ip nat inside source static tcp 10.159.217.10 80 210.245.54.49 80 extendable
ip nat inside source static tcp 10.159.217.10 3389 210.245.54.49 3389 extendable
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 10.159.217.0 255.255.255.0 192.168.1.8
ip sla auto discovery
ip sla responder
dialer-list 1 protocol ip permit
dialer-list 2 protocol ip permit
access-list 10 permit any
access-list 11 permit any
access-list 101 permit icmp any any
access-list 199 permit ip any any
control-plane
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
password cisco
transport input all
line vty 5 15
password cisco
transport input all
scheduler allocate 20000 1000
ntp master
end
However, I cannot ping interfac Dialer 1. I using Cisco vpn client software ver 5.0.07.0290.
Hopeful for your answers !
ThanksHi David Castro,
Thanks for your answer,
I configed following your guide, but it have not worked yet. I saw that I cannot ping IP gateway Internet . I using ADSL Internet and config PPPoE and my router receive IP from ISP. Here show ip int brief :
GigabitEthernet0/0 192.168.1.1 YES NVRAM up up
GigabitEthernet0/1 unassigned YES NVRAM up up
GigabitEthernet0/2 unassigned YES NVRAM up up
Dialer1 210.245.54.49 YES IPCP up up
Dialer2 101.99.7.73 YES IPCP up up
NVI0 192.168.1.1 YES unset up up
Virtual-Access1 unassigned YES unset up up
Virtual-Access2 unassigned YES unset up up
Virtual-Access3 unassigned YES unset up up
But I cannot ping Interface Dialer 1, so may be VPN is does not worked. Do you have some ideal ?
Thanks very much ! -
VPN client connect to CISCO 887 VPN Server bat they stop at router!!
Hi
my scenario is as follows
SERVER1 on lan (192.168.5.2/24)
|
|
CISCO-887 (192.168.5.4) with VPN server
|
|
INTERNET
|
|
VPN Cisco client on xp machine
My connection have public ip address assegned by ISP, after ppp login.
I've just configured (with Cisco Configuration Professional) the ADSL connection and VPN Server (Easy VPN).
All the PC on LAN surf internet and remote PC connect to VPN Cisco server via cisco VPN client.
But all remote PC after connection to Cisco VPN server don't ping SERVER1 in lan and therefore don't see SERVER1 and every other resource in LAN.
They can ping only router!!!
They are configured with Cisco VPN client (V5.0.007) with "Enabled Trasparent Tunnelling" and "IPSec over UDP NAT/PAT".
What is wrong in my attached configuration? (I've alspo tried to bind Virtual-Template1 both to unnambered Dialer0 and to Loopback0 but without luck)
Peraps ACL problem?
Building configuration...
Current configuration : 5019 bytes
! Last configuration change at 05:20:37 UTC Tue Apr 24 2012 by adm
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname gate
boot-start-marker
boot-end-marker
no logging buffered
aaa new-model
aaa authentication login default local
aaa authentication login ciscocp_vpn_xauth_ml_1 local
aaa authentication login ciscocp_vpn_xauth_ml_2 local
aaa authorization exec default local
aaa authorization network ciscocp_vpn_group_ml_1 local
aaa authorization network ciscocp_vpn_group_ml_2 local
aaa session-id common
memory-size iomem 10
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-453216506
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-453216506
revocation-check none
rsakeypair TP-self-signed-453216506
crypto pki certificate chain TP-self-signed-453216506
certificate self-signed 01
quit
ip name-server 212.216.112.222
ip cef
no ipv6 cef
password encryption aes
license udi pid CISCO887VA-K9 sn ********
username adm privilege 15 secret 5 *****************
username user1 secret 5 ******************
controller VDSL 0
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group EXTERNALS
key 6 *********\*******
dns 192.168.5.2
wins 192.168.5.2
domain domain.local
pool SDM_POOL_1
save-password
crypto isakmp profile ciscocp-ike-profile-1
match identity group EXTERNALS
client authentication list ciscocp_vpn_xauth_ml_2
isakmp authorization list ciscocp_vpn_group_ml_2
client configuration address respond
virtual-template 1
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA1 esp-3des esp-sha-hmac
crypto ipsec profile CiscoCP_Profile1
set transform-set ESP-3DES-SHA1
set isakmp-profile ciscocp-ike-profile-1
interface Loopback0
ip address 10.10.10.10 255.255.255.0
interface Ethernet0
no ip address
shutdown
interface ATM0
no ip address
no atm ilmi-keepalive
interface ATM0.1 point-to-point
pvc 8/35
encapsulation aal5snap
protocol ppp dialer
dialer pool-member 1
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface Virtual-Template1 type tunnel
ip unnumbered Dialer0
tunnel mode ipsec ipv4
tunnel protection ipsec profile CiscoCP_Profile1
interface Vlan1
ip address 192.168.5.4 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly in
interface Dialer0
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname ******@*******.****
ppp chap password 0 alicenewag
ppp pap sent-username ******@*******.**** password 0 *********
ip local pool SDM_POOL_1 192.168.5.20 192.168.5.50
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 600 life 86400 requests 10000
ip nat inside source list 1 interface Dialer0 overload
ip route 0.0.0.0 0.0.0.0 Dialer0
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 192.168.5.0 0.0.0.255
access-list 100 remark CCP_ACL Category=4
access-list 100 permit ip 192.168.5.0 0.0.0.255 any
dialer-list 1 protocol ip permit
line con 0
line aux 0
line vty 0 4
transport input all
endHello,
Your pool of VPN addresses is overlapping with the interface vlan1.
Since proxy-arp is disabled on that interface, it will never work
2 solutions
1- Pool uses a different network than 192.168.5
2- Enable ip proxy-arp on interface vlan1
Cheers,
Olivier -
Airport Time capsule behind cisco router download speed
My airport time capsule is connected to the internet in bridge mode via a cisco router.
The cisco router provides a 99Mbps download speed. However, when I " bridge" my time capsule in between (wired) the speed slows down to 9 Mbps.
I have already tried to assign a static DHCP IP to my time capsules MAC address and disabled DMZ for that specific IP address, but am failing to get the speed up to par.
Any suggestions?I have used Time capsule 1.5 year behind a copperjet modem on ADSL, no problems.
Changed provider and am connected by cable with new cisco modem including router.
So the set up looks like:
internet>cisco modem/router>airport time capsule>macbook pro
The cisco modem without airport time capsule is working ok: when logged in speed is 99 Mbps as it should be (wired and wireless)
Connecting cisco router with UTP cable to time capsule and time capsule with UTP to macbook slows down speed to 9 Mbps
(time capsule in bridgemode)
Specs:
Macbook pro OSX yosemite
Airport Time capsule 2TB 2013 (v 7.7.3)
Cisco modem/router:EPC3928 -
hi ! i want to set up r1 and r2 (see below) to get ip address from r3. what do i need to configure on all routers. thanks.
r1---r2--r3Hi,
To configure a Cisco router as a DHCP server:
http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_configuration_guide_chapter09186a00800ca75c.html
To acquire an IP address via DHCP on an Ethernet interface of the router, use the following command in interface configuration mode:
Router(config-if)# ip address dhcp
The question is how are your routers connected (what type of interfaces), and what is the purpose of this topology.
HTH,
Mohammed Mahmoud. -
How do I set up my hp laserjet printer through Cisco router?
I'm using my HP Laserjet 4000TN printer for my entire network. I need to be able to use it with all my computers. So I usually plug it into the modem via Cat5 cord and it grabs an IP address which I add in System Preferences and I'm good to go. However, I recently had to change my network. I now use a DSL modem as basically a dumb hub. Which then goes into a Cisco 800 series router. From there I need to be able to plug my computer into that router and then see it on both of my computers. (What's the point of having a home network if you can't print from it from any computer on the network?)
I was told to assign it a static IP address of 192.168.7.5. However, when I do this on my computer it doesn't seem to be going through to the printer. Whenever I try to print a test page it does not work.
It is grabbing IP address 192.168.7.22. However, when I enter this as the printer on the computer it is also not printing a test page. Very frustrating. I am unsure if this is the perfect forum for this as obviously it's the Cisco router that has changed and therefore it's not really a Mac issue. But I am unsure where else to turn.
Any help would be greatly appreciated.
Thanks!I found the solution. I was using WEP encryption and I needed to be using WPA encryption.
-
I am getting an un expected error message when updating the setting to "extend network". Is there an obvious setting I may be missing? Cisco router being used.
If you are trying to "extend" using wireless only, you may not be aware that Apple designed the "extend" feature as a proprietary setting to only work with other Apple routers.
It is extremely unlikely that this will work with a Cisco router.
If your plans call for connecting the AirPort Express to the Cisco router using a wired Ethernet connection, it should be possible to configure the Express that way. -
Problems connecting to a Open Network via Wi-fi on Cisco Router
Hi everyone, I know I'm new here but I'm in need of your help, so if you can assist please do so as I cannot live without wi-fi and might have to go back to my nokia again if I can't sort this out.
Vodafone finally released the Iphone on their network in Ireland today and I've picked a 3gs up straight away.
At work I have a wi-fi network with a CISCO router (I have no access to the router as only IT do and they won't change anything to satisfy me and my Iphone anyways). This network has no encryption whatsoever and its free to join, you don't need any password or anything. My nokia at the start couldn't connect as it said that the network needed a pre shared key, this isn't true and in the end it was just change a setting to no auth required for it to log into the network and work perfectly.
Today I got to work and the Iphone can't connect to the network, just says it can't join the network. I cannot find anything about authentication on the settings of the phone nor can I work around this at all. I've had a Ipod touch for (the 2nd gen) for over 2 years and I gave up trying to set it up at work because I just couldn't find what was wrong with it, I ended up almost not using it other than when traveling or on the gym.
So first question is there any way I can access the authentication settings for wi-fi connections on the Iphone? Maybe its just a little change that is needed like the nokia.
Has anyone experienced this problem on a open network that they cannot join?
Any other sugestions? Anything really?
Thank you very much for your time guys, I would really really appreciate your help on this.
Regards,
Rod
PS: I've also tried to install the Iphone configuration utility however I don't know how to access the profiles on the phone, anyone can help with this so I can try the profile I've created?
I don't think it is going to work because the options available on the configuration utility are basicly the same available on the Iphone itself.
Anyone has any sugestion on how to solve this problem??? Thanks very much.Sun Mar 28 06:02:24 unknown Preferences[292] <Warning>: wifi handler: (null)
Sun Mar 28 06:02:27 unknown kernel[0] <Debug>: AppleBCMWLAN::setASSOCIATE() [configd]: lowerAuth = AUTHTYPE_OPEN, upperAuth = AUTHTYPE_NONE, key = CIPHER_NONE, flags = 0x0
Sun Mar 28 06:02:27 unknown configd[22] <Error>: WiFi:[//////////////////>: Failed to associate with Internet: 5
Sun Mar 28 06:02:27 unknown kernel[0] <Debug>: AppleBCMWLANJoinManager::join(): No such network: "Internet"
Sun Mar 28 06:02:27 unknown Preferences[292] <Warning>: WiFiManagerAssociationCallback: err(5), err(00000005)
This is what I get on the Iphone configuration utility debug console. I edited out just a couple of numbers in case this is sensitive information the company wouldn't want me to share.
Message was edited by: F-22 -
Setting up an HP printer through a cisco router
A friend has just bought a new ibook converting over from the PC world and is trying to set up his HP Deskjet 9300 printer to work with a cisco router. The printer works when set up directly to his G4 ibook but not through the router. We have set the IP addressess so we are getting the router wlan light to flash but the lan light does not come on. I think the problem may be what we have entered in the info fields but but cannot find any information to set me straight. I will be heading over this evening to try to help him again so if anyone has some info that will help it will be appreciated - Thanks in advance
Printing to a network ethernet printer (which has an IP address) from a Mac running OS 10.3.x
http://www.ifelix.co.uk/tech/3005.html
Maybe you are looking for
-
RFCs not working after Refresh, is this SecureStore issue?
In our landscape we do frequent system refreshes (DB copy). we use to take out RFC table export and then import them back after refresh. every thing was fine till we upgraded to Netweaver 6.0. Now after refresh most of rfc donesn't work (one which ha
-
How can I print to my HP OfficeJet 6500 Wireless Printer from my iPhone 4S which used to work (on prior iPhones) before AirPrint printers were even available? (running Mac Lion OS, all software and HP sw updates are all performed) I don't get it, I r
-
Bwsem to xi through ABAP PROXIES?
hai pals, "SPROXY" transaction in an BWsem server showing error as follow " no connection to integration builder(only local data visible) ".can u help me to solve this error. with cheers rajesh.
-
Adding Chapter Marks makes DVD audio not work
I sent a 65-minute video to Compressor from Final Cut Pro X. In Compressor I used the 'Dolby Digital Professional' and 'MPEG-2 for DVD' settings from the Disc Burning folder as targets, and added a job action to create the DVD. I left all default set
-
When I try and watch Apple keynotes the video and audio playback are jumpy and garbled. Windows & Quicktime are fully up to date. I have tried uninstalling and reinstalling quicktime - no help. I can watch videos in iTunes no problems. My Internet co