Setup VPN

I am trying to setup a VPN connection between to sites (home and office). Want the home computers to be able to see the office computers as one network. Going to be configuring a VPN server at the home. What do I need to setup in the Linksys?.
The VPN server will be connected to the WRT54GS router at the house.

If you have setup a VPN server and it will be connected to WRT54GS Router, you need to open Some port for the VPN on your Router.This are the Port numbers which you need to Open on your Router. Port 47, Port 1723, 500 and 1701.
OR
You can set the Static IP to your VPN server and enable the DMZ on the Router and this will open all the ports on the Router for your VPN server.

Similar Messages

I am trying to setup VPN with QuickVPN

Hi I am trying to setup VPN with WRVS4400N and Quick VPN on client side. I am fairly new to VPN and did some research and looked through the manual but can't seem to get it to work so far and from what I noticed many people are having this problem. So hopefully someone can tell what the problem is or at least point to right direction on solving this.
Basically it gives the "Failed to establish connection" generic error, shows it almost instantly..
It also showed the certificate error before but then I read about putting it in the installation directory and it stopped showing it, and whats strange is later I removed it but it doesnt show the error any longer, so don't know if its caching it somewhere or what can be going on...
In effort to look for answer and test things out I tried to connect to another location and setup a WRV200 router, I also get the same error but not instantly, it even shows "Activating Policy" but then doesn't go farther and shows the generic error...
Also with this setup strangly it always shows the certificate error, no matter if I put one in directory or not... Even tried to name it as the WRVS4400N certificate name...
Anyway VPN IPSec is disabled, and Client Accounts are configured and changed password several times to make sure its correct, VPN Passthrough enabled on all 3 options.
I tried to disable Windows Router, I also have a router in place do I possibly need to open some type of ports for the QuickVPN client?
Don't know yet whats going on if I am missing something or if there is some problem that needs work-around but if you know the answer or guesses of answer please let me know.

Hi Aleksandr,
since this question is about a product in the Cisco Small Business / Linksys range, I suggest you move it to the community, where you will have a better chance of getting expert advice.
best regards,
Herbert
Cisco Moderator

Do I need a security license to setup VPN on router?

Hi All.
I'm trying to setup VPN connections on 2 different routers and I'm not sure about that Do I need a security license to setup VPN connection on router?
First one is 1941-K9 site-to-site.
Second one is 887G-K9, EasyVPN connection.
Both of them don't work properly. What do I need to check on both routers to see if they're abled for vpn connection, maybe some commands as well.
Thanks in advance.
Regards,

yes, for VPN you need a security-license.
The 1941 should show the following line:
rtr-01#sh ver | b Technology
Technology Package License Information for Module:'c1900'
Technology    Technology-package          Technology-package
              Current       Type          Next reboot
ipbase        ipbasek9      Permanent     ipbasek9
security      securityk9    Permanent     securityk9
data          None          None          None
The 887 comes by default with the "Advanced Security" feature-set. That's all you need for that device.
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni

Cannot setup VPN (WMI failure?) - Server Essentials 2012 R2

Hi,
Last week i setup a new Server Essentials 2012 R2 (fresh install). Everything apart from the Anywhere Access has sucessfully been setup and the server is in a production Environment.
When i try to configure Anywhere Access and setup VPN + RemoteDesktop , the wizard fails. VPN cannot be setup , retry.
Two Issues:
The VPN setup/configuration fails (Lets start with this one, could be related to second issue).
Remote Desktop setup is completed. However the "Remote Desktop Gateway" service cannot be started because the dependant service RPC/HTTP Load Balancing cannot start.
Troubleshooting steps taken on the VPN setup Issue:
Restarting the server (multiple times)
Rerunning the wizard (multiple times)
Checking if the correct roles has been installed by Server Essentials
Checking log files dashboard.log (The error found)
Run sfc /scannow (errors found and corrected)
Run DISM (OK)
Tried to setup VPN manually using the RRAS GUI (Error: Installation of the Routing and Remote Access service failed because Class not registered 80040154)
Further I've concluded that the 1st (VPN) issue is probably casued by malfunctioning WMI
In the dashboard.log , when running the VPN setup an error can be found on one of the setup steps:
[6684] 140723.170909.2619: RemoteAccess: PS > RemoteAccess\Install-RemoteAccess -VpnType Vpn;
[3320] 140723.170910.1772: DomainManagerObjectModel: Calling KeepAlive for instanceID=1
[3320] 140723.170910.1772: DomainManagerObjectModel: KeepAlive succeeded for instanceID=1
[6684] 140723.170918.1943: RemoteAccess: PS Exception (catch and rethrow): System.Management.Automation.MethodInvocationException: Exception calling "EndProcessing" with "0" argument(s): "Object reference not set to an instance
of an object." ---> System.NullReferenceException: Object reference not set to an instance of an object.
To troubleshoot this further, i've run the PS command "Install-RemoteAccess -VpnType Vpn" manually. This gives me the following error which Points to a WMI issue
PS C:\Windows\system32> RemoteAccess\Install-RemoteAccess -VpnType Vpn
RemoteAccess\Install-RemoteAccess : Provider load failure
At line:1 char:1
+ RemoteAccess\Install-RemoteAccess -VpnType Vpn
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    + CategoryInfo          : NotSpecified: (PS_RemoteAccess:root/Microsoft/...PS_RemoteAccess) [Install-RemoteAccess]
   , CimException
    + FullyQualifiedErrorId : HRESULT 0x80041013,Install-RemoteAccess
Ran WMIdiag - Found errors. The most interesting error is found below
53059 22:43:35 (2) !! WARNING: WMI provider DCOM registrations missing for the following provider(s): ..................................... 3 WARNING(S)!
53060 22:43:35 (0) ** - ROOT/CIMV2/TERMINALSERVICES, AAGProvider ({75D15B16-228C-499F-A0FC-E4899AC870CE}) (i.e. WMI Class 'Win32_TSGatewayResourceGroup')
53061 22:43:35 (0) **   Provider DLL: ''
53062 22:43:35 (0) ** - ROOT/WEBADMINISTRATION, WebAdministrationProvider ({84951D16-922E-4692-B4E9-90DD80426ECF}) (i.e. WMI Class 'SiteContainsConfigurationSection')
53063 22:43:35 (0) **   Provider DLL: ''
53064 22:43:35 (0) ** - ROOT/MICROSOFT/WINDOWS/REMOTEACCESS/SERVER, RAServerPSProvider ({BEF7FC3B-203F-4AD6-B38E-A1F519202644})
53065 22:43:35 (0) **   Provider DLL: ''
The WMIDiag provider CSV shows that the RASERVERPSPROVIDER.DLL has no DCOM (WMI Provider Binary) registration. (see example below)
WMI Namespace
WMI Class name
WMI Provider Name
WMI Provider Model
WMI provider binary
WMI provider registration MOF file(s)
ROOT/MICROSOFT/WINDOWS/REMOTEACCESS/SERVER
PS_RemoteAccessLocal
RAServerPSProvider
No DCOM registry registration
No DCOM registry registration
C:\WINDOWS\SYSTEM32\WBEM\RASERVERPSPROVIDER.MOF
So I've tried to reregister the DLLs with regsvr32 RASERVERPSPROVIDER.DLL. I've also tried to recompile the MOFs (RASERVERPSPROVIDER.MOF). I found the missing DLL and MOF using WMIDiag on Another Server Essentials 2012 R2 machine. But no sucess - the WMI
Provider binaries and model are still missing..
Example from another (healty) 2012 R2 Essentials Server
WMI Namespace
WMI Class name
WMI Provider Name
WMI Provider Model
WMI provider binary
WMI provider registration MOF file(s)
ROOT/MICROSOFT/WINDOWS/REMOTEACCESS/SERVER
PS_RemoteAccessLocal
RAServerPSProvider
In-proc
C:\WINDOWS\SYSTEM32\WBEM\RASERVERPSPROVIDER.DLL
C:\WINDOWS\SYSTEM32\WBEM\RASERVERPSPROVIDER.MOF
Is there any other way to add the WMI provider binary manually? Or do you think I'm on the wrong track?
Thank you in advance.
Regards
Josef
Support Engineer
(MCP) Microsoft Certified Professional
(MCTS) Exchange Server 2010, Configuring
(CCNA) Cisco Certified Network Associate

Hi,
Here is a good blog to troubleshoot WMI issues.
WMI: Rebuilding the WMI Repository
http://blogs.technet.com/b/askperf/archive/2009/04/13/wmi-rebuilding-the-wmi-repository.aspx
First, I want to confirm if the good system is at the same hotfix/SP.
Re-register all of the dlls and recompile the .mofs in the wbem folder and re-registering WMI Service and Provider. Then verify the consistence of the repository.
If the issue persists, we can choose to rebuild the repository.
Hope this helps.

Need help in setup vpn with IGMP enabled !

hi all
i hve cisco 2901 router and i want to setup vpn that allow IGMP ,
can somebody help me with it or at least sample configuration ?
can it be done from http gui ? or it is mandatory from cli ?
regards

Hello,
So you plan to send multicast traffic over the tunnel?
It could be possible to do it via both ways, thing is is harder to get assistance via GUI as for example I have no access to any router. I reply based on commands that I remember so CLI is a must.
I would recommend using a GRE tunnel to send the Multicast traffic through it
Looking for some Networking Assistance?
Contact me directly at [email protected]
I will fix your problem ASAP.
Cheers,
Julio Carvajal Segura
http://laguiadelnetworking.com

Setup vpn in ASA 5505

We have a hosted server with a new provider and we also opted for a firewall which is a ASA 5505. It turns out that they do not provide assistance with the firewall, so I have come here!
The server hosts multiple customer websites, along with both MySQL and SQL Server databases.
I would like to provide customers with the ability to connect to their databases remotely, for which I assume we need to create a VPN to allow them access through the firewall. Also, I would want them to be able to use the standard Windows connection tool(s).
Unfortunately, I know very little about this so I am looking for idiot-proof help ;-)
First of all, is this a safe thing to do - can I control what they can access on the server end?
What type of VPN do I need? I looked at one of the wizards and stopped at the point when it started talking about IP addresses ... what range should I / can I use? How does that relate to our server setup, or doesn't it?
I don't know what else to ask ... hopefully you can guide me in the right direction!

Can you add this:
tunnel-group 64.53.58.229 type ipsec-l2l
tunnel-group 64.53.58.229 ipsec-attributes
pre-shared-key
Another thing i have noticed is the disconnect between the WAN IP (VLAN 2) and default gateway next hop IP address.
nterface Vlan2
nameif inside
security-level 100
ip address 204.116.85.166 255.255.255.0
route outside 0.0.0.0 0.0.0.0 207.144.35.1 1
Please rate replies and mark question as "answered" if applicable.

Setup VPN on Mac Mini Server running OSX through a BT Hub Router

Hello everyone,
I know this question has been posted several times and I have looked at the suggested solutions, trying each of them. I think this is really down to my lack of knowledge hence hoping someone out there could point me to the right direction for more resources / information, please.
I am trying to setup a Mac Mini Server with VPN access. My server sits behind a BT Hub router. These are the steps that I have been through:
1. I am using the server app and after registering a free account with no-ip, I got myself a host name <myname>.ddns.net.
2. Then I setup the server using a domain name
3. I configured the DNS by first setting up a primary zone - zone: ddns.net. Then added machine record host name: <myname> pointing to my server which I have configured my router to assign a static ip address to it at 192.168.x.x
4. Then, I configured the VPN setting up for L2TP and PPTP, setup the shared secret, change the ip address range to match that of the DHCP range on my router. My router by default has a DHCP range between 64 - 253.
5. Then, I also configured my router to port forward 500, 1701, 1723, and 4500 to my server at 192.168.x.x (I selected both TCP and UDP).
6. Finally, setup a user account with account name test and password abcd12345
7. Gone on my "client" machine which is basically my Samsung S4 handphone, selected VPN -> PPTP -> server address: <myname>.ddns.net -> entered account name test and password abcd12345.
This didn't work.
Then, I read some post about manually configure DHCP on the server app. Went on the server app, turned on DHCP and setup a network named TestDHCP. Assigned ip address range between that of the default DHCP range on my BT Hub router.
This does not work either.
Could someone please kindly help me with it? I am completely lost.
Thank you in advance.

To run a public VPN server behind an NAT gateway, you need to do the following:
1. Give the gateway either a static external address or a dynamic DNS name. The latter must be a DNS record on a public DNS registrar, not on the server itself. Also in the latter case, you must run a background process to keep the DNS record up to date when your IP address changes.
2. Give the VPN server a static address on the local network, and a hostname that is not in the top-level domain "local" (which is reserved for Bonjour.)
3. Forward external UDP ports 500, 1701, and 4500 (for L2TP) and TCP port 1723 (for PPTP) to the corresponding ports on the VPN server.
If your router is an Apple device, select the Network tab in AirPort Utility and click Network Options. In the sheet that opens, check the box marked
Allow incoming IPSec authentication
if it's not already checked, and save the change.
With a third-party router, there may be a similar setting.
4. Configure any firewall in use to pass this traffic.
5. Each client must have an address on a netblock that doesn't overlap the one assigned by the VPN endpoint. For example, if the endpoint assigns addresses in the 10.0.0.0/24 range, and the client has an address on a local network in the 10.0.1.0/24 range, that's OK, but if the local network is 10.0.1.0/16, there will be a conflict. To lessen the chance of such conflicts, it's best to assign addresses in a random sub-block of 10.0.0.0./0 with a 24-bit netmask.
6. "Back to My Mac" is incompatible with the VPN service. It must be disabled both on the server and on an AirPort router, if applicable.
If the server is directly connected to the Internet, see this blog post.

[WRT54G v.5] Cannot setup VPN to work due to IP conflict

Hi,
I am completely ignorant about routers and networking and I've tried to read through threads that seem related to my problem but didn't find a solution. So I will try to give as much information as I can and hopefully someone can help me out!
Router: WRT54G v5, Firmware v1.01.0, Default Gateway: 192.168.2.1
VPN Client Software: Check Point VPN-1 SecuRemote, NG with Application Intelligence R56 HFA-03 (Build 619)
Situation: PCs at work have IP addresses starting with 192.168.*, which conflicts with the IP address assign to my home PC
Thanks in advance for any input here!

How have you configured your router before if it is using 192.168.2.1?
Connect to the web-based interface of the router. The default address is http://192.168.1.1/ but if you have changed it it would be http://192.168.2.1/ for you. It will ask for a username and password. The default password is "admin" there (no username) but I hope you have changed it before. If not, this would be a good time to do it...
The setup page appears in the browser. Somewhere in the middle of the screen is the Network Setup section where you define the Local IP Address of the router and the subnet mask. Change the local IP address to whatever base address you like... save the settings... done.
For further configuration you must now point your browser to the new IP address obviously. If you are using DHCP on your computer you must renew the DHCP address. I guess a "Repair" of the network connection should do. If you have a static IP address you must change it that it is in the new LAN. After your computer has a proper IP address in the new LAN it can connect again to the router under the new IP address and it should also be able to use the internet connection of the router (or whatever else is connected on the internet port of the router)

How to setup vpn-server in Mountain Lion 10.8.3?

Before I updated my mac mini server to 10.8.3 I used Server Admin to setup a vpn server. After the update Server Admin isn't supported anymore and my vpn settings are gone. Now i want to setup the server again, but have no clue what settings to enter where.
I suppose it starts with adding two vpn-interfaces: PPTP and LT2P.
But how further? I can't find a tutorial or manual.

I do now :-)
And many thank, that's the application I was looking for. My vpn is back online. Well, the mac-part. I still can't connect with a Win7 system. Connecting to a vpn-server of another company works fine, so it's something in the configuration of de Mini Server.
The error code is 629.
Hopefully someone can help me with this part too?

Need Support to setup VPN Client on macbook pro

Can somebody help me to create VPN client on my mac book pro.
I have following information of server.
Name:
Type: IPSec XAuth PSK
Server:
IPSec identifier:
IPSec pre-shared key:
DNS Server:
Authentication prompt:
username:
password:
Thanks

You set up your client for VPN access using System Preferences (under the Apple menu) > Network.
Create a new connection by clicking the "+" button in the lower left corner. In the resulting dialog, set Interface to VPN and VPN Type to Cisco IPSec. Click the Create button.
Select the new VPN connection from the list. Enter the Server Address, Account Name, and Password. Click the Authentication Settings... button and enter the required information.
DNS Servers should be entered after clicking the Advanced... button.
When all settings are entered, click the Apply button.
Test the set up by clicking the Connect button.
You may want to check the Show VPN status in menu bar checkbox. This lets the user connect immediately from a menu without having to go to through System Preferences.
Best of luck.

Could setup VPN but could not connect to the server behind Windows

Hello,
Server 1 and Server 2 are directly connect with cable. Server 1 has 2 NIC.
I want to configure the following network, already have done most of the steps.
Install the Role “Network Policy and Access Services.My
router is configured to assign ip to NIC1 and Linux server. I enabled IP forwarding in Win server from registry. My clients are able to connect to
VPN -> and ping Server 1. But they are unable to ping Server 2 through VPN. But
I am able to ping Server 2 directly from Server 1. Are Server 1 and Server 2 not in same LAN ? Should not outside users be able to ping Server 2 after successful VPN connect ?
Please help with conceptual errors.

Hi,
According to your description, my understanding is that VPN client failed to ping internal devices after connecting to VPN server.
Ping command is used to detect network or host communication failures and troubleshoot common TCP/IP connectivity problems by sending ICMP echo request messages and record the receipt of ICMP echo reply messages. Turn off firewalls and protection software(if
any) and then try to ping again. And, ping IP address instead of name.
You have mentioned “enabled IP forwarding in Win server from registry”, since you have installed RRAS on VPN server, if you want the remote access clients to have access to resources on the intranet, I recommend you to enable NAT on VPN server.
Besides, according to the picture, 2 NICs of VPN server and the Linux server are on the same sub network. In general, NIC 2 connects to internal network and NIC1 connect to external network. I recommend you to reference the link below for
Step-by-Step Guide for Setting Up VPN-based Remote Access in a Test Lab(similar configuration with your VPN)：
https://technet.microsoft.com/en-us/library/cc757206%28v=ws.10%29.aspx?f=255&MSPPError=-2147217396
Best Regards,
Eve Wang
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Howto setup VPN between RVS4000 and linux PC ?

The "vpnc" - cisco compatible vpn client is available in lastest version of Ubuntu.
Has anyone successed to establish a VPN?

WRT54G does not support IPsec VPN. You could try WRV210 instead.

VPN Client and Setup for RV042

Is there a definitive setup for a small VPN using the RV042?
Situation is 2 remote users wish to get access to a non server (W7P) pc to access files.
The end point doesn't have a static IP but I've put in a DYNDNS.org so it reports back the IP and I can access the router at least from outside.
I can setup VPN users but is there more to do?
Wish to use QVPN client or advise alternative.
Appreciate all input.
Thanks
Bruce

Bruce,
QuickVPN normally works well for what you wish to do. Make sure that the Windows Firewall is ON in Windows 7 and Windows Vista clients. Turn off all antivirus and third party firewall software as well at least until you have verified that you have a successful connection. It is very easy to set up, just create a username and password in the router. If you run into trouble, post here or call your local Small Business Support Center:
http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html

OS X server: VPN setup

Hi,
   I am using OS X server (10.9.1).   I try to setup VPN service.    But, I do not know what went wrong.    Below is the log.    Any tips?
1st time:   I use wwmm.wwmmhome.private...
2013-12-31 14:23:19 SGT     Incoming call... Address given to client = 192.168.1.240Tue Dec 31 14:23:19 2013 : Directory Services Authentication plugin initialized
Tue Dec 31 14:23:19 2013 : Directory Services Authorization plugin initialized
Tue Dec 31 14:23:19 2013 : publish_entry SCDSet() failed: Success!
Tue Dec 31 14:23:19 2013 : publish_entry SCDSet() failed: Success!
Tue Dec 31 14:23:19 2013 : publish_entry SCDSet() failed: Success!
Tue Dec 31 14:23:19 2013 : PPTP incoming call in progress from '183.90.37.225'...
Tue Dec 31 14:23:19 2013 : PPTP connection established.
Tue Dec 31 14:23:19 2013 : using link 0
Tue Dec 31 14:23:19 2013 : Using interface ppp0
Tue Dec 31 14:23:19 2013 : Connect: ppp0 <--> socket[34:17]
Tue Dec 31 14:23:19 2013 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0x729c77b1> <pcomp> <accomp>]
Tue Dec 31 14:23:19 2013 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x38d3186b> <pcomp> <accomp>]
Tue Dec 31 14:23:19 2013 : lcp_reqci: returning CONFACK.
Tue Dec 31 14:23:19 2013 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x38d3186b> <pcomp> <accomp>]
Tue Dec 31 14:23:22 2013 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0x729c77b1> <pcomp> <accomp>]
Tue Dec 31 14:23:22 2013 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x38d3186b> <pcomp> <accomp>]
Tue Dec 31 14:23:22 2013 : lcp_reqci: returning CONFACK.
Tue Dec 31 14:23:22 2013 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x38d3186b> <pcomp> <accomp>]
Tue Dec 31 14:23:22 2013 : rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0x729c77b1> <pcomp> <accomp>]
Tue Dec 31 14:23:22 2013 : sent [LCP EchoReq id=0x0 magic=0x729c77b1]
Tue Dec 31 14:23:22 2013 : sent [CHAP Challenge id=0xd5 <663e256443001f6c0163674232734908>, name = "wwmm.wwmmhome.private"]
Tue Dec 31 14:23:22 2013 : rcvd [LCP EchoReq id=0x0 magic=0x38d3186b]
Tue Dec 31 14:23:22 2013 : sent [LCP EchoRep id=0x0 magic=0x729c77b1]
Tue Dec 31 14:23:22 2013 : rcvd [LCP EchoRep id=0x0 magic=0x38d3186b]
Tue Dec 31 14:23:22 2013 : rcvd [CHAP Response id=0xd5 <63847a83bdb04f9fba56d82397d7213e00000000000000003d68f95fbd5d9f5e90ad10d4e8403c f53e5940402f913a6b00>, name = "test"]
Tue Dec 31 14:23:22 2013 : sent [CHAP Failure id=0xd5 ""]
Tue Dec 31 14:23:22 2013 : CHAP peer authentication failed for walter
Tue Dec 31 14:23:22 2013 : sent [LCP TermReq id=0x2 "Authentication failed"]
Tue Dec 31 14:23:22 2013 : Connection terminated.
Tue Dec 31 14:23:22 2013 : PPTP disconnecting...
Tue Dec 31 14:23:22 2013 : PPTP disconnected
2013-12-31 14:23:22 SGT       --> Client with address = 192.168.1.240 has hung up
2nd time, I use wwmm.dyndns.org
2013-12-31 14:38:38 SGT     Incoming call... Address given to client = 192.168.1.240Tue Dec 31 14:38:38 2013 : Directory Services Authentication plugin initialized
Tue Dec 31 14:38:38 2013 : Directory Services Authorization plugin initialized
Tue Dec 31 14:38:38 2013 : publish_entry SCDSet() failed: Success!
Tue Dec 31 14:38:38 2013 : publish_entry SCDSet() failed: Success!
Tue Dec 31 14:38:38 2013 : publish_entry SCDSet() failed: Success!
Tue Dec 31 14:38:38 2013 : PPTP incoming call in progress from '183.90.37.225'...
Tue Dec 31 14:38:39 2013 : PPTP connection established.
Tue Dec 31 14:38:39 2013 : using link 0
Tue Dec 31 14:38:39 2013 : Using interface ppp0
Tue Dec 31 14:38:39 2013 : Connect: ppp0 <--> socket[34:17]
Tue Dec 31 14:38:39 2013 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0x5b1829ce> <pcomp> <accomp>]
Tue Dec 31 14:38:39 2013 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x3298b0f1> <pcomp> <accomp>]
Tue Dec 31 14:38:39 2013 : lcp_reqci: returning CONFACK.
Tue Dec 31 14:38:39 2013 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x3298b0f1> <pcomp> <accomp>]
Tue Dec 31 14:38:42 2013 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0x5b1829ce> <pcomp> <accomp>]
Tue Dec 31 14:38:42 2013 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x3298b0f1> <pcomp> <accomp>]
Tue Dec 31 14:38:42 2013 : lcp_reqci: returning CONFACK.
Tue Dec 31 14:38:42 2013 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x3298b0f1> <pcomp> <accomp>]
Tue Dec 31 14:38:42 2013 : rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0x5b1829ce> <pcomp> <accomp>]
Tue Dec 31 14:38:42 2013 : sent [LCP EchoReq id=0x0 magic=0x5b1829ce]
Tue Dec 31 14:38:42 2013 : sent [CHAP Challenge id=0x5a <4a753b2e091d155a1414337d40401750>, name = "wwmm.dyndns.org"]
Tue Dec 31 14:38:42 2013 : rcvd [LCP EchoReq id=0x0 magic=0x3298b0f1]
Tue Dec 31 14:38:42 2013 : sent [LCP EchoRep id=0x0 magic=0x5b1829ce]
Tue Dec 31 14:38:42 2013 : rcvd [LCP EchoRep id=0x0 magic=0x3298b0f1]
Tue Dec 31 14:38:42 2013 : rcvd [CHAP Response id=0x5a <2f54770187524125079b5d74e01b09e800000000000000004359e904d9814bc5e0eb4bb880e7e5 23181a0d22b9164e2400>, name = "test"]
Tue Dec 31 14:38:42 2013 : DSAuth plugin: unsupported authen authority: recved ShadowHash;HASHLIST:<SALTED-SHA512,SMB-NT,CRAM-MD5,RECOVERABLE,SALTED-SHA512-PB KDF2>, want ApplePasswordServer
Tue Dec 31 14:38:42 2013 : DSAuth plugin: MPPE key required, but its retrieval failed.
Tue Dec 31 14:38:42 2013 : sent [CHAP Failure id=0x5a "S=8DDCFFC7EA287D3A141E5594392BCBD87C35F76B M=Access granted"]
Tue Dec 31 14:38:42 2013 : CHAP peer authentication failed for walter
Tue Dec 31 14:38:42 2013 : sent [LCP TermReq id=0x2 "Authentication failed"]
Tue Dec 31 14:38:42 2013 : Connection terminated.
Tue Dec 31 14:38:42 2013 : PPTP disconnecting...
Tue Dec 31 14:38:42 2013 : PPTP disconnected
2013-12-31 14:38:42 SGT       --> Client with address = 192.168.1.240 has hungup

The VPN server in Server.app is these days pretty feeble, it only does PPTP and L2TP and does not support using security certificates or VPN on demand. (Which requires security certificates.) As a result the security of Apples VPN server is only capable of functions which have all been successfully cracked. Now for most people that might not be too much of a concern but if your a law, health, finance, or government customer then it should be a concern.
However...
While the VPN server itself does not support clustering nor in fact do any of the services in Server.app there might be a way to achieve what you want. If you have a DNS load-balancer then you can point all the clients to the load-balancer and it will distribute the requests to two or more Apple VPN servers. You just need to make sure each Apple VPN server gives out a different range of IP addresses with no overlaps.

CISCO VPN (WRVS4400N) router setup

Dears,
Please help me to setup VPN connection,
Head office : fortigate 200b firewall - SSL, IPsec
Branch office: WRVS4400N Wireless-N Gigabit Security Router with VPN
Both side have the public IP

Wrong forum, post in "small business routers". You can move your posting using the actions panel on the rigth.

Setup VPN

Similar Messages

Maybe you are looking for