Setup for Panasonic PV-GS400 with 12-bit audio

I've some tapes recorded in 12-bit audio. What do I select under easy setup to avoid audio/video sync error messages later on?
Moving ahead I will use 16-bit audio on the DV cam. What settings do I alter?
Thanks - basic stuff I know - just gt FCE.

Hi
I'm a lucky bloke. I got a wife with a second Camera.
Camera owning friends. If just a few tapes it could be a reason for a nice
come together.
Yours Bengt W

Similar Messages

Exporting from PPro CC - Exporting using Match Sequence Settings issue with 24 bit audio

I am having an issue exporting my sequence which contains final AIFF mix (24 bit 48 kHz) into a 'same-as-source' ProRes 422 file with 24 bit audio. I am specifically trying to export media with 'Match Sequence Settings' checked to create an identical output of what my sequence is. I wind up only creating a PR422 with 16 bit audio rather than 24 bit audio.
My sequence contains ProRes 422 media and 24 bit AIFF final stereo mix (1 audio file) from our Sound department.
My sequence is currently setup as "Custom" at 1920x1080, 23.976 fps, Square Pixels, Progressive, etc. Audio is 48 kHz (I don't see an option for choosing different bit rates in the 'Sequence Settings').
Using 'Match Sequence Settings', my options to alter the audio are "greyed out" and unavailable. I'm not sure why 'Match Sequence Settings' doesn't recognize that I am cutting with 24 bit audio and, instead, only exports 16 bit audio.

Always skip Match Sequence Settings and set up the export manually.

Optimal Setup for New Time Capsule with Wireless AC

I'm curious to see what the hypotehtical optimal setup for my Time Capsule. I understand that wireless speeds depend on a ton of factors and that part of getting the best connection is just trying different options. I have a new Time Capsule that's connected to the following devices: iPhone 5S; new MacBook Air with wireless AC; old iMac from 2007; old AirPort Express that only supports b/g and a newish Apple TV that supports wireless N, I believe. I was connecting to the network (which was not designated with the 5ghz) and I recently chose the option to label the 5ghz. I'm using that now to stream music with the new iPhone and the Apple TV with no problems, but I have no longer have the option of using the old Airport express because it's an old one. I'm thinking of just getting a new Airport Express and leaving it at that, but wanted to know if anyone has some thoughts on this. I'm sure there's a more concise and direct way to ask this question, but my knowledge is pretty limited here. Thanks in advance.

The Time Capsule is already set up for optimal performance when you open up the box.
You can assign a separate name to the 5 GHz network and point devices that are capable to that network. This works well if the device is located close to the Time Capsule.
But, 5 GHz signals are much weaker than 2.4 GHz signals, so once you move a room or two away, or the signal has to pass through several walls, the 2.4 GHz will be stronger.....and probably faster as well.
But...your device will try to stay locked on the 5 GHz network since you set it up that way.
This type of setup may or may not work best for you. For most users, it is simpler and more effective to use the default settings on the Time Capsule to have both bands use the same network name.
Then, your wireless devices will automatically connect to the signal with the best quality. Best quality may not be the fastest signal since there are lot of factors involved with signal quality. But, if you think about it a bit more, don't you want to have your wireless device connect to the signal with the best quality?
Some users swear by assigning a separate name to the 5 GHz band. I'm not one of them, but If it works well for them and they are happy, then there is no reason to change.
An older AirPort on your network is going to drag down the speeds. You need the new AirPort Express, or better yet an AirPort Extreme if you want to be able to extend the new 802.11ac signal.

HT4557 whats the best itunes/appleID setup for family of 3 with 3 ipads, 3 iphones, one PC with all music on. if we use 3 separate ones how do we share purchased and home content?

been with apple for years. one itunes/appleID in use for family - all purchases and downloads on the one account..
now got 3 ipads, 3 iphones and when we update the software, we seem to get text/facetime issues due to multiple email addresses and phone numbers for the different devices that each individual uses. For example, I send a text and it appears to have come from my wife or son to the recipient. Not good !
there seems to be direction from apple that each of us should use our own apple id, thogh how do I link the accounts so enable family sharing of music/media we have purchased etc - Id also like to be able to review and keep a private eye on what my son downloads as he is 11 yrs old ! I manage this currently as we allow him access to the password for itunes (as we all use the same id today)
Am i better setting up accounts for my wife and son independent of my own, or not. Each of us would like access to the family content we have and the master library of synced content. I just want the most simplistic approach that apple, or others would recommend.
Is there a better or optimum setup for a family as we cannot be alone.....

Thanks for the help, but a follow up question now.
My iPhone won't arrive for a little while, but my wife already got hers and she wants to set it up now. Using my Apple ID for the purchases, if she starts setting hers up, can she change her iCloud ID to something else quickly? It keeps telling us that we have to sign in with the AppleID first.
Should we just set up an iCloud account via normal internet before trying all this via iPhone?

Network Setup for a 1232AG config with multiple AP's

I'm looking to deploy a temporary outdoor network using 1232AG radios, with only one radio connected to Ethernet & Internet. All the other radios will have a A radio connection to the parent. And their
G radios will advertise for Client Access. Ultimately I'd also like to have the local ethernets active on each of the remote Radios, so that a switch could be setup for people who don't have Wireless.
So the questions, Is this type of setup even possible? If I use the A radios for back haul, and the G radio for Client Access, does the Ethernet get disabled?
What station-role in the network should each of the radios play. Ultimately I believe we could have different SSID's and IP Subnets for each AP, but if we kept them all the same, can we make this one big Bridge? So that someone can Roam between AP's. Granted I don't have the funds for Wireless Lan Controller. Sugestions?

So what you are trying to do is have some sort of MESH outdoor wireless, but using the 1232AG? Don't think you can do this by using the bridge role. You would have to go bridge to bridge and then have an ap connected to one of the bridge to handle users...

ArrayIndexOutOfBoundsException with 16 bit audio

Hi, when converting 8 bit audio I have no exceptions, but when converting 16 bit I get an AIOOBE. Here is the code segment that deals with the conversion:
try {
for (int r=0; r < audioShortData.length-1; r++) {
    loByte = audioByteData[r * numChan + 0];
    hiByte = audioByteData[r * numChan + 1];
    //convert bytes to int
    sample = (hiByte << 8) | (loByte & 0x00FF);
    //samples array
    audioShortData[r] = (short)sample;
} catch (Exception ex){ex.printStackTrace();}The exception is pointing to: loByte = audioByteData[r * numChan + 0];
Thanks!

My proposal:
try {
for (int r=0; r < audioShortData.length; r += 2) {
    loByte = audioByteData[r + 0];
    hiByte = audioByteData[r + 1];
    //convert bytes to int
    sample = (hiByte << 8) | (loByte & 0x00FF);
    //samples array
    audioShortData[r/2] = (short)sample;
} catch (Exception ex){
ex.printStackTrace();
}Just a quick guess, I'm pretty sure I can't think straight anymore right now.

Easy Setup For Panasonic AG-HMC150 Files?

I just got my new Panasonic AG-HMC150, and shot some sample footage at 720p/60. I had no problems getting the clips into FCP using Log & Transfer, and they look fine when playing them in the viewer, or from the timeline.
I have a Matrox MXO, and the clips also play great on my 2nd Cinema Display that runs off of the Matrox; and, I have a small Sony 4:3 CRT monitor, that shows the clips properly letterboxed, and they play fine on that too. I've even exported the clips to Compressor, and burned a DVD in DVDSP, which looks great. Audio is fine, in sync, etc.
The only problem is in the FCP canvas window; the lips will flicker a little or a lot, depending on the View Menu's video playback setting; using MXO DVCPRO 1280x720/59.94 causes a lot of flicker, while choosing MXO Uncompressed 1280x720/59.94 causes a little .
I'm not sure if my Easy Setup is correct; I've chosen the MXO Apple Pro Res 720p/59.94 sequence setting, but I'm not sure what to do for Capture or Device Control settings; I wouldn't think that they would matter.
I think the problem is with the Video Playback setting; I've chosen several of the MXO settings, and they all play fine on my Matrox monitor, but I can't find one that will smooth out playback in the canvas. Or, since everything else seems to work fine, should I even be worrying about this?
I'm making the switch from capturing tapes, and I actually expected a lot more trouble than I'm having; but solving this tiny glitch would be great. I'm looking forward to getting familiar with this camera and using it for some upcoming events.
Any suggestions on the proper Easy Setup settings for files from this camera, and in particular, a good View/Video Playback setting? Thanks in advance.

Click on one of the ingest camera files in the FCP Browser. Once it is selected, type Command + 9 to see the properties for the clip. Either report those properties here or take a screen shot of the item properties and post that here.
Next, click anywhere in your timeline, then type Command + 0 {zero} to see your Sequence Settings. Either report those settings here or take a screen shot of your Sequence Settings and post that screen shot here.
MtD

How do I install Elements for Windows 7 PC with 64 bit? Get error message - file archive part missing

We purchased Elements 12 and Premiere Elements 12 on September 7, 2014 and have tried a variety of things including searching through FAQs on the Adobe site, etc. etc. and cannot get our downloads to work. We are avid computer users and have never had problems downloading software before.
From our account under "orders" - I have tried clicking on the Akamai download manager and the Alternate Download Method on for each application with the same results.
We have a Windows 7 PC with a 64 bit operating system and Internet Explorer 11.
On all attempts we get an Adobe screen with 2 links – 1 for a file ending in .7z and a 2nd file ending in .exe.
I click on the first file and confirm the download completes at 100% (not paused, etc.) and is in the downloads folder for my user name on the PC.
I click on the 2nd link for .exe and I receive the error message below – 2nd screen shot – “file archive is missing” all folders/files must be in same folder.
So I see it’s a winzip file (as a winzip pop up folder had come up also) so I download the free version and unzip the files in the same downloads folder under my user name to try that.
I click on .exe file link again and same message. I tried copying the files directly to the downloads folder (as they all unzipped into a subfolder called PSE 12 and tried clicking on .exe again but get the same message.
For Premiere I tried the same and got same results on the 64 bit version download.
I do not know how to access the software we purchased.
Any help or advice is appreciated.
Also - if anyone knows how I can contact Adobe for a full refund so I can just buy the boxed software instead - that would be helpful as well as that is not easy to find online either.
Thanks!
Ariel

I get an error message saying that the quicktime installer will only work on 32 bit
The QuickTime player works on 64-bit systems. (It's a 32-bit application, but it should run fine using the standard 32-bit-on-64-bit Windows-on-Windows emulation.)
What's the precise text of your installation error message, dc? (There one or two different ones I can think of that might mention 32-bit)

Step by step complete setup for WRT54G ver.6 with Laptop and XBOX 360

Hello. I am sorry to post this, I am sure it is a juevenile and redundent question...but I have tried to look for the set up cd (I can find where to download it...though I can find the firmware upgrade or whatever). My friend at work said it would do all the setup pretty much automatically for me.
I somewhat know computers, but you might go ahead and make your replies VERY lamen's terms or I might not be able to follow. Anyways, what I need, is a step by step/screen by screen directions for a secure network. I have made a partial attempt at setting it up and it technically works, but I would feel better if I did the steps a-z in order, so I know that it is done correctly. I also am not totally confident in its security as it is now. (Also, technically, I did not check the XBOX again after getting the new laptop, I am just assuming it is still working because it was before).
My problem is I can't seem to find very good directions for setting up the router...I only find partials or confusing directions.
So here are the things I am trying to connect:
Liksys WRT54G ver. 6
Gateway Laptop running Windows Vista
XBOX 360 - WIRED
(I had a PC and a laptop, but they both died at the same time and I have only been able to replace the laptop at this point...the PC will come later and not sure at this point if it will be Wired or not).
I have a cable Modem between the Router and the wall...I didn't look at that for brand/etc...but I can get it ASAP if needed.
Here are the settings that I have so far:
Changed the Router Name
Changed the SSID
Have DHCP set to 3 (XBOX, PC, Laptop)
Wireless SSID Broadcast: Disable
Username and Password changed to my own info
UPnP: Enable
I may have changed other things without knowing it. So like I said, a complete, step by step screen by screen set up would be totally appreciated. I haven't done anything in the security tab, all that is totally foreign to me, so I am just not broadcasting for now until I can get some help setting things up with you guys.
And if someone is familiar with the Laptop/XBOX 360 setup, and I need to change any of the settings on the XBOX itself, could you please include that in your directions? I know that isn't technically what THIS forum is for, but it would sure be helpful to me if you happen to know both parts anyways.
Thanks a lot (in advance)!

So all you just need to do is, secure your Wireless Network. Follow the setps bellow and change the settings on your Router.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
- Wireless Network mode should be mixed...
- Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
- Set the Wireless channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WPA, For Encryption, select TKIP...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone and remember the key.
NOTE : Passphrase should be more that 8 characters...
Now see if you can locate your Wireless Network and attempt to connect...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
Now see if you can locate your Wireless Network and attempt to connect...

Configuration/Setup for securing PI messages with certificates

Hello Experts,
I'm looking for some guidance/suggestions/direction in regards to installing and using certificates when exchanging data with trading partners via PI 7.0. It's something new to us and it's been a bit of a struggle.
In scenario 1, we want to send to, and receive from, xml documents with a partner. We currently send from our PI system, but want to receive the messages back thru an F5 network (?) which would decrypt the message and pass it along to PI. This also takes care of load-balancing.
In scenario 2, we want to exchange EDI messages using the AS2 Adapter from Seeburger. Again, messages would be sent from PI and received by the F5 network.
The F5 would act as the SSL termination point (if that's the correct term), and pass the decrypted message to PI via a normal http transfer.
We are storing our partners' certificates within PI, and configuring the communication channels to use them. Is this correct? Do they need to be stored on the F5 as well? Do we then give them our certificate from the F5, or do they need a certificate from our PI server, or both?
I guess what I'm looking for is some straight-forward SSL 101 documentation, especially where it applies to middleware like the F5. Thanks in advance for any help you can give.

Hi,
Just a quick note on the certificates; if you want to encrypt messages sent from PI you need the public key of the receiver stored in PI (J2EE key store) with which to encrypt the messages. When receiving files back from partners, they would need to encrypt the messages with the public key of F5 certificate. F5 would then use its private key to decrypt the message before passing to PI.
So, yes, you are correct to store the certificates of your partners in PI which will be used in encryption of outbound messages. F5 would only need the private keys of the certificate that your partners have encrypted with, no need for PI certificates to be stored in F5 (unless you also need digital signatures).
Hope this helps.
Br,
Kenneth

Redundancy and Failover setup for 2 MPLS link with 2 different countries

Hi Sir/Madam,
We have 2 MPLS link and both links are active (from COUNTRY A to COUNTRY B) and we also have 2 partners who are located in COUNTRY B with same building but with different offices and each partner will be using each MPLS link. For example, PARTNER A will use the 1st MPLS link and PARTNER B will use the 2nd MPLS link and we want to have a failover setup (please see sample design below). What is the best solution for COUNTRY A and B to have a full redundancy and failover setup/network?
Any recommendation and sample configuration will be a big help for me. Your feedback is highly appreciated.
Thank you in advance.
Best regards,
Marvin

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
MPLS links, eh. You mean your MPLS facing ports have actual MPLS labels? Or do you mean your WAN links are running across a MPLS network, but the handoff isn't MPLS?
Country A's two routers are your company's devices? Do you have interior connectivity between them?
Country B's two routers - do they or can they have interior connectivity?
What routing protocols are being used (and where)?

Spotify 1.0.11 beta for Linux is out, with 32-bit binaries!

Hello Linux users!
Today we've released Spotify client version 1.0.11 for Linux. There are some big changes in this version, and it's still considered to be a beta release, and will be in beta until the items in the "known issues" list below are resolved. If you want to try out this version, installation instructions remain the same as for the other betas:
echo deb http://repository.spotify.com testing non-free | sudo tee /etc/apt/sources.list.d/spotify.list
sudo apt-get update
sudo apt-get install spotify-client
or if you have a previous version installed, simply:
sudo apt-get upgrade
Since the previous public release (version 1.0.9), we've made the following Linux-specific changes:
32-bit binaries are now available! Now users on i386 systems can try out the 1.x betas as well. Please reply to this thread with any technical problems that you encounter on that architecture.
libnotify is now an suggested package dependency. If you don't have that library installed, this feature will simply be unavailable.
Updated application icon in the spotify.desktop entry
GPU acceleration is disabled (see below)
This build ships with the following limitations, of which we are still currently working on:
Proper dbus support for MPRIS MediaPlayer2
There is no application menu
It is not possible to re-enable GPU acceleration through the settings
Important: regarding GPU acceleration, this is now completely disabled in the client, and we do not yet have a way to enable it in the preferences. This change was originally made in Chromium for Linux, but since the Spotify client uses CEF, we inherited this change from them. According to the Launchpad bug report, faulty GPU driver support was the single largest cause of crashes for Chromium on Linux (this graph shows how Chromium crashes on Linux have dramatically decreased after the setting was changed).
Depending on your hardware and GPU drivers, this change is either going to be a big annoyance for you or a huge blessing. For our users who experienced frequent and strange crashes with the client, this change will probably greatly increase client stability. For other users with certain video cards, scrolling performance and redraw rates may be noticeably choppier. Some users won't notice anything at all.
The obvious solution here is that our Linux client needs a toggle to manually re-enable this feature in the settings. Exposing this feature is not as straightforward as you might believe, or else we would have done it already. ;) However, we're working on a way to do just that, and hopefully will have something in place for the next beta release.

nikreiman wrote:
blubbo wrote:
Thanks for your continued support for Linux! It _is_ appreciated! :) Any chance the queing over Connect is gonna be looked at soon? The windows client seems to only be able to queue one song. If there already is one song in the queue nothing happens when you try to add another (except for the weird reshuffling that happens whenever you touch the queue). And if there are more than 1 song queued, the windows client removes all but the first one. From Android it works almost always. This is the only complaint I have with the Linux version but it's kind of a deal breaker when using it soley as an headless music player.This sounds like a bug, and a non Linux specific one at that. I'll look into this, however there are some changes to the player stack which will also effect connect that we are just rolling out. These changes will not require a client update, so there is a chance that you'll notice this behavior "magically" fix itself in the upcoming weeks. Anyways this is not a known limitation from our end for Linux users, we will investigate this bug.Good. Controlling -> PlayingWindows -> Android: Queing in itself works. But the queue gets cleared when the first song in it starts playing.Windows -> Linux: As explained above.Android -> Windows: Queing in itself works. But the client shows information for the song directly after the queued songs.Android -> Linux: Queing in itself works. But the client shows information for the song directly after the queued songs. So ... abrakadabra? :)

Easy setup for Panasonic AG-HMC40P

I have the camera settings to capture at 1080/60i. I burn to regular DVD, not blueray. Can you please tell me what the easy setup should be in FCP? Once I'm finished editing in FCP, I output to QT movie and then into iDVD.

Click on one of the ingest camera files in the FCP Browser. Once it is selected, type Command + 9 to see the properties for the clip. Either report those properties here or take a screen shot of the item properties and post that here.
Next, click anywhere in your timeline, then type Command + 0 {zero} to see your Sequence Settings. Either report those settings here or take a screen shot of your Sequence Settings and post that screen shot here.
MtD

Lost RAW format for Panasonic DMC-LX1 with new version 1.5.3 !!!

Hi,
Aperture 1.5.3 tells me it doesn't understand the RAW format of my Panasonic DMC-LX1, when it used to in 1.5.2.
Anybody has any idea how to restore this ???
Thanks,
Richard
MacBook Pro 15.4" Mac OS X (10.4.9) 1 GB RAM, iPod 60

Actually Aperture doesn't support the RAW format of this Camera !

Wireless setup for deskjet 3050A - windows vista 64-bit

When attempting to set up wireless printer it advises to temporarily connect a USB cable. When I do this the computer hangs and won't advance. The first time I attempted to install it said my password was wrong. I've not been able to get back to that point where it asks for a password. I've tried re-installing, restarting, etc. and nothing seems to work.

Hi Bhyte,
For Windows,
Here is the link to download flash player for Plugin based browsers.
http://download.macromedia.com/get/flashplayer/current/licensing/win/install_flash_player_ 15_plugin.exe
Thanks,
Nikhil Gupta

Setup for Panasonic PV-GS400 with 12-bit audio

Similar Messages

Maybe you are looking for