Setting up a dsl as failover on 2600 series router

I need to setup a failover line. the primary line is a T1 which is connected to serial interface. the secondary line is install to the FE0/1 of a 2600 series router. when i configure the nat pool IPOOL i get a error message saying that dynamic maping in use i need to have a sample config to complete this

Hii,
the msg comes up in there at nat sessions moving on...so u need to clear the ip translations and try executing the command.. if still msg crops.then u might hv to shut the local inside nat interface for a while ..
pls do rate the post.

Similar Messages

  • Cisco 2600 series router and cable modems

    Hi everyone, I am just about to get started preparing for my CCNA... I am looking to pick up some used Cisco 2600 series routers to set up a home lab. I am wondering if it is possible to connect a cable modem directly to a 2600 series router? If so, do I need a certain type of WIC? I want to go from my cable modem, to a router, to my switch. Thanks in advance!

    Hi,
    Yes you can, using the Ethernet port on the cable modem, you can connect the cable modem to the router 2600, and the 2600 comes with builtin ethernet or fastethernet (according to your platform).
    HTH,
    Mohammed Mahmoud.

  • IOS for MPLS on 1800 & 2600 series router

    Hi,
    What IOS version to be on 1800 & 2600 series routers to support MPLS

    For MPLS Support on 1800 & 2600 Series you need IOS Release 12.3(14)*T or later.
    Cisco IOS Release 12.3(14)YT on 1800 Series ISR
    http://www.cisco.com/en/US/prod/collateral/routers/ps5853/prod_bulletin0900aecd802d0c05.html
    Cisco IOS Software Release 12.3T Features
    http://www.cisco.com/en/US/products/sw/secursw/ps5318/prod_bulletin09186a00801abfda.html

  • Reset 2600 series - no console connection

    I used this article to reset a 2600 Series router/voice gateway to it's default settings but it's not connection to my console connection after the reload....
    http://www.cisco.com/en/US/products/sw/iosswrel/ps5187/products_tech_note09186a00802017a1.shtml
    Any suggestions for how I can get in there again?

    you should be set for 9600 8 none 1, and flow control set to off.
    HTH,
    Steve
    Please remember to rate useful posts, and mark questions as answered

  • [SOLVED] Setting up a DSL router?

    Hello there.
    I am having trouble setting up my DSL router with Archlinux. It is currently running with Vista and has all the correct settings already configured. I am unsure of how to properly set it up and have tried various configurations which resulted in pppoe-start timing out, sometimes with an error. I have two network cards (One integrated into my Asus A8V motherboard and the other a 3com.) I am not sure which is eth0 and which is eth1 but I set rc.conf to eth0 and tried both.
    The DSL router is a Dynalink RTA1320 which I believe runs a version of linux with a 2.4.x kernel.
    Isn't including the login and DNS addresses when running pppoe-setup unneccesary as the router is already set up with them? I have setup the router's IP address (192.168.1.1) as the default gateway.
    Last setting tried was:
    lo="lo 127.0.0.1"
    eth0="dhcp"
    INTERFACES=(eth0)
    gateway="default gw 192.168.1.1"
    routes=(!gateway)
    I have also tried routes=(gateway).
    Any advice?
    Last edited by Phineas (2008-03-15 23:22:34)

    Thankyou everyone for your help. I re-installed Arch ("oh those newbies!") and then went straight to configuring rc.conf without using pppoe-setup. I have configured rc.conf like so:
    lo="lo 127.0.0.1"
    eth0="dhcp"
    INTERFACES=(eth0)
    gateway="default gw 192.168.1.1 eth0"
    ROUTES=(!gateway)
    DAEMONS=(syslog-ng network netfs crond dhcpd)
    My 3com network card's module was already listed first in the modules for Linux to load (Google helped me find out what my card's module is.) Also, http://bbs.archlinux.org/viewtopic.php?id=45065 was helpful.
    I rebooted with the router plugged in. No error message came up after NETWORK as it started. Ping www.google.com worked!
    "I'm in my way, from misery to happiness..."
    Last edited by Phineas (2008-07-03 01:36:47)

  • Trouble getting Cisco 2600 Series AP to stay joined to WLC 5508

    Hi,
    I have recently been tasked with upgrading our old Autonomous APs to LWAPs.  We have a 5508 WLC at our Virtual Co-Lo and I am using Flexconnect to accomadate local switching and dhcp at our sites.  I have upgraded over 50 APs and joined them to the controller.  These include only 1130AG and 1240AG models.  However they are working flawlessly and staying connected to the controller.  The issue I'm having is with a new batch of 2600 series APs staying connected to the controller.  I have attempted to do research into what may be causing the disconnects but have yet to find a solution.  I am using DNS to resolve the CAPWAP & LWAPP queries from the APs to the controller accross our WAN.  In reading other posts I thought it may be an issue with packets getting dropped but have had our Vendor who manages Sonicwalls at both ends of the WAN confirm for me there is no packet loss.  Below are logs I gathered using puttty from the AP & WLC.  Any help would be greatly appreciated.
    AP I'm doing the testing on:
    NAME: "AP2600", DESCR: "Cisco Aironet 2600 Series (IEEE 802.11n) Access Point"
    PID: AIR-CAP2602I-A-K9 , VID: V01, SN: FTX1740J8V1
    WLC in question:
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.3.112.0
    Bootloader Version............................... 1.0.1
    Field Recovery Image Version..................... 6.0.182.0
    Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
    Build Type....................................... DATA + WPS
    System Name...................................... wificontroller
    System Location.................................. Corp
    System Contact................................... Net Engineer
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
    Redundancy Mode.................................. Disabled
    IP Address....................................... 10.250.32.8
    Last Reset....................................... Software reset
    System Up Time................................... 190 days 3 hrs 34 mins 24 secs
    System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)
    Configured Country............................... US  - United States
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    --More-- or (q)uit
    Internal Temperature............................. +38 C
    External Temperature............................. +20 C
    Fan Status....................................... OK
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 14
    Number of Active Clients......................... 71
    Burned-in MAC Address............................ C8:9C:1D:8C:52:E0
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Absent
    Maximum number of APs supported.................. 100
    Here is the output that keeps on occuring as the AP joins the WLC for a brief time and then changes to standalone mode
    WT-4thFlr-AP3#
    *Dec 14 15:42:04.419: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(CAPWAP_WTP_EVENT_REQUEST
    ., 3)
    *Dec 14 15:42:11.443: %EVT-4-WRN: Write of flash:/event.capwap done
    *Dec 14 15:42:11.483: %LWAPP-3-CLIENTERRORLOG: Switching to Standalone mode
    *Dec 14 15:42:11.487: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
    *Dec 14 15:42:11.487: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.250.32.8:5246
    *Dec 14 15:42:11.571: %WIDS-6-DISABLED: IDS Signature is removed and disabled.
    *Dec 14 15:42:21.575: %CAPWAP-3-ERRORLOG: Selected MWAR 'wificontroller'(index 0).
    *Dec 14 15:42:21.575: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Dec 14 15:42:12.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.250.32.8 peer_port: 5246
    *Dec 14 15:42:14.303: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.250.32.8 peer_port: 5246
    *Dec 14 15:42:14.303: %CAPWAP-5-SENDJOIN: sending Join Request to 10.250.32.8
    *Dec 14 15:42:15.127: Starting Ethernet promiscuous mode
    *Dec 14 15:42:15.535: %LWAPP-4-CLIENTEVENTLOG: OfficeExtend Localssid saved in AP flash
    *Dec 14 15:42:15.667: ac_first_hop_mac - IP:10.1.2.250 Hop IP:10.1.2.250 IDB:BVI1
    *Dec 14 15:42:15.667: Setting AC first hop MAC: 0017.c575.a23c
    *Dec 14 15:42:15.855: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller wificontroller
    *Dec 14 15:42:15.911: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
    *Dec 14 15:42:15.911: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
    *Dec 14 15:42:15.911: %LWAPP-4-CLIENTEVENTLOG: No LS Flex ACL map configuration file to load. Connect to controller to get configuration file
    *Dec 14 15:42:15.915: %LWAPP-4-CLIENTEVENTLOG: No Central Dhcp map configuration file to load. Connect to controller to get configuration file
    *Dec 14 15:42:15.915: %LWAPP-3-CLIENTERRORLOG: Switching to Connected mode
    *Dec 14 15:42:23.639: %WIDS-6-ENABLED: IDS Signature is loaded and enabled
    *Dec 14 15:42:34.615: %CLEANAIR-6-STATE: Slot 0 disabled
    *Dec 14 15:42:34.615: %CLEANAIR-6-STATE: Slot 1 disabled
    *Dec 14 15:45:43.783: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(CAPWAP_WTP_EVENT_REQUEST
    ., 11)
    *Dec 14 15:45:43.787: %LWAPP-3-CLIENTERRORLOG: Switching to Standalone mode
    *Dec 14 15:45:43.787: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
    *Dec 14 15:45:43.787: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.250.32.8:5246
    *Dec 14 15:45:43.867: %WIDS-6-DISABLED: IDS Signature is removed and disabled.
    *Dec 14 15:45:53.867: %CAPWAP-3-ERRORLOG: Selected MWAR 'wificontroller'(index 0).
    *Dec 14 15:45:53.867: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Dec 14 15:45:44.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.250.32.8 peer_port: 5246
    *Dec 14 15:45:46.315: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.250.32.8 peer_port: 5246
    *Dec 14 15:45:46.315: %CAPWAP-5-SENDJOIN: sending Join Request to 10.250.32.8
    *Dec 14 15:45:46.487: Starting Ethernet promiscuous mode
    *Dec 14 15:45:49.903: %LWAPP-4-CLIENTEVENTLOG: OfficeExtend Localssid saved in AP flash
    *Dec 14 15:45:50.031: ac_first_hop_mac - IP:10.1.2.250 Hop IP:10.1.2.250 IDB:BVI1
    *Dec 14 15:45:50.031: Setting AC first hop MAC: 0017.c575.a23c
    Here are the results of debug capwap client event on the AP:
    WT-4thFlr-AP3#debug capwap client event
    CAPWAP Client EVENT display debugging is on
    WT-4thFlr-AP3#
    *Dec 14 15:54:58.335: %CAPWAP-3-EVENTLOG: Echo Interval Expired.
    *Dec 14 15:54:58.335: %CAPWAP-3-EVENTLOG: Sending packet to AC
    *Dec 14 15:54:58.335: %CAPWAP-3-EVENTLOG: Echo Request sent to 10.250.32.8
    *Dec 14 15:54:58.343: %CAPWAP-3-EVENTLOG: Resetting reTransmissionCnt to 0
    *Dec 14 15:54:58.343: %CAPWAP-3-EVENTLOG: Queue Empty.
    *Dec 14 15:54:58.343: %CAPWAP-3-EVENTLOG: Echo Response from 10.250.32.8
    *Dec 14 15:55:08.000: %CAPWAP-3-EVENTLOG: Setting time to 15:55:08 UTC Dec 14 2013
    *Dec 14 15:55:25.579: %CAPWAP-3-EVENTLOG: Sending packet to AC
    *Dec 14 15:55:25.587: %CAPWAP-3-EVENTLOG: Resetting reTransmissionCnt to 0
    *Dec 14 15:55:25.587: %CAPWAP-3-EVENTLOG: Queue Empty.
    *Dec 14 15:55:25.587: %CAPWAP-3-EVENTLOG: Wtp Event Response from 10.250.32.8
    *Dec 14 15:55:25.827: %CAPWAP-3-EVENTLOG: Sending packet to AC
    *Dec 14 15:55:25.835: %CAPWAP-3-EVENTLOG: Resetting reTransmissionCnt to 0
    *Dec 14 15:55:25.835: %CAPWAP-3-EVENTLOG: Queue Empty.
    *Dec 14 15:55:25.835: %CAPWAP-3-EVENTLOG: Wtp Event Response from 10.250.32.8
    *Dec 14 15:55:55.835: %CAPWAP-3-EVENTLOG: Echo Interval Expired.
    *Dec 14 15:55:55.835: %CAPWAP-3-EVENTLOG: Sending packet to AC
    *Dec 14 15:55:55.835: %CAPWAP-3-EVENTLOG: Echo Request sent to 10.250.32.8
    *Dec 14 15:55:55.843: %CAPWAP-3-EVENTLOG: Resetting reTransmissionCnt to 0
    *Dec 14 15:55:55.843: %CAPWAP-3-EVENTLOG: Queue Empty.
    *Dec 14 15:55:55.843: %CAPWAP-3-EVENTLOG: Echo Response from 10.250.32.8
    *Dec 14 15:55:56.000: %CAPWAP-3-EVENTLOG: Setting time to 15:55:56 UTC Dec 14 2013
    *Dec 14 15:56:25.735: %CAPWAP-3-EVENTLOG: Sending packet to AC
    *Dec 14 15:56:25.743: %CAPWAP-3-EVENTLOG: Resetting reTransmissionCnt to 0
    *Dec 14 15:56:25.743: %CAPWAP-3-EVENTLOG: Queue Empty.
    *Dec 14 15:56:25.743: %CAPWAP-3-EVENTLOG: Wtp Event Response from 10.250.32.8
    *Dec 14 15:56:25.983: %CAPWAP-3-EVENTLOG: Sending packet to AC
    *Dec 14 15:56:25.991: %CAPWAP-3-EVENTLOG: Resetting reTransmissionCnt to 0
    *Dec 14 15:56:25.991: %CAPWAP-3-EVENTLOG: Queue Empty.
    *Dec 14 15:56:25.991: %CAPWAP-3-EVENTLOG: Wtp Event Response from 10.250.32.8
    *Dec 14 15:56:55.991: %CAPWAP-3-EVENTLOG: Echo Interval Expired.
    *Dec 14 15:56:55.991: %CAPWAP-3-EVENTLOG: Sending packet to AC
    *Dec 14 15:56:55.991: %CAPWAP-3-EVENTLOG: Echo Request sent to 10.250.32.8
    *Dec 14 15:56:55.999: %CAPWAP-3-EVENTLOG: Resetting reTransmissionCnt to 0
    *Dec 14 15:56:55.999: %CAPWAP-3-EVENTLOG: Queue Empty.
    *Dec 14 15:56:55.999: %CAPWAP-3-EVENTLOG: Echo Response from 10.250.32.8
    *Dec 14 15:56:56.000: %CAPWAP-3-EVENTLOG: Setting time to 15:56:56 UTC Dec 14 2013
    Here are the results of debug capwap client packet detail:
    WT-4thFlr-AP3#
    *Dec 14 15:59:01.823: <<<<   Start of CAPWAP Packet  >>>>
    *Dec 14 15:59:01.823: CAPWAP Control mesg Sent to 10.250.32.8, Port 5246
    *Dec 14 15:59:01.823:         Msg Type   : CAPWAP_ECHO_REQUEST
    *Dec 14 15:59:01.823:         Msg Length : 0
    *Dec 14 15:59:01.823:         Msg SeqNum : 44
    *Dec 14 15:59:01.823: <<<<  End of CAPWAP Packet  >>>>
    *Dec 14 15:59:01.831: <<<<   Start of CAPWAP Packet  >>>>
    *Dec 14 15:59:01.831: CAPWAP Control mesg Recd from 10.250.32.8, Port 5246
    *Dec 14 15:59:01.831:         HLEN 2,   Radio ID 0,    WBID 1
    *Dec 14 15:59:01.831:         Msg Type   : CAPWAP_ECHO_RESPONSE
    *Dec 14 15:59:01.831:         Msg Length : 15
    *Dec 14 15:59:01.831:         Msg SeqNum : 44
    *Dec 14 15:59:01.831: 
    *Dec 14 15:59:01.831:      Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 11
    *Dec 14 15:59:01.831:         Vendor Identifier  : 0x00409600
    *Dec 14 15:59:01.831:
    *Dec 14 15:59:01.831:
        IE            :   UNKNOWN IE 151
    *Dec 14 15:59:01.831:     IE Length     :   5
    *Dec 14 15:59:01.831:     Decode routine not available, Printing Hex Dump
    *Dec 14 15:59:01.831:
    52 AC 80 46 00
    *Dec 14 15:59:01.831: <<<<  End of CAPWAP Packet  >>>>
    *Dec 14 15:59:20.931: <<<<   Start of CAPWAP Packet  >>>>
    *Dec 14 15:59:20.931: CAPWAP Control mesg Recd from 10.250.32.8, Port 5246
    *Dec 14 15:59:20.931:         HLEN 2,   Radio ID 0,    WBID 1
    *Dec 14 15:59:20.931:         Msg Type   : CAPWAP_CONFIGURATION_UPDATE_REQUEST
    *Dec 14 15:59:20.931:         Msg Length : 93
    *Dec 14 15:59:20.931:         Msg SeqNum : 38
    *Dec 14 15:59:20.931: 
    *Dec 14 15:59:20.931:      Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 89
    *Dec 14 15:59:20.931:         Vendor Identifier  : 0x00409600
    *Dec 14 15:59:20.931:
    *Dec 14 15:59:20.931:
        IE            :   RRM_NEIGHBOR_CTRL_PAYLOAD
    *Dec 14 15:59:20.931:     IE Length     :   83
    *Dec 14 15:59:20.931:     Decode routine not available, Printing Hex Dump
    *Dec 14 15:59:20.931:
    00 0A FA 20 08 01 F4 00 07 0A FA 20 08 03 00 01
    01 00 3C 00 B4 2E 06 2E E7 B4 94 51 B2 C7 79 25
    22 FD BE 04 F6 00 00 00 00 00 00 00 00 4F 50 52
    53 2D 57 69 46 69 00 00 00 00 00 00 00 00 00 00
    00 00 00 00 00 00 00 00 00 00 00 00 00 01 06 0B
    01 01 01
    *Dec 14 15:59:20.931: <<<<  End of CAPWAP Packet  >>>>
    *Dec 14 15:59:20.931: <<<<   Start of CAPWAP Packet  >>>>
    *Dec 14 15:59:20.931: CAPWAP Control mesg Sent to 10.250.32.8, Port 5246
    *Dec 14 15:59:20.931:         Msg Type   : CAPWAP_CONFIGURATION_UPDATE_RESPONSE
    *Dec 14 15:59:20.931:         Msg Length : 8
    *Dec 14 15:59:20.931:         Msg SeqNum : 38
    *Dec 14 15:59:20.931: 
    *Dec 14 15:59:20.931:      Type : CAPWAP_MSGELE_RESULT_CODE, Length 4
    *Dec 14 15:59:20.931:         Result Code : CAPWAP_SUCCESS
    *Dec 14 15:59:20.931: <<<<  End of CAPWAP Packet  >>>>
    *Dec 14 15:59:21.139: <<<<   Start of CAPWAP Packet  >>>>
    *Dec 14 15:59:21.139: CAPWAP Control mesg Recd from 10.250.32.8, Port 5246
    *Dec 14 15:59:21.139:         HLEN 2,   Radio ID 0,    WBID 1
    *Dec 14 15:59:21.139:         Msg Type   : CAPWAP_CONFIGURATION_UPDATE_REQUEST
    *Dec 14 15:59:21.139:         Msg Length : 111
    *Dec 14 15:59:21.139:         Msg SeqNum : 39
    *Dec 14 15:59:21.139: 
    *Dec 14 15:59:21.139:      Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 107
    *Dec 14 15:59:21.139:         Vendor Identifier  : 0x00409600
    *Dec 14 15:59:21.139:
    *Dec 14 15:59:21.139:
        IE            :   RRM_NEIGHBOR_CTRL_PAYLOAD
    *Dec 14 15:59:21.139:     IE Length     :   101
    *Dec 14 15:59:21.139:     Decode routine not available, Printing Hex Dump
    *Dec 14 15:59:21.143:
    01 0A FA 20 08 01 F4 00 07 0A FA 20 08 0C 00 01
    01 00 3C 00 B4 2E 06 2E E7 B4 94 51 B2 C7 79 25
    22 FD BE 04 F6 00 00 00 00 00 00 00 00 4F 50 52
    53 2D 57 69 46 69 00 00 00 00 00 00 00 00 00 00
    00 00 00 00 00 00 00 00 00 00 00 00 00 24 28 2C
    30 34 38 3C 40 95 99 9D A1 01 01 01 01 01 01 01
    01 01 01 01 01
    *Dec 14 15:59:21.143: <<<<  End of CAPWAP Packet  >>>>
    *Dec 14 15:59:21.143: <<<<   Start of CAPWAP Packet  >>>>
    *Dec 14 15:59:21.143: CAPWAP Control mesg Sent to 10.250.32.8, Port 5246
    *Dec 14 15:59:21.143:         Msg Type   : CAPWAP_CONFIGURATION_UPDATE_RESPONSE
    *Dec 14 15:59:21.143:         Msg Length : 8
    *Dec 14 15:59:21.143:         Msg SeqNum : 39
    *Dec 14 15:59:21.143: 
    *Dec 14 15:59:21.143:      Type : CAPWAP_MSGELE_RESULT_CODE, Length 4
    *Dec 14 15:59:21.143:         Result Code : CAPWAP_SUCCESS
    *Dec 14 15:59:21.143: <<<<  End of CAPWAP Packet  >>>>
    *Dec 14 15:59:25.547: <<<<   Start of CAPWAP Packet  >>>>
    *Dec 14 15:59:25.547: CAPWAP Control mesg Sent to 10.250.32.8, Port 5246
    *Dec 14 15:59:25.547:         Msg Type   : CAPWAP_WTP_EVENT_REQUEST
    *Dec 14 15:59:25.547:         Msg Length : 14
    *Dec 14 15:59:25.547:         Msg SeqNum : 45
    *Dec 14 15:59:25.547: 
    *Dec 14 15:59:25.547:      Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
    *Dec 14 15:59:25.547:         Vendor Identifier  : 0x00409600
    *Dec 14 15:59:25.547:
    *Dec 14 15:59:25.547:
        IE            :   RRM_LOAD_DATA_PAYLOAD
    *Dec 14 15:59:25.547:     IE Length     :   4
    *Dec 14 15:59:25.547:          slot 0 rxLoad 0 txLoad 0 ccaLoad 33
    *Dec 14 15:59:25.547: <<<<  End of CAPWAP Packet  >>>>
    *Dec 14 15:59:25.555: <<<<   Start of CAPWAP Packet  >>>>
    *Dec 14 15:59:25.555: CAPWAP Control mesg Recd from 10.250.32.8, Port 5246
    *Dec 14 15:59:25.555:         HLEN 2,   Radio ID 0,    WBID 1
    *Dec 14 15:59:25.555:         Msg Type   : CAPWAP_WTP_EVENT_RESPONSE
    *Dec 14 15:59:25.555:         Msg Length : 0
    *Dec 14 15:59:25.555:         Msg SeqNum : 45
    *Dec 14 15:59:25.555: <<<<  End of CAPWAP Packet  >>>>
    *Dec 14 15:59:25.795: <<<<   Start of CAPWAP Packet  >>>>
    *Dec 14 15:59:25.795: CAPWAP Control mesg Sent to 10.250.32.8, Port 5246
    *Dec 14 15:59:25.795:         Msg Type   : CAPWAP_WTP_EVENT_REQUEST
    *Dec 14 15:59:25.795:         Msg Length : 14
    *Dec 14 15:59:25.795:         Msg SeqNum : 46
    *Dec 14 15:59:25.795: 
    *Dec 14 15:59:25.795:      Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
    *Dec 14 15:59:25.795:         Vendor Identifier  : 0x00409600
    *Dec 14 15:59:25.795:
    *Dec 14 15:59:25.795:
        IE            :   RRM_LOAD_DATA_PAYLOAD
    *Dec 14 15:59:25.795:     IE Length     :   4
    *Dec 14 15:59:25.795:          slot 1 rxLoad 0 txLoad 0 ccaLoad 0
    *Dec 14 15:59:25.795: <<<<  End of CAPWAP Packet  >>>>
    *Dec 14 15:59:25.803: <<<<   Start of CAPWAP Packet  >>>>
    *Dec 14 15:59:25.803: CAPWAP Control mesg Recd from 10.250.32.8, Port 5246
    *Dec 14 15:59:25.803:         HLEN 2,   Radio ID 0,    WBID 1
    *Dec 14 15:59:25.803:         Msg Type   : CAPWAP_WTP_EVENT_RESPONSE
    *Dec 14 15:59:25.803:         Msg Length : 0
    *Dec 14 15:59:25.803:         Msg SeqNum : 46
    *Dec 14 15:59:25.803: <<<<  End of CAPWAP Packet  >>>>
    *Dec 14 15:59:30.375: <<<<   Start of CAPWAP Packet  >>>>
    *Dec 14 15:59:30.375: CAPWAP Control mesg Recd from 10.250.32.8, Port 5246
    *Dec 14 15:59:30.375:         HLEN 2,   Radio ID 0,    WBID 1
    *Dec 14 15:59:30.375:         Msg Type   : CAPWAP_CONFIGURATION_UPDATE_REQUEST
    *Dec 14 15:59:30.375:         Msg Length : 17
    *Dec 14 15:59:30.375:         Msg SeqNum : 40
    *Dec 14 15:59:30.375: 
    *Dec 14 15:59:30.375:      Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 13
    *Dec 14 15:59:30.375:         Vendor Identifier  : 0x00409600
            SlotId                  :   0
            Mobile Mac Addr         :   BC:52:B7:E3:17:CB
    *Dec 14 15:59:30.375: <<<<  End of CAPWAP Packet  >>>>
    *Dec 14 15:59:30.375: <<<<   Start of CAPWAP Packet  >>>>
    *Dec 14 15:59:30.375: CAPWAP Control mesg Sent to 10.250.32.8, Port 5246
    *Dec 14 15:59:30.375:         Msg Type   : CAPWAP_CONFIGURATION_UPDATE_RESPONSE
    *Dec 14 15:59:30.379:         Msg Length : 8
    *Dec 14 15:59:30.379:         Msg SeqNum : 40
    *Dec 14 15:59:30.379: 
    *Dec 14 15:59:30.379:      Type : CAPWAP_MSGELE_RESULT_CODE, Length 4
    *Dec 14 15:59:30.379:         Result Code : CAPWAP_SUCCESS
    *Dec 14 15:59:30.379: <<<<  End of CAPWAP Packet  >>>>
    *Dec 14 15:59:30.387: <<<<   Start of CAPWAP Packet  >>>>
    *Dec 14 15:59:30.387: CAPWAP Control mesg Recd from 10.250.32.8, Port 5246
    *Dec 14 15:59:30.387:         HLEN 2,   Radio ID 0,    WBID 1
    *Dec 14 15:59:30.387:         Msg Type   : CAPWAP_WTP_EVENT_RESPONSE
    *Dec 14 15:59:30.387:         Msg Length : 0
    *Dec 14 15:59:30.387:         Msg SeqNum : 47
    *Dec 14 15:59:30.387: <<<<  End of CAPWAP Packet  >>>>
    *Dec 14 16:00:00.387: <<<<   Start of CAPWAP Packet  >>>>
    *Dec 14 16:00:00.387: CAPWAP Control mesg Sent to 10.250.32.8, Port 5246
    *Dec 14 16:00:00.387:         Msg Type   : CAPWAP_ECHO_REQUEST
    *Dec 14 16:00:00.387:         Msg Length : 0
    *Dec 14 16:00:00.387:         Msg SeqNum : 48
    *Dec 14 16:00:00.387: <<<<  End of CAPWAP Packet  >>>>
    *Dec 14 16:00:00.395: <<<<   Start of CAPWAP Packet  >>>>
    *Dec 14 16:00:00.395: CAPWAP Control mesg Recd from 10.250.32.8, Port 5246
    *Dec 14 16:00:00.395:         HLEN 2,   Radio ID 0,    WBID 1
    *Dec 14 16:00:00.395:         Msg Type   : CAPWAP_ECHO_RESPONSE
    *Dec 14 16:00:00.395:         Msg Length : 15
    *Dec 14 16:00:00.395:         Msg SeqNum : 48
    *Dec 14 16:00:00.395: 
    *Dec 14 16:00:00.395:      Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 11
    *Dec 14 16:00:00.395:         Vendor Identifier  : 0x00409600
    *Dec 14 16:00:00.395:
    *Dec 14 16:00:00.395:
        IE            :   UNKNOWN IE 151
    *Dec 14 16:00:00.395:     IE Length     :   5
    *Dec 14 16:00:00.395:     Decode routine not available, Printing Hex Dump
    *Dec 14 16:00:00.395:
    52 AC 80 81 00
    *Dec 14 16:00:00.395: <<<<  End of CAPWAP Packet  >>>>

    Under my AP Policies I only have "Accept Manufactured Installed Certificate (MIC)" checked.  I attempted to add the AP based on MAC Address (c0:67:af:6f:25:70) with this certificate type but still have the same issue.  I then ran the following debug on my controller and this is the output I recieve regarding that MAC.  I tried to cut the output short because it get's somewhat redundant but was unsure what exactly to look for in the output.  Should I be selecting a different certificate type?  I am somewhat new to wireless technologies but doing my best to pick things up so if this seems trivial please forgive my ignorance.
    debug pm pki enable
    *sshpmLscTask: Dec 14 20:42:56.450: sshpmLscTask: LSC Task received a message 4
    *spamApTask6: Dec 14 20:42:58.840: sshpmGetIssuerHandles: locking ca cert table
    *spamApTask6: Dec 14 20:42:58.841: sshpmGetIssuerHandles: calling x509_alloc() for user cert
    *spamApTask6: Dec 14 20:42:58.841: sshpmGetIssuerHandles: calling x509_decode()
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetIssuerHandles: C=US, ST=California, L=San Jose, O=Cisco Systems, CN=AP3G2-c067af6f2570, [email protected]
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetIssuerHandles:   O=Cisco Systems, CN=Cisco Manufacturing CA
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetIssuerHandles: Mac Address in subject is c0:67:af:6f:25:70
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetIssuerHandles: Cert Name in subject is AP3G2-c067af6f2570
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetIssuerHandles: Cert is issued by Cisco Systems.
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetCID: called to evaluate
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetCertFromCID: called to get cert for CID 282aef7e
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetCertFromCID: comparing to row 0, certname >bsnOldDefaultCaCert<
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetCertFromCID: comparing to row 1, certname >bsnDefaultRootCaCert<
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetCertFromCID: comparing to row 2, certname >bsnDefaultCaCert<
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetCertFromCID: comparing to row 3, certname >bsnDefaultBuildCert<
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetCertFromCID: comparing to row 4, certname >cscoDefaultNewRootCaCert<
    *spamApTask6: Dec 14 20:42:58.845: sshpmGetCertFromCID: comparing to row 5, certname >cscoDefaultMfgCaCert<
    *spamApTask6: Dec 14 20:42:58.845: ssphmUserCertVerify: calling x509_decode()
    *spamApTask6: Dec 14 20:42:58.856: ssphmUserCertVerify: user cert verfied using >cscoDefaultMfgCaCert<
    *spamApTask6: Dec 14 20:42:58.856: sshpmGetIssuerHandles: ValidityString (current): 2013/12/15/01:42:58
    *spamApTask6: Dec 14 20:42:58.856: sshpmGetIssuerHandles: ValidityString (NotBefore): 2013/08/25/13:01:22
    *spamApTask6: Dec 14 20:42:58.856: sshpmGetIssuerHandles: ValidityString (NotAfter): 2023/08/25/13:11:22
    *spamApTask6: Dec 14 20:42:58.856: sshpmGetIssuerHandles: getting cisco ID cert handle...
    *spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: called to evaluate
    *spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
    *spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
    *spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<
    *spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<
    *spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<
    *spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<
    *spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: comparing to row 0, ID cert >bsnOldDefaultIdCert<
    *spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: comparing to row 1, ID cert >bsnDefaultIdCert<
    *spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: comparing to row 2, ID cert >cscoDefaultIdCert<
    *spamApTask6: Dec 14 20:42:58.857: sshpmFreePublicKeyHandle: called with 0x2c5f0cb8
    *spamApTask6: Dec 14 20:42:58.857: sshpmFreePublicKeyHandle: freeing public key
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: called to evaluate
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: comparing to row 0, ID cert >bsnOldDefaultIdCert<
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: comparing to row 1, ID cert >bsnDefaultIdCert<
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: comparing to row 2, ID cert >cscoDefaultIdCert<
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: called to get cert for CID 183fd2b6
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: comparing to row 0, certname >bsnOldDefaultCaCert<
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: comparing to row 1, certname >bsnDefaultRootCaCert<
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: comparing to row 2, certname >bsnDefaultCaCert<
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: comparing to row 3, certname >bsnDefaultBuildCert<
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: comparing to row 4, certname >cscoDefaultNewRootCaCert<
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: comparing to row 5, certname >cscoDefaultMfgCaCert<
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: comparing to row 0, certname >bsnOldDefaultIdCert<
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: comparing to row 1, certname >bsnDefaultIdCert<
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: comparing to row 2, certname >cscoDefaultIdCert<
    *spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: called to evaluate

  • AT&T DSL Modem compatible with Airport wireless router?

    I recently switched from cable internet to at&t DSL. I connected the DSL modem directly to the computer and followed all instructions for set up (per instruction from AT&T). Now I need to connect the DSL modem directly to the airport router to get wireless, but when I do this the computer doesn't recognize any internet source. What do I need to change to make this work?
    Thanks in advance!

    "ATT tech support helped as I got it set up in BRIDGE mode so my Apple Time Capsule could be the router."
    It sounds like you set the Time Capsule up in Bridge Mode, which would mean that the 2wire was doing the routing, not the Time Capsule.
    To verify, open AirPort Utility, click Manual Setup and click on the Internet icon. Check Connection Sharing at the bottom to see how your Time Capsule is configured.
    I don't have a dual band Time Capsule, so I can't give you a good answer about whether using the TC in bridge mode would cause problems setting up the second "guest" network.
    Since each network would require an IP address and the 2wire is assigning them, there might be an issue there. This would really be a question for Apple support or perhaps another user has configured their system this way and can provide some input.

  • Switched from DSL to CABLE. WRT54G Wireless Router stopped working.

    When I switched from DSL to CABLE, my WRT54G Wireless Router stopped working. I am not able to access the router page (192.168.1.1) Also, when I use the set up CD for re-installation, the wizard aborts in the middle saying it can not connect.
    I appreciate any help to resolve this problem.
    P.S. The router acts like a one-port wired router. 

    Here is my favorite method for resetting a router to factory defaults, and trying to get it working again.
    To reset your router to factory defaults, use the following procedure:
    1) Power down all computers, the router, and the modem, and unplug them from the wall.
    2) Disconnect all wires from the router.
    3) Power up the router and allow it to fully boot (1-2 minutes).
    4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
    5) Power down the router.
    6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
    7) Power up the router and allow it to fully boot (1-2 minutes).
    8) Power up the computer (if the computer has a wireless card, make sure it is off).
    9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
    10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
    If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
    If you cannot get "Reply from ..." in step 9 above, your router is dead.
    If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
    If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
    Please let me know how things turn out for you.

  • I'm currently signed onto my home network and want to go on with another computer but don't remember my password for my network.  Does anyone know where to find this?  It's a password that I set myself, not the one that came with my router.

    I'm currently signed onto my home network and want to go on with another computer but don't remember my password for my network.  Does anyone know where to find this?  It's a password that I set myself, not the one that came with my router.

    It's in your Keychain on the computer you usually use to connect to your network - the "kind" will be "AirPort Network Password".
    Your Keychain can be opened by using the Keychain Access program. It is in your Utilities Folder.
    Open Keychain Access, and type airport in the search field. You will see a number of entries. Choose the one with the name of your wireless network, open it, and check the box next to "show password". Before it reveals itself you will be asked for your login password - the one you use to log in to your MacBook.
    The network password will appear in the box.
    Quit Keychain Access.

  • Can I set a default home page when people use my router?

    Can I set a default home page when people use my router?
    Can I set it to my web site for example so that people have to go there when they connect?
    Thanks,
    Paul

    Hello EireReality. Welcome to the Apple Discussions!
    Can I set a default home page when people use my router?
    No, at least not that I'm aware of. Setting a "default home page" is typical feature of a web browser, not an Internet router.

  • 1600 and 2600 series aps no heatmap on cisco prime 1.4.0.45

    after plotting 1600 series and 2600 series aps on the respective uploaded maps, there's NO heatmap coming out. 
    setup composed of:
    1600 series aps
    2600 series aps
    wlc running HA (7.4.121.0)
    cisco prime 1.4.0.45
    i noticed some errors from prime:
    error 1: Exception while computing Coverage Heatmap. Message: COMMON-1 Try Recompute RF Prediction - this error message shows after positioning the aps on the map and clicking save button. it took sometime to display then this error message shows. 
    error 2: Error in Recompute RF Prediction: SyntaxError:syntax error - this error shows after running recompute rf prediction option
    i tried 802.11a/n and 802.11b/g/n protocols but still no heatmap. i tried unselecting ap heatmaps option and select it again but still no heatmap.
    anybody have an idea what is going on? tia

    Hi,
    Try removing both APs from the map and saving. Next, go back into the map an assign the APs. If they still do not map then I would look at the traps on the controller and make sure that the AP is fine. I would also look at performing an on demand refresh from the controller to the WCS. You can do this from the management page in WCS.

  • Cisco aironet 2600 series AP configuration with windows 2008 R2 Radius server.

    I want to know the configuration of Cisco aironet 2600 series AP with windows 2008 R2 Radius server.  
    I have
    1. AD & DHCP Server
    2. Cisco Aironet 2600 Access Point.
    I want to connect wifi devices through this AP. Authentication should be through Radius server and AD.

    Hi , 
    Below link should support your requirement 
    http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/116584-configure-wirelesslan-00.html
    Minimal command : -
    AP(config)# aaa new-model
     AP(config)# radius-server host 172.20.0.1 auth-port 1645 acct-port 1645 key XXXXXX
     AP(config)# radius-server deadtime 10
    HTH
    Sandy

  • How to add docentry with some num.?can you solve below query   Declare @a as Numeric SET @a=14900000; SELECT (@a+($[@MAINTDCHEAD.DocEntry])as 'series no'

    how to add docentry with some num.?
    can you solve below query
    Declare @a as Numeric
    SET @a=14900000;
    SELECT (@a+($[@MAINTDCHEAD.DocEntry])as 'series no'

    Hi,
    Yes possible.
    Try this:
    Declare @a as INT
    SET @a=14900000;
    SELECT (@a+($[ORDR.DocEntry]))
    Thanks & Regards,
    Nagarajan

  • Question about setting up rdp using a cisco 800 series router

    HI there,
    I am currently in school for networking. One co-op placement I went too handed me a cisco 800 series router to practice my routing skills on. I am trying to setup RDP so I can access my server from outside my internal network. I ran this following acl command to do it.
    ip nat inside source static tcp server IP address port# cable modem IP port # extendable.
    My question here is, my cable modem will occasionally hand out a different IP since it has DCHP. I cannot turn DHCP off in my cable modem. So is there a way I can set this up to use a dynamic IP from my modem so I alwasy have access to it or every time my modem changes the IP address do I have to go in and modify this acl?

    Configure DDNS ( Dynamic DNS ) on the router. For this you need to register with a DDNS provider. Go to
    http://www.no-ip.com/ . they provide free reliable service.
    With DDNS, Once your router gets a DHCP address from your ISP , it will dynamically update the DNS name record. For example if you register you routers name as, "myrouter.no-ip.org",  from there onwards whatever the IP your router gets, you can refer to that by this name.
    So do as what Paolo said regarding using interface instead of ip, and register with the DDNS and you are good to go..
    Hope this helps
    Please rate this post if helpful..
    Thanks
    Shamal

  • Problems setting up Verizon DSL (DHCP) and AirPort Extreme

    I have Verizon DSL with DHCP and old router (Linksys WRT54G). I've bought iMac and new router (AirPort Extreme) to connect to iMac wirelessly. I have a Windows computer connected to the Linksys WRT54G. Now here is the story. I can connect verizon DSL modem (it's in bridge mode) to PC directly and connect to the Internet. When I plug AirPort between the DSL modem and PC, auto-configuration doesn't work, AirPort utility says there is problem with internet connection. Router simply can't obtain IP address from verizon's DHCP server. I've tried to copy DNS server addressed from the IP configuration in Windows, the AirPort light went green and Windows indicated connection as successful, however I still cound't browse the Internet because gateway is not set. Any ideas how to make AirPort connect to the internet using DHCP instead of manual settings? I can try to do it from the mac if needed, I don't think it would make any difference though.

    Welcome to the discussions!
    Sorry, I can't quite track exactly what you are trying to do.
    What would the network that you are trying to set up look like?
    Modem>AirPort Extreme>Computers? Are you saying that you won't be using the Linksys in the new setup?
    Sounds like you need to set the Airport Extreme up to supply PPPoE service (which the Linksys is doing now-if the modem is in bridge mode), but I will wait for your response before offering specific info.
    If you've been fiddling with settings, we may need to do a hard-reset on the AX to start over. You should not be fiddling with DNS, etc. Almost always, these settings are done automatically when you have the device set up correctly.

Maybe you are looking for

  • Font name length limitation...

    Hello all, I have a serious problem related with .PFB font files. Is there any relation between font name length; I checked and if font name length is more than 30 characters I am getting an error that "the requested file C:\....\....Pfm,C:\....\....

  • To avoid Popup Window getting minimized???

    Hi, I am opening a popup using window.open() , but when i click some where in the browser the window which is opened is getting minimized. Which should not happen . It should remain static unless the user selects a data from it. How to make the windo

  • Change Nokia 6230i settings

    Hello, I have a problem with my phone, my volume button doesn't work, so is there a way to change my volume settings using some kind of software ?

  • How to fix Import and folder-synchronize?

    Installed Lightroom 4.2 RC. Now Import and folder synchronize hang up. Uninstalled 42. RC with same result. Removed and then reinstalled 4.1 with same problem. Please advise. [email protected] Message was edited by: SD Rowdies

  • Performance issue with Preferences class in JDK1.4

    I am very excited about the new Preferences class in JDK1.4, however, my co-workers are not too thrilled about it, as the Windows implementation of it writes everything into Registry, and it is slow when we are talking about hundreds or thousands of