Settings allied data Copperjet 1616-2p and AEBS

I am trying to install the Apple Airport Extreme BS in combination with an Allied data Copperjet 1616-2p modem/router. My internet connection should in optimal conditions be able to get to speeds of 2Mb/sec. In my settings, everything works, as long as I put the AEBS in bridge mode. Only problem is that the speed of the internet connection and the network speed is not optimal. Network speed is limited to 500kb/sec. and internet speed is 500kb/sec or slower. Sometimes dropping to 10kb/sec.
Does anyone know the optimal settings fot this combination? Is it possible to forward the modem (Bridge?) to the AEBS, and use the AEBS as a modem? Is it possible to use portforwarding?

Does anyone know the optimal settings fot this combination? Is it possible to forward the modem (Bridge?) to the AEBS, and use the AEBS as a modem? Is it possible to use portforwarding?
It may be possible to reconfigure this Gateway as a bridge. The issue you may come up with is if you are using ADSL Internet service and your ISP requires PPPoA to authenticate you before gaining access to their service, the AEBS does not support this protocol ... only PPPoE.
Also, the AEBSn is not a Gateway or a combination modem & router type of device ... only the router part. You would still need a modem for Internet access.
Depending on which device, the Gateway or AEBS has NAT enabled, it should be possible to configure them for port forwarding/mapping.

Similar Messages

  • Is there a way from where I can restore my profile from a back-up that I took from a folder (e.g \Local Settings\Application Data\Mozilla\Firefox\Profiles\)

    Before re-installing Firefox 19, I mistakenly took backup of my profile from a folder - C:\Documents and Settings\garan14\Local Settings\Application Data\Mozilla\Firefox\Profiles and not from C:\Documents and Settings\garan14\Application Data\Mozilla\Firefox\Profiles.
    While installing, I selected "Delete the old profiles" option and I don't see any old profile folder under C:\Documents and Settings\garan14\Application Data\Mozilla\Firefox\Profiles.
    However, I have a lot of important data saved under that profile which now has got deleted.
    Is there any way I can still restore the data from old profile? (P.S.: As mentioned above, I have a back-up of profile folder which resides under Local Settings folder)
    I am in a desperate need for the help. Pls reply as soon as possible.

    i have some problem. i delete firefox profile and i cannot use mozilla right now. can you help me ? thank you

  • I performed a time machine backup without plugging my labtop into a power source. My computer died and all the settings were changed, ie the clock and date were changed back to 2001. So I tried to restore my computer using a previous time machine backup.

    I performed a time machine backup without plugging my labtop into a power source. My computer died and all the settings were changed, ie the clock and date were changed back to 2001. So I tried to restore my computer using a previous time machine backup. (which I now know was wrong). However, when time machine tried to restore it said there was not enough room to do a backup. It seems that it did a half backup because some essential  files such as system profiler are now missing. Can I undo this restore...? What can I do to fix this

    You need to do a full system restore, per Time Machine - Frequently Asked Question #14.
    If that sends a message, please note the exact wording.

  • HT4157 I just got an iPad 16GB+3G. When I try to set up a cellular data account (settings cellular data view account) it wants the login info and password,which I don't have because I have yet to set up the account. How do I get to a "set up account" scre

    I have a new iPad2 16GB+3G. ( Only got this yesterday.)  I have set up a wireless router so am able to use WiFi at home. When I attempt to set up a cellular data connection (ATT) I get to the "view account" which asks for my login ID and password, which of course I do not have yet because I haven't set up an account yet. How do I get to a "set up account" screen?

    I'm taking that this is a used iPad. Have you removed the microSIM and got one of your own?
    Also, have you cleared it out with Settings > General > Reset > Erase All Content and Settings?
    And if that does not work you may need to contact the cell provider.

  • Firefox is creating endless copies of C:\Documents and Settings\Catain Kirk\Local Settings\Application Data\Mozilla\Firefox\Profiles\afbrfhnj.default\Cache ... how do I stop it

    I just installed 9.0.1 and it continually creates copies of C:\Documents and Settings\Catain Kirk\Local Settings\Application Data\Mozilla\Firefox\Profiles\afbrfhnj.default\Cache ... how do I stop it !!!
    I'm running Windows XP Version 5.1 SP3.

    Hi,
    That is the disk cache of Firefox, where contents of loaded pages are kept for faster retrieval and it also helps to conserve bandwidth. To disable this: '''Tools''' ('''Alt''' + '''T''') > '''Options''' > '''Advanced''' > '''Network''', check (tick) '''Override automatic cache management ''' and put the value at zero.
    [https://support.mozilla.org/en-US/kb/Options%20window%20-%20Advanced%20panel?as=u#advanced_network Cache]
    Useful links:
    [https://support.mozilla.com/en-US/kb/Options%20window All about Tools > Options]
    [http://kb.mozillazine.org/About:config Going beyond Tools > Options - about:config]
    [http://kb.mozillazine.org/About:config_entries about:config Entries]
    [https://support.mozilla.com/en-US/kb/Page%20Info%20window Page Info] Tools (Alt + T) > Page Info, Right-click > View Page Info
    [https://support.mozilla.com/en-US/kb/Keyboard%20shortcuts Keyboard Shortcuts]
    [https://support.mozilla.com/en-US/kb/Viewing%20video%20in%20Firefox%20without%20a%20plugin Viewing Video without Plugins]
    [http://kb.mozillazine.org/Profile_folder_-_Firefox Firefox Profile Folder & Files]
    [https://developer.mozilla.org/en/Command_Line_Options#Browser Firefox Commands]
    [https://support.mozilla.com/en-US/kb/Basic%20Troubleshooting Basic Troubleshooting]
    [https://support.mozilla.com/en-US/kb/common-questions-after-upgrading-firefox-36 After Upgrading]
    [https://support.mozilla.com/en-US/kb/Safe%20Mode Safe Mode]
    [http://kb.mozillazine.org/Problematic_extensions Problematic Extensions]
    [https://support.mozilla.com/en-US/kb/Troubleshooting%20extensions%20and%20themes Troubleshooting Extensions and Themes]
    [https://support.mozilla.com/en-US/kb/Troubleshooting%20plugins Troubleshooting Plugins]
    [http://kb.mozillazine.org/Testing_plugins Testing Plugins]

  • I cannot uninstall itunes from my computer PC. I cannot update itunes on my computer. I get this message." C:\Documents and Settings\Sally-Anne\Local Settings\Application Data\Apple\Apple Software Update\'iTunes.msi' is not a valid installation package

    I cannot uninstall itunes from my computer PC. I cannot update itunes on my computer. I get this message." C:\Documents and Settings\Sally-Anne\Local Settings\Application Data\Apple\Apple Software Update\'iTunes.msi' is not a valid installation package Try to find the installation package itunes.msi in a folder from which you installiTunes."
    I have tried a serach for the file itunes.msi and nothing comes up.
    Help anyone/
    thanks

    I get this message." C:\Documents and Settings\Sally-Anne\Local Settings\Application Data\Apple\Apple Software Update\'iTunes.msi' is not a valid installation package Try to find the installation package itunes.msi in a folder from which you installiTunes."
    (1) Download the Windows Installer CleanUp utility installer file (msicuu2.exe) from the following Major Geeks page (use one of the links under the "DOWNLOAD LOCATIONS" thingy on the Major Geeks page):
    http://majorgeeks.com/download.php?det=4459
    (2) Doubleclick the msicuu2.exe file and follow the prompts to install the Windows Installer CleanUp utility. (If you're on a Windows Vista or Windows 7 system and you get a Code 800A0046 error message when doubleclicking the msicuu2.exe file, try instead right-clicking on the msicuu2.exe file and selecting "Run as administrator".)
    (3) In your Start menu click All Programs and then click Windows Install Clean Up. The Windows Installer CleanUp utility window appears, listing software that is currently installed on your computer.
    (4) In the list of programs that appears in CleanUp, select any iTunes entries and click "Remove", as per the following screenshot:
    (5) Quit out of CleanUp, restart the PC and try another iTunes install. Does it go through properly this time?

  • I am really angry that I get this message every time I try to update Itunes.  "The File 'C:/documents and settings\DEAN\Local Settings\Application Data\Apple\Apple Software Update\itunes.msi' is not a valid installation package for the product itunes.  Tr

    I am really angry that I get this message every time I try to update Itunes.
    “The File ‘C:/documents and settings\DEAN\Local Settings\Application Data\Apple\Apple Software Update\itunes.msi’ is not a valid installation package for the product itunes.  Try to find the installation package ‘itunes.msi’ in a folder from which you can install itunes.
    What kind of gobbledegook is that?  Are you or Microsoft crazy.  Us computer users need simpler instructions.  Or you need to write your programs so that they work.
    Signed,
    Frustrated Apple User
    Dean Weaver

    “The File ‘C:/documents and settings\DEAN\Local Settings\Application Data\Apple\Apple Software Update\itunes.msi’ is not a valid installation package for the product itunes.  Try to find the installation package ‘itunes.msi’ in a folder from which you can install itunes.
    (1) Download the Windows Installer CleanUp utility installer file (msicuu2.exe) from the following Major Geeks page (use one of the links under the "DOWNLOAD LOCATIONS" thingy on the Major Geeks page):
    http://majorgeeks.com/download.php?det=4459
    (2) Doubleclick the msicuu2.exe file and follow the prompts to install the Windows Installer CleanUp utility. (If you're on a Windows Vista or Windows 7 system and you get a Code 800A0046 error message when doubleclicking the msicuu2.exe file, try instead right-clicking on the msicuu2.exe file and selecting "Run as administrator".)
    (3) In your Start menu click All Programs and then click Windows Install Clean Up. The Windows Installer CleanUp utility window appears, listing software that is currently installed on your computer.
    (4) In the list of programs that appears in CleanUp, select any iTunes entries and click "Remove", as per the following screenshot:
    (5) Quit out of CleanUp, restart the PC and try another iTunes install. Does it go through properly this time?

  • I did a clean install and lost all of my iweb data and settings. My site is up and published through yahoo's server. Is there a way to retrieve/import so I can make changes?? HELP!

    I did a clean install and lost all of my iweb data and settings.
    My site is up and published through yahoo's server.
    Is there a way to retrieve/import so I can make changes?? HELP!
    Can I do this through wordpress or using html code?
    Thanks!

    Is there a way to retrieve/import so I can make changes?? HELP!
    It's often asked and answered.
    Search this forum for similar disasters : lost iweb file
    The answer usually is No. You'll have to start from scratch. Unless you have a backup.
    Can I do this through wordpress or using html code
    No.

  • I ran a settings up date on an iPad 2 and now it won't start back up.  Just a black screen and an apple.  Any ideas what to do?

    I ran a settings up date on an iPad 2 and now it won't open back up.  Just a black screen with an apple.  Any ideas?

    Have you tried a soft-reset to see if that gets it to boot up properly ? Press and hold both the sleep and home buttons for about 10 to 15 seconds, after which the Apple logo should reappear and it will hopefully boot up fully - you won't lose any content, it's the iPad equivalent of a reboot.

  • Buongiorno, ho questo problema, quando cerco di aggiornare alcuni programmi, nella fase di disinstallazione  mi esce il messaggio "errore durante la lettura del dati di protezione del file c/documents and settings/lorenzo/dati applicazioni/microsoft/inter

    Buongiorno, ho questo problema, quando cerco di aggiornare alcuni programmi, nella fase di disinstallazione  mi esce il messaggio "errore durante la lettura del dati di protezione del file c/documents and settings/lorenzo/dati applicazioni/microsoft/internet explorer/quick launch/getlasterror 87" la disintallazione si interrompe e non permette l'aggiornamento. Qualcuno può aiutarmi? Grazie

  • I have had my IPAD2 for quite a while but haven't activated my cellular data for about a year.  I am now trying to activate and when I go to cellular data, turn it on and try to tap view account i just get a message that says "connection to server lost".

    I have had my IPAD2 for quite a while but haven't activated my cellular data for about a year.  I am now trying to activate and when I go to cellular data, turn it on and try to tap view account i just get a message that says "connection to server lost".  I could swear the last time I used cellular data you would see the signal in the upper left corner and I only see "no service" there, I am in a location where I know I should have service.  Is there something I should do to my IPAD?  I tried resetting, I tried clearing cookies and history in Safari (after reading a post n these discussions).  I don't know what to do next. My IOS version is 6.1.3.  I did go into Network from the general tab and I see it says "SIM not provisioned".    HELP and Thank you in advance.

    Hello Theresa818,
    Thank you for using Apple Support Communities!
    It sounds like the cellular data will not activate for some reason on the iPad.
    I found this article that will help you resolve this issue here, named iPad (Wi-Fi + Cellular Models): Troubleshooting a cellular data connection, found here http://support.apple.com/kb/TS4249
    Check for a carrier settings update.
    Update your iPad.
    Toggle the Cellular Data setting off and on under Settings > Cellular Data.
    Restart your iPad.
    Tap Settings > General > About. Locate the Carrier entry and make sure that your carrier is correct.
    If your SIM card has SIM PIN enabled, try turning it off: Tap Settings > Cellular Data > SIM PIN.
    Make sure you're in an area of good coverage. If the cellular data connection works in another area, contact your carrier to report the original affected area.
    Reset network settings: Tap Settings > General > Reset > Reset Network Settings.
    Restore the iPad as new.
    If none of the above steps resolves the issue, make an appointment at an Apple Retail Store, contact your carrier, or contact AppleCare to troubleshoot further.
    I know you may have done one or two of the steps here, so you can skip those.
    Take care,
    Sterling

  • Passing data b/w applet and apache server

    Hi all,
    I have an application that runs in the JApplet.I have to pass data b/w server and applet.The
    datas are brought from the server using php to the browser and passed to applet using param
    tags.
    1.Is it possible to set value for the param tag from applet?
    2.How to retrieve data from the param tag to the applet in the form of an array.
    In the getParameter it is required to specify the param name.
    Is it possible to retrieve data from param tag similar to that of getting data from command
    line arguments array.

    Hi all,
    I have an application that runs in the JApplet.I have
    to pass data b/w server and applet.The
    datas are brought from the server using php to the
    browser and passed to applet using param
    tags.
    1.Is it possible to set value for the param tag from
    applet?Why do you ever want to do it? It sounds like setting arguments passed to a program's main method from command line after the main method has been invoked. It is possible though to dynamically set any values for any applet params using php before the applet gets loaded to the browser window as you generate an html file on the server side.
    2.How to retrieve data from the param tag to the
    applet in the form of an array.
    In the getParameter it is required to specify the
    param name.
    Is it possible to retrieve data from param tag similar
    to that of getting data from command
    line arguments array.You can use some naming/numbering convention for your params. For example settings1, settings2 ... Then you can loop in your code retrieving the values like getParameter("settings" + i) checking to see that it is not null or empty.
    However, if you don't want to reload the applet (together with the page) just to get some new data from the server, you can establish a tcp/ip connection as elchaschab recommended.
    Cheers!

  • How is it possible to accrue data charges on wifi and asleep?

    I'm not very happy with what's going on right now.  My family of 3 shares a data plan of 8GB.  I use under 1G, my husband <1G-1.5G and my son uses a ton so I decided to start looking into when/how much data is being used.  In the previous billing cycle we went over by .009 on the final day of the billing cycle so what's the point to pay $10 for 2G and then not be able to change it back, therefore I took the stupid $15 overage charge for literally nothing.  Anyway, I began to look through the time stamps and data usage per phone and it's pretty fishy. I'm being charged data at 4:06am, 10:06am, 4:06pm and so on.  I have an iphone5, my husband has an iphone6 and my son an iphone 6+.  Spoke with a rep tonight who claimed it may be due to my wifi losing connectivity and auto updating while connected to the LTE.  That's a load.  My whole family switched to Verizon because we couldn't ever get a good signal where we live with AT&T.  My husband finally was forced to try a different company due to work and having to have a reliable network where we live. Not one dropped call, not one issue with wifi-Verizon was actually the miracle mobile provider I never knew existed.  I waited a few months to make sure that it wasn't too good to be true and at once dropped AT&T totally and switched my son and my phone to Verizon as well.  Having a teenager I knew we needed to probably have more data to be on the safe side but they can't seem to tell me how his data is being used and from 4/2 to today (4/14) he has used over 4G of data according to them.  I pull up the dates and times and know for a fact that he was connected to home wifi for 1.6G+ and at his school wifi for another 1.6G+ and only 1.2G+ could have possibly been used off wifi.  And I also see that there are massive amounts of complaints regarding this same type of sham.  Not to mention I had added Family Base to be able to set limits on the data my son uses. But apparently since he's able to access the MyVerizon account from his phone (albeit he isn't an authorized user on the Family Base plan) he is able to go in and change any parameters I had set up.  So tonight I go in and remove this feature from our account and now 30 minutes later I get a "Welcome to Verizon Family Base" text.  WTH is going on??? I want real answers now or I will be looking into what others have done regarding this type of abuse.  I had high hopes that this was going to be an honest, reliable network I could trust but this data business is insanely bogus.  I'd like to hear back from someone regarding getting this researched and resolved.  I don't want to feel discontent about something that has been going good so far.  But I don't really feel like I should have to turn off all cellular data and close all open apps when I'm on wifi in order to keep from having data charged inappropriately.  Thanks for your help and prompt resolution to my concern.

    We are suffering from the same nightmare. It has been 8 solid weeks of phone calls to Verizon, then Apple, then to our cable service provider; daily data checks; overage charges; fights with the teen; HOURS of time invested in trying to get to the bottom of sudden and exponential jump in data usage. It started about a month after we upgraded my daughter's phone to a 5s. She is even more conscientious than me about not using it unless we are connected to wifi. For the first month, all was fine and we were going through the normal 2G. Then, with absolutely NO habit or usage change on our end, we were blasting through that like lightening. She was disciplined for the overuse. We added another 1G just to be safe. That went even faster than the 2G!!! We are now at 6GB at almost double the rate we went through 2!!!
    I have kept a log of the time spent trying to solve this issue -- almost 5 hours of phone time alone. I literally have an AppleCare supervisor in my phone contact list because he is so perplexed!!!! After several Verizon technical support calls, we finally an agent who really wanted to help. She was convinced my daughter's phone had a rogue (malware) virus. Apple said it had to be the hardware. But when we really looked at the metrics -- both of our iPhones AND the iPad all all using data when on wifi, supposedly. We had one month of overage charges refunded, but with the problem not solved (reset both phones to factory settings; exchanged our modem for a new one !!!) I added -- you guessed it -- MORE DATA!!!
    I didn't see how Verizon could be guilty of fraud -- after all, something of this magnitude would put the entire company out of business ultimately and it just doesn't make sense. But this is WAY OFF. Further, mid-way through our issue, the data category that was using the most data on my daughter's phone -- "Business Services" -- suddenly disappeared and now the main usage category is "Web Apps". Verizon. Really? It's a poor show.
    I'm considering eating the contract termination fee and returning to AT&T. I'm not quick to assume, which is why I've spent months assuming some responsibility for the data, but it's very clear to us now that there is something very illegal happening here.

  • How can I change the date format in Reminders and in Notes?

    How can I change the date format in both Notes and Reminders? Preference on Imac and Settings in IOS do not allow me to change the format in those 2 apps.
    I Like to see 10oct rather than 10/10, as an example.

    pierre
    I do not have Mavericks or iOS - but the first thing I would do is reset the defaults - I'll use Mavericks as an example
    From If the wrong date or time is displayed in some apps on your Mac - Apple Support
    OS X Yosemite and Mavericks
        Open System Preferences.
        From the View menu, choose Language & Region.
        Click the Advanced button.
        Click the Dates tab.
        Click the Restore Defaults button.
        Click the Times tab.
        Click the Restore Defaults button.
        Click OK.
        Quit the app where you were seeing incorrect dates or times displayed.
        Open the app again, and verify that the dates and times are now displayed correctly.
    Then customize to taste - OS X Mavericks: Customize formats to display dates, times, and more
    OS X Mavericks: Customize formats to display dates, times, and more
    Change the language and formats used to display dates, times, numbers, and currencies in Finder windows, Mail, and other apps. For example, if the region for your Mac is set to United States, but the format language is set to French, then dates in Finder windows and email messages appear in French.
        Choose Apple menu > System Preferences, then click Language & Region.
        Choose a geographic region from the Region pop-up menu, to use the region’s date, time, number, and currency formats.
        To customize the formats or change the language used to display them, click Advanced, then set options.
        In the General pane, you can choose the language to use for showing dates, times, and numbers, and set formats for numbers, currency, and measurements.
        In the Dates and Times panes, you can type in the Short, Medium, Long, and Full fields, and rearrange or delete elements. You can also drag new elements, such as Quarter or Milliseconds, into the fields.
        When you’re done customizing formats, click OK.
        The region name in Language & Region preferences now includes “Custom” to indicate you customized formats.
    To undo all of your changes for a region, choose the region again from the Region pop-up menu. To undo your changes only to advanced options, click Advanced, click the pane where you want to undo your changes, then click Restore Defaults.
    To change how time is shown in the menu bar, select the “Time format” checkbox in Language & Region preferences, or select the option in Date & Time preferences.
    Here's the result AppleScript i use to grab the " 'Short Date' ' + ' 'Short Time' "  to paste into download filenames - works good until I try to post it here - the colon " : " is a no-no but is fine in the Finder
    Looks like iOS Settings are a bit less robust
    - Date/Time formats are displayed according to 'tradition' of your region > http://help.apple.com/ipad/8/#/iPad245ed123
    buenos tardes
    ÇÇÇ

  • Calendar Tile on Windows 8.1 displaying incorrect date for icloud calendar but date icon displays correct date on iPhone 5 and iPad Air

    Calendar Tile on Windows 8.1 displaying incorrect date for icloud calendar but date icon displays correct date on iPhone 5 and iPad Air.  Date on Windows 8.1 is correct.  Thank you.

    Try doing  a reset on your phone. Sounds like your carrier's time set is not getting through to your device. If the reset doesn't do it, then go to Settings>General>Reset>Reset Network Settings. That should do it.

Maybe you are looking for