Setting up PCI-DNET card to work with Eurotherm 2404 Controller w/Device Net

I have installed the NI PCI-DNET card in my PC running W2000 and the NI Measurement and Automation Explorer. I have also wired from the PC Card to a Eurotherm 2404 Controller with a Device Net Module and have terminated the connection with a 120 Ohm termination resistor. The baud rate and address have been configured on both ends to match, however although I am getting a good connection to the board I am not able to pick up the device when I run the "Simple Who" funtion. Any advice would be greatly appreciated.
Thank You

Hi,
When you say “…address have been configured on both ends to match”, do
you mean that you set the ‘Interface MAC ID’ of the dialog that comes
up when you start Simple Who to the one that is used by the Eurotherm
2404 Controller?
Simple Who is a master/scanner in a DeviceNet network, thus the
‘Interface MAC ID’ you configure is the one of the master, which must
not be identical to the one of any slave devices in the network. So,
try setting the ‘Interface MAC ID’ to a value other than the one used
by the Eurotherm 2404 Controller.
-B2k

Similar Messages

How do I set up a PCI-DNET card as master with A-B DNI as slave?

I'm trying to communicate with an Allen Bradley PLC through DeviceNet. I have a NI PCI-DNet card in my computer, and an Allen-Bradley 1761-NET-DNI interface between my PLC and the DeviceNet network. Does anyone know how to set up my National Instruments card as the Master of my PLC/DNI combination? Thanks in advance for the help.
Mark

Hi Mark:
The PCI-DNET card should set itself up as the master by default. As a matter of fact it should take more work to get it be the slave than to get it to be the master. Is this not what you are experiencing? Is there some sort of Allen-Bradley software that you have installed that is not allowing the NI board to be the master?
The DNET Manual states on page 4-8 that NI-DNET assumes that it is the only master in your DeviceNet system.
Emilie S.

Any PCIe USB cards that work with Yosemite?

I have a late 2012 MacPro currently running OSX 10.10 (Yosemite). I search for a PCIe card with a minimum of 4 USB ports what will work with this system (most I've found online so far indicate "incompatible with Yosemite"). Anyone aware of a card out there that does work? I am not connecting hard drives to the card so speed is not an issue (the card could be USB 2 or 3).
Thanks,
Carl

I've been using one of these
<http://www.sonnettech.com/product/allegro_express_usb.html>
for years in my 2008 Mac Pro. USB 2.0
Works fine with Yosemite.
(Don't worry about the big power connector on the card. It's not used for a Mac.)

G5 Dual Core 10.4 - Finally a PCIe eSATA card that works!

Happy Holidays!
I recently posted a few queries/complaints about FirmTek's PCIe cards used in an older Dual Core 2.0. Unfortunately my personal experience has not been a good one. Poor communication and initial refusal of RMA; the list is lengthy. After months of tedious thorough testing, I can only conclude the drivers on their web site, are incompatible with 10.4.11. But thanx to OWC, and DAT Optic, I finally found a PCIe eSATA card that works. In fact I'm using a DAT Optic 2 port card and 4 port card in total harmony with each other.
In my opinion, the SeriTek 2ME4-E-4 design emphasis was probably geared more toward use in a Mac Pro with 10.5 and above. After two system formats, and the failure of two different FirmTek PCIe cards, that was enough for me.
Final success came with; http://eshop.macsales.com/item/DAT+Optic/ESATAPCIE21B/ (and) http://eshop.macsales.com/item/DAT%20Optic/ESATAPCIE8/
One BIG advantage with DAT Optic are the numerous readily available drivers directly from the Silicon Image web site. And their tech support is first class.
All of this is good news for users of older Power Mac G5's.
Enjoy!
Mike

Hi Chris
Whatever the situation was with 10.4.10, or 10.4.11, I had to conclude that FirmTek's drivers were not doing the job for 10.4.11 - The condescending technician was basically ignoring my remark that this card just doesn't work with my set up. Neither could their 2 port card work.
I had to argue my point repeatedly, (shouldn't have to do that).
In any event, I'm rolling pretty good with these 2 bay OWC clearance eSATA enclosures, (got 4 of them). No bridge, just good ole eSATA connections. Sure took long enough to get to this place.
Happy Holidays
Mike

Need hardware drivers (Only!) for NI PCI-DNET card, P/N 184726E-11. Do not need Labview run-time, Silverlight etc.

I need to install just the Windows XP hardware device drivers for my PCI-DNET card, P/N 184726E-11. Ordered under P/N 777358-01, the card is boxed with an installation CD-ROM. CD-ROM is NI-DNET for windows Ver 1.6.7. When the install app runs, it is trying to install all sorts of stuff I do not need - Labview Runtime, Microsoft Silverlight, Development Support, Automatic Updaters, etc. This card is being installed in a "production" machine. We have our own software, already developed, that talks to the card via the O/S. The hardware/device drivers are most certainly on the CD-ROM, I just need them identified and instructions for installing them.
Thanks,
Ed

Thank yor for the reply. However, it is not what I am looking for. The suggested download is 406MB. That's everything but MS Silverlight and the kitchen sink - overkill for our needs. We only need to install the Windows system driver for the card. We do not need Labview RT and the other development/support stuff for this installation. We have our own communications software that talks directly to the hardware, via the windows system driver. I have the 1.6.7 software CD-ROM, and need to know where the Windows sytem hardware driver/driver installer is located and what is the preferred method for installing only the hardware driver.
Thanks,
Ed.

I bought this iPhone from Apple Retail Store for the full amount, but it does not work with my SIM card only works with AT&T

Hello,
I have an iPhone 4S 32Gb White AT&T, product part No. MC921LL/A, Serial No. C39GMLPWDTDC
I bought this iPhone from Apple Retail Store (from Fifth Avenue, NY) for the full amount. Now it does not work with my SIM card only works with AT&T. I restored the phone several times, but I have not received "Congratulations your iPhone has been unlocked". Please activate my iPhone to work with different SIM cards
Thanks,
Best Wishes

When did you buy it?
Apple did not begin selling an unlocked version of the iPhone 4S in the US until 11/11/11. I believe it went on sale only through the online store at that time. I'm not sure if it's available at retail yet.
What you purchased was a phone without a contract commitment. It is still locked to AT&T. AT&T will NOT unlock iPhones for any reason. Return it and get your money back, then use that to purchase an unlocked phone.

Someone recommend a card to work with VirtualDJ & my djm

I want a sound card that will, with minimum hassle, work with Virtual DJ and a DJM-400. It has to support running two channel sound into my mixer so I can have both sides of the sound into my headphones (couldn`t get it working with an Audigy SE; giant waste of $30).
I use Vista and I really regret it, but anyone who can tell me if any cards will work with all three of these things, please do. Im dying here.

Thanks David for the reply, When I look at the Info on the Log & Transfer window it gives a number.mpg,
when I transfer it, I see it as Apple ProRes 422. I shot it in PAL & as far as I can remember,
PAL is progressive.
Also I shot it it in Std. mode as the other Clips I need to use were filmed IN DV CAM std.
again thanks
Brendan

Sdhc cards stopped working with 10.9.1 update

sdhc cards stopped working with 10.9.1 update. I've tried multiple readers with no affect. Any ideas?

Have you checked for an update and/or asked the developer for help?

HELP....need a good sound card that works with Windows 7 64 bit

I've searched the internet and I'm seeing that folks are struggling with getting sound cards to work with Windows 7 (particularly the 64 bit systems). I know there are stability issues with the 64 bit system but I'm looking to install a decent sound card to improve stereo sound from my HP Pavilion (h8-1260t). The onboard sound is OK, but I'm looking for higher fidelity and the shortcomings of the stock sound chip is noticeable when played through my hi fi system. Don't really need 'surround sound' (I'm not a gamer) but I'm assuming any card that comes with this feature will also produce a quality stereo signal. I also like to archive music from steaming sources and have found a significant loss of sound quality once the track is saved. I'm assuming a good sound card will help with this. Any advice would be greatly appreciated.

Spauld, welcome to the forum.
I suggest finding a sound card that you like and contacting the manufacturer's Customer Service to assure its compatibility with Win7 64-bit. They are the experts on their products. While I am not a fan of dedicated sound cards because their drivers are conflict prone, I would buy a Creative Soundblaster. They have been proven over time.
Please click "Accept as Solution" if your problem is solved.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee.

Is Neteller virtual credit card is working with App store

Hello,
Im from india and
I wanna buy some apps from Apple App-store. I don't have any credit card so I registered fro entropay and Neteller virtual credit card
So, my questioon is Neteller virtual credit card is working with iTunes store or not?

If you are an old timer, sometimes the App store gets confused about your account.
You might be "oldtimer"
Or you might be "[email protected]"
This is the situation for me (Yes, I am old and long suffering).
This situation means sometimes you have to log in as the other user to get things to work, or to see things you have already purchased. I assume this is due to the fact that I was an iwork/iweb/.mac/whateveapplecallsitthisweek/icloud user.
Other then that, you might login in to the web interface from your mac and try to update your crdit card info from there. If it's all correct and the card is good it SHOULD go.
Best of luck,
Marty

HT4990 is there a version of cards that works with ios5.1.1

is there a version of cards that works with ios 5.1.1

http://www.stuffit.com/mac/expander/
I'm pretty certain that I got my version of stuffit, which has worked excellently on my Intel MBP, from that site. I downloaded it around the time when I first got the laptop, so I'm pretty sure that's the site.
If it's not let me know and I can give you links to a different site, or I can just e-mail you the installer file directly.
If it doesn't work for any other reason, or does the encrypted thing that you stated, let me know I'll look into it.
Peace
Bweb

Mb sound not working. Can i add a sound card to work with PP cs6?

I have a sabertooth x58, pc, win 7. I lost the audio monitoring all of a sudden. Also tryed windows media player & all windows sounds are not being played as well. Tryed absolutely everything. Need to go to plan B.
Can i add a sound card to work with PP cs6?
http://www.newegg.com/Product/Product.aspx?Item=N82E16829132052

>Tryed absolutely everything
What does that mean?
Have you removed the sound card driver via control panel and let Win7 reinstall?

[p7-1240] How can I tell which graphics cards will work with my motherboard?

I recently went through the nightmare of trying to install a Gigabyte GTX 650 in my PC. After a few days of struggling and scouring the internet for answers, I discovered that it is incompatible with the BIOS on my motherboard, and HP does not offer BIOS updates. I returned the card and am now looking for a new one, but I am unsure of which cards will work now, since my computer met all of the system requirements for the graphics card, and It stil ldid not work. Since GPU manufacturers do not list BIOS specs under system requirements, how can I tell if a graphics card will work with my sytem?
My computer is a p7-1240 with an upgraded 520W PSU and approximeately 11" of room to install the card.
This question was solved.
View Solution.

Thexn, welcome to the forum.
The problem is, many of the newer video cards require the computer to have a full UEFI BIOS. HP began using one in mid-October, 2012. Before this date the BIOS is Legacy. This is why the video card didn't work with your computer.
I don't know what you want to spend for a card, but MSI makes a GTX 750ti that has a hybrid VBIOS. It has a switch to change to Legacy or UEFI. There is a video link directly below the picture of a card. Paul from Newegg gives a full description of the card.
I like EVGA cards the best. Their Tech Support has given me a lot of information about their cards. However, you have to go back to a GT 640 card to find one of their cards that doesn't require the UEFI BIOS. They do have some updates for their BIOS'es that solve the problem, but you have to call them for the exact cards.
Please click the "Thumbs up + button" if I have helped you and click "Accept as Solution" if your problem is solved.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee.

Does lightning SD card reader work with iPad Mini and iOS7?

I order new iPad Mini Retina and wan to know;
does the lightning SD card read works with iOS7?

Yes.

How can i set up my iPod touch to work with a wireless keyboard?

How can I set up my iPod touch to work with my wireless Apple keyboard?

What Apple keyboard?The original Apple white keyboard with four batteries tonot work with any iPods
What model iPod? Only the 3G and later support BT keyboards
iOS: Third-party Bluetooth headsets, headphones, and keyboards
Wireless input devices: Bluetooth frequently asked questions

Setting up PCI-DNET card to work with Eurotherm 2404 Controller w/Device Net

Similar Messages

Maybe you are looking for