Setting up ip camera with HH5 infinity
Am having problem trying to set up a tenvis JPT3815W IP CAMERA,
I am able to access it on my home network but not from a remote location would appreciate any help in resolving this problem.
These pages should help.
Port forwarding problems
CCTV and IP cameras - port forwarding
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.
Similar Messages
-
How to set up time capsule with BT Infinity
how to set up time capsule with BT Infinity
The easiest and sure way is to use bridge on the TC as the method of connection. The TC then becomes a device in your network and gets its IP from the main router that I presume BT supply.
Method is,
1. Plug the TC WAN port into the BT supplied modem by ethernet.
2. Plug the computer you are using for the setup into the TC by ethernet.
3. Run the airport utility .. go to internet tab on the top menu..
In the bottom option, Connection Sharing choose off (bridged mode)
4. Go to the wireless page and setup wireless connection as you like it.. using whichever band you want. And make sure security is set to the highest setting, wpa2 personal. Put in a decent wireless passkey.
5. Press the update and fix whatever else the TC will show as needing fixing.. usually security stuff.
6. You can then disconnect the ethernet and connect by wireless if you want. Any port on the TC will now be a LAN port, including WAN.
This is assuming BT supply a wireless router with built in vdsl/other type of modem. If so you normally will not be able to bridge the modem, unless BT are using pppoe authentication which they haven't in the past.
If you really need to use the TC as a router then you will need to work out an alternative method. You can double NAT by placing the TC in the DMZ of the BT router if that is an option. It is not without issues in general. -
Setting up video camera with iDVD
I am very new to iDVD so please forgive me. I have read the manuals and what they don't tell you is how you go about linking up your video camera with your mac.
I have an old Mini DV JVC video camera (one of the first digital cameras available). Do I need to buy some sort of cable to link it to my iBook (as it only has audio and video cables and scart adpater). Also, do I need some extra software in order to import footage to my iBook from the mini DVs on my camera to allow me to use the files in iDVD?
Sorry if this is a stupid question but I no longer have my video camera handbook.Sparkley,
Try going to JVC's website, and see if you can get a new manual.
Odds are you need a firewire cable, and many camcorders do not come with them. Most use a 4 pin to 6 pin firewire (also called 1394 or iLink) cable. Be sure NOT to get a USB cable, it won't work.
Check and see if there is a small port labeled "DV" on the JVC somewhere.
As long as your camera is "DV", you should need any other hardware (besides the cable) or software outside of iLife (iMovie/iDVD). I recommend that you use iMovie to start for importing - I'm not a fan of "OneStep" in iDVD.
Read this too:
http://docs.info.apple.com/article.html?artnum=165336
john -
Trouble setting up wireless cameras with airport extreme
I am trying to set up my alarm dot com wireless cameras and am having trouble getting them to connect to my Airport Extreme. With my prior D-Link router, there was no issue, but since upgrading to the Extreme, I can get them to locate the network, but not connect.
Add me to the list of people with Netgear DM111P ADSL modem and AEBS(n)...I can connect fine to the internet directly from MB Pro to modem, and for the last couple months have used the Netgear with my trusty AEX, no problem.
Now I finally get my AEBS from Canada (here in Dubai, UAE) and I have wasted hours trying to get on the internet with the AEBS. I have it configured exactly the same as the AEX is! One works fine, the other not at all. Exasperating.
I am using the Netgear with PPPoA Bridging (the correct setting for the ISP here and what works with the AEX and direct connection). The AEBS shows it is getting the IP correctly and has a solid green light. My MB Pro shows it is getting an IP from the AEBS's DHCP server. And shows entries for the DNS servers.
Yet..no internet. From the number of complaints with this exact same setup...it ain't me...I have used and configured over a dozen routers and modems from all major manufacturers, used DSL/ADSL/cable, PPPoe, PPPoA, etc etc...and I'm stumped.
This is NOT a typical Mac product. I am not happy. If someone figures this out, you will have my admiration. -
I'm currently signed onto my home network and want to go on with another computer but don't remember my password for my network. Does anyone know where to find this? It's a password that I set myself, not the one that came with my router.
It's in your Keychain on the computer you usually use to connect to your network - the "kind" will be "AirPort Network Password".
Your Keychain can be opened by using the Keychain Access program. It is in your Utilities Folder.
Open Keychain Access, and type airport in the search field. You will see a number of entries. Choose the one with the name of your wireless network, open it, and check the box next to "show password". Before it reveals itself you will be asked for your login password - the one you use to log in to your MacBook.
The network password will appear in the box.
Quit Keychain Access. -
Capture no longer working on HDV camera with HDV setting - only with NTSC.
I have a Canon HV10 HDV camcorder. It was working fine with HDV 1080i60 settings in Easy Setup last week. Now FCP wont see this camera with these settings or HDV 1080i60 Firewire Basic. It will only see it with standard NTSC DV set.
I have been doing some captures with my Sony TRV-900 DV camera since the HV10 was last used. Did this somehow mess something up? I have tried switching it a few times in Easy Setup and it only works with DV NTSC. Anyone with any ideas?
Thank you!My bad. I accidentally switched the output of my camera to DV instead of HDV sometime last week and forgot. It works now.
-
How do I set up WRT54G router with 4 computers and WVC54GC Wireless Camera
Can anyone please tell me how to set up my Home Network with full security turned on?
I have at least 4 neighbors that show up on my wireless connections list. I have a daughter that loves music and is constantly downloading viruses but only on one wireless connection. The rest of us want to be protected from that computer. My system consists of the following:
One Linksys WRT54G Router
Two Linksys WMP54G Wireless PCI adapters,
Two Linksys WVC54GC Wireless Cameras (Possibility four if the 1st two ever work OK.)
Two Linksys LNE100TX PCI Ethernet Cards,
One HP Ethernet Printer
Three computers were connected by Ethernet cable and one was wireless. I did not change the admin password and I thought everything was working fine for a couple of years until I found that the wireless computer was acting as a “drone” and slowing everything down to a snails pace. It could even turn itself on.
I changed one of the Ethernet computers to wireless and decided that it might be time to also change the password and increase security. Setting up security completely shutdown the wireless drone computer. I was OK with that, at least until I can reformat that harddrive.
I then decided while I was at it, I would add a wireless camera (WVC54GC). I set it up using the software and Ethernet cable that came with it. After 6 tries I finally got the camera to work with the cable attached, but it does not work wireless and now none of the other computers connect any more. Is there a limit on how many connections? Should I reset the router and if so, do I disconnect the DSL modem? I’m afraid of the “drone” computer because I found some very bad malware on it. One in particular caused me to replace a hard drive.
I’ve read page after page of network stuff on the Internet and I guess I just don’t know how to ask the right questions. I’m tired of fooling with this.hi , when u talk about security , are u referring to the "viruses" your daughters PC may be propogating to the rest of the network , or are u referring to external attacks on the router or your wireless PC"s ???
In case u are referring to the "virus" attacks , the best you can do is install a good antivirus software on all PC"s and keep the virus definations updated....
In case u are referring to the wireless security , i'd suggest that your use WPA2 personal. you can select WPA2 by going to the "wireless security" option.
let me know if u need anything more. -
Setting up a document camera with Automator
Here's my setup:
I have a document camera stand, tripod, clamp light, all that. My goal is to be able to set a document on the stand, run an Automator script (or AppleScript) and have an image of the document saved as a PDF in a desired folder.
I think I can handle the scripting. My questions:
1) Should I use the "take picture" command in Image Capture? Or a different command in a different bit of software?
2) Is there a list of the current digital cameras that can be controlled via USB in this way? (Extra points if it's a video camera with an image capture option.)
Thanks in advance.
G5 tower Mac OS X (10.4.6)I had a chat with someone from Linksys last night. And they told me that the router was working fine as shown in the screenshots, and I know it works fine on the home network.
He said the problem is that it is behind another router, like you guys pointed out. He said that I need a public IP address and that I need to connect the WRT1600AC directly to the modem.
The problem is that my ISP only gives out the Router/Modem combo piece of **bleep** by Cisco. I think most ISPs these days here in Canada give out those Router/Modem combos.
So the router/modem that my ISP gave me is this one: Cisco DPC3825
Now I have the Linsys router connected to this junk and I don't know if there is anything I can change in the settings to have my IP camera work with the Linksys router or If I will need to buy a separate modem.
I connected my IP camera back to the Router/Modem combo that my ISP gave. The camera is working again, but I wanted it to go through the Linksys router that it would show up in the router settings along with other devices. -
How to set properties for HTTPClient came with WSClient_extends.jar ?
In my web service client application, we need cookie to maintain session between server and client.
I think the server cookie policy is not completely standards compliant since HTTP request to this server through Apache HTTPClient need to setup following:
"http.protocol.single-cookie-header" to be true
cookie policy to be "CookiePolicy.BROWSER_COMPATIBILITY"
My problem is, we are using Oracle WSClient_extends.jar for web service call, WSClient_extends.jar came with it own HTTPClient implemetation.
Are there equlivant properties can be set in Oracle HTTPClient similar to Apache HTTPClient to handle such cookie policy?
ThanksHi,
This is correct; see my blog entry: http://db360.blogspot.com/2007/01/is-your-java-application-failoverproof.html
However, you need to use oracle.jdbc.pool.OracleDataSource and from what i know Websphere does not (yet?) allow bypassing its own connection pool in favor of Oracle driver's embedded conection pool.
Kuassi http://db360.blogspot.com -
Hello
I have a macbook pro 2011 13" that came with OS Lion (integrated not on a disk). I recently bought OS Mountain Lion of the app store and it is working fine. However I was a bit dissapointed in the battery so I decided to try and downgrade and completely failed, I froze the computer and when I restarted it it did not work. I went into recovery system and erased my disk and all that and went to re-download my OS. I was expecting to get the option to re-download Lion but instead I could only re-download Mountain Lion.
My question is since my computer originally came with Lion can I reset my computer so I get OS Lion back instead of OS Mountain Lion?
Thanks for any help. Any answer will be appreciated even if it is saying it is not possible.Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Erase the hard drive:
1. Select Disk Utility from the main menu and click on the Continue button.
2. After DU loads select your startup volume (usually Macintosh HD) from the left side list. Click on the Erase tab in the DU main window.
3. Set the format type to Mac OS Extended (Journaled.) Click on the Erase button and wait until the process has completed.
4. Quit DU and return to the main menu.
Reinstall Lion: Select Reinstall Lion and click on the Install button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
Kappy, a pretty wonderful and very knowledgeable man, has tip for that which I have copied and pasted above -
I have Itunes set up to sync with my Ipod touch and Ipad. As of today, iTunes has started searching to sync with an iPhone, which I don't have and pops open with an error message stating it cannot locate the iPhone to sync. I have looked in devices and only the iPad and iPod Touch are listed. Any ideas on how to stop iTunes from searching for any iPhone it is never going to find? It is annoying to have it popping up all the time with the error message. Thanks in advance for any suggestions.
You should really read the manual.
"How do you restore from backup? "
Restore. When given the choice, choose to use backup.
"And how can I check to see if the pics and videos are on my computer somewhere first??"
They would only be where you put them. What program did you use to import them? Pics/vids taken with ipod are not part of the sync process at all. You should be importing them just as you would with any digital camera.
If you did not import them, then they are not on your computer. -
Help. I recently bought a 2008 Mac Pro from Mac of all Trades. It came with Leopard 10.5 installed. When I set initially started the computer, I followed the instructions on the screen. I was asked to set up a password which I did. Since I'm very forgetful and not too tech savy, I wrote it down as I typed it in. I first went to install Office Mac 2011 but when it asks for a password, it won't accept the one I set up. I was told that if I bought the new Snow Leopard 10.6.3 and installed it, that it would reset everything. Well, it won't allow me to load it without the password. I am new to Apple - this is my first. I have always been able to "reboot" a computer with discs but I'm not sure how to do this one. Is there a way to do it without the password and reset everything? Could somone please email me
Thank You. David Moore
<Email Edited by Host>If you don't have original install disks for your Mac, you can order replacements disks directly from Apple at a nominal cost. The original install DVDs are required to reset the password.
If you have no data on your drive that you want to keep, you can boot up from the OSX Snow Leopard disk and install OSX SL.
Insert the Snow Leopard DVD and hold the C key during startup. The Mac should boot from the CD/DVD drive into the installer.
Follow the prompts, erase the disk and install OSX Snow Leopard. -
How can I use the built-in Isight camera with an external camera (usb/firewire) at the same time?
How can I use the built-in Isight camera and an external video camera at the same time?
I'm wanting to stream over Oovoo/Skype/etc. using 2 cameras.
ThanksSimple question with a not so simple answer.
(a) If you mean that you want to run multiple apps simultaneously using a different camera with each app, you may encounter computing power limitations. Digital video is processor intensive. The only way to know if your Mac can do this it to try it. If the video does not work together but each app works when it it the only app running, you are likely overloading your Mac's ability to process and/or move all the required data in your data bus. You can get a better indication of whether this is the case by watching your Activity Monitor utility while running the apps you want to use.
(b) If you mean that you want to have more than one compatible camera connected to your Mac simultaneously for ease of changing between video sources, some, but not necessarily all, apps you are using to operate your camera(s) allow you to select between your cameras.
How you select among connected cameras depends on which application you are using. Here is how camera selection works in a few examples:
(1) For iChat, you can choose which iSight you use in the "Camera:" choices bar in iChat > Preferences... > Audio/Video that appears when more than one compatible camera is connected. Although your camera choices will be different, the choices bar will look something similar to the Preferences settings shown here:
If you cannot see the "Camera" choices bar, your Mac is recognizing only one (or none) of your cameras. In that case, consider the suggestions fromhttp://support.apple.com/kb/HT2090 for iSight problems or refer to your other camera's documentation for help.
This particular choices bar solution applies ONLY to iChat. Most other applications also have settings that allow you to choose which camera to use. However, they do not all work the same way.
(2) For instance, iMovie HD's camera choice is NOT set via Preferences. When you have more than one compatible camera connected, iMovie6 HD uses a drop-down menu choice something like this (depending on which version of iMovie you use):
Note: Because I had no built-in iSight connected when I made this example, and because my external iSight was not connected, the drop-down menu showed only "Time Lapse." Because your Mac has a built-in iSight, your built-in iSight would show in the drop-down menu even when no other camera is connected. Connecting an additional Mac compatible webcam should allow you to choose either camera.
Other iMovie versions work slightly differently.
iMovie 9 (from iLife '11) uses a different camera choice button shown in this article:
http://docs.info.apple.com/article.html?path=iMovie/9.0/en/mov39f84285.html
iMovie 8 (from iLife '09) is slightly different as explained in this article:
http://docs.info.apple.com/article.html?path=iMovie/8.0/en/10172.html
In general, you can use your Mac's help for the application in use to find out how to select among more than one connected camera.
(3) Photo Booth in Snow Leopard 10.6.x and later uses the Photo Booth > Camera menu command to select which camera to use.
Note for readers with older Mac OS X: The previous version of Photo Booth that came with Tiger (10.4.x) is such a simple, basic app that it offers no menu selectable choice. Unless your built-in iSight is already occupied as the camera being used by some open application before you launch Photo Booth, Photo Booth will use ONLY your built-in iSight.
However, you can use the trick from ¶ 4 of http://docs.info.apple.com/article.html?artnum=302781 to let Photo Booth use an external camera.
(If you have an external Firewire camera connected, it may be used in preference to any USB webcam. If that is a problem for you, merely disconnect the problem Firewire device.)
(4) For FaceTime, launch the app and click the Video menu item.
If your Mac recognizes more than one connected compatible camera, a "Camera" section listing the cameras from which you can choose will appear there. Clicking on the desired camera name will let you select the one you want as shown in this image from my Mac Pro and LED Cinema Display:
If your Mac recognizes only one compatible camera, the "Camera" section will not appear in the Video menu, but FaceTime will automatically use the connected camera that is recognized by OS X.
(5) I do not use Skype oir Oovoo. For those or other apps, see Help for each app for info on how to select your desired camera.
Message was edited by: EZ Jim -
I have a pioneer 50 inch plasma + I purchased new from the company back in 2005. I tried to hook up an Apple Tv to the pioneer receiver that came with the TV. I can not get it to work.
The receiver has two HDMI inputs in the back. However they say they are not for PC's. Furthermore they must be set up by going to the home menu. I tried everything, but I can not get the receiver to talk to the Apple TV. I even tried a connector that uses an HDMI to the Apple TV that has the other side of the cable as 5 RCA cables. I could not get the receiver to see the Apple TV. I have a newer TV in the house, it has no problem talking with the Apple TV. But this older system seems to be handicapped in its ability to talk with the newer Apple TV system.
My Email is [email protected]
Do you have any suggestions
Thanks
BobI could not access the Apple TV on the television. If I put the Apple TV directly into by TV, I have an external sound system (entertainment system), therefore I worry that I would by pass the audio.
Thanks for taking your time to attempt to help! Any more suggestions would be greatly appreciated.
Bob -
Is there a way to enable 3D display outside of the software that came with the device?
Hello,
I just bought this device and my primary use for it is the 3D function, but unfortunately there is no option to enable or disable the 3D function outside the set of software that came with it. For example in Cyberlink Power DVD 3D works fine, TriDef software creates depth from games but that is not actually what I need. I need just to have an image or a sequence in standar over-under or side-by-side formats and to enable the 3D effect on the display.
Some third party software, Stereoscopic player for example recognizes the monitor fine and displays the 3D content normally. But what I need is to display a full screen image from After Effects so I could have a live preview of the 3D, is there a way to somehow engage the 3D mode by some utility or driver?MHetlerovic, welcome to the forum.
I read the manual thoroughly and it doesn't appear that there is any way to access the 3D mode without using some type of program.
Please click the "Thumbs up + button" if I have helped you and click "Accept as Solution" if your problem is solved.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee.
Maybe you are looking for
-
Why does my battery die so quickly after updating to iOS 6.0.2 on the iPhone 5!?
Is there a fix to this or do we have to wait for the next update? My iPhone has become a useless 2-hour-running brick in my pocket...
-
Hi, I have a problem with using the "java.util.ZipFile" library. Imagine that I have a zip file containing text files with names including french accents. The code to open and extract the files is simple : - I get each "ZipEntry"; - get an InputStrea
-
I don't seem to have an align/unalign check box option anymore for tools like the clone and healing brush. PS CC14 Anyone know how to get it back?
-
Can i use java to change the names of directories, or use it to make new directories, move files to directories, etc? Thanks. Lawrence Lu
-
Itunes update stopped and now can't open
I downloaded the latest version of itunes and whilst in the middle it stopped (not sure if this may have been my fault!!). Anyway itunes won't open. I've tried reinstalling and when i do so it doesn't work as it says i need to be logged in as an admi