Setting Sensitivity Area on WVC54GCA Camera

Inside the web based setup utility, you can custom set the sensitivity area of the camera. I am using the camera from inside my windows to look to an area about 4-6 feet (maybe up to 10-15 feet) away for motion. I am having mixed results. In your experience, is it better to have custom 2-4 window sensitivity, or is it better to use the full screen option? Also, I just want to confirm that moving the slider to the right increases the camera's sensitivity to motion.
Thanks in advance

Thank you very much for the reply. I am not sure I completely understood the answer, so let me clarify what I think you said in my words.
1. Using full screen sensitivity vs. 2-4 Window sensitivity should not make any difference in the camera's ability to detect motion.
2. Your comment about full screen for vision clarity confuses me. Regardless of the sensitivity chosen, would I not see the entire screen? My original thought was that a smaller area for motion detection would make it more likely to actually capture motion since the camera has less surface area to cover.
3. Your comment about multiple camera's is true in my case. I have 2 camera's looking at different places (near each other, though). I am not sure I understand how 2-4 window sensitivity has any impact on one vs. two cameras since you set them both separately. This might point to what may be a fundamental misunderstanding on my part, so I do hope you will explain what you meant!
I appreciate your help

Similar Messages

RTSP steaming Port Forward (?) problems with 4 (four) WVC54GCA cameras on WRT54G v2 router.

I am having difficulties correctly setting up my four (4) WVC54GCA cameras on a WRT54G v2 router to make them stream RTSP videos that I can view on my BlackBerry Bold. I can access the cameras from the internet, through
http://CAM1_SubDomain.Linksys-Cam.com/1024
http://CAM2_SubDomain.Linksys-Cam.com/1025
http://CAM3_SubDomain.Linksys-Cam.com/1026
http://CAM4_SubDomain.Linksys-Cam.com/1027
so that part works fine.
All the 4 cameras are set up with static IP addresses.
The default RTSP port 554 and RTP Data port at 5000 are forwarded to CAM1 IP address. I can access CAM1 RTSP feed on my Blackberry Bold (and also on a good old Samsung SGH-A706 cell phone).
CAM 1 Settings:
STATIC IP: 192.168.1.201
Alternate HTTP Port: 1024 à Forwarded to 192.168.1.201
RTSP Port: 554 à Forwarded to 192.168.1.201
RTSP Data Port: 5000 à Forwarded to 192.168.1.201
RTSP access on cell phone WORKS only with the following format: rtsp://CAM1_SubDomain.Linksys-Cam.com/1111, where 1111 is the access code.
CAM 2 Settings:
STATIC IP: 192.168.1.202
Alternate HTTP Port: 1025 à Forwarded to 192.168.1.202
RTSP Port: 1029 à Forwarded to 192.168.1.202
RTSP Data Port: NOT SURE IF I NEED TO FORWARD ONE, HELP PLEASE
Despite I have a dedicated subdomain for each camera from TZO, the following link DOESN’T WORK
rtsp://CAM2_SubDomain.Linksys-Cam.com/1111, where 1111 is the access code.
Actually, when I enter the above link, the cellphone brings in the feed from CAM1, I guess due to the identical access code with CAM2. Once I change the access code for CAM2, it doesn’t’t show any feed.
CAM 3 Settings:
STATIC IP: 192.168.1.203
Alternate HTTP Port: 1026 à Forwarded to 192.168.1.203
RTSP Port: 1030 à Forwarded to 192.168.1.203
RTSP Data Port: NOT SURE IF I NEED TO FORWARD ONE HELP PLESE
Despite I have a dedicated subdomain for each camera from TZO, the following link DOESN’T WORK
rtsp://CAM3_SubDomain.Linksys-Cam.com/1111, where 1111 is the access code. This feed also brings in CAM1.
CAM 4 Settings:
STATIC IP: 192.168.1.204
Alternate HTTP Port: 1027 à Forwarded to 192.168.1.204
RTSP Port: 1031 à Forwarded to 192.168.1.203
RTSP Data Port: NOT SURE IF I NEED TO FORWARD ONE HELP PLEASE
Despite I have a dedicated subdomain for each camera from TZO, the following link DOESN’T WORK
rtsp://CAM4_SubDomain.Linksys-Cam.com/1111, where 1111 is the access code. This feed also brings in CAM1
DMZ could probably fix the problem for a second camera, but not for all four CAMs
OS: XP SP2
Question 1: Any idea how can I get all the four cameras RTSP feed on my cell/BlackBerry?
Question 2: I am running out of Port Range forwards. Should I add more port forwards, I have only one more shot. Any workaround?
Each and every help idea is greatly appreciated!

I have six of these cams and used the tutorial and review at http://www.Myhomserver.com for help. First thing, set ALL the RTSP access codes the SAME, so all you need to do is increment the port for each cam
Cam 1 - 192.168.1.200 - set at port 80 TCP - RTSP port default at 554, forward port 5000 UDP/TCP and the RTSP access code 12345
Cam 2 - 192.168.1.201 - set at port 1024 TCP - RTSP port at 1029, forward port 5001 UDP/TCP and the RTSP access code 12345
Cam 3 - 192.168.1.202 - set at port 1025 TCP - RTSP port at 1030, forward port 5002 UDP/TCP and the RTSP access code 12345
Cam 4 - 192.168.1.203 - set at port 1026 TCP - RTSP port at 1031, forward port 5003 UDP/TCP and the RTSP access code 12345
Cam 5 - 192.168.1.204 - set at port 1027 TCP - RTSP port at 1032, forward port 5004 UDP/TCP and the RTSP access code 12345
Cam 6 - 192.168.1.205 - set at port 1028 TCP - RTSP port at 1033, forward port 5005 UDP/TCP and the RTSP access code 12345
This worked for me using the above settings....take your time, plan out the ports, all RTSP ports must be different on each cam
Accessing CAMS can be done via your cell phone below:
Camera 1---> RTSP://<your TZO camera domain>:554/12345
Camera 2---> RTSP://<your TZO camera domain>:1029/12345
Camera 3---> RTSP://<your TZO camera domain>:1030/12345
Camera 4---> RTSP://<your TZO camera domain>:1031/12345
Camera 5---> RTSP://<your TZO camera domain>:1032/12345
Camera 6---> RTSP://<your TZO camera domain>:1033/12345
http://www.MyHomeServer.com
Linksys IP camera reviews, Tutorials and How-To's on Web & Mobile Streaming

Time Capsule and Linksys WVC54GCA Camera needs tweaked.

I replaced my Linksys wireless router with Time Capsule. Trying to get my WVC54GCA camera back online. I am hard wired from cable modem in basement to Time Capsule which I located in living room then cable back to switch in basement for distribution to network. Using the camera on ethernet cable I can get it to work fine when attached to the switch but not when attached directly to a port on the TC. I run 2 Macs, a PC and Direct TV DVR wired and wireless for Macbook Pro. Everything works fine other than being able to locate the camera where I want it. What setting am I missing? I set the port forwarding and can get in fine via DYNDNS as before.

Good thoughts. I am using a Netgear Gigabit 8 port auto-sensing switch and it must be sorting things out. The TC is the final piece to making my home network totally gigabit. At this point I think I will pull another ethernet cable from the switch to the area I want to locate the camera.

Why can't I update any apps? When I hit update it gives me an old id. But in settings my new id is totally set and verified. How cam I make the change in App Store?

Why can't I update any apps? When I hit update it gives me an old id. But in settings my new id is totally set and verified. How cam I make the change in App Store?

App purchases are permanently tied to the ID with which they were purchased. They cannot be transferred to a new ID.
You will have to enter the password for that ID or delete the apps and re-purchase them with the new one.
~Lyssa

WVC54GCA camera, no wireless network found

I just purchased a WVC54GCA camera and I am having problems getting it set up. I have the power plugged in, and the network cable plugged directly into my router, (the solid blue light is on), but when I get to step 2 in the Setup Wizard, no wireless network is found. I know I have a wireless network running, because I have another PC connected, and that PC is also able to find my neighbors wireless network.
The routher is a SMCWBR14-G2 EU Barricade™ g Wireless Broadband Router set up in 11b/g mixed mode.
Has anyone solved this problem? Right now I only see one solution - to return it to the shop where I bought it, but I would like to have the camera working in the wireless mode.
Arne

I've just been working on the same problem for the past 4 hours...
I tried so many things, but finally found something that seemed to work.
Forget about the Linksys set up software. You'll have to work with your web browser to access your modem/network settings and your camera settings. Just manually enter the information into the linksys BASIC SETUP section (SSID, etc). I chose a fixed IP address and set that up with my modem settings too.
If you can set your camera up manually, ie. through the default http://192.168.1.115 or whatever yours is set at, then pull up your modem/router settings page (mine is a 2wire - http://192.168...etc)
Find the "device details" for your camera. Copy the hardware address. Something like
00:21:29:7f:6c:c2
Under the wireless settings for your home network, try to find something that says "MAC filtering" or something similar. ENABLE this, if it is not already and see if you can ADD the camera's hardware address to the list of allowed devices.
After doing this, and powering off and on my camera - Hey Presto! It was working. Don't even know why I tried this - I guess I'd tried everything else and it looked like a good idea...
Hope it works for you too. I'd love to think that all these hours of my trying to find a solution pays off for someone else!

How can I transfer photos from my comp to my ipad2.I have the connection kit and can transfer photos that are direct from camera BUT if I transfer photos from comp to card it will not recognize them ????

how can I transfer photos from my comp to my ipad2.I have the connection kit and can transfer photos that are direct from camera BUT if I transfer photos from comp to card it will not recognize them ????

To sync photos from a Mac or Windows PC to your device using photo applications
Make sure you have the latest version of iTunes installed.
In iTunes, select your device's icon in the Devices list on the left.
Click the Photos tab.
Choose "Sync photos from."
On a Mac, choose iPhoto or Aperture from the pop-up menu.
On a Windows PC, choose Photoshop Album or Photoshop Elements from the pop-up menu.
Note: Some versions of Photoshop Album and Photoshop Elements don't support collections. You can still use them to sync all your photos.
If you want to sync all your photos, enable the option for "All photos, albums, events, and faces." If you want to sync photos from only some albums, events, or faces, enable the option for "Selected albums, events, and faces" and then select the albums you want. If syncing on a Mac with iPhoto version 6.0.6 or later, you may enable the option to "Include videos" to sync videos directly from iPhoto to your device. (Requires iOS 3.0 or later).
Click Apply.
To sync photos from a folder on your hard disk to your device
Drag the images you want into a folder on your computer. If you want images to appear in separate photo albums on your device, create folders inside the main folder and drag images into the new folders.
In iTunes, select the device icon in the Devices list on the left.
Choose "Sync photos from."
Select Choose Folder from the pop-up menu and choose your main image folder.
Click Apply.

Hi I shoot on a canon 5d mk11 and I record my audio on an external device yet when I open up my footage in final cut pro x I can't find my external audio files only the ones attached to the clip which are off the camera mic

I shoot on a canon 5d mk11 and I record my audio on an external device yet when I open up my footage in final cut pro x I can't find my external audio files only the ones attached to the clip which are off the camera mic

What device?
What format?
How are you importing it?
Can you find the external audio with Finder?
Where is your destination file when you import it?
Andy

How can i send videoes which are not in camera roll via whatss app to others ?

hi,
I am going to know that how can i transfer video which are not in camera roll via whatss app to others ?
thnaks in advanced.

Where are the videos?
If WhatsApp supports sending videos from the Camera Roll only and that is your only option, that is it.
Contact WhatsApp. They have a website.

TS3989 My photos on my iPhone 4 are on my camera roll and in my photo stream, but my recent photos have not moved to my photo stream folder on my computer (windows 7). What can I do?

My photos on my iPhone 4 are on my camera roll and in my photo stream, but my recent photos have not moved to my photo stream folder on my computer (windows 7). What can I do?

At 1.3GB available, your storage space is getting very thin no matter what you do further. As long as you have the photo's in the camera roll saved on your computer you can delete them. Just make sure first that they are in your photo software. If updating in iTunes, just backup/sync first, then update, and that will save the camera roll in the backup as well.
At only 1.3GB you eventually are going to find yourself unable to install or update some app, or unable to take any new pictures, or some other limitation that will force you to free up space anyway. So now, before updating, sounds like a good time to make sure everything is backed up or stored somewhere else, and clean house a bit, then update.

What setting changes are to be made??

I am adding some .c files to my MAC application(cocoa), I am getting a lot of errors while compiling those files.
What setting changes are to be made before adding C files to MAC OS project???
If so can anyone point out that...??
1. I am getting errors with the #include statements in my files...
2. expected '=', ',', ';', 'asm' or '__attribute__' before 'asn_DEF_Payload'
How can I get around these list of errors??
Thanks in advance.

Sun Java Enterprise System Support Forum and the Directory Server's "Release Notes" [See docs.sun.com] is a good place to find this information. Also upgrade to the latest DS5.2 Patch 4.
One probable cause could be that either the BindDN or the SearchBase used by your application no longer exists in the upgraded server's setup. Please check the access log on the Directory server to pinpoint the culprit. The corresponding entry will have "err=32".
Examples:
SRCH base="dc=abc,dc=example,dc=com" ....
RESULT err=32 tag=101 nentries=0 etime=0
[Note: Tag 101 means the search base does not exist]
BIND dn="cn=user,dc=abc,dc=example,dc=com" ....
RESULT err=32 tag=97 nentries=0 etime=0
[Note: Tag 97 means BindDN does not exist]
Based on your requirements, you will either have to add the missing entry or upgrade your applications' configuration to use an alternative entry.
For more on Access Log contents see
http://docs.sun.com/source/817-7616/fileref.html#wp20452

TS3899 After upgrading to IOS 7, the only options Gmail gives using Safari or mail to attach files are attaching a camera roll file or draw a scribble. How can I attach a PDF or word doc? I was able to do so using IOS 6.

After upgrading to IOS 7, the only options Gmail gives using Safari or Mail app to attach a file are attaching a camera roll file or drawing a scribble. How can I attach a document such as a PDF or word file? I used to be able to do so using IOS 6.

skinb wrote:
Did you solve the problem? I am a new iphone user. Mac is less intuitive than wished.
You posted in the iPad forum instead of the iPhone forum. To get answers to your question, post in the proper forum. See https://discussions.apple.com/welcome
You tagged onto an older post. If you want an answer to your specific question, you need to create a new post. By creating a new post, you will receive emails when helpers post responses.
 Cheers, Tom

I listen to a lot of live performances (house sets that are from 1 hour to 3 hours long) when I start to listen to a set and then stop to do something else on the iPhone when I go back to start to listen to the track it has started from the beginning.

I listen to a lot of live performances (house sets that are from 1 hour to 3 hours long) when I start to listen to a set and then stop to do something else on the iPhone when I go back to start to listen to the track it has started from the beginning.

It sounds like either your hard drive or the SATA cable that connects it to the motherboard are failing. This could be heat related in your case, which is why you see it after it runs awhile. You can take it to the Genius Bar for a free evaluation. If you decide to test it yourself, I usually suggest moving the hard drive to an external enclosure. If it works there for awhile, the cable is probably the issue.
http://www.amazon.com/Sabrent-2-5-Inch-Aluminum-Enclosure-EC-TB4P/dp/B005EIGUD4/ ref=sr_1_3?ie=UTF8&qid=1397647657&sr=8-3&keywords=2.5+enclosure
http://www.ifixit.com/Device/MacBook_Pro_13%22_Unibody_Mid_2009

SQ01 (How to set Global Area as default)

Hi All
In SQ01, i find 2 environments in Query Areas - Global Area & Standard Area. Everytime i execute SQ01 transaction, it takes me to Standard Area, then i have to change it to Global Area & then select the user group. I would like to know how i can set Global Area as default & also a particular user group, so that everytime i run SQ01, it directly takes me to Global Area & the particular user group, so i can execute my query directly instead of having to change it each time.
Hope my problem is clear, await inputs.
Vivek

Hello Vivek,
You need to maintian some default parameters in your User master record.
Parameter ID :
AQB for User Group
AQW for Query Area.
Select the AQB from the drop-down and give your default user group in the parameter value.
Regards,
Naimesh Patel

IW31 how to set functional area as a default value?

Dear all:
Can anyone guide me, is any way to set "functional area" as a default value (t-code iw31 Additional Data -> Functional area)?
Thanks in advance.

Hello ,
The standard funtionality is set to default the Functional Area from the Order Type. I believe it is possible to change the default value for the Functional Area in Transaction KOT2. The PM order types should be selectable in this transaction.
I hope this information has been helpful.
Best Regards,
Frank

Has anyone else found that Sony XAVC 4K files are flagged as camera files in Import?

Has anyone else found that Sony XAVC 4K files are flagged as camera files in Import?
It sems that because they are being seen as a camera it is not possible to leave them in place on import?
I have already backed up the camera files onto Thunderbolt drives and therefore I don't want them to be moved again!!
Can I force FCPX to see the Ext HDD as a volume not a Camera?
Thank you
Jules

Hi Tom
Thank you for your reply,
Surely all files originated from a camera? If I back them up to an external drive and clone them onto another drive for editing with FCPX, I don't expect them to be seen as camera files which FCPX then copies again just so that I can edit them. I just want to leave them in place, but FCPX doesn't give me that option.
It seems that FCPX has failed at the first hurdle. It is forcing me to have to buy extra storage just so that FCPX can copy them on import. Surely, if FCPX can handle them natively then why does it have to move them?
Jules

Setting Sensitivity Area on WVC54GCA Camera

Similar Messages

Maybe you are looking for