Setting special baudrates in NI-CAN
Hello,
I am trying to set baudrate of 307.690 bauds in NI-CAN.
I read it should be possible to set non-standard baudrates:
http://digital.ni.com/public.nsf/allkb/CBA1FC627FFA0F8F862564DC0071B3A7
But I am unable to figure out the computation formula between decimal and hexadecimal (BTR0 & BTR1) values for non-standards baudrate ?
I am unable to compute the values for BTR0 and BTR1 to have a baudrate near to 307.690 bauds.
You think that baudrates no included in the table in the link above, are accepted by the card ? Because if in NI-MAX I set some extrapolated values for BTR0 and BTR1 (advanced settings), they are rounded to the nearest standard values.
If not, they are accepted by ncSetAttr.vi but I am not sure the chipset will use effectively this baudrate (I am in a pre-study phase).
Cheers,
Ben
Solved!
Go to Solution.
Seube wrote:
nathand: Thanks a lot.
For my part, I get BTR0=0x01 and BTR1=0x19 for a sampling rate of 84.6%, while your values get 76.9%
I suppose I have to retain the values with the biggest sample point.
Our differences can be explained by hardware differences : I have a PCI NI-CAN card.
Actually, if you look at the link you provided, it says the BTR values are the same regardless of which CAN card you are using. Either set of those values is likely to work (yours, or the ones I posted); a sampling point around 80% is reasonable. The % value is not the sampling RATE, it is the sampling POINT. It is the point during the transmission of a bit at which the value on the wire is actually sampled to determine if it's a 1 or a 0. You don't necessarily want the maximum value (a sample point at 95% would not be ideal) because if you're too close to the end of the time period and the oscillators are not perfectly synchronized, you may read the wrong value.
Similar Messages
-
How to set special payment advise form for payment advise.
Hello,
i would like to set special sap script form payment advise for particular payment method (not only for company code) but print program calls every time only one payment advise form from tcode OBZ1 - table T042B (not from OBZ4 - table T042E).
Can be payment advise form dependent on payment method?
Is it possible at all.
thanksOK
-
I created a slide show in imovie for my daughters 21st with voice overs from friends and family which was all working fine but now the voice recordings are not playing at all. Obviously some setting has changed but I can't find which one.
I created a slide show in imovie for my daughters 21st with voice overs from friends and family which was all working fine but now the voice recordings are not playing at all. Obviously some setting has changed but I can't find which one.
-
RMAN duplicate target using set until telling me it can not find data files
I have RMAN scripts that I use freqently to clone a database from DB (production) to another (non-prod). These work just fine. I use the set until so that I can tell it at what point I want the new DB to be created from the backups of the source.
I had a request to go back a few weeks and the backup files (I do compressed backups to disk) were on tape. I had my backup person restore my backup directory for the source DB as it looked on a certain day (May 28). I have an 8 day retention policy and so the backup files that were restored showed files all the way back to 5/20 ( includes the point I want to use in my set until clause).
However, whenever I try to execute the rman clone, it tells me for each datafile:
RMAN-06023: no backup or copy of datafile 1 found to restore
Like I said, I am able to do this for a current backup that is on disk. I moved the backup files to the source db server and it works fine. However, from these files restored from tape it errors.
Here is the RMAN script:
spool log to c:\temp\clone_CSPROD_CSPRSUM1.log;
#connect to catalog <catalog info>
# target is the source and auxiliary is destination
#connect target <put in source info here>
#connect auxiliary /
run {
allocate auxiliary channel d1 type disk format 'F:\backups\CSPROD\d1\CSPROD_DATA_%s';
allocate auxiliary channel d2 type disk format 'F:\backups\CSPROD\d2\CSPROD_DATA_%s';
allocate auxiliary channel d3 type disk format 'F:\backups\CSPROD\d3\CSPROD_DATA_%s';
allocate auxiliary channel d4 type disk format 'F:\backups\CSPROD\d4\CSPROD_DATA_%s';
allocate auxiliary channel a1 type disk format 'F:\backups\CSPROD\a1\CSPROD_arch_%s';
##Archivelog number get from sql archive log list command
#set until sequence 831;
set until time "to_date('2011-05-25 08:00:00', 'YYYY-MM-DD HH24:MI:SS')";
duplicate target database to CSPRSUM1 nofilenamecheck
logfile
group 1('+DATA/CSPRSUM1/onlinelog/redo1a.log', '+FRA/CSPRSUM1/onlinelog/redo1b.log') size 50m,
group 2('+DATA/CSPRSUM1/onlinelog/redo2a.log', '+FRA/CSPRSUM1/onlinelog/redo2b.log') size 50m,
group 3('+DATA/CSPRSUM1/onlinelog/redo3a.log', '+FRA/CSPRSUM1/onlinelog/redo3b.log') size 50m;
Exit
Here is the output:
Spooling started in log file: c:\temp\clone_CSPROD_CSPRSUM1.log
Recovery Manager11.1.0.7.0
RMAN> #connect catalog <redacted info>>
2> # target is the source and auxiliary is destination
3> #connect target <redacted info>
4> #connect auxiliary /
5>
6> run {
7> allocate auxiliary channel d1 type disk format 'F:\backups\CSPROD\d1\CSPROD_DATA_%s';
8> allocate auxiliary channel d2 type disk format 'F:\backups\CSPROD\d2\CSPROD_DATA_%s';
9> allocate auxiliary channel d3 type disk format 'F:\backups\CSPROD\d3\CSPROD_DATA_%s';
10> allocate auxiliary channel d4 type disk format 'F:\backups\CSPROD\d4\CSPROD_DATA_%s';
11> allocate auxiliary channel a1 type disk format 'F:\backups\CSPROD\a1\CSPROD_arch_%s';
12> ##Archivelog number get from sql archive log list command
13> #set until sequence 831;
14> set until time "to_date('2011-05-25 08:00:00', 'YYYY-MM-DD HH24:MI:SS')";
15> duplicate target database to CSPRSUM1 nofilenamecheck
16> logfile
17> group 1('+DATA/CSPRSUM1/onlinelog/redo1a.log', '+FRA/CSPRSUM1/onlinelog/redo1b.log') size 50m,
18> group 2('+DATA/CSPRSUM1/onlinelog/redo2a.log', '+FRA/CSPRSUM1/onlinelog/redo2b.log') size 50m,
19> group 3('+DATA/CSPRSUM1/onlinelog/redo3a.log', '+FRA/CSPRSUM1/onlinelog/redo3b.log') size 50m;
20> }
starting full resync of recovery catalog
full resync complete
allocated channel: d1
channel d1: SID=534 device type=DISK
allocated channel: d2
channel d2: SID=533 device type=DISK
allocated channel: d3
channel d3: SID=532 device type=DISK
allocated channel: d4
channel d4: SID=531 device type=DISK
allocated channel: a1
channel a1: SID=530 device type=DISK
executing command: SET until clause
Starting Duplicate Db at 15-JUN-11
RMAN-05529: WARNING: DB_FILE_NAME_CONVERT resulted in invalid ASM names; names changed to disk group only.
contents of Memory Script:
set until scn 260398799;
set newname for datafile 1 to
"+data";
set newname for datafile 2 to
"+data";
set newname for datafile 3 to
"+data";
set newname for datafile 4 to
"+data";
set newname for datafile 5 to
"+data";
set newname for datafile 6 to
"+data";
set newname for datafile 7 to
"+data";
set newname for datafile 8 to
"+data";
set newname for datafile 9 to
"+data";
set newname for datafile 10 to
"+data";
set newname for datafile 11 to
"+data";
set newname for datafile 12 to
"+data";
set newname for datafile 13 to
"+data";
set newname for datafile 14 to
"+data";
set newname for datafile 15 to
"+data";
set newname for datafile 16 to
"+data";
set newname for datafile 17 to
"+data";
set newname for datafile 18 to
"+data";
set newname for datafile 19 to
"+data";
set newname for datafile 20 to
"+data";
set newname for datafile 21 to
"+data";
set newname for datafile 22 to
"+data";
set newname for datafile 23 to
"+data";
set newname for datafile 24 to
"+data";
set newname for datafile 25 to
"+data";
set newname for datafile 26 to
"+data";
set newname for datafile 27 to
"+data";
set newname for datafile 28 to
"+data";
set newname for datafile 29 to
"+data";
set newname for datafile 30 to
"+data";
set newname for datafile 31 to
"+data";
set newname for datafile 32 to
"+data";
set newname for datafile 33 to
"+data";
set newname for datafile 34 to
"+data";
set newname for datafile 35 to
"+data";
set newname for datafile 36 to
"+data";
set newname for datafile 37 to
"+data";
set newname for datafile 38 to
"+data";
set newname for datafile 39 to
"+data";
set newname for datafile 40 to
"+data";
set newname for datafile 41 to
"+data";
set newname for datafile 42 to
"+data";
set newname for datafile 43 to
"+data";
set newname for datafile 44 to
"+data";
set newname for datafile 45 to
"+data";
set newname for datafile 46 to
"+data";
set newname for datafile 47 to
"+data";
set newname for datafile 48 to
"+data";
set newname for datafile 49 to
"+data";
set newname for datafile 50 to
"+data";
set newname for datafile 51 to
"+data";
set newname for datafile 52 to
"+data";
set newname for datafile 53 to
"+data";
set newname for datafile 54 to
"+data";
set newname for datafile 55 to
"+data";
set newname for datafile 56 to
"+data";
set newname for datafile 57 to
"+data";
set newname for datafile 58 to
"+data";
set newname for datafile 59 to
"+data";
set newname for datafile 60 to
"+data";
set newname for datafile 61 to
"+data";
set newname for datafile 62 to
"+data";
set newname for datafile 63 to
"+data";
set newname for datafile 64 to
"+data";
set newname for datafile 65 to
"+data";
set newname for datafile 66 to
"+data";
set newname for datafile 67 to
"+data";
set newname for datafile 68 to
"+data";
set newname for datafile 69 to
"+data";
set newname for datafile 70 to
"+data";
set newname for datafile 71 to
"+data";
set newname for datafile 72 to
"+data";
set newname for datafile 73 to
"+data";
set newname for datafile 74 to
"+data";
set newname for datafile 75 to
"+data";
set newname for datafile 76 to
"+data";
set newname for datafile 77 to
"+data";
set newname for datafile 78 to
"+data";
set newname for datafile 79 to
"+data";
set newname for datafile 80 to
"+data";
set newname for datafile 81 to
"+data";
set newname for datafile 82 to
"+data";
set newname for datafile 83 to
"+data";
set newname for datafile 84 to
"+data";
set newname for datafile 85 to
"+data";
set newname for datafile 86 to
"+data";
set newname for datafile 87 to
"+data";
set newname for datafile 88 to
"+data";
set newname for datafile 89 to
"+data";
set newname for datafile 90 to
"+data";
set newname for datafile 91 to
"+data";
set newname for datafile 92 to
"+data";
set newname for datafile 93 to
"+data";
set newname for datafile 94 to
"+data";
set newname for datafile 95 to
"+data";
set newname for datafile 96 to
"+data";
set newname for datafile 97 to
"+data";
set newname for datafile 98 to
"+data";
set newname for datafile 99 to
"+data";
set newname for datafile 100 to
"+data";
set newname for datafile 101 to
"+data";
set newname for datafile 102 to
"+data";
set newname for datafile 103 to
"+data";
set newname for datafile 104 to
"+data";
set newname for datafile 105 to
"+data";
set newname for datafile 106 to
"+data";
set newname for datafile 107 to
"+data";
set newname for datafile 108 to
"+data";
set newname for datafile 109 to
"+data";
set newname for datafile 110 to
"+data";
set newname for datafile 111 to
"+data";
set newname for datafile 112 to
"+data";
set newname for datafile 113 to
"+data";
set newname for datafile 114 to
"+data";
set newname for datafile 115 to
"+data";
set newname for datafile 116 to
"+data";
set newname for datafile 117 to
"+data";
set newname for datafile 118 to
"+data";
set newname for datafile 119 to
"+data";
set newname for datafile 120 to
"+data";
set newname for datafile 121 to
"+data";
set newname for datafile 122 to
"+data";
restore
clone database
executing Memory Script
executing command: SET until clause
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
Starting restore at 15-JUN-11
released channel: d1
released channel: d2
released channel: d3
released channel: d4
released channel: a1
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03002: failure of Duplicate Db command at 06/15/2011 11:21:42
RMAN-01005: not all datafiles have backups that can be recovered to scn 260398799
RMAN-03015: error occurred in stored script Memory Script
RMAN-06026: some targets not found - aborting restore
RMAN-06023: no backup or copy of datafile 122 found to restore
RMAN-06023: no backup or copy of datafile 121 found to restore
RMAN-06023: no backup or copy of datafile 120 found to restore
RMAN-06023: no backup or copy of datafile 119 found to restore
RMAN-06023: no backup or copy of datafile 118 found to restore
RMAN-06023: no backup or copy of datafile 117 found to restore
RMAN-06023: no backup or copy of datafile 116 found to restore
RMAN-06023: no backup or copy of datafile 115 found to restore
RMAN-06023: no backup or copy of datafile 114 found to restore
RMAN-06023: no backup or copy of datafile 113 found to restore
RMAN-06023: no backup or copy of datafile 112 found to restore
RMAN-06023: no backup or copy of datafile 111 found to restore
RMAN-06023: no backup or copy of datafile 110 found to restore
RMAN-06023: no backup or copy of datafile 109 found to restore
RMAN-06023: no backup or copy of datafile 108 found to restore
RMAN-06023: no backup or copy of datafile 107 found to restore
RMAN-06023: no backup or copy of datafile 106 found to restore
RMAN-06023: no backup or copy of datafile 105 found to restore
RMAN-06023: no backup or copy of datafile 104 found to restore
RMAN-06023: no backup or copy of datafile 103 found to restore
RMAN-06023: no backup or copy of datafile 102 found to restore
RMAN-06023: no backup or copy of datafile 101 found to restore
RMAN-06023: no backup or copy of datafile 100 found to restore
RMAN-06023: no backup or copy of datafile 99 found to restore
RMAN-06023: no backup or copy of datafile 98 found to restore
RMAN-06023: no backup or copy of datafile 97 found to restore
RMAN-06023: no backup or copy of datafile 96 found to restore
RMAN-06023: no backup or copy of datafile 95 found to restore
RMAN-06023: no backup or copy of datafile 94 found to restore
RMAN-06023: no backup or copy of datafile 93 found to restore
RMAN-06023: no backup or copy of datafile 92 found to restore
RMAN-06023: no backup or copy of datafile 91 found to restore
RMAN-06023: no backup or copy of datafile 90 found to restore
RMAN-06023: no backup or copy of datafile 89 found to restore
RMAN-06023: no backup or copy of datafile 88 found to restore
RMAN-06023: no backup or copy of datafile 87 found to restore
RMAN-06023: no backup or copy of datafile 86 found to restore
RMAN-06023: no backup or copy of datafile 85 found to restore
RMAN-06023: no backup or copy of datafile 84 found to restore
RMAN-06023: no backup or copy of datafile 83 found to restore
RMAN-06023: no backup or copy of datafile 82 found to restore
RMAN-06023: no backup or copy of datafile 81 found to restore
RMAN-06023: no backup or copy of datafile 80 found to restore
RMAN-06023: no backup or copy of datafile 79 found to restore
RMAN-06023: no backup or copy of datafile 78 found to restore
RMAN-06023: no backup or copy of datafile 77 found to restore
RMAN-06023: no backup or copy of datafile 76 found to restore
RMAN-06023: no backup or copy of datafile 75 found to restore
RMAN-06023: no backup or copy of datafile 74 found to restore
RMAN-06023: no backup or copy of datafile 73 found to restore
RMAN-06023: no backup or copy of datafile 72 found to restore
RMAN-06023: no backup or copy of datafile 71 found to restore
RMAN-06023: no backup or copy of datafile 70 found to restore
RMAN-06023: no backup or copy of datafile 69 found to restore
RMAN-06023: no backup or copy of datafile 68 found to restore
RMAN-06023: no backup or copy of datafile 67 found to restore
RMAN-06023: no backup or copy of datafile 66 found to restore
RMAN-06023: no backup or copy of datafile 65 found to restore
RMAN-06023: no backup or copy of datafile 64 found to restore
RMAN-06023: no backup or copy of datafile 63 found to restore
RMAN-06023: no backup or copy of datafile 62 found to restore
RMAN-06023: no backup or copy of datafile 61 found to restore
RMAN-06023: no backup or copy of datafile 60 found to restore
RMAN-06023: no backup or copy of datafile 59 found to restore
RMAN-06023: no backup or copy of datafile 58 found to restore
RMAN-06023: no backup or copy of datafile 57 found to restore
RMAN-06023: no backup or copy of datafile 56 found to restore
RMAN-06023: no backup or copy of datafile 55 found to restore
RMAN-06023: no backup or copy of datafile 54 found to restore
RMAN-06023: no backup or copy of datafile 53 found to restore
RMAN-06023: no backup or copy of datafile 52 found to restore
RMAN-06023: no backup or copy of datafile 51 found to restore
RMAN-06023: no backup or copy of datafile 50 found to restore
RMAN-06023: no backup or copy of datafile 49 found to restore
RMAN-06023: no backup or copy of datafile 48 found to restore
RMAN-06023: no backup or copy of datafile 47 found to restore
RMAN-06023: no backup or copy of datafile 46 found to restore
RMAN-06023: no backup or copy of datafile 45 found to restore
RMAN-06023: no backup or copy of datafile 44 found to restore
RMAN-06023: no backup or copy of datafile 43 found to restore
RMAN-06023: no backup or copy of datafile 42 found to restore
RMAN-06023: no backup or copy of datafile 41 found to restore
RMAN-06023: no backup or copy of datafile 40 found to restore
RMAN-06023: no backup or copy of datafile 39 found to restore
RMAN-06023: no backup or copy of datafile 38 found to restore
RMAN-06023: no backup or copy of datafile 37 found to restore
RMAN-06023: no backup or copy of datafile 36 found to restore
RMAN-06023: no backup or copy of datafile 35 found to restore
RMAN-06023: no backup or copy of datafile 34 found to restore
RMAN-06023: no backup or copy of datafile 33 found to restore
RMAN-06023: no backup or copy of datafile 32 found to restore
RMAN-06023: no backup or copy of datafile 31 found to restore
RMAN-06023: no backup or copy of datafile 30 found to restore
RMAN-06023: no backup or copy of datafile 29 found to restore
RMAN-06023: no backup or copy of datafile 28 found to restore
RMAN-06023: no backup or copy of datafile 27 found to restore
RMAN-06023: no backup or copy of datafile 26 found to restore
RMAN-06023: no backup or copy of datafile 25 found to restore
RMAN-06023: no backup or copy of datafile 24 found to restore
RMAN-06023: no backup or copy of datafile 23 found to restore
RMAN-06023: no backup or copy of datafile 22 found to restore
RMAN-06023: no backup or copy of datafile 21 found to restore
RMAN-06023: no backup or copy of datafile 20 found to restore
RMAN-06023: no backup or copy of datafile 19 found to restore
RMAN-06023: no backup or copy of datafile 18 found to restore
RMAN-06023: no backup or copy of datafile 17 found to restore
RMAN-06023: no backup or copy of datafile 16 found to restore
RMAN-06023: no backup or copy of datafile 15 found to restore
RMAN-06023: no backup or copy of datafile 14 found to restore
RMAN-06023: no backup or copy of datafile 13 found to restore
RMAN-06023: no backup or copy of datafile 12 found to restore
RMAN-06023: no backup or copy of datafile 11 found to restore
RMAN-06023: no backup or copy of datafile 10 found to restore
RMAN-06023: no backup or copy of datafile 9 found to restore
RMAN-06023: no backup or copy of datafile 8 found to restore
RMAN-06023: no backup or copy of datafile 7 found to restore
RMAN-06023: no backup or copy of datafile 6 found to restore
RMAN-06023: no backup or copy of datafile 5 found to restore
RMAN-06023: no backup or copy of datafile 4 found to restore
RMAN-06023: no backup or copy of datafile 3 found to restore
RMAN-06023: no backup or copy of datafile 2 found to restore
RMAN-06023: no backup or copy of datafile 1 found to restore
RMAN> Exit
Recovery Manager complete.
Edited by: kerrygm on Jun 15, 2011 11:36 AMMaybe making progress.
I got into RMAN and did a List backup command. In looking at the output, I see that it does have the 5/20 backup showing. Here is part of the output:
BS Key Type LV Size Device Type Elapsed Time Completion Time
965689 Full 19.86M DISK 00:00:01 16-JUN-11
BP Key: 967942 Status: AVAILABLE Compressed: NO Tag: TAG20110616T231223
Piece Name: F:\BACKUPS\CSPROD\C-368871413-20110616-01
SPFILE Included: Modification time: 16-JUN-11
SPFILE db_unique_name: CSPROD
Control File Included: Ckp SCN: 369596068 Ckp time: 16-JUN-11
BS Key Size Device Type Elapsed Time Completion Time
966218 403.84M DISK 00:00:00 20-MAY-11
BP Key: 967842 Status: AVAILABLE Compressed: YES Tag: TAG20110520T231012
Piece Name: F:\BACKUPS\CSPROD\A1\CSPROD_ARCH_5844
List of Archived Logs in backup set 966218
Thrd Seq Low SCN Low Time Next SCN Next Time
1 2112 237027300 20-MAY-11 237046947 20-MAY-11
1 2113 *237046947* 20-MAY-11 237059284 20-MAY-11
1 2114 237059284 20-MAY-11 237216514 20-MAY-11
1 2115 237216514 20-MAY-11 237709545 20-MAY-11
1 2116 237709545 20-MAY-11 237722825 20-MAY-11
1 2117 237722825 20-MAY-11 237730431 20-MAY-11
1 2118 237730431 20-MAY-11 237860199 20-MAY-11
I then changed my rman script to use the *237046947* SCN number that says it is from 5/20. I them kicked off my rman script and got the following result.
Spooling started in log file: c:\temp\clone_CSPROD_CSPRSUM1.log
Recovery Manager11.1.0.7.0
RMAN> #connect catalog 'rmancat/rmancat@rmancat';
2> # target is the source and auxiliary is destination
3> #connect target sys/<pwd>@csprod
4> #connect auxiliary /
5>
6> run {
7> allocate auxiliary channel d1 type disk format 'F:\backups\CSPROD\d1\CSPROD_DATA_%s';
8> allocate auxiliary channel d2 type disk format 'F:\backups\CSPROD\d2\CSPROD_DATA_%s';
9> allocate auxiliary channel d3 type disk format 'F:\backups\CSPROD\d3\CSPROD_DATA_%s';
10> allocate auxiliary channel d4 type disk format 'F:\backups\CSPROD\d4\CSPROD_DATA_%s';
11> allocate auxiliary channel a1 type disk format 'F:\backups\CSPROD\a1\CSPROD_arch_%s';
12> ##Archivelog number get from sql archive log list command
13> set until sequence 237046947;
14> ##set until time "to_date('2011-05-20 08:00:00', 'YYYY-MM-DD HH24:MI:SS')";
15> duplicate target database to CSPRSUM1 nofilenamecheck
16> logfile
17> group 1('+DATA/CSPRSUM1/onlinelog/redo1a.log', '+FRA/CSPRSUM1/onlinelog/redo1b.log') size 50m,
18> group 2('+DATA/CSPRSUM1/onlinelog/redo2a.log', '+FRA/CSPRSUM1/onlinelog/redo2b.log') size 50m,
19> group 3('+DATA/CSPRSUM1/onlinelog/redo3a.log', '+FRA/CSPRSUM1/onlinelog/redo3b.log') size 50m;
20> }
allocated channel: d1
channel d1: SID=532 device type=DISK
allocated channel: d2
channel d2: SID=533 device type=DISK
allocated channel: d3
channel d3: SID=531 device type=DISK
allocated channel: d4
channel d4: SID=555 device type=DISK
allocated channel: a1
channel a1: SID=534 device type=DISK
executing command: SET until clause
Starting Duplicate Db at 17-JUN-11
RMAN-05529: WARNING: DB_FILE_NAME_CONVERT resulted in invalid ASM names; names changed to disk group only.
contents of Memory Script:
set until scn 373021170;
set newname for datafile 1 to
"+data";
set newname for datafile 2 to
Starting restore at 17-JUN-11
channel d1: starting datafile backup set restore
channel d1: specifying datafile(s) to restore from backup set
channel d1: restoring datafile 00003 to +DATA
channel d2: restoring datafile 00122 to +DATA
channel d2: reading from backup piece F:\BACKUPS\CSPROD\D4\CSPROD_DATA_6149
channel d3: starting datafile backup set restore
channel d3: specifying datafile(s) to restore from backup set
channel d3: restoring datafile 00002 to +DATA
channel d3: restoring datafile 00020 to +DATA
channel d4: restoring datafile 00120 to +DATA
channel d4: reading from backup piece F:\BACKUPS\CSPROD\D2\CSPROD_DATA_6147
channel d1: piece handle=F:\BACKUPS\CSPROD\D3\CSPROD_DATA_6148 tag=TAG20110616T230013
channel d1: restored backup piece 1
channel d1: restore complete, elapsed time: 00:01:15
channel d4: piece handle=F:\BACKUPS\CSPROD\D2\CSPROD_DATA_6147 tag=TAG20110616T230013
channel d4: restored backup piece 1
channel d4: restore complete, elapsed time: 00:03:15
channel d2: piece handle=F:\BACKUPS\CSPROD\D4\CSPROD_DATA_6149 tag=TAG20110616T230013
channel d2: restored backup piece 1
channel d2: restore complete, elapsed time: 00:03:35
channel d3: piece handle=F:\BACKUPS\CSPROD\D1\CSPROD_DATA_6146 tag=TAG20110616T230013
channel d3: restored backup piece 1
channel d3: restore complete, elapsed time: 00:04:55
Finished restore at 17-JUN-11
sql statement: CREATE CONTROLFILE REUSE SET DATABASE "CSPRSUM1" RESETLOGS ARCHIVELOG
MAXLOGFILES 23
MAXLOGMEMBERS 3
MAXDATAFILES 1021
MAXINSTANCES 8
MAXLOGHISTORY 584
LOGFILE
GROUP 1 ( '+DATA/CSPRSUM1/onlinelog/redo1a.log', '+FRA/CSPRSUM1/onlinelog/redo1b.log' ) SIZE 50 M ,
GROUP 2 ( '+DATA/CSPRSUM1/onlinelog/redo2a.log', '+FRA/CSPRSUM1/onlinelog/redo2b.log' ) SIZE 50 M ,
GROUP 3 ( '+DATA/CSPRSUM1/onlinelog/redo3a.log', '+FRA/CSPRSUM1/onlinelog/redo3b.log' ) SIZE 50 M
DATAFILE
'+DATA/csprsum1/datafile/system.1535.754067379'
CHARACTER SET WE8MSWIN1252
contents of Memory Script:
switch clone datafile all;
executing Memory Script
datafile 2 switched to datafile copy
input datafile copy RECID=1 STAMP=754067676 file name=+DATA/csprsum1/datafile/sysaux.1536.754067379
datafile 121 switched to datafile copy
input datafile copy RECID=120 STAMP=754067677 file name=+DATA/csprsum1/datafile/waapp.1653.754067403
datafile 122 switched to datafile copy
input datafile copy RECID=121 STAMP=754067677 file name=+DATA/csprsum1/datafile/cu_custom.1549.754067381
contents of Memory Script:
set until scn 373021170;
recover
clone database
delete archivelog
executing Memory Script
executing command: SET until clause
Starting recover at 17-JUN-11
starting media recovery
Oracle Error:
ORA-01547: warning: RECOVER succeeded but OPEN RESETLOGS would get error below
ORA-01194: file 1 needs more recovery to be consistent
ORA-01110: data file 1: '+DATA/csprsum1/datafile/system.1535.754067379'
released channel: d1
released channel: d2
released channel: d3
released channel: d4
released channel: a1
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03002: failure of Duplicate Db command at 06/17/2011 15:14:54
RMAN-03015: error occurred in stored script Memory Script
RMAN-06053: unable to perform media recovery because of missing log
RMAN-06025: no backup of archived log for thread 1 with sequence 3818 and starting SCN of 372868482 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3817 and starting SCN of 372685133 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3816 and starting SCN of 372593528 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3815 and starting SCN of 372374385 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3814 and starting SCN of 372325053 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3813 and starting SCN of 372316138 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3812 and starting SCN of 372249619 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3811 and starting SCN of 371775981 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3810 and starting SCN of 371643855 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3809 and starting SCN of 371614442 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3808 and starting SCN of 371432892 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3807 and starting SCN of 371121955 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3806 and starting SCN of 371047786 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3805 and starting SCN of 371029095 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3804 and starting SCN of 371018252 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3803 and starting SCN of 370947755 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3802 and starting SCN of 370857440 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3801 and starting SCN of 370814417 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3800 and starting SCN of 370797061 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3799 and starting SCN of 370756569 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3798 and starting SCN of 370746833 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3797 and starting SCN of 370746693 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3796 and starting SCN of 370746568 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3795 and starting SCN of 370746068 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3794 and starting SCN of 370745451 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3793 and starting SCN of 370733767 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3792 and starting SCN of 370674629 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3791 and starting SCN of 370501026 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3790 and starting SCN of 370498513 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3789 and starting SCN of 370497977 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3788 and starting SCN of 370497635 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3787 and starting SCN of 370497319 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3786 and starting SCN of 370496938 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3785 and starting SCN of 370495428 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3784 and starting SCN of 370491173 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3783 and starting SCN of 370390074 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3782 and starting SCN of 370385574 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3781 and starting SCN of 370385310 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3780 and starting SCN of 370385044 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3779 and starting SCN of 370368486 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3778 and starting SCN of 370333960 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3777 and starting SCN of 370330980 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3776 and starting SCN of 370327876 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3775 and starting SCN of 370174433 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3774 and starting SCN of 370148373 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3773 and starting SCN of 370147821 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3772 and starting SCN of 370147623 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3771 and starting SCN of 370141528 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3770 and starting SCN of 369711271 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3769 and starting SCN of 369621694 found to restore
RMAN-06025: no backup of archived log for thread 1 with sequence 3768 and starting SCN of 369595614 found to restore
RMAN> Exit
Recovery Manager complete.
What I am not sure is if the SCN I used in my set until sequence command was from 5/20, when I look at the backup pieces that it is reading to restore from, they appear to be from backup files taken from June.
(e.g channel d1: reading from backup piece F:\BACKUPS\CSPROD\D3\CSPROD_DATA_6148 -- this is a 6/16 backup file).
Also, as you can see it was not able to do a media recovery.
Thanks in advance for your help. -
Missing Pictures.
Have made a rebbot from Time Machine, and now I lack a lot of pictures. Can see icons, but not enlarge them. Especially pictures where 2009 is included in the date is missing?
When I set up my desktop, I can find some of the pictures. Where do They hide, and what shall I do.
Have made back up, but unfortunately a little too late. What to do?
MacBook Pro 15 "late 2008, Processor 2.53 Ghz Intel Core 2 Duo, Graphics NVIDIA GeForce 9400M 256 MB, Software Mac OS X 10.7.4 Lion (11E53).1. You did not get an error message telling you that your iPhoto library was getting full. You got a message telling you that your HD was getting full, right?
OS X needs about 10 gigs of hard drive space for normal OS operations - things like virtual memory, temporary files and so on.
Without this space your Mac will slow down as the OS hunts for space on the disk, files will be fragmented, also slowing things down, apps will crash and the risk of data corruption - that is damage to your files, photos, music - increases exponentially.
Your first priority is to make more space on that HD. Nothing else can be done until you do.
Purchase an external HD and move your Photos and Music to it. Both iPhoto and iTunes can run perfectly well with the Library on an external disk.
Your Library has been damaged from being run on an overfull disk.
How much free space on it now? -
I can not connect to the ITunes store. I have updated my apple ID and made sure that everything is set correctly. However, I can not purchase or update any apps no matter what I do. My partner has the same phone and hers works perfectly. I'm not sure how to sort this out. Please help
Thanks
AndyI've been having this problem for weeks and have found no solution to it. There are lots of other people with this issue too if you look back on the boards. I even e-mailed AND called Apple and have had no luck. I tried all the suggestions they gave me and all the ones I found on here- nothing worked. I even uninstalled and re-installed iTunes (boy was that a pain!) and no difference.
The weird part is that I have an old laptop that works and if I buy music with the laptop I can download it with my regular computer buy buying does not work on my regular computer. That tells me it's not a connection issue. I can't get to my account either.
I can't figure out why an issue that has kept so many people from purchasing a product has been ignored! -
How can I recover an old/disused iCloud account. I was having some issues with my apple id so I restored my iPad, I am now stuck on the activation screen as I no longer use the iCloud account i used to set up the iPad and can't remember the address or pas
I have the same problem - it is maddening. I rely on this iPad for work so this is not just an annoyance! The above solutions of changing the appleid on the device or on the website do not work.
The old email address no longer exists - I haven't used it in a year probably and I no longer have the account. I logged into the appleid website and there is no trace of the old email address so there is nothing that can be deleted or changed there. On the iPad there is no trace of the old email address so nothing can be deleted there either. I have updated the iPad software and the same problem comes right back. Every 2 seconds I am asked to log in using the old non-existent email. The device is currently useless.
The only recent change to anything was the addition of an Apple TV device, which was set up using the correct login and password.
Does anyone have any ideas? The iPad has been backed up to the iCloud so presumably it now won't recognize the current iCloud account? So restoring may notbe an option? -
I just bought a new MacBook Air. In my old one, I could go from screen to screen by using three fingers to swipe over the key pad. This one just sits there. It is Yosemite. How do I set up preferences so I can use three fingers to move from screen to screen?
Those choices are controlled via System Preferences, Trackpad.
-
How do I set up iMessage so I can send messages from my iPad to my iPhone using the same apple id
I am trying to set up iMessage so I can send and receive messages on my iphone 5 and my iPad using the same apple id.
I assume that you want to keep the same Apple ID on both devices for downloads and purchases but you just want to know how you can use Messages on both devices without creating a new Apple ID.
On one of the two devices ....Settings>Messages>Send and Receive at>You can be reached by iMessage at>add another email address ... and enter another working email address. After you enter the email address and it is verified by Apple, go to the InBox of that email account, read the email from Apple and follow the instructions to complete the verification. Then go back to the settings and remove your Apple ID email address. You will now use that new email address at the contact at email address for messages on that device.
You can keep your Apple ID email address and use that one on the other device. -
On iOS 7 when I try to set a new wallpaper why can't I scale and move my photo? Why does it chop off the heads? Anybody else having this problem?
Hi CollBA,
See More Like This to the right. This issue has been discussed several times on this forum.
Cheers,
GB -
My IPAD 3 [5.1.1 (9B206)] has a problem.
- It restarts every three (3) minutes: it goes out then comes back but lost the previous page (auto lock is set to 15 minutes)
- It can no longer connect to the mobile network orange except Wireless (WIFI)Not normal. Take it to an Apple Store for evaluation.
Make a Genius Bar Reservation
http://www.apple.com/retail/geniusbar/
Cheers, Tom -
Windows 8.1-No UEFI firmware setting in advance option. Can't access BIOS with F2-Lenovo B575
There was Windows 7 Home Premium on my machine before (Lenovo B575)and I could access the BIOS and Boot Menu pressing F2 and F12. I installed Windows 8 Enterprise version first and lost the ability to go into the BIOS. I upgraded this version to 8.1 with
same results. In advanced option I don't have UEFI firmware setting tile. So I can't choose to get to the BIOS with this method. I have tried to go into the BIOS at the boot pressing F2 and many other keys with no result. The OS in both cases 8 and 8.1 hung
several times during the installation process. I had to manually reboot machine during installation several times. After the windows were installed the system still can't shut down or restart normally and I have played with different settings in power / shutdown
option. Please help. I need to be able to access my BIOS at boot or Windows level. Any help will be greatly appreciated. Thanks.Hi,
The method to enter into advanced boot option in Windows 8\8.1 is different from Windows 7, pressing F12 during boot may not work because the booting process in Windows 8\8.1 is too fast. Here's an document from Lenovo website:
http://support.lenovo.com/en/documents/ht081446
NOTE
This
response contains a reference to a third party World Wide Web site. Microsoft is providing this information as a convenience to you.
Microsoft
does not control these sites and has not tested any software or information found on these sites.
Please Note the sentence at the end: Lenovo preloaded Windows 8/8.1 is set up with UEFI boot. If your computer is not fitted with UEFI boot, you can only enter BIOS setup or UEFI firmware via the traditional method.
that means If you installed Windows 8\8.1 the U/EFI way you should be able to access UEFI options,
To check if you boot UEFI way, run in admin command prompt:
bcdedit
for example:
If path ends in
.efi - you boot U/EFI way, and path ends in .exe - you boot normal BIOS way.
Yolanda Zhu
TechNet Community Support -
Need to download a programme to set up VPN but I can't access the website as it is also blocked in china? how do I install the programme if I cant download it or have it on a external hard drive.
Not sure I understand you correctly.. Are you currently in China, and therefore unable to download the app? Also, which program is it that you're trying to get?
-
Problem: Cannot send mail unless Password is transmitted insecurely & Port is set to 587.. Can receive mail but can't send Code 501..
Need help with T-bird.. My OS is Win XP-64..Have been using Mozilla for about 10 years with little or no problems.. This happened when I upgraded to 3.17.. Spent hours on T-Bird diagnostics web site.. Called Comcast & talked to a net tech.. he ran some tests on his end & had me log into my Comcast e-mail account & all worked well,, so he concluded the problem was in T-Bird.. He had me change my port to 587 & disable connection security & authentication to none & I was able to send mail.. That was all he could do.. Comcast was working.. the problem is in T-Bird.. Can any one help with this problem.. I don't want to send mail with my password transmitted insecurely..
Thanks
RichardIt was not intended to be "snide". You said two separate things that at face value would be out of the ordinary.
I considered if it might be a typo for 31.7. Since 31.5 is the current formal release, I would have to thank you for volunteering to test a pre-release beta version. If it was truly 3.1.7 then it would appear that you have chosen, or have become stuck with a somewhat ancient version. In either case it's harder to reach out to you with any meaningful comments or advice. However I do watch various other sites and newsgroups and I don't see a clamour of distressed users, so it seems fair to suppose that this feature isn't actually broken in 31.7.
And you said XP 64. XP is obsolete and no longer supported and if there is a 64-bit version, then again you have set yourself apart from the mainstream.
I had a look at the comcast site and found some puzzling recommendations. Some users come here asking how to set up a secured connection in Thunderbird when it isn't offered by the server. Comcast are different, in that they mention the ports 143 and 587, and also 993 and 465. So far so good, in that security is actually on offer, but they also suggest that you enable SSL, regardless of which port is being used. It would be unusual and unconventional to offer TLS or SSL on ports 143 and 587. STARTTLS would be more credible on these ports.
Have you tried IMAP on 993 and SMTP on 465? SMTP on 587 with SSL, or TLS, is not impossible, but is improbable. -
How to set special rows in jtable not selectable
Hello programmers,
anybody knows how to set special rows(p.E. row 0) in jtable not selectable.
in advance thanks for your answerstable = new JTable(...)
public void changeSelection(int row, int column, boolean toggle, boolean extend)
if (row == 0)
return;
else
super.changeSelection(row, column, toggle, extend);
};
Maybe you are looking for
-
Can repair prices be reduced when giving 2 devices when only repairing 1 of them?
-
Problem with Profiles in AC RAR 5.3
Hi friends, I'm trying to perform a syncro from the profiles in an HR ERP system with RAR 5.3 (SP 11.2). I only get a part of the profiles. The other roles are read by the system, but somehow, they are ignored. Log: Jan 9, 2012 11:05:30 AM com.virsa.
-
Building custom components in jsf 1.2
HI all i am having custom component which has one text field and button together which is extended from a panelgroup component and adding text field and button and child component to this. in jsf1.1 i am not getting any error, but jsf 1.2 i am gettin
-
HT2731 Why will not let you use an Apple ID for free when reseted
Why if you reseted a iphone 4 that already had an free Apple ID on it but when you try to make a other free Apple ID on the same iphone 4 but reseted it still will not let you get an new one
-
Anybody has successfully getting the RFC.exception in a synchronous call via BPM? What i mean, is to get the RFC.exception then use it inside BPM. I have already searched the forum, and i think nobody have done it before. Any clue guys??? Thank you v