Setup wireless router with tablet

Bought a new Samsung tablet and a Cisco wi fi router. But I don't have the CD drive to activate the wi fi router. I am using the Cisco linksys E1200.

You can download the Cisco Connect Software here.
http://homesupport.cisco.com/en-apac/support/routers/E1200
You can also manually configure your E1200.
Follow the links below depending on your ISP type.
Setting-Up a Router with DSL Internet Service
Setting-Up a Router with Cable Internet Service
The Search Function is your friend.... and Google too.
How to Secure your Network
How to Upgrade Routers Firmware
Setting-Up a Router with DSL Internet Service
Setting-Up a Router with Cable Internet Service
How to Hard Reset or 30/30/30 your Router

Similar Messages

WRTP54G (wireless router with phone hookup) with Panasonic network camera BL-C30A (WEP only)

hi
I would like to use this wireless router with WEP so I can access the camera wirelessly (camera only does WEP encryption).
The camera should be the only device allowed to connect to this router wirelessly.
I can dedicate channel 11 so only this wireless router uses it
I know WEP can be cracked but I'm thinking maybe I can setup the router so it doesn't matter, i.e.,
so only the camera can be accessed through this particular router
so my questions are:
1. can I setup the router so only outgoing local LAN http requests are allowed?
2. any other suggestions on router setup that will prevent access to my network?
(using MAC address filtering (for camera mac address only) is worth doing but I guess MAC address can be spoofed so not a complete solution)
thanks,
Tom
Solved!
Go to Solution.

I think "toomanydonuts" has provided my solution in this thread:
solution thread
thanks,
Tom
Message Edited by coffee_addict on 01-03-2010 02:27 PM

Configure WRT54G Wireless Router with PUBLIC IP address and use DHCP for internal computers

Hi,I have an Internet online service with 5 public IP addresses. The router and the AP are connected to a switch. I would like to configure a WRT54G wireless router with one of this IP public Address and use DHCP (with private ip address) for the computers that will connect to the AP. As the AP is connected to the switch it is possible that other wired computers that are connected to the same switch can obtain an IP address from the DHCP ?
Thansk in advance

Thanks for your help. Please correct me if Im wrong. After connecte the equipments the way you suggestI setup a static IP address (The public IP) in the WRT54GI enable DHCP in the WRT54G with a range from 10.10.0.100 to 10.10.0.200 (as an example) The gateway is the Public IP address right ? How do I route the 10.10.0.x addresses to the public IP address. Thansk again

I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. Any tips on how to do this?

I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. I installed the current Bonjour printer services software on the Windows machine, and separately installed the driver software for the Epson printer on the WIndows machine. Running the bonjour wizard, I get an alert saying 'I don't have sufficient access to my computer to connect to the selected printer'.
The printer has 'sharing' turned on from the Mac end; this works with a Powerbook via the wireless connection. Sharing is also turned on in the Windows printer control panel for this printer (under properties). The Mac is a G5 running 10.5.8. When I try to print a page from the Windows machine it gets hung in the print queue.
Any advice how to proceed would be appreciated!
thx,

I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. I installed the current Bonjour printer services software on the Windows machine, and separately installed the driver software for the Epson printer on the WIndows machine. Running the bonjour wizard, I get an alert saying 'I don't have sufficient access to my computer to connect to the selected printer'.
The printer has 'sharing' turned on from the Mac end; this works with a Powerbook via the wireless connection. Sharing is also turned on in the Windows printer control panel for this printer (under properties). The Mac is a G5 running 10.5.8. When I try to print a page from the Windows machine it gets hung in the print queue.
Any advice how to proceed would be appreciated!
thx,

HI I HAVE WRT54G WIRELESS ROUTER WITH VERSION 7. NOW I W...

HI
I HAVE WRT54G WIRELESS ROUTER WITH VERSION 7.
NOW I WANTED TO UPGRADE THE FIRMWARE.
I CHCAKED OUT THE SITE I COULD'NT FIND THE DRIVERS FOR THE VER 7
EVERYTHING ELSE OTHER THAN VER 7 IS PRESENT ON SITE I WANTED TO CHEAK OUT WHEATHER THE VER 7 FIRMWARE ARE AVALIABLE OR NOT PLEASE HELP ME TO DO SO
THANKS
PRAVIN

hi helm
Thanks a lot for your suggestion i got the required farmware
thanks
prav

Need a new wireless router with switching

I would like to purchase a new wireless router with 4 port switch. I have an Intel iMac with 2 pc's and have spent hours trying to configure my existing Linksys router to work properly and need to make a change. I have not been able to use iChat with Powerbook users and have had other problems as well and have given up...
The recommended router list on the iChat website does not specifically mention wireless routers with 4 port switching...
Does anyone have any suggestions for a router which is easy to use and configure?
Thanks,
cj

Hi Herpestes,
If you mean which method of opening the ports should you use for those computers it will be the UPnP setting found in the Adminstarion tab
Log on to the Linksys by typing 192.168.1.1 into a web browser
Type admin as User ID and Password.
Go to Administration
Enable UPnP
10:10 PM Wednesday; June 28, 2006

How do you replace a Virgin wireless router with a time capsule?

Hi Folks
i have just bought a brand new 1tb time capsule yesterday and im trying to connect it too my virgin modem and replace the virgin wireless router i already have.....i thought it would be an easy setup of just plugging in the ethernet cable into the time capsule..but this has not worked??..can this be done?? i have restarted all devices too!...i am now clueless!
the the time capsule has backed up my hard drive (mac book pro) with no problems!
kind regards
kathdol

Are you talking about a separate modem and Virgin router, rather than their wretched 'Superhub' (modem and router combined) - the latter is a whole different can of worms.
Assuming the former, you should be able to remove the Virgin router and plug your Time Capsule into the modem: you will need to power down the modem and leave it for a few minutes (to forget the MAC address of the Virgin router), then plug in the TC and power up the modem. Make sure that the TC is set to 'Share a public IP number', not 'Distribute a range of IP numbers' or 'Bridge mode'. (If the interface is the same as the Airport Express it's 'Manual Setup'>'Internet' (in the toolbar)>Internet settings.

How do I connect my HP Laserjet 1102w directly to a Linksys AE3500 wireless router with USB option?

I am trying to connect an HP Laserjet 1102w directly to an HP desktop model a172n with Windows Vista Home Premium OS (32 bit) through a new Linksys AE3500 dual band wireless router which has a USB port for a direct connection. The desktop can see the wireless router but not the printer.
Is there a work around, a printer installer update, or some other solution that enables me to connect the desktop to the printer via the USB connection on the wireless router? I need to have one wireless laptop and one non-wireless desk computer able to use the one printer.
Thanks for any assistance!
Murleen Ray

hi there,
It seems as though this situation will require the Cisco connect software to function properly. Check out this article from the cisco knowledge base. It has the step by step setup specific to your case. Let us know if this helps or if you have already been through these steps.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

I keep losing my wireless connection after periods of inactivity - any solution? I recently installed a new wireless router with improved range.

I recently installed a Netgear Wireless router for improved reception, but now my macbook loses connection through Airport after periods of inactivity. We have another older Macbook in the house, and it never loses connection. I never had this problem with the previous Linksys router, just limited range. Any ideas what is causing this? It's frustrating to have to frequently shout down and re-boot. That so far is the only way I can re-connect.

Adjust the Wireless Settings on your linksys router...
Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave username blank & in password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab on the Setup page- Here Wireless Network mode should be mixed- Provide any non linksys network name ....
Name (SSID) box- Set wireless channel to 11- And wireless SSID broadcast should be Enabled and then click on "Save Settings" >>
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WPA, For Encryption, select AES...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your
network key whenever you connect to your wireless network.
Do NOT give this key to anyone.
Click on Advanced Wireless settings>>
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304 Change the RTS Threshold to 2304 >>Click on "Save Settings" ...
Try to look for the Wireless Network on your laptop and attempt to connect...

Wireless router with 3g

Hi,
We are planning to prepare a demo lab for customer demonstration so that we will carry all these demo lab to customer premises and connect to our UC lab and will show the demo UC features. Equipments would be included in the demo are below:
1. Two video IP Phones
2. Two iPads and Two iPhones
3. One wireless Router (at least two PoE LAN port) with 3g connection.
Plan is, Router will be connected to internet through 3g connecton and configure VPN to our LAB to connect with UC solution. iPad and iPhone will be connected demo voice gateway through wireless and two video phones will be connected through PoE LAN port.
Need suggestion to select the Wireless Router, which model is appropiate for this setup.
Best Regards,
Muzammel

Any Cisco ISR Router will do, provided you equip it with a 3G WIC such as :
http://www.cisco.com/en/US/products/ps7272/
Performances will depend on the quality of the mobile carrier.
Make sure the Router IOS does support VPN connection.
Frank

Have a static IP for internet access - how do I replace my Linksys wireless router with Time Capsule?

Have 5 macs on an ethernet network - some wired and some wireless to a Linksys router. My provider uses static IP and DSL for internet access. I am replacing an existing Linksys router with the Time Capsule. The Static IP settings I have are IP address, Gateway, Mask, primary DNS and secondary DNS. The Airport Utility is not as straight forward as the Linksys setup. There is not a place to list gateway. Consequently I am unable to connect to the internet and am back on the Linksys router until I get this resolved. Any suggestions would be much appreciated !

You enter the static public IP address info on the TCP/IP tab within the Airport Utility. For a static address, use Configure IPv4 = Manually. You use the Router field for the Gateway address.

Wireless Router with USB + External Hard Drive = Time Capsule?

So I bought a TP-Link WR710N wireless router http://www.tp-link.com/en/products/details/?model=TL-WR710N which seems to support external storage in its USB port. I tried with various storage media and it kinda works. The bad thing is that it only sees NTFS drives. I tried an external hard drive formated for Windows and a USB stick, also formated for Windows and it discovered them. But when I tried my external hard drive which is formatted as Mac OS Extended (Journaled), which I was using for Time Machine, it couldn't see it. Neither the TP-Link software, nor the Time Machine software.
Is there any way I could use this router with this hard drive for wireless backing up with Time Machine NOT buying extra equipment (NAS, AirPort Extreme or Time Capsule) ?
Thanks.

m3adi3c wrote:
Is there any way I could use this router with this hard drive for wireless backing up with Time Machine NOT buying extra equipment (NAS, AirPort Extreme or Time Capsule) ?
Thanks.
No
Take it back and get a Time Capsule or keep it and buy a regular external drive and connect it to the Mac directly.

I have a new ipad2, also an ipad1, with a gateway laptop. I have wireless router with windstream. Able to access my wireless connection on ipad1 and laptop, but can't on ipad2. Will say connected, but get message saying not connected to internet on Safari

I got an ipad 2 today. Already have an ipad 1 and gateway laptop. Have wireless internet with windstream. I have internet connection on ipad 1 and laptop, but can't connect to internet on ipad2. It says i'm connected, but when accessing Safari, it says not connected to internet. Tried unplugging router and resetting already, still not working. Thanks for the help.

Thank you for your response.
I did try turning off the firewall, and reducing all the security levels to a minimum (under Control Panel>Internet Options). Also, I'm using a direct cable from my m/c to the Airport Extreme. But nothing helps. Due to the usage pattern in my family, using the MacBook for configuring the network is not optimal, hence my struggle to do it on my Windows desktop. But if that is the only way to go I suppose I'll have to.
Subsequent to posting my query, I discovered that Apple had not singled me out, and many others with a Win OS face this problem, too. I would have thought Apple would do a proper job of testing before putting up the Windows version of Airport Utlity on their site.
But thanks again. Much appreciate it.

Use wireless router with existing network and switch?

I have an existing network using a T1 into a switch; all the computers and the server are connected to the switch. Some distance away, via ethernet cable to the switch, I would like to connect a wireless router, one computer wired to that router, and other computers connect via wireless. Our server provides DHCP. Is this possible? How best to do it? Which Linksys router would be best for the purpose? Thanks for the help!

The "correct" device to use would be a wireless access point like the Linksys WAPs and not a WRT router. WRT routers are supposed to connect to the internet on its own.
You can set up a WRT router as simple access point. see here for the setup.
The best router is the one which best suits your needs. All wireless routers and access point provide wireless access. It depends on what you want (802.11n, 11b, 11g, range, speed, etc.). The newer routers are better from the specifications but usually also have more firmware bugs. But that's pretty much all one can say based on your generic requirements.

Error message when connect to wireless router with wifi enabled phone

Wireless router model WRT54G Ver.2
i would like to seek help on this.
I have been using a wirreless router to access the internet with my computer and it has been working fine. recently i got a handphone with wifi capability (nokia 5800). I managed to connect the phone to connect to the wireless router (it says so in the phone status). but when i tried to open the browser in the phone i got an error message "No Gateway Reply".
Can anyone help me to troubleshoot?
I enable WEP for security.
another thing is, i tried to use the phone to connect to another wireless router at the cafe, it worked well.
thanks

When you connect your handphone to your wireless network, whats the IP address you are getting it on your handphone, if required you can provide a static ip on your handphone i.e IP : 192.168.1.10, Subnet : 255.255.255.0, Default Gateway : 192.168.1.1, DNS1: 4.2.2.2, DNS2 : 4.2.2.1 and after this you can restart your handphone and try to check if you are able to go online or not.

Setup wireless router with tablet

Similar Messages

Maybe you are looking for