Setup problem - using 8520 as modem

Hi,
I am following the instruction here to setup my device (unlucked Curve 8520, with AT&T)
http://www.blackberry.com/btsc/search.do?cmd=displayKC&docType=kc&externalId=KB05196
At task 2, step 7, I can not input any character in the Extra initialization commands field...
Can anyone give me some hind to proceed? Thank you so much!
Moreover, I followed another instruction and had another problem
http://www.blackberryforums.com/blackberry-guides/2019-user-howto-use-blackberry-modem-laptop.html
At step 8, I check my "Standard Modem Properties" - Diagnostics - Query Modem, and got something seemingly incorrect:
AT+FCLASS=? COMMAND NOT SUPPORTED
AT#CLS=?    COMMAND NOT SUPPORTED
AT+GCI?    COMMAND NOT SUPPORTED
AT+GCI=?   COMMAND NOT SUPPORTED
I feel the two issues are not dependent. Please help me resolve them. Thank you so much!
Sean

Which version of the Desktop Manager are you running? If you're running 5.0.1 can you try to use the IP Modem option to setup the modem?
If someone has been helpful please consider giving them kudos by clicking the star to the left of their post.
Remember to resolve your thread by clicking Accepted Solution.

Similar Messages

CSS 11501 ftp server setup problem using non-standard port

Dear Expert,
we would like to setup FTP server over CSS where our member sever use non-std-port to open both control/data channel (i.e. 6370 as ctrl and 6369 as data this case.) but seems we only get Passive mode FTP mode work only but not for Active mode FTP case for data channel establishement for server back to client...is there any professional advise can help on this case...? here is our setup info FYI
# sh ver
Version:               sg0820501 (08.20.5.01)
Flash (Locked):        08.10.1.06
Flash (Operational):   08.20.5.01
Type:                  PRIMARY
Licensed Cmd Set(s):   Standard Feature Set
                       Secure Management
CVDM Version:          cvdm-css-1.0_K9
!*************** Global
ftp data-channel-timeout 10
ftp non-standard-ports
!************************** SERVICE **************************
service ftp_ftpgtw
keepalive maxfailure 2
keepalive frequency 15
keepalive retryperiod 2
keepalive type tcp
ip address 192.168.52.170
protocol tcp
keepalive port 6370
port 6370
active
# sh run group drfusegtwftp_grp
!*************************** GROUP ***************************
group gtwftp_grp
vip address 192.168.52.28
add service ftp_ftpgtw
active
content ftp_gtwpkg-ftpgtw
    add service ftp_ftpgtw
    vip address 192.168.52.28
    port 21
    protocol tcp
    application ftp-control
    active

Thanks for your confirmation on no prob found in config level 1st..:P..as to save us a lot of time in isolating problem at this level.
What we can notice is seems the data port connection is fail to open for server back to client....for our general sense..... the flow expected should be:
TCP session A -- Client:1234 --> VIP:21 --> member svr:6370
TCP session B -- Client: 5678 <--> VIP:20 <--> member Svr: 6379 [on demand generated between server/client]
but we can only see session B fail to setup when client side access VIP site on CSS..even we try to put the most standard case as below
TCP session A -- Client:1234 --> VIP:21 --> member svr:21
TCP session B -- Client: 5678 <--> VIP:20 <--> member Svr: 20
we still unable to make the Active mode FTP access work either...hence we got no idea on how CSS handle FTP access when it involve services over multiple tcp ports..
and from CSS xlate view...the problem is we can only see what NAT IP that used in CSS connect to client...but no way to confirm for which port for VIP using outgoing to client. neither it is dropped by CSS..nor it is never setup from VIP to Client side.

Email setup problems curve 8520

I am in Ireland so not sure what help I can get but I have a Blackberry curve 8520, I recently had to get a new one as my first one kept freezing, so as expected I had to setup up my email etc again, the only email option I have is the enterprise one, I have gone to advanced options and sent the registration message and it says my handheld is registered with the wireless network but I only have 2 things in my service book and when I went into the shop I bought it in they said there should be more than 2 options, that was a week ago, and still no change, can someone please help

Hi and Welcome to the Community!
It sounds like your mobile service provider has not properly shifted your BIS account from your old BB to your new one. I recommend that you go see them again, but this time don't let them fob you off...you PAY them for 100% of your services and 100% of your support...right now they are delivering neither.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Problem using Apple External Modem in France

Hi,
My dad lives in France but purchased his MacBook and Apple External USB modem here in the US. He has been unable to get a reliable dialup connection with the Apple modem, though his older PC laptop routinely gets a solid connection. I know about the USB bug in 10.4.7 mentioned in several other discussions, but downloading and installing the "backgrade" fix did not solve the problem. He even purchased a second Apple modem from the French online Apple store but had the same problem.
Does anyone know if the Apple modem is designed to work in foreign countries, or does he need to buy a third-party modem manufactured in France? Any other suggestions?
Thanks!
MacBook Mac OS X (10.4.7)

I'm guessing here, but since all the issues with 10.4.7 have been addressed with 10.4.8, your dad should be fine right now. Tell him to upgrade. I seem to recall that this upgrade specifically states that French issues with the modem have been addressed and solved.

Problem on loading DAT file when using 3G network modem

Hello,
I'm having some strange problem when I'm trying to load my game on the part where DAT file with Map Object is read, using 3G Network Modem. This issue started when I migrated my applet from one host to another. Everything loads well, until the user authentication. On user authenticatiom I'm recieving map name which I should load and show the user on it. I'm recieving the message where map name is mentioned, but after, when the process of loading map begins(when I need to read DAT file which is only 15KB) application blocks(browser and JVM also block).
I thought it could be because of slow network communication, but it's not the reason, since I have tested(using Bandwidth limiter software) with 5 KBs/Second and it loads well and application is running well.
Any clue why this can happen? If code is needed I'll post some pieces related to the process of map creation.
URL or application: [ http://mimosa.dei.uc.pt/serhiy/demo/hoonline.html|http://mimosa.dei.uc.pt/serhiy/demo/hoonline.html]
Accounts: test01/test01 ... test0n/test0n ... test05/test05 (n is number from 1 to 5)
Thanks in advance!

You have to upload it with FileReference.upload() to a PHP
(or other server-side) script which saves it to a folder on the
server. When the DataEvent.UPLOAD_COMPLETE_DATA event has been
dispatched you can then use the FileReference.name to load from the
file on the server just like any other image.

Problem using new modem with TC

Hello all. I successfully set up a new AT&T DSL modem today which is working good when connected to my iMac. But when I connected it to the WAN on the TC things weren't working like before. Using AirPort Utility, I did a factory reset and while going through the setup routine, I got a message that I never saw with the old modem:
So I hit continue
Then update. After finishing and closing AirPort Utility, the iMac complained:
And of course I can't go online using TC. Any advice?

The message was right .. you should have put the TC in bridge mode.. you have smashed the setup by using double NAT and something is also using your address..
Shut down everything.. reboot in order.. modem.. TC.. computers. 2min gap for everything.
That should get rid of the IP conflict.. then do the setup again. This time follow the instruction to bridge the TC.

Hi, every time i try downloading ios5 it reaches 100% and then the connection times out and nothing happens after that; though the internet connection is fine as i can access other sites etc. what could be the problem?i tried using 2 different modems.

Hi, every time i try downloading ios5 it reaches 100% and then the connection times out and nothing happens after that; though the internet connection is fine as i can access other sites etc. what could be the problem?i tried using 2 different modems. Where can i download the ios5 from as my itunes is on my desktop which uses windows xp. Please help

Download iOS 5.1
iOS 5.1 (build 9B176) is compatible with iPad 1, iPad 2, iPhone 3GS, iPhone 4, iPhone 4S, iPod touch 3rd & 4th gen, and iPad 3. Additional builds are available for Apple TV 2 and Apple TV 3. The below download links are all direct downloads of iOS 5.1 from Apple.
iPad 1
iPad 2 Wi-Fi
iPad 2 GSM (AT&T)
iPad 2 CDMA (Verizon)
iPad 2,4
iPhone 3GS
iPhone 4 GSM (AT&T)
iPhone 4 CDMA (Verizon)
iPhone 4S
iPod touch 3G
iPod touch 4G
iPad 3 Wi-Fi
iPad 3 GSM
iPad 3 CDMA
Apple TV 2 (9B179b1)
Apple TV 3 (9B179b1)
Source: http://osxdaily.com/2012/03/07/ios-5-1-download/

Problems in using iPhone as modem

I have Iphone5 just updated to 6.1.2 and Macbook 10.7.5 with Itunes 11.02. I have used my Iphone as modem many years and I know how to use it.
Now after updating 6.1.2 I have lost Iphone-Usb in network connections and it is not possible to add it. There is only wifi, firewire, mbbethernet and ethernet.
In Iphone hotspot is of course in use and i renewed usb lightning cord. I habe tried the way to rename network**.plist files but with no results. Ihave updated 6.1.2 now three times. Ihave no problems when I use Macbook with huawei modem, and also my Iphone is working very well. So problem is only when I try to use it as modem to my Macbook. What I have to do now?

Yes. Now called Personal Hotspot.

Problem using Toshiba Software Installer for Win 7 on Satellite L750-1MT

Hello!
I have problem using Toshiba Software Installer for Win 7 on Satellite L750-1MT (PSK30E-02T002B3) with no OS preinstalled.
I do the following:
1. Install Windows 7 x64, SP1.
2. Install LAN driver (device was not recognized by Windows 6) (downloaded from [http://se.computers.toshiba-europe.com/innovation/jsp/supportMyProduct.do?service=SE&LNG=26&userAction=S MP_RESULTS_PAGE&partNumber=PSK30E-02T002B3&serialNumber=&USER_ACTION=Serial%20number])
3. Install all Windows Updates from Microsoft
4. Run Toshiba Software Installer for Win 7 - it installs a couple of drivers and then asks to reboot.
Here is the log file for the first try (win7update.log):
Update started 12\28\2011 at 21:11
Installed TVALZ_O.INF
Installed IO & Memory Access Driver
driver_bluetooth_TC00241200A.exe /s /log /test has been installed with the result code of PASS
util_tvap_TC00215000H.exe /s /log /test /wait15 has been installed with the result code of PASS
Update completed at 21:29
After reboot I run it again and the result is:
Update started 12\28\2011 at 21:38
Toshiba Bluetooth stack has already been installed.
Toshiba Value Added Package has already been installed.
Update completed at 21:40
Any help is appreciated!
Thanks in advance!

You are right this notebook model was delivered without OS.
Win7 64bit is supported for this notebook model and all necessary drivers, tools and utilities are available on Toshiba download page.
What I can say is that all this stuff must be installed in right install order. I know it sounds stupid now but I recommend you to make clean OS again and continue installation following this installation order:
Win7 SP1
Intel Chipset SW Installation Utility 9.2.0.1015
TOSHIBA Supervisor Password Utility 4.8.6.0
TOSHIBA HW Setup Utility 4.8.6.0
TOSHIBA Bulletin Board V2.1.10
TOSHIBA ReelTime 1.7.17.0
Intel Management Engine Interface 7.0.2.1164
NVIDIA Display Driver 8.17.12.6669
Intel Rapid Storage Technology Driver 10.1.2.1004
TOSHIBA Value Added Package 1.5.4.64
USB3.0 Driver 2.0.32.0
NVIDIA HD Audio Driver 1.1.13.1
Conexant Audio Driver 8.51.1.0a
Intel Wireless LAN Driver 14.0.2.2.1.s64_wCAT
or
Atheros Wireless LAN Driver 9.2.0.206.0.s3264_wCAT
or
Realtek Wireless LAN Driver 2.00.0013
TOSHIBA Wireless LAN Indicator 1.0.3
Synaptics Touch Pad Driver 15.2.11.1
TOSHIBA Software Modem 2.2.97(SM2297ALS05)
Conexant Modem Driver 7.80.4.53
TOSHIBA HDD Protection 2.2.1.12
Atheros Bluetooth Filter Driver Package v1.0.7
Bluetooth Stack for Windows by Toshiba v8.00.04(T)
Atheros LAN Driver 1.0.0.46
Realtek Card Reader 1.0.0.12
TOSHIBA Sleep Utility 1.4.2.7
TOSHIBA Face Recognition V3.1.8
TOSHIBA eco Utility 1.2.25.64
Intel Proset 14.0.2.0.1.s64_wCAT
Intel Wireless Display 2.0.29T
TOSHIBA HDD_SSD Alert 3.1.64.7
TOSHIBA Service Station V2.1.52
TOSHIBA PC Health Monitor 1.7.4.64
ConfigFree 8.0.37
TOSHIBA Web Camera Application V2.0.0.19
TOSHIBA Network Device ID Registry Setting Tool 3.0.32.4-14_wMSI
TOSHIBA Media Controller 1.0.86.2
TOSHIBA Media Controller Plug-in 1.0.6.1
PatchFiles$$2 PCIIDEREG-1.2
PatchFiles$$3 TosVolRegulator_x64_1.1
It is very important to use right installation order.
Please post some feedback.

Verizon DSL and Airport Extreme Setup Problem

I have Verizon DSL (not FIOS). I am using a Westell modem, model number B90-210015-04.
I try to go through the setup but the Airport Extreme Utility says it cannot find a valid IP address (the light keeps flashing).
I have it setup in bridge mode since I think my modem is also a router. However, there are a lot of other inputs in the setup and I don't know if I need to put in anything for those (e.g. DNS Servers, Domain Name, etc.). I called Verizon and they said there shouldn't be any special inputs. They implied it should just work out of the box.
The modem is working with my existing Netgear router (model number WGR614 v4).
Any help?

Had the same problem. Had the same setup as yours.
If you use WPA/WPA2 and if your password is too short (less than or equal to 8 characters), the AirPort Extreme Utility will misleadingly tell you it cannot find a valid IP address. As it turns out, WPA/WPA2 requires a longer password (see http://en.wikipedia.org/wiki/Wpa2). I don't understand why a weak password would result in a confusing error message like this, but after I used a stronger and longer password, the dreadful amber light finally turned green!
PS: I didn't enter any DNS/DHCP info nor my DSL account/password info throughout the entire setup process. I figured that if I didn't need these pieces of information with the old router before then I shouldn't need them with this new hardware.

Problem using Time Capsule as Router

I just purchased an Airport Time.Capsule.802.11AC 2TB router for my home, which for the last year worked happily with a an inexpensive router. My home system is reasonably complex, with a guest house with an Airport Express used as an wireless access point, and and Airport used in another part of the house. Both the Express and Airport extend the network (and have done so in the past).
Since installing the Time Capsule 2 days ago, I have had no end of problems, first with getting devices to connect wirelessly; I seem to have (generally) solved this problem by deleting the old wireless details and entering the new wireless access details (even though the access point name and password remains the same).
Still, problems plague me. The Airport seems to intermittently report that it cannot extend the network; internet access speeds are sometimes slow or non existent (last night, download speed was 2MB/S, upload speeds noon existent). I suspect this must be because of some conflict within my system: I use a cable modem, and right now all wireless clients gain access via DHCP.
I've attached my 'settings' for the router.
Is there a setting which is obviously out of place, or some other idea as to how to debug? I wonder if the router is using a new wireless protocol what older iPads/laptops/etc cannot speak to as quickly, but dismissed that as somewhat illogical.

How can I determine if it is a firmware fault?
Because you test precisely for where the fault is..
To do that you measure local lan speeds, connectivity and reliability using ethernet and wireless.
And then do the same with WAN.. you will discover where the problem exists.. if it is wan speed or drop out then you can be very sure it is WAN bugs.
This is as I stated an issue with the AC model.. and all the firmware seem to be affected but you should be on 7.7.3 as the earlier ones are not secure.
Why would Apple ever release such a device with a known fault?
The following is pure speculation .. and might get deleted.. !!
Why did apple release a bad update for iphone 6?? Lack of testing.
http://bgr.com/2014/09/25/iphone-6-and-iphone-6-plus-ios-8-0-2-release/
Why do they produce phones that bend? Lack of testing.
http://www.macrumors.com/2014/09/25/apple-responds-to-bending-issues/
This is more typical apple response .. ie in normal usage they are fine. ie it is end users that are at fault. Should not wear tight pants.
In networking there are huge numbers of products in the marketplace. To get reasonable products to market you need to test vigorously and update continually until you find all the bugs.. Since Apple released the AC model there has been two firmware updates.. one on the day of release.. and one recently with the ssh bug.. (one other was withdrawn after a few days.. as typical it caused more problems than it fixed.. which is lack of testing). For a new leading edge product this is totally inadequate. But I am sure it worked fine on the two different cable modems they tested it on.. and 3 different dsl modems and 2 different fibre setups.. unfortunately there are thousands upon thousands of modems and routers out there. A large beta program is required.. but Apple could not do that as it would be releasing hardware without marketing fanfare.
I personally have these issues with the Airport Extreme and Time Capsule on my ADSL.. it simply does not work reliably. No other router I have tested fails. I have tested lots.. but the Apple cannot maintain a pppoe connection to ISP equipment. All other routers can. For some it works perfectly.. for some it doesn't work at all.. for me it drops out at 2min intervals. It is simply unsuited to the task. Find another way to use it .. or return it. Clearly they don't get enough returns to believe the issue is that big.
In the forum we deal with it every day.. eg today.
ISP Speed issue after installing TC
Just do a search for SB6121 or SB6141 which seem particularly prone to the problem.

Using a Bluetooth modem and mouse together?

After much messing around I'm now able to use my T-Mobile Motorola W-490 as a Bluetooth modem with my 500MHz dual USB G3 iBook through a Bluetooth USB dongle. I'm using it to post this message actually. For some reason it won't work without Bluetooth, using just a USB cable to connect the computer to the phone. I guess I can live with that.
My question is, why can't I use any other Bluetooth device, including an Apple wireless mouse, or even the flash drive inside the W-490, while the modem is connected? Is this normal? When the phone isn't being used as a modem I can use its internal flash drive and a Bluetooth mouse together at the same time. My Bluetooth dongle is Bluetooth 2.0 even though the other devices are Bluetooth 1.0 I think (?) I'm new to Bluetooth, so any help would be appreciated.

You need a Bluetooth dongle or built in Bluetooth. I couldn't get it to connect through a USB cable.
Call T-Mobile and subscribe to their additional $20/month internet plan.
Wait a couple of days for T-Mobile to turn on the internet on your phone.
Download and install the "Motorola 3G CID1" modem script so Mac OS-X will recognize the phone as a modem.
Make the phone discoverable to other Bluetooth devices.
Setup the Bluetooth device with Bluetooth Setup Assistant.
Setup a new modem in Network preferences.
Show the new modem, and under the PPP tab set it to dial telephone number: "internet2.voicestream.com"
Under Bluetooth Modem select modem: "Motorola 3G CID1"
I'm sure I'm forgetting something. Write back if you have problems and maybe I'll remember more. You can call T-Mobile and ask for their Mac technical person. I shut off T-Mobile's internet service because it wasn't worth the extra $20/month to me. It's faster than a dialup modem when used as a modem to allow a computer to access the internet. The W490 phone used by itself to access the internet is unbelievably, mind numbingly slooow. (pulling hair) I'll probably have T-Mobile turn the internet back on when I go visit my mom, who doesn't have any internet connection at all. I'll shut it off as soon as I get back though. It'll make a nice way to get e-mail without driving down to a cafe with wireless. If you travel a lot this might be an affordable way to get your e-mail. It's much more affordable than a dedicated 3G modem, but it's also much slower.

I am trying to setup wireless using my old dome Airport ExtremeBase station. I had previously used it about 5 years ago when I had dial up but have now switche to DSL with Windstream. I can not get connecte as ABS keeps trying to dial up(the phone number)

I am trying to setup wireless using my old dome Airport Extreme Base station. I had previously used it about 5 years ago when I had dial up but have now switched to DSL with Windstream. I can not get connected as the ABS keeps trying to dial up(the old phone number). When I tried to change my network settings an annoying popup window says "your network settings have been changed by another application'. I have no idea what the message is all about and when I close this window it immediately pops up again and prevents me -as far as I can tell -from changing my Airport settings? I need advice on how to get this wireless setup done. Maybe a reset? or something else? I have the DSL phone line plugged into WIndsteam Seimens Speedstream 4200 modem and then the ethernet (yellow) wire from the WIndsteam Seimens Speedstream 4200 modem to the port on the dome that is a circle of dots.

1)Can you explain how using the AEBS as a bridge will work with the Seimens Speedstream4200?
As a bridge, the AEBS will basically become a wireless access point. This will allow the AEBS to provide a wireless network, but still allow the Speedstream to provide NAT & DHCP services for the wireless clients connected to the AEBS. If the AEBS was left as a router, you would have a double-NAT condition which isn't necessary bad in itself, but would create a second subnet. That would make it more difficult for clients connected to the AEBS to access clients connected to the Speedstream.
2) Is there a link that will guide me through the steps to set the AEBS as a bridge?
You can easily reconfigure the AEBS as a bridge using the AirPort Utility.
ref: AirPort Utility > Select the AEBS > Manual Setup > Internet > Internet Connection > Connection Sharing = Off (Bridge Mode)
3)Can I just connect the DSL phone line to the AEBS and eliminate the Speedstream4200?
Unfortunately no. The AEBS does not have a built-in DSL modem. You will still need the Speedstream to provide this function.

Problem using integrated WLS in jDeveloper 11.1.2.1.0

Hey there,
I got a problem using the integrated WLS from the jDeveloper 11.1.2.1.0.
After trying to deploy an ADF Web Application on the integrated WLS, I get the following log message:
LOG
+[Waiting for the domain to finish building...]+
+[11:26:04 AM] Creating Integrated Weblogic domain...+
+[11:28:13 AM] Extending Integrated Weblogic domain...+
+[11:30:06 AM] Integrated Weblogic domain processing completed successfully.+
*** Using HTTP port 7101 ***
*** Using SSL port 7102 ***
+/home/robin/.jdeveloper/system11.1.2.1.38.60.81/DefaultDomain/bin/startWebLogic.sh+
+[waiting for the server to complete its initialization...]+
+.+
+.+
JAVA Memory arguments: -Xms256m -Xmx512m -XX:CompileThreshold=8000 -XX:PermSize=128m -XX:MaxPermSize=512m
+.+
WLS Start Mode=Development
+.+
CLASSPATH=/home/robin/bin/wls/oracle_common/modules/oracle.jdbc_11.1.1/ojdbc6dms.jar:/home/robin/bin/wls/patch_wls1211/profiles/default/sys_manifest_classpath/weblogic_patch.jar:/home/robin/bin/wls/patch_oepe100/profiles/default/sys_manifest_classpath/weblogic_patch.jar:/home/robin/bin/wls/patch_ocp371/profiles/default/sys_manifest_classpath/weblogic_patch.jar:/home/robin/bin/wls/jdk160_29/lib/tools.jar:/home/robin/bin/wls/wlserver_12.1/server/lib/weblogic_sp.jar:/home/robin/bin/wls/wlserver_12.1/server/lib/weblogic.jar:/home/robin/bin/wls/modules/features/weblogic.server.modules_12.1.1.0.jar:/home/robin/bin/wls/wlserver_12.1/server/lib/webservices.jar:/home/robin/bin/wls/modules/org.apache.ant_1.7.1/lib/ant-all.jar:/home/robin/bin/wls/modules/net.sf.antcontrib_1.1.0.0_1-0b2/lib/ant-contrib.jar:/home/robin/bin/wls/oracle_common/modules/oracle.jrf_11.1.1/jrf.jar:/home/robin/bin/wls/wlserver_12.1/common/derby/lib/derbyclient.jar:/home/robin/bin/wls/wlserver_12.1/server/lib/xqrl.jar
+.+
PATH=/home/robin/bin/wls/wlserver_12.1/server/bin:/home/robin/bin/wls/modules/org.apache.ant_1.7.1/bin:/home/robin/bin/wls/jdk160_29/jre/bin:/home/robin/bin/wls/jdk160_29/bin:/usr/local/bin:/usr/bin:/bin:/opt/bin:/usr/x86_64-pc-linux-gnu/gcc-bin/4.5.3:/usr/games/bin
+.+
+* To start WebLogic Server, use a username and   *+
+* password assigned to an admin-level user. For *+
+* server administration, use the WebLogic Server *+
+* console at http://hostname:port/console        *+
starting weblogic with Java version:
java version "1.6.0_29"
Java(TM) SE Runtime Environment (build 1.6.0_29-b11)
Java HotSpot(TM) Client VM (build 20.4-b02, mixed mode)
Starting WLS with line:
+/home/robin/bin/wls/jdk160_29/bin/java -client -Xms256m -Xmx512m -XX:CompileThreshold=8000 -XX:PermSize=128m -XX:MaxPermSize=512m -Dweblogic.Name=DefaultServer -Djava.security.policy=/home/robin/bin/wls/wlserver_12.1/server/lib/weblogic.policy -Djavax.net.ssl.trustStore=/tmp/trustStore7618453572230021232.jks -Dhttp.proxyHost=emea-proxy.uk.oracle.com -Dhttp.proxyPort=80 -Dhttp.nonProxyHosts=localhost|localhost.localdomain|127.0.0.1|::1|MUELLER-BADY-GENTOO|MUELLER-BADY-GENTOO -Dhttps.proxyHost=emea-proxy.uk.oracle.com -Dhttps.proxyPort=80 -Doracle.jdeveloper.adrs=true -Dweblogic.nodemanager.ServiceEnabled=true -Xverify:none -Djava.endorsed.dirs=/home/robin/bin/wls/jdk160_29/jre/lib/endorsed:/home/robin/bin/wls/wlserver_12.1/endorsed -da -Dplatform.home=/home/robin/bin/wls/wlserver_12.1 -Dwls.home=/home/robin/bin/wls/wlserver_12.1/server -Dweblogic.home=/home/robin/bin/wls/wlserver_12.1/server -Djps.app.credential.overwrite.allowed=true -Dcommon.components.home=/home/robin/bin/wls/oracle_common -Djrf.version=11.1.1 -Dorg.apache.commons.logging.Log=org.apache.commons.logging.impl.Jdk14Logger -Ddomain.home=/home/robin/.jdeveloper/system11.1.2.1.38.60.81/DefaultDomain -Djrockit.optfile=/home/robin/bin/wls/oracle_common/modules/oracle.jrf_11.1.1/jrocket_optfile.txt -Doracle.server.config.dir=/home/robin/.jdeveloper/system11.1.2.1.38.60.81/DefaultDomain/config/fmwconfig/servers/DefaultServer -Doracle.domain.config.dir=/home/robin/.jdeveloper/system11.1.2.1.38.60.81/DefaultDomain/config/fmwconfig -Digf.arisidbeans.carmlloc=/home/robin/.jdeveloper/system11.1.2.1.38.60.81/DefaultDomain/config/fmwconfig/carml -Digf.arisidstack.home=/home/robin/.jdeveloper/system11.1.2.1.38.60.81/DefaultDomain/config/fmwconfig/arisidprovider -Doracle.security.jps.config=/home/robin/.jdeveloper/system11.1.2.1.38.60.81/DefaultDomain/config/fmwconfig/jps-config.xml -Doracle.deployed.app.dir=/home/robin/.jdeveloper/system11.1.2.1.38.60.81/DefaultDomain/servers/DefaultServer/tmp/_WL_user -Doracle.deployed.app.ext=/- -Dweblogic.alternateTypesDirectory=/home/robin/bin/wls/oracle_common/modules/oracle.ossoiap_11.1.1,/home/robin/bin/wls/oracle_common/modules/oracle.oamprovider_11.1.1 -Djava.protocol.handler.pkgs=oracle.mds.net.protocol -Dweblogic.jdbc.remoteEnabled=false -Dwsm.repository.path=/home/robin/.jdeveloper/system11.1.2.1.38.60.81/DefaultDomain/oracle/store/gmds -Dweblogic.management.discover=true -Dwlw.iterativeDev= -Dwlw.testConsole= -Dwlw.logErrorsToConsole= -Dweblogic.ext.dirs=/home/robin/bin/wls/patch_wls1211/profiles/default/sysext_manifest_classpath:/home/robin/bin/wls/patch_oepe100/profiles/default/sysext_manifest_classpath:/home/robin/bin/wls/patch_ocp371/profiles/default/sysext_manifest_classpath weblogic.Server+
+<Feb 10, 2012 11:30:09 AM CET> <Info> <Security> <BEA-090905> <Disabling CryptoJ JCE Provider self-integrity check for better startup performance. To enable this check, specify -Dweblogic.security.allowCryptoJDefaultJCEVerification=true>+
+<Feb 10, 2012 11:30:10 AM CET> <Info> <Security> <BEA-090906> <Changing the default Random Number Generator in RSA CryptoJ from ECDRBG to FIPS186PRNG. To disable this change, specify -Dweblogic.security.allowCryptoJDefaultPRNG=true>+
+<Feb 10, 2012 11:30:11 AM CET> <Info> <WebLogicServer> <BEA-000377> <Starting WebLogic Server with Java HotSpot(TM) Client VM Version 20.4-b02 from Sun Microsystems Inc..>+
+<Feb 10, 2012 11:30:12 AM CET> <Info> <Management> <BEA-141107> <Version: WebLogic Server 12.1.1.0 Wed Dec 7 08:40:57 PST 2011 1445491 >+
+<Feb 10, 2012 11:30:15 AM CET> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to STARTING.>+
+<Feb 10, 2012 11:30:15 AM CET> <Info> <WorkManager> <BEA-002900> <Initializing self-tuning thread pool.>+
+<Feb 10, 2012 11:30:15 AM CET> <Notice> <Log Management> <BEA-170019> <The server log file /home/robin/.jdeveloper/system11.1.2.1.38.60.81/DefaultDomain/servers/DefaultServer/logs/DefaultServer.log is opened. All server side log events will be written to this file.>+
Feb 10, 2012 11:30:24 AM oracle.security.jps.internal.keystore.file.FileKeyStoreManager saveKeyStore
WARNING: Failed to save farm keystore. Reason {0}
Feb 10, 2012 11:30:24 AM oracle.security.jps.internal.keystore.file.FileKeyStoreManager createKeyStore
WARNING: Failed to save farm keystore. Reason {0}
oracle.security.jps.service.keystore.KeyStoreServiceException: JPS-06513: Failed to save farm keystore. Reason
+     at oracle.security.jps.internal.keystore.file.FileKeyStoreManager.createKeyStore(FileKeyStoreManager.java:309)+
+     at oracle.security.jps.internal.keystore.file.FileKeyStoreServiceImpl.doInit(FileKeyStoreServiceImpl.java:95)+
+     at oracle.security.jps.internal.keystore.file.FileKeyStoreServiceImpl.<init>(FileKeyStoreServiceImpl.java:73)+
+     at oracle.security.jps.internal.keystore.file.FileKeyStoreServiceImpl.<init>(FileKeyStoreServiceImpl.java:63)+
+     at oracle.security.jps.internal.keystore.KeyStoreProvider.getInstance(KeyStoreProvider.java:157)+
+     at oracle.security.jps.internal.keystore.KeyStoreProvider.getInstance(KeyStoreProvider.java:64)+
+     at oracle.security.jps.internal.core.runtime.ContextFactoryImpl.findServiceInstance(ContextFactoryImpl.java:139)+
+     at oracle.security.jps.internal.core.runtime.ContextFactoryImpl.getContext(ContextFactoryImpl.java:170)+
+     at oracle.security.jps.internal.core.runtime.ContextFactoryImpl.getContext(ContextFactoryImpl.java:191)+
+     at oracle.security.jps.internal.core.runtime.JpsContextFactoryImpl.getContext(JpsContextFactoryImpl.java:132)+
+     at oracle.security.jps.internal.core.runtime.JpsContextFactoryImpl.getContext(JpsContextFactoryImpl.java:127)+
+     at oracle.security.jps.internal.policystore.PolicyUtil$1.run(PolicyUtil.java:850)+
+     at oracle.security.jps.internal.policystore.PolicyUtil$1.run(PolicyUtil.java:844)+
+     at java.security.AccessController.doPrivileged(Native Method)+
+     at oracle.security.jps.internal.policystore.PolicyUtil.getDefaultPolicyStore(PolicyUtil.java:844)+
+     at oracle.security.jps.internal.policystore.PolicyDelegationController.<init>(PolicyDelegationController.java:291)+
+     at oracle.security.jps.internal.policystore.PolicyDelegationController.<init>(PolicyDelegationController.java:284)+
+     at oracle.security.jps.internal.policystore.JavaPolicyProvider.<init>(JavaPolicyProvider.java:270)+
+     at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)+
+     at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39)+
+     at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27)+
+     at java.lang.reflect.Constructor.newInstance(Constructor.java:513)+
+     at java.lang.Class.newInstance0(Class.java:355)+
+     at java.lang.Class.newInstance(Class.java:308)+
+     at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.loadOPSSPolicy(CommonSecurityServiceManagerDelegateImpl.java:1343)+
+     at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.initialize(CommonSecurityServiceManagerDelegateImpl.java:1022)+
+     at weblogic.security.service.SecurityServiceManager.initialize(SecurityServiceManager.java:873)+
+     at weblogic.security.SecurityService.start(SecurityService.java:148)+
+     at weblogic.t3.srvr.SubsystemRequest.run(SubsystemRequest.java:64)+
+     at weblogic.work.ExecuteThread.execute(ExecuteThread.java:256)+
+     at weblogic.work.ExecuteThread.run(ExecuteThread.java:221)+
+<Feb 10, 2012 11:30:24 AM CET> <Error> <Security> <BEA-090892> <The loading of OPSS java security policy provider failed due to exception, see the exception stack trace or the server log file for root cause. If still see no obvious cause, enable the debug flag -Djava.security.debug=jpspolicy to get more information. Error message: oracle.security.jps.JpsException: [PolicyUtil] Exception while getting default policy Provider>+
+<Feb 10, 2012 11:30:24 AM CET> <Critical> <WebLogicServer> <BEA-000386> <Server subsystem failed. Reason: weblogic.security.SecurityInitializationException: The loading of OPSS java security policy provider failed due to exception, see the exception stack trace or the server log file for root cause. If still see no obvious cause, enable the debug flag -Djava.security.debug=jpspolicy to get more information. Error message: oracle.security.jps.JpsException: [PolicyUtil] Exception while getting default policy Provider+
+weblogic.security.SecurityInitializationException: The loading of OPSS java security policy provider failed due to exception, see the exception stack trace or the server log file for root cause. If still see no obvious cause, enable the debug flag -Djava.security.debug=jpspolicy to get more information. Error message: oracle.security.jps.JpsException: [PolicyUtil] Exception while getting default policy Provider+
+     at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.loadOPSSPolicy(CommonSecurityServiceManagerDelegateImpl.java:1402)+
+     at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.initialize(CommonSecurityServiceManagerDelegateImpl.java:1022)+
+     at weblogic.security.service.SecurityServiceManager.initialize(SecurityServiceManager.java:873)+
+     at weblogic.security.SecurityService.start(SecurityService.java:148)+
+     at weblogic.t3.srvr.SubsystemRequest.run(SubsystemRequest.java:64)+
+     Truncated. see log file for complete stacktrace+
+Caused By: oracle.security.jps.JpsRuntimeException: oracle.security.jps.JpsException: [PolicyUtil] Exception while getting default policy Provider+
+     at oracle.security.jps.internal.policystore.PolicyDelegationController.<init>(PolicyDelegationController.java:293)+
+     at oracle.security.jps.internal.policystore.PolicyDelegationController.<init>(PolicyDelegationController.java:284)+
+     at oracle.security.jps.internal.policystore.JavaPolicyProvider.<init>(JavaPolicyProvider.java:270)+
+     at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)+
+     at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39)+
+     Truncated. see log file for complete stacktrace+
+Caused By: oracle.security.jps.JpsException: [PolicyUtil] Exception while getting default policy Provider+
+     at oracle.security.jps.internal.policystore.PolicyUtil.getDefaultPolicyStore(PolicyUtil.java:899)+
+     at oracle.security.jps.internal.policystore.PolicyDelegationController.<init>(PolicyDelegationController.java:291)+
+     at oracle.security.jps.internal.policystore.PolicyDelegationController.<init>(PolicyDelegationController.java:284)+
+     at oracle.security.jps.internal.policystore.JavaPolicyProvider.<init>(JavaPolicyProvider.java:270)+
+     at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)+
+     Truncated. see log file for complete stacktrace+
+Caused By: java.security.PrivilegedActionException: oracle.security.jps.JpsException: [PolicyUtil] Unable to obtain default JPS Context!+
+     at java.security.AccessController.doPrivileged(Native Method)+
+     at oracle.security.jps.internal.policystore.PolicyUtil.getDefaultPolicyStore(PolicyUtil.java:844)+
+     at oracle.security.jps.internal.policystore.PolicyDelegationController.<init>(PolicyDelegationController.java:291)+
+     at oracle.security.jps.internal.policystore.PolicyDelegationController.<init>(PolicyDelegationController.java:284)+
+     at oracle.security.jps.internal.policystore.JavaPolicyProvider.<init>(JavaPolicyProvider.java:270)+
+     Truncated. see log file for complete stacktrace+
+Caused By: oracle.security.jps.JpsException: [PolicyUtil] Unable to obtain default JPS Context!+
+     at oracle.security.jps.internal.policystore.PolicyUtil$1.run(PolicyUtil.java:860)+
+     at oracle.security.jps.internal.policystore.PolicyUtil$1.run(PolicyUtil.java:844)+
+     at java.security.AccessController.doPrivileged(Native Method)+
+     at oracle.security.jps.internal.policystore.PolicyUtil.getDefaultPolicyStore(PolicyUtil.java:844)+
+     at oracle.security.jps.internal.policystore.PolicyDelegationController.<init>(PolicyDelegationController.java:291)+
+     Truncated. see log file for complete stacktrace+
Caused By: oracle.security.jps.service.keystore.KeyStoreServiceException: JPS-06513: Failed to save farm keystore. Reason
+     at oracle.security.jps.internal.keystore.file.FileKeyStoreManager.createKeyStore(FileKeyStoreManager.java:309)+
+     at oracle.security.jps.internal.keystore.file.FileKeyStoreServiceImpl.doInit(FileKeyStoreServiceImpl.java:95)+
+     at oracle.security.jps.internal.keystore.file.FileKeyStoreServiceImpl.<init>(FileKeyStoreServiceImpl.java:73)+
+     at oracle.security.jps.internal.keystore.file.FileKeyStoreServiceImpl.<init>(FileKeyStoreServiceImpl.java:63)+
+     at oracle.security.jps.internal.keystore.KeyStoreProvider.getInstance(KeyStoreProvider.java:157)+
+     Truncated. see log file for complete stacktrace+
+>+
+<Feb 10, 2012 11:30:24 AM CET> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to FAILED.>+
+<Feb 10, 2012 11:30:24 AM CET> <Error> <WebLogicServer> <BEA-000383> <A critical service failed. The server will shut itself down.>+
+<Feb 10, 2012 11:30:24 AM CET> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to FORCE_SHUTTING_DOWN.>+
Process exited.
*/LOG*
After that, I tried setting permissions for the cwallet.sso file to ugo+rwx, but this leads to the same problems as mentioned above.
My second try was to setup an external WLS 12c, but it seems to be not yet possible to connect to a WLS 12c from within jDeveloper.
Do you have any ideas ?
Thank you in advance for your help.
Regards,
Robin

After debugging the WLS Initialisation with jdb, I recognized that there was some trouble with dependent libraries.
In the end, I solved my problem by using another OS (Ubuntu 11.10) for development. There, the WLS works out of the box, even with 64-Bit libraries.
Thank you for your help.
Regards,
Robin

Could not complete the command because of a problem using the Adobe Color Engine

Hi all
This bizarrely started this morning - completely out of the blue - and I've no idea why.
Setup: Mac 10.8.2 / Creative Suite Premium PhotoShop CS5 extended (patched to 12.04)
Am working on images exported from LightRoom 4 (16bit A3 Pro Photo RGB PSDs) in PhotoShop CS5.
As part of my image grading process I have a PhotoShop Action that does the following: copy layer to new document (document respects all of copied layer settings) > Image > Adjustments > HDR toning > apply a certain HDR preset > copy to resultant image back to original doc > set opacity as 40%.
Totally out of the blue, after having this action for about 2 months, this morning I start getting a warning dialog of "Could not complete the command because of a problem using the Adobe Color Engine" and the action fails. The failure seems to take place at the 'make document' part of the action and seems to somehow be related to the contents of the clipboard.
I've tried trashing and re-creating the action. It works first time out fine and then - on the next image - errors again.
At present I can only safely carry out the work 'manually' by completing all the actions myself.
I can think of no settings that have changed and the OS hasn't been updated in a while.
I have found one other thread on a similar problem in PhotoShop Elements, but no definitive solution.
Any help appreciated as I have a shedload of stuff to process.
Best wishes
TP

OK: trash of prefs didn't work. Tried thrice. Re-created orig action. same problem.
BUT!
Your 'Image > Duplicate' suggestion does seem to work. If I use that in a new action as the method for creating the HDR version doc (instead of 'Select > Copy > New > Paste), it seems to work.
Will try that out this afternoon, but for now: WIN!
Many thanks for the suggestion!
TP

Setup problem - using 8520 as modem

Similar Messages

Maybe you are looking for