Setup vlan on solaris

i have 3 servers which are run on windows server 2003 and solaris 10...So, i need to setup vlan in each server. Our network will used ipv6 and ipv4 protocols..
The problem is i really dunno how to setup the network and interconnect between ipv4 and ipv6..The setup for vlan must done in server that run on solaris....tq for helping

Thanks for the update, We would love to have such a feature will greatly help in traffic isolation while still on the same vlan.

Similar Messages

Setup VLAN

Hello,
I want to setup VLAN to separate attached devices (will use a VLAN capabel WLAN accesspoint).
I am looking at the Cisco Small business products.
Like this: SG200-08P
This is my goal:
3 VLAN's: Internal, External, Guest
Devices connected to Internal can access External + Internet.
Devices connected to External can only access its own VLAN + Internet.
Devices connected to Guest are separated, they can only acess Internet.
I have a LAN Internet connection, with one IP address.
So I need NAT and Routing.
Do I need a VLAN enabled Router, or only a VLAN enabled Switch (Layer 2 / 3 / Smart)?
Can a Smart Switch act as Router?
Please advice me for Cisco - Products.

Hello Sam,
For your setup you will still want to get a router. Our Layer 3 switches do not do NATing or have any kind of firewall, so you probably would want something else in front of this on the edge of your network.
With a layer 3 switch it is possible to buy a router that doesn't do VLANs and still make it work. The RV series of routers would work well for this. All of them except for the RV016, RV042, and RV082 are VLAN capable. Even with those three you could set it up, it would just be a slightly different setup.
With a VLAN capable router you can do what is called router-on-a-stick, where all the VLANs are trunked up to the router, and it handles the Inter-VLAN routing. You can also set it up where the switch is everyone's default gateway, and it does the routing. In that case you would just have a point to point link between the router and switch, along with some static routes to make it all work.
So basically with a layer 3 switch you have some options, but you will still want a router for the NAT and the firewall features. It is possible to put a layer 3 switch directly on the edge, but only if you own enough public IPs for all of your devices.
Hope that helps a bit,
Christopher Ebert
Senior Network Support Engineer - Cisco Small Business Support Center

Setup Cluster using Solaris Container data service

We have a two-node cluster that we would like to use to create either a zone cluster or use the Solaris Container data service that would create a scalable (or multiple master) data service of two zones, one on each node. We have an app running in the zone, CiscoWorks, that has a local database of jobs that are scheduled to run to configure Cisco switches. I was curious how we setup the storage. If each zone is running on local disks, how do the zones stay in sync and the database updated with job information? Would I setup a device group of the disks where the zones will reside on each node? Can I use SAN as the local disk so the zones can be replicated to a Disaster Recovery location?
Thanks for any help,
Chuck

Chuck,
Sadly, I think I'm going to make your implementation decisions a lot more complicated because there are three ways you can use zones within Solaris Cluster.
1. Create a failover zone using the HA Solaris Container Data Service. Here the zone root moves between the cluster nodes as the zone fails over.
2. Create static zones between with resource groups can migrate. Each zone root is local the the physical node. However, the configuration of the zones can be subtly different.
3. Create a virtual cluster using static zones within which resource groups can migrate. Each zone root is local the the physical node. However, the configuration of the zones are forced to be the same.
Note also, that a ZFS zpool can only be mounted on one node or zone at anyone time, although it can be mounted read/write in one zone and read-only in other zones on the same node (IIRC).
I would be inclined to put your database into an HA configuration, i.e. one that runs on one node at any one time. I would then constrain that in a zone cluster that is bound to a project with restricted resources, i.e. CPUs and memory. Any other tiers of the application, could then be placed either in the global zone (main cluster) or placed in another zone cluster and equally constrained.
I don't know if that's any help. I can recommend a good book on the subject <shameless plug "Oracle Solaris Cluster Essentials"/>. The example chapters should be of help.
Regards,
Tim
---

Setup JDBC in Solaris

Hi there,
How could I setup a JDBC drivers for Java between my web server (Sun Solaris 8) and database server (Sun Solaris 2.5.1) and Oracle (7.3.4)?
Kindly show me some Java codes on the connection part...plz
Thanks
Neo

I think i found the solution, there is a CD to run with...

Need help - setup network in solaris

Hello! Today I install Solaris 10 for learning in my laptop and have some trouble. Please help me
1. Set up network interface for wi-fi card iwi0
(a. ifconfig iwi0 plumb
b. wificonfig iwi0 connect airJet
c. ifconfig iwi0 dhcp)
2. Set up default route (route add default 192.168.100.2 (its my access point with dhcp server))
Ping -s 192.168.100.2 -> done
But when I trying in Firefox open any url - recieve error "host not found"
okay. in terminal i put
ping google.com
and recieve answer
host not found
What is my problem?
Thanks for u answers.

Try changing hosts line in /etc/nsswitch.conf to:
hosts dns files
so that hostnames will be resolved via your dns servers. You also need to enter dns server info in /etc/resolv.conf.
Here's a tutorial: [Configuring Networking|http://solaris-x86.org/documents/tutorials/network.mhtml ] (kind of dated, but most of the info is still relevant)
john

How to setup vlans and routing between them

Hey guys
I am onboard a vessel where I have a Cisco 1921 router with intergrated 8-port dwitch. I have no experince what so ever with Cisco, onlye knowledge about netwrok in general.
What I need to do is to create 3 VLANs wit different networks and thier own gateways internally( no external routers, no external switches), and I want client in all networks to be able to communicate qith each other:
Vlan 2:
192.168.0.0
Default Gateway: 192.168.0.1
Network Mask: 255.255.255.0
Vlan 3:
192.168.1.0
Default Gateway: 192.168.1.1
Network Mask: 255.255.255.0
Vlan 4:
192.168.2.0
Default Gateway: 192.168.2.1
Network Mask: 255.255.255.0
As mentioned abode, I need clients from each VLAN to be able to communicate with each other. Se drawing

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
It might be as simple as defining VLAN interfaces for your 3 VLANs, and they assigning the ports to one of the 3 VLANs.

WRT1900ac cannot setup Vlan with ID 2

Hello,
I am configuring my new router wrt1900ac to use with my fiber supplier.
I have problem configuring Vlans for the diferent services.
For wrt1900ac to work with my fiber supplier I have to set diferent vlan:
Vlan 2 For TV
Vlan 3 For VoIP
Vlan 6 For Internet
These VLANs are already configured on the ONT Fiber and can not be changed.
I tryed to configure the Vlan 2 on one of the ports but , I get a message saying that you can only select between vlans 3-4094
http://imageshack.com/a/img822/4936/jtup.png
Why I cannot set this value?
There is a way to configure a Vlan in ID 2 ? Why only between 3 and 4094?
VoIP and Internet works fine.

I agree with FurryNutz. :-) Linksys Support Team are the best team to assist you with their device.

Solaris 10 VLAN

How setup VLAN on Solaris 10. Server have hme0 interface. When i make new file hostname.ce123000 for vlan 123 and plumb this interface, ifconfig say no such interface. How right setup vlans on this machine?

How setup VLAN on Solaris 10. Server have hme0 interface. When i make new file hostname.ce123000 for vlan 123 and plumb this interface, ifconfig say no such interface. How right setup vlans on this machine?It looks like you're slightly confused regarding the naming convention for the hostname.* files. You say that your system has hme0, but your hostname.* file is using a ce (Cassini Ethernet) interface. That's why it's not working and returning the "no such interface" message. Do you have any CE NICs in that system? The way you have the hostname.ce123000 file configured suggests you're trying to configure ce0 on VLAN ID 123.
The HME NIC is a very old interface and the driver doesn't support VLANs so you may need to update to a GLDv3 driver and NIC, something like CE, BGE, e1000g, etc. I believe in Solaris 11 the driver was updated to support GLDv3 so it may work.
What kernel rev are you running? Please provide "uname -a". If you can also provide a "prtdiag -v" we should be able to see what other NICs you have installed in the system (if any).
If you're running Solaris 10 3/05 and above refer to http://download.oracle.com/docs/cd/E19253-01/816-4554/fpjve/index.html
If you're running Solaris 10 3/05 and earlier, refer to http://download.oracle.com/docs/cd/E19253-01/816-4554/bbjfdeij/index.html
Regards,
Steve

Solaris 7 ldap client setup

Hi,
Please any one can help me in setting ldap client for solaris 7 guidelines or any website or docs help.
Thanking you,
Naren

hi mukherjee,
you can configure both solaris 8 and 9 as ldapclient to sunone 5.2 installed on solaris 9 box. make sure i think you cannot configure client on same maching on which directory server is installed.
No my question is how to setup ldapclient on solaris 6 andsolaris 7. as both does not support ldap. like solaris 7 has no nsswitch.ldap. can you provide me details to configure solaris7 as ldap client
PATEL

300 Series Switch VLAN Setup

Hello,
I am trying to setup vlans on sf 302 switch and been unsuccesful. My idea is having 2 separate networks and both connecting to internet
192.168.2.0/24 Gaming Network
192.168.3.0/24 Work Network
Router ( Linkys) connected to port 8 on the switch - 192.168.4.1
I have attached the serial cable and made the following changes
Creating VLAN's
Created Vlan 20 for gaming network
#config t
#vlan database vlan 20
exit
Created Vlan 30 for work
#config t
# vlan database vlan 30
#exit
Asigned ports to VLAN's
#config t
# int fa2
# switchport mode access
# switchport access vlan 20
#exit
#config t
#int fa3
# switchport mode access
# switchport access vlan 30
#exit
Assigning IP address to VLAN
#conf t
#int vlan 20
# ip address 192.168.2.1 255.255.255.0
#end
#conf t
#int vlan 30
# ip address 192.168.3.1 255.255.255.0
#end
I am stuck after this. Now i want to connect vlan 20 and vlan 30 on to router attached to port8 on switch so that computers on both vlans have access to internet. The IP address of router is
192.168.4.1.
Please explain what needs to be done to acomplish this.
Thanks
Maakri

Hello Randy,
The switch is already set to router mode.
I have attached a belkin router on port 8 of the switch. The LAN IP of router is 192.168.4.2
On the switch I have configured port 8 as follows
#int fa8
#ip address 192.168.4.1
# switchport mode trunk
#switchport trunk allowed vlan add vlan 20
#switchport trunk allowed vlan add vlan 30
#no shutdown
#exit
#ip routing
From PC connected to vlan 20 and VLAN30 I can ping 192.168.4.1 but not 192.168.4.2. I want to access internet from my PC's on Vlan20 and VLAN30
I can ping PC in vlan30 from my pc in Vlan20 but cant access the router IP and so no internet. What am I missing? Please let me know
Thank you
Maakri

VLan setup for a 2950 and 2611

Im trying to setup a real basic VLan setup for 1 2950 switch. I would like to have 3 Vlans on it including the default Vlan. So my understanding is that for all 3 of the VLans to talk to each other I will need a router to be the layer 3 device that routes the Vlans.
On my 2611 it looks like this:
interface Ethernet0/0
no ip address
full-duplex
interface Ethernet0/0.1
encapsulation dot1Q 1 native
ip address 172.16.10.1 255.255.255.0
no snmp trap link-status
interface Ethernet0/0.2
encapsulation dot1Q 2
ip address 172.16.20.1 255.255.255.0
no snmp trap link-status
interface Ethernet0/0.3
encapsulation dot1Q 3
ip address 172.16.30.1 255.255.255.0
no snmp trap link-status
Then my 2950 looks like this:
interface FastEthernet0/1
description Connection to router
switchport mode trunk
speed 10
duplex full
interface FastEthernet0/2
switchport access vlan 2
interface FastEthernet0/3
switchport access vlan 3
interface Vlan1
ip address 172.16.10.2 255.255.255.0
no ip route-cache
ip default-gateway 172.16.10.1
Ok so as it currently stands the switch and router will not talk to each other at all. From the switch I can not ping the router and vice a versa. If I plug a laptop into one of the ports using VLan1 I can ping the switch IP 172.16.10.2 but obviously can not ping the default gateway which is the router...
I didnt think this looked very hard but for some reason it does not want to work for me at all...
Any ideas?
LR

I have two things you might try. First set your trunking interface on your switch to auto.
interface fastethernet 0/1
speed auto
duplex auto
This will help to make sure that the ethernet on the 2611 will negotiate the duplex with the switch. I've had issues with 2611's trying to do full duplex on there ethernet ports.
Another Option turn on CDP on your router and switch and do a show cdp neighbor to make sure there plugged into the right ports.
Three you could move the vlan 1 ip address on the 2611 to the main interface. Example below. Then try pinging the switch. Your other tagged vlans should still work at that point. Also if you have multiple switches make sure to setup Vlan Trunk Protocol see NOTE A.
no interface Ethernet0/0.1
no encapsulation dot1Q 1 native
no ip address 172.16.10.1 255.255.255.0
no snmp trap link-status
interface Ethernet0/0
ip address 172.16.10.1 255.255.255.0
NOTE A
Add the following commands to each switch to setup your Vlan Trunk Protocol. These are pretty much the minimum amount of commands you can use to setup VTP.
vtp domain CISCO1
vtp version 2

Pvlan on solaris 11?

is it possible to setup pvlan's(private VLAN) on Solaris 11?

Thanks for the update, We would love to have such a feature will greatly help in traffic isolation while still on the same vlan.

VLAN's

Please assist me with the following scenario.
I am trying to setup vlans on a Solaris box.
The interface is called �ce0�
The vlan numbers are 27 and 301.
Am I correct in issuing the following commands?
#/usr/sbin/ifconfig ce27000 plum up
#/usr/sbin/ifconfig ce301000 plum up
If the interface was called �ce1�
Are the following commands correct?
#/usr/sbin/ifconfig ce27001 plum up
#/usr/sbin/ifconfig ce301001 plum up
And lastly, how do I make these settings permanent via files?
Thanks.
[email protected]

Like you create a virtual ip address like this.
ifconfig hme0:1 plumb up # plumbing the interface
ifconfig hme0:1 192.168.0.1 netmask xxxx.xxxx.xxxx.xxxx up # netmask is optional
Now edit /etc/hosts file. (make this entry)
192.168.0.1 host21
This entry makes it possible to ping your system by it's name.
To make PERMANENT VIRTUAL ADDRESS; with reference to above scenario
touch /etc/hostname.hme0:1
echo host21 > /etc/hostname.hme0:1
When the system boots, it reads this file and configures (using ifconfig) this hme0:1 using IP address present in /etc/hosts file.
Hope this helps!

Help with VLANs on SG200-18 and two SG200-08 switches

Hi everybody. My apologies but I'm only average at best with my CISCO skills. I have simple setup running a few network devices connected via 3 CISCO switches. It's small office and there are two rooms - one with servers and one with printer and pc's. Each room has 8-port SG200-08 switch.
Router/ firewall is Sonicwall TZ215 and it handles internal routing between VLAN's. Each SG200-08 was connected directly to TZ215 (no SG200-18 yet) and VLANs were working perfectly. Please see diagram below...
Problems started when I added in the middle larger SG200-18 to handle extra devices. Whatever I'm doing wrong but I can't make VLANs work anymore. Something I'm not setting up correctly in SG200-18.
Please help me to setup VLANS here - tagged, untagged, PVID, trunk........ I'm completely lost and already had to reset SG200-18 twice.
My working setup without 18 port switch was like this.
SG200-08 (1)
    g1 Trunk 1     1U,100T
    g2 Trunk 1     1U
    g3 Trunk 1     1U
    g4 Trunk 1     1U
    g5 Trunk 1     1U
    g6 Trunk 1     1U           SERVER3
    g7 Trunk 100   100U      SERVER1
    g8 Trunk 100   100U      SERVER2
SG200-08 (2)
    g1 Trunk 1     1U,50T,200T
    g2 Trunk 1     1U
    g3 Trunk 1     1U
    g4 Trunk 1     1U         PC1A
    g5 Trunk 1     1U         PC1B
    g6 Trunk 50    50U      PC2A
    g7 Trunk 50    50U      PC2B
    g8 Trunk 200   200U    NETWORK PRINTER
Thank you in advance.

Hello,
Small switches would remain untouched but 200-18 needs to have the following settings:
g15 Trunk 1     1U,100T
g16 Trunk 1     1U,50T,200T
g17 Trunk 1     1U,50T,200T
g18 Trunk 1 1U,50T,100T,200T
Sonicwall now would have only one port connected to SG200-18 with settinngs matching port g18 on big switch.
If you notice there is a change as now you would have only 1 port connecting your network to the Sonicwall, would advise you to use port 17 or 18 since they are uplink ports.
If you have tried to connect two ports to big switch STP would block one of the ports.
Let me know how it is going :-)
Aleksandra

Linux install server and solaris 10

Hi,
I am trying to learn Solaris as a student. I bought a SPARC (Netra T105 UltrasparcII) server on ebay which requires a network install as there is no cd-rom, or keyboard.
I only have a linux box (like I said, I'm a stingy student) to use as an install server, there is a few tutorials out there to try and do this, but none for Solaris 10. I have been hacking away at this for days, but cannot get it to install. I have the sparc server using RARP and then getting the /etc/bootparams file and downloading the boot files, but it does not get to locating the jumpstart files or the install files (I dont know if I can install from the terminal using the keyboard (without jumpstart) - I have not got that far yet).
I always get this, like it cannot find the install directory, I was wireshark on the linux boot server and see loads of NFS traffic after the TFTP download, but cannot seem to see what part it actually at. I have a detailed log at the bottom from putty. Any help greatly appreciated.Cheers
ERROR: bpgetfile unable to access network
/sbin/install-discovery: information: not found
Linux box setup:
/etc/bootparams
solaris root=192.168.2.10:/home/sunos/Solaris_10/Tools/Boot rootopts=rsize=32768 boottype=:in install=192.168.2.10:/home/sunos_install/Solaris_10/Product sysid_config=192.168.2.10:/home/sunos_install/jumpstart/sysidcfg install_config=192.168.2.10:/home/sunos_install/jumpstart/jumpstart.conf
TFTP setup from /tftpboot:
[root@robert tftpboot]# ll
total 232
lrwxrwxrwx 1 root root 8 Jun 10 13:55 C0A80214 -> inetboot
-rwxrwxrwx 1 root root 221280 Jun 10 13:47 inetboot
The Openboot can get ahold of the inetboot file and downloads and it and then loads it.
The following directories are exported through NFS
[root@robert sunos_install]# cat /etc/exports
#/home/nfs 192.168.2.0/24(ro,sync)
/home/sunos *(ro,no_root_squash)
/home/sunos_install *(ro,no_root_squash)
[root@robert tftpboot]# showmount -e localhost
Export list for localhost:
/home/sunos *
/home/sunos_install *
In /home/sunos, I have:
[root@robert sunos]# tree -L 2
|-- Solaris_10
| `-- Tools
|-- boot
| |-- hsfs.bootblock
| `-- sparc.miniroot
`-- lost+found
In /home/sunos_install, I have:
[root@robert sunos_install]# tree -L 2
|-- Solaris_10
| `-- Product
|-- jumpstart
| |-- jumpstart.conf
| `-- sysidcfg
`-- lost+found
[root@robert jumpstart]# cat jumpstart.conf
install_type initial_install
system_type server
partitioning explicit
filesys any 2000 /
filesys any 1500 swap
filesys any 1500 /var
filesys any 2000 /opt
geo N_America
cluster SUNWCreq
package SUNWgzip add
package SUNWless add
package SUNWman add
package SUNWbash add
package SUNWtcsh add
package SUNWzsh add
[root@robert jumpstart]# cat sysidcfg
system_locale=en_US
timezone=US/Pacific
terminal=xterms
name_service=NONE
timeserver=pool.ntp.org
security_policy=NONE
root_password=xxxx
network_interface=primary
{ hostname=js-test
ip_address=192.168.2.20
netmask=255.255.255.0
protocol_ipv6=yes}
Putty log file from console:
root server: 192.168.2.10 (192.168.2.10)
root directory: /home/sunos/Solaris_10/Tools/Boot
module /platform/sun4u/kernel/sparcv9/unix: text at [0x1000000, 0x10a096d] data at 0x1800000
module /platform/sun4u/kernel/sparcv9/genunix: text at [0x10a0970, 0x12615bf] data at 0x1867cc0
module /platform/sun4u/kernel/misc/sparcv9/platmod: text at [0x12615c0, 0x12615c7] data at 0x18bdf80
module /platform/sun4u/kernel/cpu/sparcv9/SUNW,UltraSPARC-IIi: text at [0x1261600, 0x126da07] data at 0x18be680
SunOS Release 5.10 Version Generic_139555-08 64-bit
Copyright 1983-2009 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
\|/Ethernet address = 8:0:20:c2:1b:b4
-Using default device instance data
\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/mem = 1048576K (0x40000000)
avail mem = 846602240
root nexus = Netra t1 (UltraSPARC-IIi 440MHz)
pseudo0 at root
pseudo0 is /pseudo
scsi_vhci0 at root
scsi_vhci0 is /scsi_vhci
ramdisk0 at root
ramdisk0 is /ramdisk-root
root on /ramdisk-root:a fstype ufs
pseudo-device: dld0
dld0 is /pseudo/dld@0
pcipsy0 at root: UPA 0x1f 0x0
pcipsy0 is /pci@1f,0
PCI-device: pci@1,1, simba0
simba0 is /pci@1f,0/pci@1,1
SUNW,hme0 : PCI IO 2.0 (Rev Id = c1) Found
SUNW,hme0 : Local Ethernet address = 8:0:20:c2:1b:b4
PCI-device: network@1,1, hme0
hme0 is /pci@1f,0/pci@1,1/network@1,1
SUNW,hme1 : PCI IO 2.0 (Rev Id = c1) Found
SUNW,hme1 : Local Ethernet address = 8:0:20:c2:1b:b5
PCI-device: network@3,1, hme1
hme1 is /pci@1f,0/pci@1,1/network@3,1
PCI-device: ebus@1, ebus0
ebus0 is /pci@1f,0/pci@1,1/ebus@1
su0 at ebus0: offset 14,3803f8
su0 is /pci@1f,0/pci@1,1/ebus@1/su@14,3803f8
cpu0: UltraSPARC-IIi (portid 0 impl 0x12 ver 0x91 clock 440 MHz)
iscsi0 at root
iscsi0 is /iscsi
|pseudo-device: zfs0
zfs0 is /pseudo/zfs@0
Configuring devices.
/pseudo-device: devinfo0
devinfo0 is /pseudo/devinfo@0
PCI-device: pci@1, simba1
simba1 is /pci@1f,0/pci@1
pseudo-device: pseudo1
pseudo1 is /pseudo/zconsnex@1
/pci@1f,0/pci@1,1/network@1,1 (hme0) online
/pci@1f,0/pci@1,1/scsi@2 (glm0):
Rev. 3 Symbios 53c875 found.
PCI-device: scsi@2, glm0
glm0 is /pci@1f,0/pci@1,1/scsi@2
PCI-device: pci@1, pci_pci0
pci_pci0 is /pci@1f,0/pci@1/pci@1
su1 at ebus0: offset 14,3602f8
su1 is /pci@1f,0/pci@1,1/ebus@1/su@14,3602f8
ecpp0 at ebus0: offset 14,340278
ecpp0 is /pci@1f,0/pci@1,1/ebus@1/ecpp@14,340278
pseudo-device: fssnap0
fssnap0 is /pseudo/fssnap@0
pseudo-device: ramdisk1024
ramdisk1024 is /pseudo/ramdisk@1024
sd0 at glm0: target 1 lun 0
sd0 is /pci@1f,0/pci@1,1/scsi@2/sd@1,0
pseudo-device: winlock0
winlock0 is /pseudo/winlock@0
pseudo-device: llc10
llc10 is /pseudo/llc1@0
pseudo-device: lofi0
lofi0 is /pseudo/lofi@0
pseudo-device: fcp0
fcp0 is /pseudo/fcp@0
pseudo-device: fcsm0
fcsm0 is /pseudo/fcsm@0
pseudo-device: trapstat0
trapstat0 is /pseudo/trapstat@0
pseudo-device: pool0
pool0 is /pseudo/pool@0
pseudo-device: mem_cache0
mem_cache0 is /pseudo/mem_cache@0
pseudo-device: fcode0
fcode0 is /pseudo/fcode@0
-\i2c0 at ebus0: offset 14,600000
i2c1 at ebus0: offset 14,100000
i2cadc0 at i2c0: reg=0x0:0x9E, name=bus,address="0,9e"
i2cadc0 is /pci@1f,0/pci@1,1/ebus@1/i2c@14,600000/adc@0,9e
i2cgpio0 at i2c0: reg=0x0:0x70, name=bus,address="0,70"
i2cgpio0 is /pci@1f,0/pci@1,1/ebus@1/i2c@14,600000/gpio@0,70
i2cgpio1 at i2c0: reg=0x0:0x72, name=bus,address="0,72"
i2cgpio1 is /pci@1f,0/pci@1,1/ebus@1/i2c@14,600000/gpio@0,72
|/-\|/-\|/-Using RPC Bootparams for network configuration information.
Attempting to configure interface hme1...
\|/-\|/-WARNING: hme1: fault detected in device; service degraded
WARNING: hme1: No response from Ethernet network : Link down -- cable problem?
\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-Skipped interface hme1
Attempting to configure interface hme0...
Configured interface hme0
ERROR: bpgetfile unable to access network
/sbin/install-discovery: information: not found

rmcnaught48 wrote:
Hi,
I am trying to learn Solaris as a student. I bought a SPARC (Netra T105 UltrasparcII) server on ebay which requires a network install as there is no cd-rom, or keyboard.
I only have a linux box (like I said, I'm a stingy student) to use as an install server, there is a few tutorials out there to try and do this, but none for Solaris 10. I have been hacking away at this for days, but cannot get it to install. I have the sparc server using RARP and then getting the /etc/bootparams file and downloading the boot files, but it does not get to locating the jumpstart files or the install files (I dont know if I can install from the terminal using the keyboard (without jumpstart) - I have not got that far yet).You can install using the keyboard with jumpstart. Without jumpstart you'd need local media (you can't enter the OS via the keyboard).
I always get this, like it cannot find the install directory, I was wireshark on the linux boot server and see loads of NFS traffic after the TFTP download, but cannot seem to see what part it actually at. I have a detailed log at the bottom from putty. Any help greatly appreciated.Cheers
ERROR: bpgetfile unable to access network
/sbin/install-discovery: information: not foundHmm. That looks like the image file is corrupt. Can you pull the image from media again? Can you see if there's a /sbin/install-discovery file in the image (usually under Tools/Boot/root). I recall there used to be a problem with that file.
Linux box setup:
/etc/bootparams
solaris root=192.168.2.10:/home/sunos/Solaris_10/Tools/Boot rootopts=rsize=32768 boottype=:in install=192.168.2.10:/home/sunos_install/Solaris_10/Product sysid_config=192.168.2.10:/home/sunos_install/jumpstart/sysidcfg install_config=192.168.2.10:/home/sunos_install/jumpstart/jumpstart.confIf you just want an interactive install (prompt for configuration/settings), you don't need sysid_config or install_config. Those are for automated installations.
TFTP setup from /tftpboot:
[root@robert tftpboot]# ll
total 232
lrwxrwxrwx 1 root root 8 Jun 10 13:55 C0A80214 -> inetboot
-rwxrwxrwx 1 root root 221280 Jun 10 13:47 inetboot
The Openboot can get ahold of the inetboot file and downloads and it and then loads it.
The following directories are exported through NFS
[root@robert sunos_install]# cat /etc/exports
#/home/nfs 192.168.2.0/24(ro,sync)
/home/sunos *(ro,no_root_squash)
/home/sunos_install *(ro,no_root_squash)
[root@robert tftpboot]# showmount -e localhost
Export list for localhost:
/home/sunos *
/home/sunos_install *That looks pretty good.
You do have the option of running VMware on linux, and putting a Solaris 10 image on it, then using that VM as your boot server. But the problem you're displaying doesn't appear to be related to the linux server.
Darren

Setup vlan on solaris

Similar Messages

Maybe you are looking for