Setup WIzard error. Unable to connect to the Router.

All the connections are correct. I am able to connect to IE and FireFox with ethernet and connected my nook via 'Linksys'. I opened using ISP address and set up security. Is there more in the setup that I need to do?
Solved!
Go to Solution.

Hi. Are you still getting that error after you setup everything on the router? Is wired internet working already? Are you replacing an old router? If you still encounter that error, you can download the updated software version for your router. It is best to wire your computer directly to the modem for that and run it from there. You may have to reset the router back to defaults by pressing its reset button down for 15 seconds so that you can start afresh with the setup. I have here a link for you that might help you regarding the software:
Cisco Connect error codes
http://homekb.cisco.com/Cisco2/ukp.aspx?vw=1&docid=8c48ffab84714adb992ca2bf5dd9a529_Cisco_Connect_Er...

Similar Messages

HP Device Toolbox software Error Unable to connect to the printer

Hi guys,
I'm currently in bit of a nightmare with my HP Laserjet 100 color MFP M175nw.
Basically I have upgraded to a new wireless router and since doing this my HP Laser Jet refuses to work / connect to the wireless network.
I have literally tried just about evey thing I can to get it to work, thoroughly through the manual, uninstalled and reinstalled the software about 12 times, tried firewalls on and off, tried security on the router on and off, tried WPS mode, tried manually entering in the IP address into the printer all without luck. You can see my dedicated thread here
http://h30434.www3.hp.com/t5/Printer-Networking-and-Wireless/HP-LaserJet-Pro-100-color-MFP-M175nw-un...
So currently I have the printer connect to the computer via USB and it works, so I decided to try using the HP Device toolbox software to see if it would give me any more options to try and when I run this software I get
Error: Unable to connect to the printer, make sure your printer is properly connected and powered on and then try to open the HP device toolbox again. Arg!!!
My new router is a Billion 7800DXL, my old router which worked in wireless mode was also a Billion 7300g.
Any help would be great really stuck here

Hello tf22raptor.
I see that you're now experiencing an issue getting the Device Tool box to run. I will try and assist with this.
After reviewing this post and the other thread, I have a few things you can try.
1) Run MS Fix it utility to uninstall the software: Fix problems that programs cannot be installed or uninstalled.
(This is to make sure the software is completely removed and conflicts in the registry get resolved)
2)Msconfig: press windows key and R on the keyboard> in run box type "msconfig"> on window select "services tab"> check box next to "hide all MS services> press disable all> go to "startup" tab> press disable all> press apply and ok at the bottom> this should prompt a PC restart.
Please restart.
3) Re-install via USB
4) Try running the device toolbox now
5)If still having issues installing wireless, you may have to contact the router manufacture.
I hope this helps you out. Thanks for posting on the HP Forums.
I worked on behalf of HP.

We are using the Azure server for our web services. Server is generating an error "Unable to connect to the remote server". What is this error means

We are using the Azure server for our web services. Server is generating an error "Unable to connect to the remote server". What is this error means

Hello,
Did you means that you use the Windows Azure Virtual Machine DNS name as the server name in the Reporting Server Web Services URL?
For example:
Report server:http://uebi.cloudapp.net/reportserver
Report manager:http://uebi.cloudapp.net/reports
If you want to connect to Report Manager on the virtual machine from a remote computer, you should create a virtual machine TCP Endpoint and open the port in the virtual machine’s firewall. By default, the report server listens for HTTP requests
on port 80.
Reference:http://msdn.microsoft.com/en-us/library/jj992719.aspx#bkmk_ssrs_connect_2_remote_RM
Regards,
Fanny Liu
Fanny Liu
TechNet Community Support

WRT54G: Unable to connect to the Router!

I have set up my router exactly as told in the setup wizard, but when I get to step 8, I encounter a problem and I get the following error message:
Unable to connect to the Router!
Check that your Router has been connected to the computer, and that your Ethernet adapter is working!
Oddly, my wired internet works just fine through the router, but my wireless doesn't because I can't complete the setup. All the lights that are supposed to be on are on and not blinking or anything.
What do I need to do to fix this?

you can actualy configure the router without using a setup cd.. you can try accessing the router setup page using your working computer that is wired to the router. just go to internet exp. type 192.168.1.1 on the address box.. it will ask for password- just type admin. go to the wireless menu - change the ssid to any name that you want to name your network. try to view wireless networks on your wireless pc and check if you can see the name that you set. connect to it..
you can check if it works.
Piz Brother,
>>>--DARK_TEMPLAR -->

Server cleanup wizard problem - unable to connect to the WSUS Server Database.

I'm trying to run server cleanup wizard.. it starts to run and then after a while it gives me this error:
The WSUS administration console was unable to connect to the WSUS Server Database.
Verify that SQL server is running on the WSUS Server. If the problem persists, try restarting SQL.
System.Data.SqlClient.SqlException -- Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding.
The statement has been terminated.
Source
.Net SqlClient Data Provider
Stack Trace:
   at Microsoft.UpdateServices.Internal.BaseApi.SoapExceptionProcessor.DeserializeAndThrow(SoapException soapException)
   at Microsoft.UpdateServices.Internal.DatabaseAccess.AdminDataAccessProxy.ExecuteSPSearchUpdates(String updateScopeXml, String preferredCulture, ExtendedPublicationState publicationState)
   at Microsoft.UpdateServices.Internal.BaseApi.Update.SearchUpdates(UpdateScope searchScope, ExtendedPublicationState publicationState, UpdateServer updateServer)
   at Microsoft.UpdateServices.Internal.BaseApi.UpdateServer.GetUpdates(UpdateScope searchScope)
   at Microsoft.UpdateServices.UI.AdminApiAccess.UpdateManager.GetUpdates(ExtendedUpdateScope filter)
   at Microsoft.UpdateServices.UI.AdminApiAccess.WsusSynchronizationInfo.InitializeDerivedProperties()
   at Microsoft.UpdateServices.UI.AdminApiAccess.WsusSynchronizationInfo.get_NewUpdatesCount()
   at Microsoft.UpdateServices.UI.SnapIn.Pages.SyncResultsListPage.GetSyncInfoRow(WsusSynchronizationInfo syncInfo)
   at Microsoft.UpdateServices.UI.SnapIn.Pages.SyncResultsListPage.GetListRows()
Thanks

Some questions:
Are there any other databases running on this Std Edition SQL service?
[a] Yes there are, we have Kaspersky enterprise DB, Report Server DB and local application DB.
Are there any other services running on this WSUS Server?
[b] Yes there are, we have Active Directory, Kaspersky enterprise, SQL Server 2005, and WSUS all on the same server.
How many days since your WSUS server was first installed?
[c] It's been about a year now.
What is the physical size of the SUSDB.mdf file?
[d] 9,666,752 KB
What is the hardware configuration of this machine, including disk drives?
[e] Intel Xeon 1.86, 2GB Ram, HD C: 39GB - E: 25.2, running Windows Server 2003 R2 SP2.
How many client systems are you servicing from this WSUS Server?
[f] Around 40.
What products/classifications are you synchronizing.
[g] Windows XP-vista, Windows Server 2003, Office 2003-2007, SQL Server 2005.
Okay, for starters, you have an underpowered/overextended machine running Active Directory, ASP.NET, and a database server, all on a sub 2GHz CPU with 2GB RAM, and not enough disk spindles. The machine has had WSUS running for about a year and is 9GB in size.
There's no doubt in my mind that some of your performance issues are directly related to disk and database fragmentation.
There's also no doubt that some of your performance issues are directly related to memory starvation.
I'd suggest the following long-term fixes:
1. Get a second machine. Make it a dedicated database server. Provision it accordingly to support servicing multiple database applications.
2. Lacking #1, this machine needs more memory. It also needs more disk spindles. At a minimum the databases being serviced should be on a dedicated physical drive; ideally there would be two dedicated drives allocated for supporting database services. The
For the short-term fixes, do this:
1. During after-hours time, if you don't already have one, build a temporary machine that can act as a DC/GC, while you take this machine temporarily offline.
1. Shutdown the Update Services service, SQL Server database engine, and any other services dependent on the SQL Server database engine (Kapersky, and other reporting applications). Disconnect from the network to temporarly eliminate DC traffic. (You could also shutdown the AD services, but disconnecting the network cable is ever-so-much easier.) Defragment ALL drives.
2. Restart ONLY the SQL Server service. Obtain this SQL script to Reindex the WSUS Databases.
3. Restart ONLY the Update Services service. Attempt the Server Cleanup Wizard again. Run it in two passes. Pass 1 performing everything except remove unused updates. Pass 2 running only remove unused updates.
4. After completion of the Server Cleanup Wizard, reconnect the machine to the network and resume all other services.
5. If you're able to complete #3, secure the services of a well-qualified DBA to determine if there are any misconfigurations in your SQL Server setup that would account for why your WSUS database is 9GB in size -- such as improperly configured autogrowth parameters. Based on the products you're updating and only forty clients, 9GB is about 3x the maximum size I would expect to see in a WSUS database. It's possible this is simply caused by excess unused updates, it's possible it's caused by fragmentation, it's probable it was caused by unnecessary autogrowth of the database due to insufficient update maintenance. You'll want a DBA to assist you in shrinking that database after you successfully run the Database Maintenance and Server Cleanup Wizard.
Lawrence Garvin, M.S., MCITP(x2), MCTS(x5), MCP(x7), MCBMSP
Principal/CTO, Onsite Technology Solutions, Houston, Texas
Microsoft MVP - Software Distribution (2005-2009)

Possible workaround for: Launch Debugger Error "Unable to connect to the RDS server"

I do not yet have a reproducible case for this. *Sometimes* ColdFusion Builder throws the "Unable to connect to the RDS server" error, when attempting to start a debug session against a remote server. However, "RDS Dataview" and "RDS Fileview" views correctly list the servers and their related data/file, and testing RDS connection result is "Test connection was successful". The workaround is:
1. Login to the ColdFusion Administrator
2. Navigate to "Debugger Settings" page (beneath "Debugging & Logging")
3. Click on "Stop Debugger Server" -or- "Restart Debugger Server"
4. Restart ColdFusion Application Server
Notes:
a) Step #3 must be done via ColdFusion Administrator, not via ColdFusion Admin API (stopLineDebugger()|restartLineDebugger())
b) Step #4 can be done via ColdFusion Administrator -or- ColdFusion Builder
c) Note that there is a CF9 Release Note for Bug #78488: "When a server having "Windows service option" ENABLED is added as a remote server, then Start-Stop-Restart operation cannot be done on it." However, I've found that "Restarting" a remote server, that is running as a Windows service, is possible in ColdFusion Builder (at least this is so on standalone developer edition). Like Bug #78488 says, I am unable to "Stop|Start" a remote server that is running as a Windows service. I'm just mentioning all of this, due to my suggestion in "b", that CF can also be restarted via ColdFusion Builder.
It is interesting that attempts to stop|restart the debugger server, via CF Admin API, do not resolve the issue. So, it seems that the "Stop Debugger Server" and "Restart Debugger Server" buttons, in CF Admin, are doing more than calling the corresponding CF Admin API methods.
Attached is an image of the error.
Just posting all of this as an FYI, in case it helps anyone.
Thanks!,
-Aaron Neff
(OH.. I'm unable to attach images at this time *DOH!* ..well, I'll try to remember to update this post w/ the image, once I see that attachments are allowed.)
I'll try to describe the error message window:
- It is 494x452 pixels
- Title of the window is "Error occurred while launching the Debugger"
- Body content of the window is as follows:
Unable to connect to the RDS server 'ServerNameHere'
Ensure that the server is currently running and that line debugging and RDS are enabled. You may also need to check your RDS connection settings in Eclipse to ensure that they are correct.
Error Message:
-1:Error connecting to JVM for debugging at localhost:5005. Could not attach to the VM at port 5005. You must specify this debugger port in the JVM settings of your application server, for example: -Xdebug -Xrunjdwp:transport=dt_socket,server=y,suspend=n,address=5005. You will also need to make sure that another debugger is not currently connected to the CF JVM at the same port (5005).
Root cause ->
Connect refused: connect

hi,
I have been facing the same problems while connecting to Oracle Web Conferencing and is getting error message :Unable to connect to the server. The Web COnferencing Console will now close. Please try again later. If the problem persist, contact your system administrator.
Diagnostic report shows failed on the connectivity part
Connectivity
mx-direct Failed
0:00:00.719 Connecting to web331.oracle.com:1025
0:00:00.922 Name resolved to 148.87.108.234
0:00:21.906 connect() failed (0x8007274C)
0:00:21.906 Connection failed (0x8007274C)
Pl help me to fix the problem.
Regards
Gobind Ahuja

Web Service Error : Unable to connect to the remote server

Hi,
I encountered below errors while I run the web service in ERP 2006 system :
Unable to connect to the remote server,
No connection could be made because the traget machine actively refused at xxx.xxx.xxx.xxx:443
Pls kindly advise.
Thanks.
Edward Tso

Hi,
Do you have proxy server , check property added t.o the java proxyparameter .
Also check the log , any fire wall restricting the connection.
Its better, you put error log you get.
Regards
Nagaraju

Unable to connect to the router! (wrt54g v. 2)

I just got a router from a garage sale; it was still in the box and everything.
Well, I tried hooking it up to my modem and computer to get wifi, but I can't get it to work.
This is the setup:
modem -> router -> computer
I can access the internet when the setup is this way, but there's no wifi, and I can't access 192.168.1.1 or set it up using the CD it came with. When I go through the setting up process with the CD, I get this error message that says "Unable to connect to router! Check that the router has been connected to the computer, and that you're ethernet adapter is working."
When I try to go to 192.168.1.1, it says "The connection has timed out." I can't ping it either.
I've also tried resetting it several times, but that doesn't do anything.
Someone please help!

Hi sylentknight and welcome to the forums!
You said that you are able to connect to the internet with this set-up: modem -> router -> computer right? So does that mean that you can ping the router when it is connected directly to your computer? Reason why I'm asking is if it does work, you can try to configure the router for the wireless settings while it is directly connected to the router first then try to go wireless. Please let me know if understood your post correctly.

Unable to connect to the server.. Error Data : API_NOT_INITIALIZED on CUEAC Server Installation

Hi all,
I am trying to install CUEAC Attendant Server on Windows Server 2008 R2, tried several times. First, it got stuck on the Databahse Wizard. After three reinstalls, it still got stuck but somehow built the configure database named CFGATT and then started installing TSP. Finally, the setup has been finished and I went to the WebAdmin page. After I entered the login information, it gave an error : "
Unable to connect to the server.. Error Data : API_NOT_INITIALIZED"
I searched through the forum and found this topic :
https://supportforums.cisco.com/message/1215763
Here I found that there's a bug and I tried to do the fix myself as instructed :
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCte44454
However, it changed nothing, looking forward to your responses.
Regards,
Fikri

Fikri,
It is not working as this is not a supported environment, the current release is not supported on Windows Server 2008 R2.
The next release (April 2013) will support that version of Windows Server.

Community Publishing-"Unable to connect to the CPS server" Error

I am trying to connect to Community publishing.
I download the Community Publishing Air app, but when I put in my username/password,
I get this error "Unable to connect to the CPS server. Please make sure your firewall settings allow access to this url:
http://cps.corp.adobe.com/nioamfpoll".
I have updated Air, but got the same behavior.
I am running osx (10.6.6) on a 8 core Xeon.
Any suggestions?
Thanks
Clay

Hi Clay,
Do you have a firewall, or are you behind a corporate firewall that blocks certain ports on your machine?
What do you see when you visit this URL?
http://cps.corp.adobe.com
How about the following URL?
https://cps.adobe.com/nioamfpoll
Thanks,
Puny Sen

Nokia Messaging Email - Unable to connect to the s...

Every time I try to add my corporate email to nokia messaging I receive this error:
Unable to connect to the server. Please try again later.
I confirm that the email address and the password are 100% correct. I confirm my phone setup and internet work perfectly becasue I successfully added another 3 email acounts.
ANYBODY - PLEASE HELP!

I decided to revisit this topic out of curiosity and managed to get it working! I solved it with a variation of post #9 by Tbosh.
As you repeat his step #1, take note of the subdomain of the URL, in my case it began with http://netac3.vie....
When you get to the step where he mentions
https://netac5.vie.hosting.nokia.com/account/addEmailMoreInfoNoCorpSuppo...
replace the subdomain with yours, so in my case the link became
https://netac3.vie.hosting.nokia.com/account/addEmailMoreInfoNoCorpSuppo...
I suggest you perform the process on your desktop, it's easier than on your mobile device.
- Tom
Message Edited by tomfoley on 15-Dec-2009 11:48 AM

Unable to connect to the CDDB using iTunes 10.6.1.

When I put my CD in and try to get the track names, I get this error:
Unable to connect to the CDDB server. the network cannot be reached.
The internet is fine, I checked the firewall and I unistalled/ reinstalled iTunes, but this error keeps popping up.
I was able to connect late week and retrieve track names, but yesterday and today the same error. Any suggestions?

I have same problem but I am on a PC. Everytime I try to get track names I get the CDDB server error. I have an interenet connection and can upgrade itunes (which seems to me that the application knows I have an internet connection) but I continue to have problems with track names and it seems artwork as well.

Unable to connect to the Exchange server using HTTP/HTTPS protocol.

hi,
i try to connect microsoft exchange server, but it give me
error
Unable to connect to the Exchange server using HTTP/HTTPS
protocol.
my code is pasted below............

<cfparam name="user1" default="uHRH">
<cfparam name="user2" default="uHRH">
<cfparam name="password" default="uHRH">
<cfparam name="exchangeServerIP" default="192.168.0.1">
<cftry>

<cfexchangeConnection
action="open"
username ="#user1#"
password="#password#"
server="#exchangeServerIP#"

connection="conn1">
<cfoutput>Connection to exchange server
"#exchangeServerIP#" established</cfoutput>

<CFExchangeConnection
action="close"
connection="conn1">
<cfoutput>Connection to exchange server
"#exchangeServerIP#" terminated</cfoutput>

<cfcatch type="any">
<cfoutput>#cfcatch.message#</cfoutput>
</cfcatch>
</cftry>
if any one know how to solve this error?

Hi,
The "<cfexchangeConnection>" tag supports both "HTTP"
and "HTTPS" connection.. So Please make sure the username has the
"Outlook Web Access".
Also try removing the 
comment which you placed inside the "<cfexchangeConnection>"
tag.

Unable to connect to the informatica repository on oracle database 11g

hi all,
i have installed OBI Apps 7.9.6.0 with informatica 8.6.0 and no hotfix.
Now the problem is , when i create a repository service i get the error
" The service did not start due to the following error: *Unable to connect to the repository Oracle_BI_DW_Base on database* . " here Oracle_BI_DW_Base is also the name of my .rep repository that came with OBI APPS installation.
i have oracle database 11g installed and also created respective user for repository of informatica.
what should i do in this case??
plz help

Good Morning.
I had the same problem and I had the same IE 6, the problem was the translation between the IE6 from http and https, to solve it you just need to open your url typing
https:url:port, do no forget to put the s after the http, with this my problem was solved.
best regards.
Digudi - São Paulo - Brazil
Edited by: user12267194 on 24/11/2009 05:37
Edited by: user12267194 on 24/11/2009 05:38
Edited by: user12267194 on 24/11/2009 05:38

Unable to connect to the Essbase server from Admin console

Hi,
I have installed Essbase Server 9.3, Client 9.3 and Administration Server 9.3 in my laptop.
The Essbase server is working fine. I am able to see all the sample applications from Excel add in. (This mean client is also working fine).
But, the problem is when i try to connect to the Essbase server, its not allowing me by producing an error:
"Unable to connect to the Essbase server please check the user name & password"
username: admin
password; password.
i tried several times...but its not working.
Please advise me.
FYI, The admin server service is started already.

Hi Subrahmanyam,
Here , there are 2 things
1. Check, your essbase server is up and running ,and your admin service is up. Now , when you open the 'essbase admin console ' , provide user name and password as
admin
password
2. After you are connected to the console i.e admin console .
You see
enterprise view -> essbase analytic server -> under this , you might see your host name ( i.e of your laptop).
This host is your essbase server , and if you want to connect to it .Provide 'username' and 'password' ,which you have give after your essbase installation
So, conclusively, here we are dealing with 2 different sets of 'username' and 'passwords'
In step 1-> to connect to console , use 'admin' 'password'
In step 2-> to connect ot essbase server, use the credentials wchih you had given after installation of essbase server
Hope this clarifies you, as this is a lil confusion to many
Sandeep Reddy Enti
HCC
http://analytiks.blogspot.com

Setup WIzard error. Unable to connect to the Router.

Similar Messages

Maybe you are looking for