Settings for 50% claimable is maintained for Basic, Cess, Edu Cess and Add

Hi,
Can you tell me where the settings for captial goode 50% claimable is maintained for Basic, Cess, Edu Cess and Additional duty.
Regards
VR

Hi Manish
for Capital Goods Procurement,
first the material and chapter id has to be maintain and with that material code it should be decalred for Assets.
Customization in SPRO for maintaine specify Excise accounts per Excise TT as.........
when ever you capture the excise for capital goods the RG23C Register type is updated for Capital Goods showing the 50 % excise can be avail for present financial year and 50 % next financial.
The Excise Posting Entries must be like
                                    Cenvat Account           Dr.       (50%)
                                    Cenvat On-hold           Dr.       (50%)
                                    Cenvat Clearing                      Cr.
You can check the balance avail in T Code J2I8
Pls refer the below link also it may help you much better...........
http://help.sap.com/bp_bblibrary/500/Documentation/J84_BB_ConfigGuide_EN_IN.doc
Regards,
patil

Similar Messages

Upgrade 2 basic lines to smartphones and add a smartphone line

I have 3 lines we are on a family share plan and line 1 is the only smartphone.
Line 1 unlimted data smartphone
line 2 and 3 are due for upgrades just basic phones but want to switch to smartphones plus add a 4th line. do I have to give up my unlimted data to get them on a data plan?
Thanks for any feed back.

Each line has its own contract, so making changes to one line shouldn't affect the other lines. You should be able to upgrade the two basic phones to smartphones and add a 2GB ($30) data plan to each and add the fourth line without affecting the unlimited data line. You may want to check the math to ensure that it isn't cheaper to switch to the More Everything plan, though (depending on data usage) ... and be aware that unless you make the changes on-line, VzW reps will probably try to steer you toward changing to the More Everything plan, but that's not required.

Table for seeing the Views maintained for a material in material master

i have maintained CLASSIFICATION view for certain materials, but when i go to table MARC and check the maintenance status, i cannot see the letter "C" which stands for classification.
I need to sort out the materials for which classifiction view has been maintained.
Is there any other way to do it?
Pls help
Thanks
Neeraj

Hi
U Can check the status of Veiws maintained in MSTA
The views are
A Work scheduling
B Accounting
C Classification
D MRP
E Purchasing
F Production resources/tools
G Costing
K Basic data
L Storage
P Forecasting
Q Quality management
S Warehouse management
V Sales
X Plant stocks
Z Storage location stocks
thanks

I want to delete my gmail on my iPad, yet my iPad won't allow me to access the option. I went on my iPad settings Mail, Contacts, Calendars, although i cannot tap on iCloud, Gmail, or Add Account... How do i fix this?

I want to delete/sign out my gmail on my Ipad, but my ipad won't allow me to delete it.
Example:
I tapped on Settings>Mail, Contacts, Calendars, although I cannot tap on iCloud, Gmail, and Add Account...
how do I fix this?

Sorry, you said Gmail. If that's the case, you can try resetting your iPad by simultaneously pressing and holding the Home and Sleep/Wake buttons until you see the Apple Logo. This can take up to 15 seconds so be patient and don't release the buttons until the logo appears.
Try again to see if the problem persists.

WHT - Number Group not maintained for co code 1000 S.code IEQ 5400

WHT experts
I got the error when I create Remittance challan (J1INCHLN) that
Number group not maintained for co code 1000 section code IEQ 5400 and Business place 194H
I have defined Number group for Challan though I got above error
This is in Prdn system. So pl give me solution asap.

Hi,
Assign number number ranges to section code and business place wise and attach business place and section code. go to sm30 and specify manually
J_1IEWTNUMGR_1     Number Groups For Internal Challan Numbers-EWT India:SECCO
J_1IEWTNUMGR_N     Number Groups For Internal Challan Numbers-EWT India:SECCO
J_1IEWT_CERTNO     Number Ranges for Withholding Tax Certificates
go ahead with this path Spro-sap img-financial accounting-fa global settings-withholding tax-extended withholding tax-basic settings-south korea-define section codes.
hope this is clear, if yes assign points any problem revert me back
Regards,
Sankar

Fiscal year variant is not maintained for calendar year 2009

Hi,
After upgrade to BI 7.0 we are getting error: "Fiscal year variant & is not maintained for calendar year 2009" while opening a query through Bex Analyzer.
Basically it is happening like when we open a particular query, the Variable selection screen comes up, then on clicking the exection button (after selection) it shows SYSTEM_FAILURE exception & clicking the details button, shows the message ""Fiscal year variant is not maintained for calendar year 2009"
Please provide some information/resolution to this.
Thanks,
Shantanu.

HI,
Please ensure that you have defined your fiscal year variant in OB29
correctly. It is necessary that:
1. the previous year has been maintained,
2. an entry for Dec 31 exists in each fiscal year,
3. the following fiscal year has been maintained.
Hope this helps.
Regards,
Nitin

Fiscal year variant Z1 is not maintained for calendar year 2012 when loadin

Dear Experts,
We are working on BI7.0 extracting data from ECC 6.0.
I am trying to load data from 0HR_PY_PP_1 which is a Self DataSource in our BW System (extracts data from 0EMPLOYEE and 0PERSON) to load into ZPA_C50 which is a copy of BCT InfoCube 0PAPA_C02 (Headcount).
The data has come through into the PSA very well.
However, DTP is throwing an error while loading 32242 records of data from PSA into ZPA_C50 InfoCube. The error details as below:
Error while updating to target ZPA_C50 (type INFOCUBE)
Fiscal year variant Z1 is not maintained for calendar year 2012 FGV 2
Messages for 1 data records saved; request is red acc. to configuration
Processing Terminated
We are actually doing a Re-implementation of BW 3.0b in BI 7.0 Ehp1. We have imported Maintenance of Fiscal Year Variant from the BW 3.0b Production System. So this shouldn't be a problem I guess since I have also checked the setting in SPRO in BI 7.0 Development (New) System and they are looking good.
Also, when I do a Filter on 0CALDAY in DTP from 01.01.1900 to 31.12.2010, the loads are working fine. I want the load to run without any Filters on 0CALDAY.
Has anyone been in similar situation. How did you resolve this issue? Your time is very much appreciated.
Thanks in advance.
Chandu

Dear Experts
Thanks for your time.
We have resolved this issue ourselves. We have maintained 'Shortened Fiscal Years' for 'Z1' and it is working fine now. Steps are as below:
In BI Dev System -> SPRO -> SAP Reference IMG -> SAP Customizing Implementation Guide -> SAP NetWeaver -> Business Intelligence -> General BI Settings -> Maintain fiscal year variant -> Select 'Z1' Fiscal Year Variant and then DoubleClick on 'Shortened Fiscal Years' to set the Fisc Year Variant -> Save.
The dataload should work fine now.
Cheers,
Chandu

Storage rules for an editing rig. Some basics.

How do you set up your editing machine in terms of disks for maximum performance and reliability? (SSD's are left out here.)
This is a question that often arises and all too often one sees that initial settings are really suboptimal. These rules are intended to help you decide how to setup your disks to get the best response times. Of course the only disks in an editing machine must be 7200 RPM types or faster. No GREEN disks at all.
Rule 1: NEVER partition a disk. You may ask why? First of all, it does not increase disk space, it just allocates the space differently. However, the major drawback is that for a partitioned disk the OS must first access a partition table at the beginning of the disk for all accesses to the disk, thus requiring the heads to move to the beginning of the disk, then when it has gotten the partition info move to the designated area on the disk and perform the requested action. This means much more wear-and-tear on the mechanics of the disk, slower speeds and more overhead for the OS, all reducing efficiency.
Rule 2: Avoid using USB drives, since they are the slowest on the market. Do not be tricked by the alleged bandwidth of USB 2.0 advertisements, because is just is not true and remember that the alleged bandwidth is shared by all USB devices, so if you have a USB mouse, keyboard, printer, card reader or whatever, they all share the bandwidth. Stick to SCSI or SATA disks or e-SATA. If needed, you can use Firewire-800 or even Firewire-400 disks, but they are really more suited for backups than for editing.
Rule 3: Use at least 3 different physical disks on an editing machine, one for OS/programs, one for media and one for pagefile/scratch/renders. Even on a notebook with one internal drive it is easy to accomplish this by using a dual e-SATA to Express card connector. That gives you an additional two e-SATA connections for external disks.
Rule 4: Spread disk access across as many disks as you have. If you have OS & programs on disk C:, set your pagefile on another disk. Also set your pagefile to a fixed size, preferably somewhere around 1.5 times your physical memory.
Rule 5: Turn off index search and compression. Both will cause severe performance hits if you leave them on.
Rule 6: If the fill rate on any of your SATA disks goes over 60-70% it is time to get a larger or an additional disk.
Rule 7: Perform regular defrags on all of your disks. For instance, you can schedule this daily during your lunch break.
Rule 8: Keep your disks cool by using adequate airflow by means of additional fans if needed. You can use SMART to monitor disk temperatures, which should be under 35 degrees C at all times and normally hover around 20-24 C, at least in a properly cooled system.
Rule 9: If people want raid, the cheapest way is to use the on-board IHCR or Marvell chip, but it places a relatively high burden on the CPU. The best way is a hardware controller card, preferably based on the IOP348 chip. Areca ARC and ADAPTEC come to mind. 3Ware uses it's own chipset and though not bad, they are not in the same league as the other two. Promise and the like in the budget range are no good and a complete waste of money. Expect to spend around $ 800 plus for a good controller with 12 connectors internally and 4 e-SATA connectors. Important to consider in a purchasing decision is whether the on-board cache memory can be expanded from the regular 256/512 MB to 2 or even 4 GB. Be aware that 2 GB cache can be relatively cheap, but the 4 GB version extremely costly ($ 30 versus $ 300). For safety reasons it is advisable to include a battery backup module (BBM).
Rule 10: If you can easily replace the data in case of disk failure (like rendered files), go ahead and use raid0, but if you want any protection against data loss, use raid 3/5/6/10/30/50. For further protection you can use hot spares, diminishing downtime and performance degradation.
In general when you get a new disk, pay close attention to any rattling noise, do perform regular disk checks, and in case of doubt about reliability, exchange the disk under guarantee. Often a new disk will fail in the first three months. If they survive that period, most of the disks will survive for the next couple of years. If you use a lot of internal disks like I do (17), set staggered spin-up to around 1 second to lessen the burden on the PSU and improve stability.
Hope this helps to answer some basic questions. If not, let me know. Further enhancements and suggestions are welcome.

...well, it is a northern D - they call us often "Fischköpfe" because we love to eat fish here in Hamburg!
I just have summarized a bit the storage configuration I am thinking of
RAID Type
Objective
System requirements
RAID level
Offline Storage
store a whole video project (1h of 4k material requires about 128 GB)
needs to be highly reliable (redundancy is a must);
doesn't need to be extremely fast;
discs can be cheap because they don't have a high burden (just upload & download) to the video RAID.
10
Video RAID
store material for a day work
fast and reliable
10
Installation RAID
just to install Windows XP with CS4 Master Collection
redundant but speed isn't critical here
1
Working RAID
for page-file/scratch/renders
as fast as possible
disc failure isn't a big problem
0
In order to realize this, I am thinking of the following configuration
RAID Type
number of discs
Type
GB/disc
tot. storage [GB]
usable storage [GB]
cost [€]
Offline Storage
8
SATA
1500
6000
4800
900
Video RAID
6
SCSI/SAS
300
900
720
2100
Installation RAID
2
SCSI/SAS
36
36
30
200
Working RAID
4
SCSI/SAS
147
580
470
1000
Here are my assumptions and constraints:
I only have 6 bays for the Installation - and working RAID;
For the video RAID I also would like to reuse an enclosure, which just has 6 bays;
I would need to buy a NAS enclosure - so here I am open minded and just assumed 8 bays;
the usable storrage I estimated as 80% of the total storage;
discs, which are used heavily should be SCSI or SAS - I am thinking of the Cheetah 15K
Looking into the cost associated, I hit 4000€ easily just for discs. Ok, I can reuse some discs and enclosures, which I have here - but since I need to purchase the NAS enclosure (with 8 bays), which will also cost 1000€ additional, I will use 25% of my foreseen budget for storage.

Fiscal year variant V3 is not maintained for calendar year 2010

Hello Gurus,
I tried to load the data from data source to Targer i got bellow Error Message and i checked the data in R/3 side 2010 data is available ,
Diagnosis
An error occurred in BI while processing the data. The error is documented in an error message.
System Response
A caller 01, 02 or equal to or greater than 20 contains an error message.
Further analysis:
The error message(s) was (were) sent by:
Second step in the update
Second step in the update
Second step in the update
Second step in the update
Procedure
Check the error message (pushbutton below the text).
Select the message in the message dialog box, and look at the long text for further information.
Follow the instructions in the message.
1) Fiscal year variant V3 is not maintained for calendar year 2010
2)Error when assigning SID: Action VAL_SID_CONVERT table 0FISCPER
3)Error when assigning SID: Action VAL_SID_CONVERT table 0FISCYEAR
4)Activation of M records from Data Store object 0FIAP_O03 terminated
5)Process 000052 returned with errors
6)Process 000119 returned with errors
Please suggest.
Thanks
Prakash

prakash,
i hope 2010 fiscal variants are not mainiatined in ur bi system
please do this operation..
Go to RSA1-> source systems->select R/3 system -> right click->Transfer global settings->Fiscal year varaints->rebuild tables
then try to repeat the load...the load will be fine if the calender is maintained in R/3 if not raise this issue to the functional people...

IW32: Error getting message (Text for order header not maintain in lang.EN

Hello All,
We just starting getting this message in IW32 and IW33 stating (Text for order header not maintained in language EN) then all the pre-existing description test disappeared.
We have not done any configuration change in this particular system.
Can anyone help to resolve this.
Thanks

Hi,
As with most SAP messages it is always a good idea to trust what it is saying.
The system is telling you that KG has not been created in the English language.
Go to transaction CUNI to check the settings.
Select the Unit of measure for "MASS" (from the drop down list) and check the entries for UOMs.
KG should be there and should have an English description (the message said it was not there for EN)
If it is there and set up correctly then there might have been something else in the UOM field? You didn't enter " KG" did you (a blank character then KG?)
Steve B

Excise duty: error 9914 No material data maintained for company code

Dear all,
when executing transaction /BEV2/EDDS I get error 9914 No material data maintained for company code in some material documents.
However, I see material is correct.
Can you tell me which views of material master am I missing?
What do I need to check?
Thanks in advance,
F

Settings in material master "Basic view 1"

Query related to RM maintained for two MRP areas.

Hi PP Gurus,
The scenario is we modeled two Storage location MRP Areas say 1001 and 2001. There are two FG getting manufactured at them, say FG-1 at 1001 and FG-2 at 2001. Say there are three RMs viz. RM-1, RM-2, and RM-3. RM-1 and RM-2 included in FG-1 BOM and RM-3 and RM-2 in FG-2 BOM. Means RM-2 is common in both MRP areas.
Now I've extended FG-1 and FG-2 for respected MRP areas. RM-1 extended to MRP area 1001, and in MRP views of material master, Production storage location and Storage location for EP is maintained as 1001. Same is maintained for RM-3 except MRP area as 1001, it's 2001.
The concern is about RM-2, though I extended RM-2 for both MRP areas i.e. 1001 and 2001 but I can maintain Production storage location and Storage location for EP either as 1001 or 2001. So whenever I'm taking MRP run, for RM-2 it's either proposing 1001 or 2001 as Storage location for withdrawl or EP.
My requirement is when I run MRP for FG-1 system should show me Sloc for RM-2 as 1001 and in case of FG-2 as 2001.
As a try I tried to remove Production and Issue Sloc from MRP views and maintained Issue Sloc/Receive Sloc in PV of FG-1 and FG-2 but still unable to get the requirement fulfil.
Please make prompt comments
Thanks & Regards,
Abu Arbab

Dear ALL
my requirement is exactly same as above that i need my component to be issued from different slocs depending on diffreent MRP areas in which they are being planned.
But in my case FG is same and is being planned in 2 different MRP areas. So my BOM is same in both cases.
For eaxmple--2000 is MRP area 1 and 3000 is MRP area 2
Requirement is components should be issued from 2000 when panned in 2000 and from 3000 when planned in FG is planned in 3000.
Kindly let me know what settings are required at components level to do this
thanks

No catalog profile has been maintained for notification category

Hello
I have created the Catalog Profile with catalog code groups and assigned the codes..The profile have been maintained in technical object masters .No catalog profile is maintained for any notification type. Now when I am creating a notification M1 it says "No catalog profile has been maintained for notification category M1"...It copies the catalog profiel of the technical object after I maintain the technical object in Notification .
I want to avoid this info message..How do I avoid this message for the notifications without catalog profile...
The message details are:
No catalog profile has been maintained for notification category Z1
Message no. IM005
Procedure
Please maintain the corresponding entries for the catalog profile and allocate this catalog profile to the notification type.

Hi Shaikh,
This message can not be skipped with any SPRO settings because this message
Viz.: < ELSE.
CLEAR E_RIWO02.
MESSAGE I005 WITH I_TQ80-QMART RAISING INITIAL_REPORT_CAT.
ENDIF.>
is hard coded in program LIWO2U05.
If at all you want to bypass this message then you need to change the above mentioned program for bypassing the message.
Sundar

No Web server maintained for the presentation of log. system

Hi Banu/All,
I got the following error message while executing jump target to R/3 Transaction ME2N.
<i>Messages:
No Web server maintained for the presentation of log. system DDVR3110
Jump target cannot be executed
An error occurred with the report to report interface during the jump</i>
Banu, I have gone through the following link which u have given in the previous queries, but can u please tell me how to install ITS for the target system? or how to know/whom to ask regarding the ITS installation? is it BASIS People?
http://help.sap.com/saphelp_nw04/helpdata/en/61/b8c63ce4b79679e10000000a114084/content.htm
Apart from ITS, what other settings have to be done in this kind of scenarios?
Can U please eloborate on this topic, please?
Thanks & Regards...
Ganesh
Message was edited by:
Ganesh

Hello Ganesh,
Did you have the chance to solve it?.
I have the same issue.
Thanks in advance.
Facundo Romero.

How to check RBS maintainer is running or not and how to stop the RBS maintainer for a specific content db.

HI
how to check RBS maintainer is running after deleting orphan blobs and while deleting the blobs from rbs storage,
and also how to stop the RBS maintainer for a specific content db.
when I run below query I found the orphancleanup value true
SELECT [config_key],[config_value] FROM [mssqlrbs_resources].[rbs_internal_config]
where config_key='orphan_cleanup_in_progress'
adil

HI
the RBS maintainer was run from one of web front end server And for one content database , that fine
but I now know this information only this did by other administrators.
Now I did not found this Maintainer running in windows task scheduler, but blobs are decreasing from content database RBS storage folder, and　 also I found this maintainer running I checked from when　 run sql queriy in 　sql
server
SELECT
[config_key],[config_value]
FROM
[mssqlrbs_resources].[rbs_internal_config]
where
config_key='orphan_cleanup_in_progress’
it 　given me true
here now I want to stop this orphan cleane up , what settings and script I will run?
adil

Settings for 50% claimable is maintained for Basic, Cess, Edu Cess and Add

Similar Messages

Maybe you are looking for