Setting the TFTP destination for RME Archive Sync

Hi,
We are attempting to do an Archive Sync from RME in LMS 3.2.
LMS is installed on a Solaris device with multiple VNICs (let's define VNIC1 IP as 1.1.1.1 and VNIC2 IP as 10.0.0.1). The network which has managed devices on it is connected to NIC 2 in the 10.0.0.0 range. We use VNIC 1 to access LMS. There is no routing between 1.1.1.1 and 10.0.0.0.
Now, I understand that when RME attempts to sync a switch, it starts and SSH session into the device and triggers a "copy flash: tftp:" command. This is apparent from the debug logs from RME.
These TFTP based retrievals are failing because RME is setting the TFTP destination to the IP from VNIC 1 (in our case, to 1.1.1.1). Is there any way to force RME to use another IP address for the TFTP destination?
Thank you.
- JMS

you should be able to workaround this by going to
RME > Administration > System Preferences > RME Device Attribute > Add Natted RME IP Address
and enter 10.0.0.1 as the Natted IP address

Similar Messages

Set the default size for all archive mailboxes including the ones it will be created in the future

Hi there.
We are in the phase where we Will enable Online Archive for all the users.
We see that the default Archiving Quota is set up for 50 GB. We have found this powershell command on MsTechnet forum
Get-Mailbox -resultsize unlimited | where {$_.ArchiveDatabase -ne $null} | set-mailbox -ArchiveQuota 7GB -ArchiveWarningQuota 6GB
which I guess it will set up the ArchiveQuota to 7GB to all the users, true?
The question is if this command will work only for those users who currently have archiving enabled or it Will also work for those users which we are planing to enable archiving in the future?
The idea is that everyone would not have 50GB by default and this should be a default value also for those who currently do not have archiving enabled.
with best regards,
bostjanc

Hi there.
I don't quite get it.
I have created "for example" a database called: STH ARCHIVE.
Then if I take look on properties of this database this is how it's shown:
And now here comes the "tricky part" which is a little bit odd to me.
I have enabled archive on my mailbox and selected this STH ARCHIVE DB to hold this archive mailbox.
Then I have manually ran ManagedFolderAssistant for my account: Start-ManagedFolderAssistant -Identity "my-email-address"
And after I have greped the size of my mailbox:
Get-Mailbox | Get-MailboxStatistics -Archive | Sort totalitemsize -desc | ft displayname,totalitemsize, itemcount >C:\report-archive-database-mailboxes.txt
And get the result:
Personal Archive - MYUSERNAME
TotalItemSize: 4.071 GB (4,371,586,689 bytes)
ItemCount: 55227
So now I don't understand how I was able to go thru that sizes which are in the upper print screen of archive DB properties?
bostjanc

How do I set the delivery policy for a queue in iMQ 2.0?

The list on page 67 of the 2.0 administration guide appears to be
incomplete. Specifically, I'm interested in knowing how to set
the default delivery policy for a Queue through the jmqobjmgr command.
I need the valid attribute name to pass in to jmqobjmgr.

The "queueDeliveryPolicy" is an attribute of a queue
created in the broker - not in the administered object
destination so that is why you are not seeing that
attribute on the list on page 67.
By default, the broker by will use the "single" queue delivery
policy unless you choose to change the values of the property
"jmq.queue.defaultdeliveryPolicy" to SINGLE, ROUND-ROBIN, or
FAILOVER. If you would like to do this, see the Chapter 4
in the admin guide on "Starting and Configuring the Broker".
It may be easier to set the delivery policy for just one queue.
To do this, you can use the following command:
jmqcmd create dst -n myQueue -t q -o "queueDeliveryPolicy=f"
where valid values to queueDeliveryPolicy is f, s, r.
You can do a 'jmqcmd -H' to get more info on queue attributes or
see Chapter 6 in the admin guide on "Creating and Destroying Destinations".

How to set the default values for print options

Hi all,
We can set the default value for print options, just like Logical destination、numbers of messages、print immediately and so on, so where we should to maintain these default?

Hi Sandy,
This can be done by an abaper by making changes in the driver program. The Driver program feeds all the data which u have mentioned for printing.
if the driver program is standard. copy to an z type and make modification on printer settings on the driver program code.
this will surely solve the issue.
Regards
Gunaseelan

TS3992 How can I back up an iphone when I haven't set the phone up for back ups & the touch screen doesn't work? The phone can receive calls (not answer) & the pictures & messages can be seen but touch screen doesn't work to unlock the phone or select any

How can I back up an iphone when I haven't set the phone up for back ups & the touch screen doesn't work? The phone can receive calls (not answer) & the pictures & messages can be seen but the touch screen doesn't work to unlock the phone or select anything. We want to save/transfer pictures, contacts, and music to the replacement phone.

Try backing it up to your computer with iTunes. Connect it to your computer, open iTunes, click on the name of the phone in iTunes, go to the Summary tab of your iTunes sync settings and click Back Up Now. Also go to File>Devices>Transfer Purchases to transfer you apps and other purchased media to your iTunes library.

SRM 4.0- How to set the default values for product type (01) only for SC

The radio button Service should not be visible.
Also for search help (e.g. search for internal products) where a search should only be possible for product type 01 (goods). The system should not display the product type and internally always search for goods only.
How to set the default values for product type (01) only for SC
We needs to use Search help BBPH_PRODUCT which having parameter PRODUCT_TYPE
Here we can set defalut value 01 but it is not correct one since same search help is using several places.
We need to limit the search help results only for SC.
Kindly help out me ASAP.

The easiest way to set defautl values is to edit the batch class.
Goto the characteiristic and go to update values.
In here you probably have something like 0 - 100 as a spec range.
On the next line enter the default value within this range. At the end of the line, click in the box in the column labelled "D". This indicates the defautl value for the characteristic.
If you need to you can do this in the material classification view as well.
Just to be clear, these values will only show up in the batch record. You can not have defautl values in resutls recording screens.
FF

How can i set the alternating colors for a table rows

Dear All,
Please any one help me how can i set the Alternating colors for Table Rows.
i created a theam there i set the background alternating color to brown and i set the table design properity to alternating. but it is not reflecting.

Hi,
The design property in Table properties should work for your requirement. Select "alternating" value for design.
Please see the API below:
design
Determines the appearance of the table. The property design can take the following values and is represented by enumeration type WDTableDesign.
alternating - The table rows are displayed alternately in a different color.
standard - The table background has one color. The individual table rows are displayed with grid net lines.
transparent - The table background is transparent. The individual table rows are displayed without grid net lines.
Check whether you have changed the right property or not? Also table should contain more than one rows to test this scenario.
Regards,
Jaya.
Edited by: VJR on Jun 17, 2009 6:43 PM

How do I set the aspect ration for 4:3 or for 16:9?

How do I set the aspect ration for 4:3 or for 16:9 in Adobe PE12?

PulcinellaNM
What computer operating system is your Premiere Elements 12 running on? Have you updated from 12 to 12.1 Update via a project's Help Menu/Update? If not, please do so. That is all background information for now.
As for the question that you are posting....
I think we need to go a lot deeper into what you are doing. Here are some considerations
The aspect ratio setting is in the import settings. In Premiere Elements 12 Expert workspace, the project automatically sets the project preset based on the properties of the first video file that you drag to the Expert workspace Timeline. If your video's properties include a 16:9 flag, then the project settings will have a 16:9 flag (aspect ratio). If you do not want the project to set the project settings automatically, you can set the project settings yourself manually with File Menu/New/Project and then import your source video.
If a problem exists where imported 16:9 video is presenting in Premiere Elements as 4:3 instead of 16:9 (typical of the JVC .mod file issue), then you can set the pixel aspect ratio under Interpret Footage feature inside the project workspace.
At this point, I think it best for you to give more details and background behind your question so that we can be sure that we are giving you the information that you need to succeed in your projects.
If you need clarification on anything written, please do not hesitate to ask for clarification.
Thank you.
ATR

Photos will not allow me to set the key picture for the album or event

Photos will not allow me to set the key picture for the album or event - it is set to grey !
Anyone else had this and found why ?
new PHOTO app replacing iPhoto bugs/ Problems OTHER PROBLEMS :
- no longer has a five star rating system
- my keywords for selecting albums are gone.
- cannot copy location of one photo to another
- cannot have an album with keywords AND rating > a value
- cannot set key photo of album/event
- multi parameter search feature gone
Anyone got any ideas how to get around this terrible downgrade of the software ?
BTW I have just discovered that iPhoto and its' libraries are still there, so I can go back but be left behind and frozen in time on this version if I do.
Photos now take up 700Gb whereas it was 350Gb #@!$#@!@#!@#
Thanks

That are all good points - but Photos is a completely new application. and it is only version 1.
Continue to use iPhoto, girraween; the next update to Photos will probably add a few more features.
iPhoto 9.6.1 is working very well with MacOS X 10.10.3.
The migration let iPhoto installed and also your iPhoto Library will still work with iPhoto.
If you did not uninstall iPhoto, it will still be there in your Applications folder. And if you had updated to the latest version iPhoto 9.6.1 before you upgraded to MacOS X 10.10.3, you can simply drag iPhoto back to the Dock from your Applications folder and continue to use it. Double click iPhoto and confirm, that you want to open iPhoto and not Photos. It is not compulsory to use Photos, while it it still the first release. When you launch iPhoto, you will see a warning, that the iPhoto Library has been migrated to Photos, but simply click the "Open iPhoto" button.The library will still work with iPhoto. ()see: If Photos won't open a library that you already migrated - Apple Support
If your iPhoto version is not iPhoto 9.6.1, you need to update it.
See this User Tip:
Usually it will work to reinstall instead of updating:
Get iPhoto 9.6.1 if you didn't update before OS... | Apple Support Communities
The main idea is to move the iPhoto app to the Trash, so Spotlight does not see it as installed, reload the AppStore, and then to try to download again from the App Store - from your Purchases tab, not from the main page, since you can neither buy iPhoto nor update it, but you can reinstall, if your AppleID is associated with it.
Meanwhile you may want to send a feature request to Apple using the feedback form. Apple - Photos - Feedback
I hope, Apple will listen and add more features to Photos to make it usable for large Photo Libraries.

"I would like to know how to set the default view for the columns. Somewhere I read it could be done in by music icon under Library. Can't find it. Thanks

"I would like to know how to set the default view for the columns that are shown in iTunes. Every time I open it, I have to either go to the options, or right-click to get the pop-up options, and delete "rating" and add "composer." I'd really like to just do it once and be done with it." Somewhere I read you could do this by clicking on the Music icon under LIBRARY then arramge the columns. Trouble is, I can't find a Musi Folder or icon in my user library.
Any help would be appreiated. OSX 10.9.2 iTunes version 11.1.5 Thanks!!! CW!

From the iTunes menu bar try View>Show View Options. Make sure what you want to see is checked and what you don't is unchecked. You can do this (may need to do this) for any playlists, your main Library, etc.
Good luck
srb

How do you set the font color for a specific entire row inside a JTable?

How do you set the font color for a specific entire row inside a JTable?
I want to change the font color for only a couple of rows inside a JTable.
I've seen some ways to possibly do this with an individual cell.
Clarification on changing the font color in an individual cell would be helpful too if
there is no easy way to do this for a row.

hai,
Try out with this piece of code.Create your table and assign the renderer to each column in the table.
CellColorRenderer m_CellColorRenderer = new CellColorRenderer();
for(int i=0;i<your_JTable.getColumnCount();i++)
your_JTable.getColumnModel().getColumn(i).setCellRenderer(m_CellColorRenderer);
class CellColorRenderer extends JLabel implements TableCellRenderer
CellColorRenderer()
setOpaque(true);
setHorizontalAlignment(LEFT);
setVerticalAlignment(CENTER);
setBackground(Color.white);
setForeground(Color.black);
protected void setValue(Object value)
     setText((value == null) ? "" : value.toString());
public Component getTableCellRendererComponent(JTable table,Object value,boolean isSelected, boolean hasFocus, int row,int column)
     if(isSelected == true)
          setForeground(Color.red);
     else
          setForeground(Color.black);
     setValue(value);
     return this;
regards,
bala

How to set the AS2 fileName for outbound Functional Ack 997 auto generated by Oracle B2B

Hi Friends,
How to set the AS2 fileName for outbound Functional Ack 997 auto generated by Oracle B2B.
External Trading Partner is sending the EDI 856 via AS2 URL to our Oracle B2B Server.
In the inbound 856 agreement, we have checked the option of Funtional Ack and also Functiona Ack handled by B2B is yes.
We have the outbound agreement which is sending that Functional ack 997 (auto generated by oracle b2b) and we have specified the Outbound AS2 channel of the Partner.
997 doc is being sent to external partner using AS2 channel, but the filename is generating as '40101'.
Please can you let me know how to set the AS2 fileName for outbound Functional Ack 997 auto generated by Oracle B2B.
Appreciate your valuable answers!!
Thanks,
Amirineni

Amirineni,
AFAIK, there is no option to set the file name when the 997 is generated automatically by B2B.
Alternatively, if this is a must requirement, you can generate the FA from backend and send to B2B with MSG_TYPE =9. In this case, you can set the header with filename (How to set the actionname property in B2B 11g)

This message could not be delivered because your SMTP settings are not set. Please use the Accounts Preferences panel to set the SMTP options for your account.

I am not able to send out an email. I keep getting the following message: This message could not be delivered because your SMTP settings are not set. Please use the Accounts Preferences panel to set the SMTP options for your account. Can someone help me with this?

We need some information, starting with the email provider (eg. Google, Yahoo, Bellsouth, etc)

How do you set the default magnification for Acrobat. All documents that I open enlarge to 174% and are too big.

How do you set the default magnification for Acrobat. All documents that I open enlarge to 174% and are too big. I see how to change the size after the document is open by going to File/properties/initial view and saving this setting. I want all documents to open at 100% when they are first opened. Can I set this as a default view?

Hey Kris,
You might go to Edit> Preferences> Zoom
Do this without opening any particular PDF so that it applies to the program itself and not just one document.
Try this and then let me know.
Regards,
Anubha

How do I set the default folder for file - open file... ?

When I save a file, photo, etc., the default folder for OPENING a file becomes the last folder I SAVED to - even after closing and reopening Firefox. Is there a way to maintain the same default folder for opening files?
Thanks.

Originally posted by: kwarner.uneedspeed.net
Well... I found over 200 bugs none of which seemed to talk about setting
the default folder. I probably missed the relevant bug in the spew.
I ask a question here as a last resort -- after I've done what I think
is an appropriate search for answers.
But thanks for your help in any case.
Daniel Megert wrote:
> DemonDuck wrote:
>
>> When I need to open a file not in the workspace, I use File -> Open File.
>>
>> But the default folder it opens is in C:\Documents and
>> Setting\Administrator
>>
>> I would like File -> Open File to first open in someplace more
>> reasonable -- like the workspace.
>>
>> How do I set the default folder for File -> Open File ????
>
>
> Is your '?' key broken? Check bugzilla there's a feature request
> regarding your question.
>
> Dani

Setting the TFTP destination for RME Archive Sync

Similar Messages

Maybe you are looking for