Settings for Airport Utility / Airport Express

I have an Airport Express. The idea behind it is, I want to be able to take it to any hotel or location that ONLY has wired internet, and create a WiFi hotspot for my iPad.
Right now I have it set up working on my home network, but I want to make sure the settings are correct so that I could...say...take it to the Ramada Inn that only (in this example) has wired ethernet internet and plug it in, and turn the connection into a WiFi network.
What settings do I need to put in specifically for that purpose?
I'm going to Germany and I want to make sure it works before I leave.

Impossible to say for certain. The same settings used with your existing internet service provider and modem may work, or different settings may be required. An Airport Express can save 5 different wi-fi network settings which can be named for each network.
I don't travel anymore, but when I did I took my Apple PowerBook at the time with me along with my Airport Express to create a new wireless network with my AE if needed for a hotel's modem available in my room. This can't be done with an iPad.

Similar Messages

Is there any antenna for airport express?

I think i´m having problemas with the signal of my airport express and all the readings i made always refer antennas for airport extreme base station.
My question is, if there is any antenna for airport express that don´t needs an extreme base station.
Thanks
Ricardo
Pentium IV Windows XP Pro

Two quick things to check using AirPort Utility on both devices:
On your "main" base station
Open AirPort Utility - click Manual Setup
Click the Wireless tab/label located just below the row of icons
There must be a check mark next to "Allow this network to be extended"
Click Update to save your changes.
If you don't see this option, you likely have an older AirPort Extreme that does not support the "extend" feature. Please clarify on the version that you have
On your AirPort Express
Open AirPort Utility - click Manual Setup
Click the Wireless tab
Wireless Mode = Extend a wireless network
Wireless Name = Same name as your main network
Check mark next to "Allow wireless clients"
Wireless Security = Same setting as your main router
Wireless Password = Same password as your main network
Confirm Password
Click Update to save settings
If you do not see the "Extend a wireless network setting", you may have an older AirPort Express, or if you are sure that you have a newer 802.11n model, try holding down the option key while you click on the selection box to see if the "Extend" setting will appear.
Assuming no major obstructions between the main router and area that needs more wireless coverage, a good starting location for the Express would be a point that is approximately half the distance between the main router and the area that needs more coverage.
As I said, this feature works very well if major obstructions do not come into play.

HT1998 what is the latest update for Airport Express 802.11n with the Mac OSX10.6.8

what is the latest update for Airport Express 802.11n with Mac OSX 10.6.8?

You can find out as follows:
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click the AirPort Express
Click Manual Setup
Click directly on the word Version (3rd line)
If there are any updates, you will be notified.
If there are not any updates, you have already have the latest firmware.

How to find MAC address for WAN port for Airport Express 2nd Gen.

The New Airport Express has a LAN and a WAN ethernet ports. How can I find the MAC address for the WAN ethernet port as my Service Provider needs it for provisioning....I can fid MAC address for Ethernet and for two wireless 2.4 & 5GHz but not for WAN ethernet port using Airport Utility 6.1

Many thanks for the swift response. However, there is no WAN MAC address on the box or on the device anywhere. I even used magnifying glass to find one .
The airport utility shows only three mac addresses. One for 2.4GHz, one for 5GHz and one fo the ethernet (LAN port) whereas there is another ethernet port in the device mentioned as WAN port and I am still not able to find the MAC address for the WAN ehternet port for Airport Express (2nd Generation).
Will appreciate a response to make th device work wiht my service provider as providing them the WAN mac address is a must. Had there been an option for cloning mac address, the issue would have not been there.
Many thanks again - in advance.

PIN-based guest access for airport express

how do I setup PIN-based guest access for airport express?
I have a 2010 iMac OS X 10.6.8 and an Airport Express of the same era.
Thanx in advanced...
Siegfried

Hello Bob,
Thank you for your time on this. I apologize for not giving you a more complete picture of what was going on.
I should have included that I had already performed the steps that you shared and had gotten to the place where I would enter the PIN.
The problem was that, after entering a PIN that I had come up with, the "continue" button never became active. I called Apple Care and ended up talking to 3 different people before I found someone that knew the answer. The answer is that the guest computer (client) MUST be present inorder for me to complete the setup. So, problem is now solved. Thanx...
Siegfried

Mini-UPS solution for Airport Express

Hello Airport community! This is my first post.
I'm wondering if anyone has had any luck with a battery backup (UPS) for Airport Express'. I have a larger UPS for my Time Capsule which is the main access point. I've hardwired this one into the network to broadcast the same network but extend the range. If the power goes off, since a number of devices are connected to the second, I'd like to have it on back up as well. However, it's installed very in a tidier manner in a smaller area – no room here for a big APC UPS.
I've been able to find 12 V battery backups, but nothing for the Airport since it's a 120/240 V input.
Anyone have any ideas of how this might be accomplished?
Cheers,
David

As a completely different kind of solution.. Although John's battery and car inverter idea is creative.. and will work..
Use an extreme or something else that is dc powered.. You can buy a cheap second hand extreme for $30-50 on ebay or whoever has your second hand market. It can even be a different brand.. tp-link, edimax etc.. most are 12v which is excellent.. then power it down the ethernet. So you don't even need a power point.
I'm wondering if anyone has had any luck with a battery backup (UPS) for Airport Express'. I have a larger UPS for my Time Capsule which is the main access point.
Plug the 12v power supply into your UPS.. with the TC.. and buy a set of injectors for ethernet..
They look like this.
http://www.ebay.com/itm/PoE-Power-Over-Ethernet-Injector-Splitter-Adpater-Kit-/3 60843249285?pt=LH_DefaultDomain_2&hash=item5403ef0685
Just a few dollars.. they passively use the extra pairs to carry power over the ethernet wiring.. you can also buy active sets but they are more expensive but keep the line at gigabit.
http://www.ebay.com/itm/TP-Link-POE200-Power-over-Ethernet-Adapter-Kit-Injector- Splitter-5-9-12V-DC-Out-/181210762297?pt=LH_DefaultDomain_0&hash=item2a3100cc39
I have not hunted for cheapest but I have tried to keep price in mind.
There was a time when Apple used POE in the old domed Extreme.. and that was very handy.. the Express should have always had it.. it is a natural to power over ethernet rather than require power outlet next to it.

Is it normal for airport express not to show up in utility when extending a network?

Hi, with the help of this community, I think I successfully extended my wifi network by using airport expresses, connected to my time capsule, via my houses electrical system (via powerline adaptors), which ultimately connect via an RJ45 cable to the airport express. I tried to do it all with the same netwrok, so I do not need to switch to different networks when I move about the house.
I think it works because my signal strenght is much stronger than before I added the powerline adaptors. So, why am I back here?, two things. First is I want to make sure I did this all correctly, as I am adding a few more of these powerline adapters as they have really changed my wireless experiences.
What should the internet setting be on the time capsule and airport expresses. I have it set the "connection" to off (bridge mode) on the TC and the express units. But the express units blink yellow and says there is a NAT/DHCP error. something about the time capsule rejecting the sharing? so I chnage the TC to share a public address and the express to off (bridge mode), and I think this works.
But when I do this, none of the express units show up in the utility anymore. Should I just take it as a blessing that it seems to be working, and not mess with it?
What should all the setting be? I am sure that I should be able to see all the units in the utility.
Thanks if this makes any sense to you.

But when I do this, none of the express units show up in the utility anymore. Should I just take it as a blessing that it seems to be working, and not mess with it?
Did you power cycle the entire network to get things in proper sequence?
If not, power off everything....all devices....order is not important
Wait a few minutes
Power up the modem first and let it run a moment or two
Power up the Time Capsule the same way
Power up the powerline devices
Power up each Express one at a time
Power up other devices one at at time
What should the internet setting be on the time capsule and airport expresses.
The setting on the Time Capsule will depend on the type of modem that you have connected. It sounds like the "Share a public IP address" would be correct for the Time Capsule. Everything else must be in "Bridge Mode"
Each of the AirPort Express devices must be configured to "Create a wireless network" using the same wireless network name, security setting and password as the Time Capsule network. Set the Channels as "Automatic" and double check as the last configuration step to make sure that they are set for Bridge Mode.
Then restart the entire network as outlined above and you are in business.
The Express devices should definitely show up in AirPort Utility when you have everything set up.

Can't set up security for Airport Express?

Hello, we are tearing our hair out trying to set up Airport Express.
We have installed and are using the Airport Utility. We plug in the AX and it is a slow flash amber. It s being registered by our mac so we join the default "Apple Network XXX" then open Airport Utility. Checking the base station status it lists 4 items that need attention, we can work thru all of them but keep getting stuck on "Wireless Security".
We get to the point where it says select "WPA2" or "no security", we select WPA2, hit continue it then gives us the message "wireless network name is required to continue" but there is no where to select a name or enter one, the base station is also selected in the LH panel? We can't get past this point.
We have also previously in other screens already put in a password for the base station and again for the airport express - is this a 3rd password?
Any help would be greatly appreciated.
Many Thanks! - Danielle

Danielle, welcome to the discussion area!
Try the following: Open AirPort Utility and click Manual Setup
Click the Base Station tab just below the row of icons to assign a name to your device, a device password (write that down) and adjust time settings as needed.
Click the Wireless tab and work your way down the page
Wireless Mode = Create a wireless network
wireless Network Name = Your choice
Check mark next to "Allow to be extended"
Radio Mode = 802.11n (802.11b/g compatible) is a good choice
Radio Channel = Automatic
Wireless Security = WPA2 Personal or WPA/WPA2 Personal
Wireless Password = backspace to clear out anything here and re-enter your desired password
Confirm Password = Same as above
Click Update to save your settings. See if that will help.

Forgot password for Airport Express can you help?

I've forgotten my password, could someone help please?
Thanks

Try using something like a straightened paperclip or tip of a ballpoint pen to press and hold the reset button for one or two seconds - that will reset the Airport Express.
This from page 40 or thereabouts of the AE user guide:
Chapter 5 Tips and Troubleshooting
You Forgot Your Network or AirPort Express Password
You can clear the AirPort network or AirPort Express password by resetting AirPort
Express. Follow these steps:
1 Use the end of a straightened paper clip to press and hold the reset button for one
second.
2 Select your AirPort network.
-On a Macintosh, use the AirPort status menu in the menu bar to select the network
created by AirPort Express (the network name does not change).
-On a computer using Windows 2000 or Windows XP, hold the pointer over the wireless
connection icon until you see your AirPort Network Name (SSID), and choose it from
the list if there are multiple networks available.
3 Open AirPort Utility (in the Utilities folder in the Applications folder on a Macintosh,
and in Start > All Programs > AirPort on a computer using Windows XP or Windows
2000).
4 Select your AirPort Express and click Configure.
5In the dialog that appears, make the following changes:
-Reset the AirPort Express password.
-Turn encryption on to activate password protection for your AirPort network. If you
turn on encryption, enter a new password for your AirPort network.
6 Click OK.
AirPort Express restarts to load the new settings.

Setting a password for airport express

Dear all
I have had my apple ibook and my daughter's windows pc running wirelessly on the airport express for a while now. I am concerned about hackers being able to get into a) my or my daughter's computer and also b) helping themselves to our internet provider. I have tried setting a password but even so, it never asks for a password when I log on. Why is this? What have I done wrong? It is quite worrying as our computers have lots of private and banking details on them. I need an idiot's guide to setting up the ae so it always asks for a password when going on to the internt.

There are 2 passwords that could be associated with an AirPort Express (AX).
(1) Administration password. This password prevents unauthorized people from making changes to the setting of the AX. This does not protect your wireless data in any way.
(2) Wireless encryption -- WPA2, WPA, or WEP. This password is used to encrypt the wireless data so that unauthorized people can not read that data. This password would also be required to connect to your AX.
If you enable the (1) administration password it will have no effect on your ability to join the wireless network. The only time that you would be prompted for the password is when you tried to use AirPort Utility to change the settings of the AX.
If you enable (2) wireless encryption, you will be prompted for the password the first time you wireless connect to the network. If the option is enabled for your computer to remember the password, you will not be prompted for the password next time you connect. The computer will simply use the previously stored information. The wireless data will be protected from unauthorized users.

ITunes 11 hangs up on iMac looking for airport express.

Any help is appreciated, struggling with Apple issues. I have 3 airport express units set up to act as individual zones for a multi-channel amplifier in my home. The main iTunes library is housed both on my iMac running OSX Snow Leopard as well as an external network hard drive. With the latest upgrade to iTunes 11 i have noticed while directly using iTunes and through my iPad using Remote that iTunes gets lost and stops working. The screen will show that the program is trying to locate the airport express zone and you cannot close the dialogue box or close iTunes. When i view the airport utility it shows all of the airport express units functioning properly. The only way out is to manually shut down the computer and re-start. Is this an iTunes issue or possible setup issue with the airport express units. The 3 devices are in close proximity to each other feeding the amp but, functioned properly prior to the new iTunes release. Not as familiar with Apple networking and appreciate any ideas to remedy. Nothing worse than rocking out to a great tune only to have it stop mid-song with the only solution to shut down the iMac.

The same goes for iTunes 11.2.1 on 10.9.3. And it's not the first time, either. In fact, I've lost count of the number of times a software update has broken Airplay. It's immensely frustrating. If past experience is anything to go by, they'll fix it in a few months' time but until then there's nothing we can do about it. Unless someone can tell me I'm wrong?

Need Help With Download For Airport Express

Ok, computer dummy here needing help with airport express. We were given airport express last night from a friend who recently purchased a newer gadget. He told us we would need to come here to download the operating system. I see lots of links to updates but no links for someone like me who has never had anything like this on my computer before. Does anyone know what link I would need to use? We have a pc with windows XP. Thanks so much for your help!

Hello jesschambers. Welcome to the Apple Discussions!
The AirPort Express Base Station (AX) doesn't have an "operating system" per se, but it does have built-in firmware which pretty much is the same thing. In addition, in order to administer the AX, you will need the AirPort Admin Utility for your Windows PC.
Here are the links for the latest versions of both:
o AirPort Express Firmware Update 6.3 for Windows
o AirPort 4.2 for Windows

Best wifi hardware for airport express

Hi
m looking for ideas for buying the best wifi hardware (accespoint) good for running the airport express.
I have an asus wifi-onboard card right now, but the card looses connection after aprox one hour - then I have to reassosiate with the airport express.
thanks

With regards to wireless interface adapters for PCs - any make/model should work just fine. If you want to try an alternative, stick with a product from one of the big names in the business of making these adapters like Linksys, Netgear, D-Link, or Intel.
That being said - there are common causes for "dropped connections" other than a "bad card". Interference from neighboring wireless networks and 2.4 GHz portable phones, for example, will also cause problems exactly like you describe. Before replacing the card, you might experiment with changing the wireless channel of the Airport Express (try 1 or 11) - a setting found under the Airport tab of the Airport Admin Utility.

How do you configure the a network for Airport Express from a PC computer

A friend let me borrow her Airport Express so I could have wireless, but I can't figure out how to set up the network from my PC computer. She just gave me the device without any accompanying instructions or software. The intructions online only explain how to setup the network using an Apple product. How can it be done from a PC?

Use the same instructions and the Windows version of AirPort Utility:
AirPort Utility 5.5.3 for Windows

Unable to open configuration for Airport Express after update 5.3.1

I can still reconfigure my Airport Express unit using the old version of the Airport Admin Utility.app version 4.2 under OS 10.4.11 that remained after the update. But the new AirPort Base Station 2008-001 update version 5.3.1 for Tiger will not allow me to access the configuration. It comes back with an error even though the Airport Express unit is recognized by the new software. The message reads: "An error occurred while reading the configuration".
Why won't the new version work? I tried rebooting the Airport Express unit and even unplugged it for 60 seconds. This did not help.
About 6 months ago, I had to revert to an older version of the firmware to stabilize the system to version 6.1.1.
Airport has really been touchy. And each update of the OS does not seem to help.

Hi,
My old Saucer Expresses work with Firmware 5.6, though it wants to update them to 5.7.
Does it ask for the Password/Keychain usage? If not, might trash that Keychain... or Factory reset it too.
Might just try the latest...
http://www.apple.com/support/downloads/airportexpressfirmwareupdate63formacosx.h tml

Settings for Airport Utility / Airport Express

Similar Messages

Maybe you are looking for