Setup Hotline Analog Phone with SCCP
Anyone out there can help me out how to setup a hotline in CUCM 8.6?
I've followed this procedure below, but I'm still getting an error message when I lift the handset such as "your dial cannot be completed...".
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_configuration_example09186a0080232b9f.shtml
Just in a nutshell, here is what I've done:
Extension: 1111 PLAR Analog SCCP Phone with: CSS_Hotdial and PT_Allowed (line settings)
TP: blank, PT_Hotdial and CSS_Hotdial, and called PTM: 2222
Extension: 2222 CSS_Allowed, and PT_Allowed - no changes on this extension...
Added the PT_Allowed into CSS_Hotdial. The order is: PT_Hotdial/PT_Allowed
Both lines are on the same VG204-vg20x-ipvoice-mz.124-22.T5.bin. When I selected hotline feature it says is supported Analog Phone SCCP, but I did not see the VG. It looks like is not supported hotline on VGs. Can someone confirm that?
Am I missing something? Do I need to enable something under Service/Enterprise parameters?
Thank you!
Chris, thanks for your prompt help.
I thought the TP needs a CSS with access to the 1111 DN, not to the 2222. Because when someone lifts the handset on phone 1111 this phone should invoke the TP which translate and ring to the 2222 phone. Thus, I put this CSS_Hotdial on phone 1111 under line.
And my TP looks like this: PT_Hotdial and CSS_Hotdial, and called party transformation mask 2222
The CSS_Hotdial has only access to one PT_Hotdial.
Also the two phones 1111 and 2222 are on the same partition PT_Allowed, but they are on different CSS.
Anyway I also tried what you said but did not work. Are you sure this hotline works on VG204? I think it is not working because this feature is not supported on VG204 nor in any VG model.
If you are sure it should work. Could you please elaborate more this solution with PT/CSS/TP?
Once again thanks
Similar Messages
-
We have analog phones in certain applications that use a neon light instead of a ring tone. It requires 90v to activate the neon light. We have VG224 analog gateways which appear to not be able to push 90v. Does anyone have a solution or is there another Cisco gateway that will support analog phones that use a neon light instead of a ring?
BlackBerrys have a flashing red LED indicator light for new messages. It's hard to miss. And with the sleeve cases, there is a gap for keeping this notification light visible, even when holstered.
-
VG224 box & analog phones with CCM3.3 - call problem
Hi
We have CCM3.3 at central location & at remote location with 2mb leased line have router & connected to LAN then VG224, analog phoenes.
Initially VG224 not reg, then it got reg with use of h323 procol config at both CCM & VG end.
Now 2 analog ph are connected at VG end and tring to call IP phone number which is got reg with CCM3.3.
Result: from analog ph able ring IP Phone but Ip phone cannot. And one more is from analog to IP Phone is one way, call initiator is getting voice from IP Phone. but IP Phones not able to hear anything.
Need solution & troubleshoot for the same.
Regards
Naga.Hi,
try removing voice-class and use "codec g711u" instead under DP 4000.
Hope this helps, please rate post if it does! -
Cisco VG 224 Analog Phone Gateway
Hi
Can i use cisco vg224 gateway in a scenario like -
cisco ISR+CCM express -->WAN LINK --> cisco ISR -> VG224 gateway --> analog phones.
If this scenario is good then, can i do call transfer and forwarding with analog phones with any extensions digital/analog on that setup?
thanks
regards
Rakesh
=====The Cisco VG 224 is an analog voice gateway that manages up to 24 FXS ports for analog devices. Call control of the analog FXS ports is provided by Cisco CallManager or by a Cisco CallManager Express (Cisco CME) system. An SCCP telephony control (STC) application on the Cisco VG 224 functions as a a proxy to translate call-control messages between the call-control system (Cisco CallManager or Cisco CME) and the voice gateway.
This URL should help you:
http://www.cisco.com/en/US/products/ps6441/products_feature_guide09186a0080483a76.html
http://www.cisco.com/en/US/products/ps6441/products_feature_guide09186a0080483a76.html -
MWI on analog phone using stutter dial on VG248
Someone is telling me that you can use stutter dial or some other method to light up an anolog phone Message waiting indicator using on a VG248. This is with an analog phone that has an Message light on it. Is this possible and if so is it possible using and ATA with Call Manager?
Hi Shane,
This does work with the VG248, we have used the "Stutter Dial Tone" on some analog phones and used the actual MWI Lamp on other analog phones with good success. Have a look;
Choosing Message Waiting Indicator Type
The VG248 supports several types of methods for sending MWI messages to analog phones. Because you might have different types of analog phones connected to the VG248, you can modify the MWI type on a per-port basis. So, if you have some analog phones that have MWI lamps on them, you can notify users of awaiting messages using the lamp. Or, you can choose to play a tone when users pick up their phones.
Keep in mind that the VG248 only sends this information to the phones if it is received from Cisco CallManager. If Cisco CallManager is not integrated with your voice mail system, it does not send this information to the VG248.
Step 1 From the main menu, choose Configure.
Step 2 Choose Telephony.
Step 3 Choose Port specific parameters.
Step 4 Use the arrow keys to select the port to configure and press Enter.
Step 5 Choose MWI type.
Step 6 Choose from the following options:
Lampilluminates lamp on phone
Caller IDuses caller ID mechanism to send MWI messages to the LCD screen on phone
Stutterplays tones when user picks up the phone
Lamp + stutterilluminates lamp and plays tone
Caller ID + stuttersends message to LCD screen and plays tone
Nonedoes not send MWI information
From this doc;
http://www.cisco.com/en/US/products/hw/gatecont/ps2250/products_configuration_guide_chapter09186a0080087de4.html#xtocid13
Hope this helps!
Rob
Please remember to rate helpful posts.......... -
How to config CME with FXS card for analog phones
I want to config FXS cards in CME router with SCCP protocol for transfer, pickup ... feature. I can find information about the sccp (the command about stcapp), but I can not find the information about how to config CME, e.g. the phone no.(something like ephone-dn .... )
Can anyone help me ? or send me the link
Thx
DennisThx Johncaston,
Your config is for H323, it doesn't support features, something like transfer funtion .......
I have found the config for SCCP, let's share my finding
====================
ephone-dn 178
number 9933
description Board Room
name Board Room
hold-alert 30 originator
ephone-dn 179 dual-line
number 9990
description Meeting Room 3
name Meeting Room 3
hold-alert 30 originator
ephone 95
mac-address 9556.60FA.0200
type anl
button 1:178
ephone 96
mac-address 9556.60FA.0201
type anl
button 1:179
GigabitEthernet0/0 is up, line protocol is up
Hardware is MV96340 Ethernet, address is 0019.5566.0fa0 (bia 0019.5566.0fa0)
================================
stcapp ccm-group 1
stcapp
sccp local GigabitEthernet0/0
sccp ccm 172.16.136.125 identifier 1
sccp
sccp ccm group 1
associate ccm 1 priority 1
signaling dscp af31
audio dscp ef
voice-port 1/0/0
cptone HK
caller-id enable
voice-port 1/0/1
cptone HK
caller-id enable
dial-peer voice 21 pots
service stcapp
port 1/0/0
dial-peer voice 22 pots
service stcapp
port 1/0/1
=========================
Thanks !!
Dennis -
Pick up group between analog Phone connected on VG224 with Cisco 7911 does not work?
Hey guys,
I had a problem, during a demo. My team was design a cisco callmanager 7.0 with 7911 IP Phone and with VG224 analog devices phones. I would like to know if there are some a problem of capability when configured a Analog Phone on VG224 in the same pickup group with Cisco IP Phone 7911.
I got pickup between Analog phones but with I cannot pick up, between IP Phones and analog phones.
Does anybody knows if has capability problem or could be a configuration problem.
The feature has already enbled for pick up **3 (stcapp feature access-code).
best regards
DanielHi Daniel,
Did you try **4
The default settings for the VG224 feature codes are as follows:
Call Forward All (CFA) **1
Call Forward All Cancel **2
Call Park Directed Call Pickup Directed **6
Call Pickup Group **4
Call Pickup Local **3
Call Transfer = Hookflash
Redial *#
Speed Dial *01 to *99 for two-digit codes
Speed Dial to Voice Mail Default prefix and code is *0 for one-digit codes, and *00 for two-digit codes
http://www.cisco.com/en/US/docs/ios/12_4t/12_4t2/ht1vg224.html#wp1178205
Hope this helps!
Rob -
Vg224 don't auto disconnect with analog phone
Dear all ,
why vg224 don't auto disconnect with analog phone? is the busy frequency dismatch between vg224 and analog phone?
can you have any suggest to me ?
thks.HI rrjoas45,
thks your answer, I try to add a command with supervisory . but I discovery it isn't effective . the port status follow:
sh voice port 2/0
Foreign Exchange Station 2/0 Slot is 2, Port is 0
Type of VoicePort is FXS
Operation State is DORMANT
Administrative State is UP
The Last Interface Down Failure Cause is Administrative Shutdown
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 64 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 250 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Supervisory Disconnect Time Out is set to 750 ms
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for CN
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Analog interface A-D gain offset = -3.0 dB
Analog interface D-A gain offset = -3.0 dB
FXS idle voltage set to high
Ring DC offset set to 0 volt
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
Voice card specific Info Follows:
Signal Type is loopStart
Ring Frequency is 25 Hz
Hook Status is On Hook
Ring Active Status is inactive
Ring Ground Status is inactive
Tip Ground Status is active
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Hookflash-in Timing is set to max=1000 ms, min=150 ms
Hookflash-out Timing is set to 400 ms
No disconnect acknowledge
Ring Cadence is defined by CPTone Selection
Ring Cadence are [10 40] * 100 msec
Ringer Equivalence Number is set to 1
thks. -
I have an iphone 5. My number has not transferred over to the new phone although my network provider sais that it has. The network provider sais I must setup phone with itunes. How do i do this?
If you can access anything on the phone, then try a reset. Hold the sleep/wake and home buttons together until you see the Apple logo and then release. If this doesn't help, then go to Settings, General, Reset, Erase all content and settings, and this will bring you back to the activation screen.
-
Analog phones couldn't communicate with ip phones in an internal lan
As you can see in the above picture, i have a astrick server 1.6.2 and cucm 7.0, spa and isr router.
when im calling from ip phone to analog phone call is successful , but when Im calling from analog phones to ip phones call is not successful.
only one way communication is happenig in this scenerio i.e from ip phones to analog phones.but vice versa is not working why ?
can any one slove my problem i will glad and thanks for reading my post.Kiran,
1. Who handles those analog phones ( CUCM or Astrick ) ?
2. Did you check the routing on the ISR ? Usually one way audio is experienced due to missing ip route. Please ensure you have the route in place for both directions.
3. What is the integration type between CUCM & Asterisk ?
GP. -
SPA9000 + SPA492 + analogic phone: Cancel Request doesn't work
Hi all, I'm build up a LVS in the following configuration: SPA9000 + SPA942 + analogic phone on FXS1; PBX connected to LAN with WAN interface and IP phones on the same LAN at all; "Force Media Proxy" parameter = "yes"; "Line 1" in trunk with an ITSP; no NAT parameter changed from default; WAG54GP2 on ADSL as Internet gateway in standard configuration. All seems running fine, except for one small but really fundamental function: I start an outbound call from SPA942 or analogic phone, the addressed phone rings and if I hung up before the call is accepted, the phone on the other side keeps the ringing up. In my opinion, it seems like a failed "Cancel" request. If I try to do the same with the analogic phone conected to WAG54GP2 all runs well, so I can exclude a signalling problem of the ITSP. Thanks in advance for your help.
Several things to try -
1) Set NAT mapping and NAT Keep Alive to yes on the SPA9000 line connected to the ITSP.
2) Setup port forwarding on the WAG54GP2 to forward port 5060 to the IP address of your SPA9000.
3) Replace the WAG54GP2 with a standard modem and connect the SPA9000 directly to it. -
I shared itunes account with daughter's phone, never synced my phone with home computer through itunes, synced tonight with itunes but choose her iphone and it restored all her info on my phone, all my phone contacts, text messages and photos are gone - I had auto backup to icloud daily - is there any way to get phone numbers and texts back off icloud?
If you have been backing up to iCloud your camera roll photos, text messages and other data and setting should be contained in the backup. Restoring the backup to the phone should recover them.
To do this, go to Settings>General>Reset, tap Erase All Content and Settings (which will erase the phone), then go through the setup screens on the phone and when given the option, choose Restore from iCloud Backup and follow the prompts. Be sure your phone is connected to wifi and your charger as this may take some time to finish. -
Setup as new Phone Or Restore From Backup Everytime!!!
Dear All,
Firstly thanks for your help in advance to anyone who can shed some light on the below problem.
I am now on my third iphone as had each model as they have been launched.
I currently have two active phones,
One is my company phone iPhone 3Gs (Business)
The second is my personal phone iPhone 4 (Personal)
Whenever i attempt to sync either phone to my laptop, (Acer 5942G (windows 7)) itunes always presents me with the, "Restore from a backup or set up as new phone" screen.
This happens everytime for both phones. I have to setup as a new phone and re-sync all my apps etc etc. Its such a chore .
I don't sync either of my phones with any other device, ever!
It is starting to get on my nerves so much.
Please could somebody shed any light on this issue or is anyone else having the same problem.I too have this very frustrating issue. It worked fine 2 weeks ago.
I have two devices setup, and they have the same name, but that has never been a problem as one is a 5G 80GB iPod, and the other is an iPhone 3GS.
Now, everytime I plug my iPhone into my PC, iTunes comes up and asks me to restore.
Grrr... I have restored 3 times. I have also performed a complete iPhone reset and a restore... same thing, and I have no idea why.
Please help.
Thanks,
S. -
How do I set up two phones with the same Icloud account
I have 2 Iphones for my daughters and want to use the same Itunes account and Icloud account but when I set it up on the 2nd phone it uploaded the other phones contacts and the new phone is receiving the 1st phones text message. do you have to set up a separate Icloud account to prevent this from happening?
Phone A = phone with information you want duplicated
Phone B = phone that you want to copy from A
Backup Phone A.
Wipe Phone B using these instructions. What to do before selling or giving away your iPhone, iPad, or iPod touch - Apple Support
Phone B should be on the 'Hello' screen. Do not swipe it. Launch iTunes. Plug in Phone B.
When iTunes asks if you want to set up as new phone or restore from backup, choose restore from backup of Phone A.
After this setup, any changes to one phone (i.e. adding a contact, downloading an app) will have to be manually duplicated on the second phone, if that is your desire). Making changes to one phone will not affect the other after setup. -
How do I transfer data from my phone with the bluetooth to my Mac??
Hey,
I heard from a friend I can send my phonebook/phone data through blue tooth to my Mac.
My phone is currently broken and I don't want to lose the data. I know I can text it through,but I can't with my phone right now-is there a way to set up the blue tooth and like transfer it straight to my Mac,besides texting it?
I've never even used a blue tooth to my phone. So any explanation/steps to do this?
Thanks.What is the manufacturer of your phone? Can you look the instructions up in your phone's manual or search the website of your phone's manufacturer? Irregardless, the first thing you need to do is to "pair" your phone with your laptop. Make sure the Bluetooth settings on your phone say that it is "discoverable." Go to System Preferences>Bluetooth, then ensure that the box besides "Discoverable" is checked (if not, click the box so that a checkmark appears). Then click the "+" at the bottom of the left box. A setup assistant will guide you through the remaining steps to pair your phone with your laptop.
I have a BlackBerry Pearl 8100. BlackBerry phone can only send files to Macs, they cannot sync with Macs via Bluetooth. I do not know how to export my phone book to my MacBook Pro, but when I send pictures, I select "send using bluetooth". It then asks which device to send the file to. My MacBook Pro then displays a message that my phone is sending a file and asks if I want to accept that file. I select yes, and the picture is downloaded into the documents stack. Of course, +this paragraph+ is only how my phone connects via Bluetooth to my MacBook Pro. If you have a phone from a different manufacturer, your steps will be different. I only provided this as an example.
Maybe you are looking for
-
Videos are choppy on new Macbook Pro 13''
Hello everyone, I just got a new Macbook Pro. I've downloaded the most recent versions of Quicktime and Flash but whenever I try to view a video, it takes a while to start playing and then once it does start it freezes about every 20 seconds. I've tr
-
Transient VO losing data on refresh
Hi - I am facing issue in retaining data in Transient VO. I have dropped a Transient VO on jspx as a table and on page load I am calling an AM method and inserting data in the VO. Initially, it works well and I can get the data on the page. But, when
-
How would i can select multiple photos in album in a shot?
I would like to select mutiple photos in my album in a shot, so that i can share my photostream.Is there any way to do that?If not, when can we expect this feature?I feel this is a must have feature
-
I'm getting an iPhone and I want to know what I am looking for in data usage and space? Let me know? Thanks
-
Victor, I find Tor's and Greg M's bpcatalog documents describing AJAX and JSF useful. However they do not address 'updates'. Updating the model via an AJAX request that is handled by the JSF framework as suggested by bccatalog examples is a challenge