Setting Up AirPort Extreme for Static IP

We purchased a new AirPort Extreme about a month ago. It was very easy to set up and worked very well for all of the devices in our home, with the exception of VPN connections on our work laptops. These were incredibly slow (taking 20-30 minutes to open large spreadsheets, etc.). We talked to our ISP (4G satellite connection) about this, and they recommended going to a static IP. I have used the AirPort Utility to enter the IP address, sub net mass, router address and DNS numbers, and the AirPort indicates everything is set up properly (green status light, no errors in AirPort Utility), but it will no connect. Looking at the Internet Connection through AirPort Utility, it has all the correct numbers but the connection says "disconnected". I am able to establish an ethernet connection directly from the modem to a computer and connect with no issues. And the ISP has confirmed that the modem is working properly.
What am I missing to get the connection throughb to my AirPort Extreme?
Thanks for any help and suggestions you can provide.

Hi..
I have this same question.
Yes i did change all those and have tried with all the possible settings.
Still the problem persists..It shows all the configuration and all is right and still it is not connecting to internet.
Cross checked with the ISP, Tried same configuration in the mac machine(It's working) everything else seems to be fine but only the Airport is not connecting to the Internet.
Any solution or clarification will be appreciated.
Thanks in Advance.

Similar Messages

How to set up Airport Extreme for 11ac and 11n?

I have just purchased the new Airport Extreme (August 2014) because Apple's website states
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
I have number of Macs in my home from a new MacBook Pro with Mavericks to a Macbook Air with Snow Leopard (due to required software) and iPads.
So after setting up the new Extreme my new MacBook only accesses 11n as does my older Macs. I checked by holding down the option key while clicking the WiFi icon at the top of my Mac. Well, not so automatic then as I was expecting 11ac and 3 times faster access (as stated by Apple).
I then looked for some documentation for setting up but cannot find anything.
Hence my question here.
How to set up Airport Extreme for 11ac and 11n simultaneously?
At present the new Extreme is no better than my previous 2 year old one.
Thank you.
Michael

How to set up Airport Extreme for 11ac and 11n simultaneously?
Assuming that it is operating correctly, 802.11ac and 802.11b/g/n are broadcast simultaneously by default.
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
That is advertising. The real information is usually found in the small and hard to read footnotes:
Based on theoretical peak speeds. Actual speeds will be lower.
AirPort Extreme is based on an IEEE 802.11ac draft specification. Performance based on comparison with Apple’s 802.11n products. Comparison assumes AirPort Extreme network with 802.11ac-enabled computer. Speed and range will be less if an 802.11a/b/g product joins the network. Accessing the wireless network requires a Wi‑Fi-enabled device. Actual speed will vary based on range, connection rate, site conditions, size of network, and other factors. Range will vary with site conditions.
Since the 802.11ac signal is being broadcast only using the 5 GHz band, some users report that they have had better results by using the option to assign a different name to the 5 GHz band, and then pointing their Mac to that specific signal or network. You may want to try that option.
But first as a test, please locate the MacBook Pro about 10-15 feet or 3-4 meters from the AirPort Extreme with clear line-of-sight between the two devices. Restart both the AirPort Extreme and the Macbook Pro and then check to see if the Mac is connected to an 802.11ac signal.
If not, please power off your other wireless devices...computers, mobile devices, etc. temporarily, and try the same test again.
Please report on your results.

Hi having trouble setting my airport extreme for guests?

hi having trouble setting my airport extreme for guests?

This is likely because you have the AirPort Extreme connected to a modem/router, or gateway device.....and not a simple modem. Can you provide the make and model number of your "modem", as we previously asked?

Having trouble setting my airport extreme for guests

hi having trouble setting my airport extreme for guests?

Please see your other post on exactly the same subject.

Set Up Airport Extreme with Static IPs and DHCP same time

I have Verizon Fios to my Business with 5 Static IP Address. One of them must be assigned to the Airport Extreme Base Station. I have 5 iMacs needing internet connection of which 2 need to use a static ip,( Filemaker Server and my Mac OS X Web Server). I also use 2 iPhones with a custom App accessing that FileMaker Server via the internet too. I want to set up my Airport Extreme Base Station to have those 2 iMacs connected with static ips , which must NEVER CHANGE, via an ethernet cable and all the rest wireless with WiFi. Do to the size of my building I also want another Airport Extreme or Express to just expand the range from the Base Station for the wireless connections only. Looking at the Airport Internet Settings I only see 3 options for Connection Sharing, "Share A Public IP Address", "Distribute a range of IP addresses", "Off (Bridge Mode)". I'm thinking I need to give 1 IP Address to the Base Station, 2 ip addresses to my servers, then 1 ip address to share for my wireless DHCP connections. The additional Airport set to Off(Bridge Mode) to expand the base station. Please advise on how I would set up that base station to do this.

With respect to expanding the base stations range, in the Base stations Wireless Settings I would click to select "Allow this network to be extendeded". Then what settings would I need in the Additional Airport?
Note: Both AirPorts would have to be 802.11n models in order for this to work. The additional AirPort would need to be configured to extend the Extreme. (ref: AirPort Utility > Manual Setup > AirPort > Wireless > Wireless Mode = Extend a wireless network)
Would that NEED to be connected to the base station via ethernet cable or will it pick up the base station wirelessly?
Using the "extend" feature is intended to expand the wireless range of an AirPort with another wirelessly. You would not need to connect them by Ethernet. In this configuration, the additional AirPort would be in bridge mode and will pass through the IP information from the other base station's DHCP service.

Can I set up Airport Extreme for wireless printiing over Uverse network?

I previously had DSL, and used my Airport Extreme as my wireless router. It was in my home office, so my printer was directly plugged into the Base Station. I recently switched to ATT Uverse, which came with its own wireless router. The new router is in another room, next to the TV. My question is this: Can I set up my old AEBS to function as a wireless printing outpost, like an Airport Express, that would be connected to my office printer but accessed through the ATT network? Thanks.

Welcome to the discussions, Patrick!
Can I set up my old AEBS to function as a wireless printing outpost, like an Airport Express, that would be connected to my office printer but accessed through the ATT network?
In theory, yes. In practice, this is one of those things that you won't know until you try. Since the AEBS will have to "join" your ATT wireless network, the biggest question will be whether or not you can find a matching security setting on the AEBS for the ATT wireless network.
Are you able to get into the setup pages on the ATT router to see exactly what type of security is being used? Ideally, it will be WPA2 Personal, but different manufacturers use different names and flavors for the same thing, so it's rarely as easy as one might hope when you try to get devices from two manufacturers to talk to each other over wireless.

Setting up airport Extreme for Remote Printing

I'm leaving town and need to be able to print to our work printer (HP LJ 1320 connected via Ethernet to AirPort Extreme 802.11n).
I also want to set up our home printer (HP LJ 1022 connected to Time Capsule via USB).
I've spent hours trying everything I can think of - changed AirPort settings, have desktops sharing printers - nothing works.
I have no problem connecting to computers over the internet - using screen sharing with ease. I am at a loss as to why printing is such a problem. any help will be hugely appreciated!

I did open those ports on my AirPorts.
I've tried setting up the printers as LPD and IPP as well as HP JetDirect - Socket, but despite pointing my print jobs at these, nothing has worked yet.
Is the Airport going to act as a print server - or is that just part of the printer? Is a server even necessary? It isn't when I'm on site with either printer.
good luck with your set-up. thanks for your input.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
When Charter Tech goes to your site, have them connect the modem up, but do not connect the modem to your iMAC or MacBook Pro. What you want to do is connect the Airport Extreme to the iMac or MacBook Pro first with the Ethernet Cable. You have to do this to configure via Airport Utility to set up the Base Station Name & Base Station Password.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple Tv, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.
WHAT TO DO IF YOUR AIRPORT EXTREME WAS PREVIOUSLY SET UP FOR USE WITH ANOTHER CARRIERS ROUTER OR MODEM.
NOTE: If you already had your Airport Extreme connected for example, I previously had ATT Uverse and the Airport Extreme was connected to the Wireless Router Model 3801HGV, I disabled the Uverse Wireless and used the Airport Extreme for the Wireless signal in bridge mode, as the Airport extreme Signal is much stronger than the Uverse router, and I was able to obtain a Wireless signal with the Airport Extreme way much better with no signal loss which was very very frustrating with the Uverse router.
Anyhow if you had it hooked up like this, now that you will be using it with the Charter ARRIS Modem TM902A, you will need to reset the Airport Extreme to clear out the old data it has in memory, with the previous set up otherwise it will not work. Trust me I spent 6 hours trying to make it work reading all Apple Support Community questions and answers relating to this type issue/problem others have been having trying to get their set up working. I tried all the tips, and I finally decided just to see if by chance I would be able to connect with someone with Charter Tech support who might be familiar with Apple to be able to assist me and by luck I did. He told me why it was not working and was all due the previous configuration with the ATT Uverse router was still in memory with the Airport Extreme. Finally it was 10:30 PM when I decided to call Charter Tech Support and I had been working on this since 3:00 pm pacific. I did not call them earlier as all the post I read said they never received any good help from Charter. After calling them I finished up by 11:00 PM and was able to finally connect Apple Tv, iMac, iPhones and Macbook Pro. We love our Apple Product and Happy all is connected with the new
Internet Provider Charter. I must say the speed is way way much better than it ever was with AT&T Uverse.
THIS IS WHAT YOU WILL NEED TO DO:
First you will need to unplug the Airport Extreme, then by taking the tip of a pen or paper clip end you need to push the reset button on the back of the Airport Extreme and hold it
down and at the same time plug the power cord back into the Airport Extreme count to 5 or 10 then release the reset button. Then once he light in front of the Airport Extreme stops blinking you need to plug the Ethernet cable from the Airport Extreme to your iMAC or Macbook Pro, and restart which ever one you have, then open the Airport Utility once it is back up. If you see airport extreme pop up with the old network name or it shows and yellow triangle click on the Airport Extreme ICON it will not let you configure it but will ask if you want to get rid of it or remove and just do it. Then Again restart your iMAC or MacBook Pro, open up Airport Utility again, and on the top left you should see under “Other Airport Base Stations” the MAC ID for the Airport Extreme.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple TV, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.

I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
I have a Linksys WRT320N I used for the initial Charter setup.
I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
Hasn't caused any issues so far but one thing I did notice.
On the Linksys there were 3 DNS servers listed.
The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
I tried everything above, but light on modem still flashes yellow.
I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

Setting up airport extremes with mobile netbook cart

I work in a school environment, running windows. We have four mobile carts in the high school. We have an airport extreme for each of the carts. In our situation, the airport extremes are mobile. They do not stay in one location all the time. The teachers connect the airports to a wired connection in their classrooms. We have the netbooks set up to automatically connect to an airport when in range. I have each of the airports setup the same way; create a wireless network, each has it's own network name, radio mode is automatic, channel selection is automatic. Internet options are connect using ethernet, connection sharing is off (bridge mode) and tcp/ip is static. There are a couple of issues we seem to be having. One is that the airport with the stronger signal is not always the one the netbook connects to. I could have one classroom of netbooks connecting to an airport that is located two classrooms down the hall when there is airport in the classroom that has a stronger signal. What could be causing this? We push out settings to the netbooks via group policy, such as redirected desktop and network shares. When a user logs in they don't seem to get the whole policy all of the time. If you restart or logoff then login, the netbook gets the policy correctly. Could this be a problem when multiple airports are in range of the netbook trying to access the network? Is having the airports mobile, moving from one room to the next, a bad idea? Thanks for the help.

tried this but it didnt work that well, the distance between the main airport and the extenders is too long. Also, when choosing extending, it came bugging me with incorrect dhcp settings. Couldn't solve that.
So i configured allt he extremes with creating a wireless network, same ssid and same wpa settings. Als bridgedsetting is disabled.
That seems to work. Anyone with an opinion about this configuration?

My home network has an Airport Extreme w/Time Capsule as the base and then an Airport Express and a second Airport Extreme to reach different areas of the house. Is there a way to use the second Airport Extreme for file storage on this network?

My home network has an Airport Extreme w/Time Capsule as the base and then an Airport Express and a second Airport Extreme to reach different areas of the house. Is there a way to use the second Airport Extreme for file storage on this network? Network is administered through an iMac running OS X Yosemite 10.10.2. Ideally, would like for the second Airport Extreme hard drive to appear on the list of devices in the Finder window.

Ok.. gottcha
The problem is network wise.. Yosemite is about equal to tin cans and string.. pathetic.
Here is my usual set of instructions to get anything working on Yosemite.
The best way to fix problems is a full factory reset of all the AE in the network.
Factory reset universal
Power off the AE.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the AE to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
Then redo the setup from the computer with Yosemite.
1. Use very short names.. NOT APPLE RECOMMENDED names. No spaces and pure alphanumerics.
eg AEgen5 and AEwifi for basestation and wireless respectively.
Even better if the issue is more wireless use AE24ghz and AE5ghz with fixed channels as this also seems to help stop the nonsense.
2. Use all passwords that also comply but can be a bit longer. ie 8-20 characters mixed case and numbers.. no non-alphanumerics.
3. Ensure the AE always takes the same IP address.. this is not a problem for AE which is router.. it is a problem for AE which is bridged.. you will need to set static IP in the main router by dhcp reservations or use static IP in the AE which is tricky.
4. Check your share name on the computer is not changing.. make sure it also complies with the above.. short no spaces and pure alphanumeric..
5. Make sure IPv6 is set to link-local only in the computer. For example wireless open the network preferences, wireless and advanced / TCP/IP.. and fix the IPv6. to link-local only.
6. Now mount the disk of the second AE in finder... manually.
Use Go, Connect to Server and type in the AE ip address.
SMB://10.0.1.2
Where you will replace that address with the actual address. The network resource should be discovered and then it will request the password.. type that in and make sure you tick to save it in your keychain.
There is a lot more jiggery pokery you can try but the above is a good start.. if you find it still unreliable.. don't be surprised.
Do as much as you want of the above... not all of it is necessary.. only if you want it reliable.. or as reliable as Yosemite in its current incarnation can manage.
The most important thing is point 6.. mount the disk using direct IP address and not names.. dns in Yosemite is fatally flawed.
See http://arstechnica.com/apple/2015/01/why-dns-in-os-x-10-10-is-broken-and-what-yo u-can-do-to-fix-it/

AirPort Extreme with Static IP unable to connect to internet

I have a business internet account and static IP addresses. I just purchased a new AirPort yesterday and after setting it up with the static info, I am unable to connect to the internet. My other clients on the network can connect to each other but not to the internet. I tired pinging the IP address and that was successful but when I tried to ping the Gateway / Router address, that was not. When I plug my computer directly into the cable modem I can connect to the internet. The funny thing is that when I pull up my network settings and look at the IP address that the Ethernet connection is showing, they are nothing like the addresses that Cox gave to me. I am assuming that this problem is on their end and not my end but since I am new to this type of networking I wanted to see if there is possibly something I am doing wrong before I get them on the phone again.

Welcome to the discussions!
You may have already done this, but it was not mentioned in your post. Your cable modem may be "remembering" your computer. In order for it to connect correctly to a new device, you must always reset and power down the cable modem for a period of time.
Some newer modems will reset in a few minutes, some take 15-30 minutes and some older devices on older cable system may require 4-6 hours or more to fully reset the equipment back at the service provider.
If you haven't done this yet, try pushing the reset button on the modem and then power it off and let it rest for 15-20 minutes. Power off the rest of the network as well.
Power up the modem first and let it run a few moments, then power up the AirPort Extreme for a few minutes, then your devices one by one. If your settings are correct on the AEBS, that should get you connected to the internet.
Message was edited by: Bob Timmons

How do I set up Airport Extreme with cable modem and router?

Hi--
I'm having a house built and all of the wiring for TV, phone, and internet will be centralized in a closet. The cable modem can be placed there as well. In one room in the basement I want to use my Airport Extreme for my iMac and USB external hard drives. In another location of the basement, I'd like to set up a Time Capsule for another desktop and USB printer. If the cat5e comes out of the wall at each location, I "think" I need a router at the closet location. I also thought I might need an Airport Express upstairs on first or second floor to boost signal for my laptop. The house isn't that big so maybe that's overkill. So beyond the router question, do I want to set up a roaming network and have the Airport Express connected via ethernet or just wireless if the thought is that I need this? Finally, if I should connect cable modem to router to Airport Extreme, Time Capsule, etc., in what order and ports does the equipment get connected? Many thanks!!

Welcome to the discussions, Forum Girl!
It would be best to position the cable modem and main router in the central location like the closet if possible. The other devices would connect via ethernet to the wall jacks in each room.
If you could setup a "roaming" wireless network as you mention, this will give you better wireless performance and coverage. This is the way commercial establishments like airports, businesses, etc. are configured for wireless.
The order of connection would go something like this: ethernet connection > cable modem >main router>devices. Devices could be computers, routers, a backup device, etc. Since the Extreme has only 3 LAN ports for ethernet connections, you will also need to plan to install an "ethernet switch" near the location of the main router to provide enough ethernet jacks. If you are planning to use DirectTV, etc or your audio/video devices require ethernet connections (most new products do for updates and extra features), be sure to plan for that as well.
Make sure that CAT5e or CAT6 wiring is run so you will be able to take advantage of faster gigabit speeds.
Finally, it would be a good idea to work with an IT specialist to go over your plans to make sure all the bases are covered. This would be money well spent.

Can I use the Time Capsule strictly for system backup and continue to use my Airport Extreme for all my wireless needs

I want to use the Apple Time Capsule as an external drive and continue to use my Airport Extreme for all my wireless needs. Can I do that? The reason I ask is that my Time Machine utility cannot find the TIme Capsule - it only shows me the Airport Extreme, even when I "Rescan". SO I am unable to use the Time Capsule.

You will need to connect an Ethernet cable from one of the LAN <-> ports on the AirPort Extreme to the WAN "O" port on the Time Capsule.
Perform a "hard reset" on the Time Capsule by holding in the reset button for 9-10 seconds, then give it another minute to restart to a slow, blinking amber light.
Open AirPort Utility, select the Time Capsule, and click Manual Setup
Click the Time Capsule tab located below the row of icons to assign a name to the Time Capsule, a device password, and adjust Time Zone settings.
Next, click the Wireless tab located to the right of the Time Capsule tab
Change the setting for Wireless Mode to Off
Click the Internet icon, then click the Internet Connection tab
Connect Using = Ethernet
Connection Sharing = Off (Bridge Mode)
Click Update at the lower right to save the settings and allow 30 seconds for the Time Capsule to restart to a green light.
You are all set

Set the Airport Extreme to not broadcast the SSID

Set the Airport Extreme to not broadcast the SSID

"Hiding" the SSID will do nothing to protect you from hackers.....and anyone else who wants to see your network, since there a numerous free utilities on the Internet that will reveal your network in seconds.
On the other hand, it might keep a few honest neighbors from seeing the name of your wireless network.
iOS devices often have trouble connecting to a "hidden" network, so you may need to display the network if your iPhone, iPad, etc have trouble connecting to the network.
Your call on this.
Assuming that you have Lion, Mountain Lion or Mavericks on your MacBook Pro.....
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the AirPort Extreme icon, then click Edit in the smaller window
Click the Wireless tab at the top of the next window
Click Wireless Options at the bottom of the window
Enter a check mark in the box next to Create Hidden Network
Click Save, then click Update and allow a full minute for the AirPort Extreme to restart

Is Internet Explorer incompatible with Airport Extreme for connecting wirelessly to the Internet?

repeat -is Internet Explorer incompatible with Airport Extreme for connecting to the Internet- I am trying to hook up my sister's / Windows 7...HP mini computer to my wireless connection (Airport Extreme to cable /BrightHouse ) all I get is -failed due to 'error 651' -am about to call the jockeys at the cable company to see if they have work-around. Any comment appreciate. Thanks./jimiros

Diane,
I have added very few apps to my G5. The majority of my time is spent editing photos with PhotoshopCS3. I have software updates set to run weekly and have always kept them up to date. I really believe it's a disk permissions issue...but repairing them doesn't help.
*+Upon installation, I used Archive and Install.+* While I agree that Erase and Install may sound like a good idea, it makes me nervous. I do have everything backed up on a bootable CMS drive, but I'm a photographer and was hoping to not have to erase the G5.
Yes, as I mentioned in the original post, I've downloaded and installed the Airport firmware update. And all software is up to date.
All was working just dandy before the upgrade. Unfortunately now it's sounding like I may have to erase my hard drive and install fresh.
If I do that, is it just a matter then of dragging my photos from the backup disk to the G5? And documents? Etc?? The thought of getting all my photos and important information back on the G5 seems a bit staggering.

Setting Up AirPort Extreme for Static IP

Similar Messages

Maybe you are looking for