SF 200-24P - Rebooting Problem??

Hi All
I have a SF 200-24P Cisco switch that seems to be rebooting constantly, When i connect it to mains power it seems to go through a startup cycle, in this order - i have tried this with no network devices attached and the same thing happens
1. Fan starts - continously runs
2. Very quick flash of all RJ45 ports.
3. After about 30 seconds, any network devices connected have an acticity light
4. After about another 45 seconds, all ports light up including the activity and POE orange LEDs for about 5- 10 seconds then go off.
5. About 10 seconds later the ports all light up again and stay on for about 5 seconds.
6. All ports go off and the cycle keeps repeating continously.
I have tried pinging the switch without success.
I have also tried disconnecting all devices from each port with no success.
At no time does the system LED on the left light up.
I have tried resetting to factory default with reset pot on the left side.
This is a brand new shipped switch from our cisco supplier, could it be DOA?
If required i can make a video of this sequence so you can ascertain what the problem could be.
Thanks in advance

Hi Luke,
Yep, if you have a concern about DOA, it could be easier to have a chat with your disti partner . If it is DOA they should quickly replace that product.
You also have the option of ringing the good folk at Small Business Support Center (SBSC) they also should diagnose any error and arrange a RMA.
With the 300 series product there is a option to interupt the startup and upgrade the software incase it is just a flash issue or software corruption. With the 200 series you do not have that option. If the product was stable for a couple of minutes, i would have tried a software upgrade. But working in conjuction with either Disti or SBSC you will come to a satisfactory resolution. Thank you for your purchase and sorry that this first experience isn't what we would have hoped for.
here is the contact details for SBSC;
http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
Regards Dave

Similar Messages

SF 200-24P does not see the MGBSX1

I have a SF 200-24P and plugged in a MGBSX1. I am logged into the web interface and see that nowhere does the switch acknoledge the mini-GBIC. I can see that the GBIC is powered on. If I plug the fiber in, the transceiver on the other end shows a link. In fact, the transceiver's loop-back test reports all is well. The switch however will not pass network traffic! I tried both mini-GBIC ports. I tried another brand new mini-GBIC from SMC, still no joy. While I do not have another SF 200-24P to try out, I do have a SG 102-24 and plugged the MGBSX1 into it. I'm still not transmitting data, although I do not know of a way to test it other than to plug it in and see if data transmits.
Is there something 'extra' I'm supposed to do in the web interface to get the swtich to 'see' the mini-GBIC? I'm to the point of returning the entire setup and just use a standalone transceiver on both ends. Help?

Hi Jerry,
The Sx200/300 series only show the SFP module in the diagnostics when there is an active link, otherwise it does not show any data. When the link is connected you should see them there. Verify the settings in the SF 200-24P under Administration - Diagnostics - Optical Module Status.
As far as the "not passing any traffic" problem is concerned. Are the ports that you are connecting in the same VLAN ? If they are not, that could be a reason why there's no traffic passing. Also verify STP settings, you might have a port blocked by STP if you have redundant links (I guess that is not the case but I can't see from here of course )
Hope this helps,
Best regards,
Nico Muselle
Sr. Network Engineer - CCNA

HTC Incredible Reboot Problem - Must All Be In My Mind

Took my malfunctioning HTC Incredible to V-Experience Store for return. It had previously been declared DOA by Verizon Customer Service and identified as part of a bad batch of HTC I's on the market.....
Store Rep tried his hardest to (1) tell me that my malfunction / constant rebooting is all due to the apps I downloaded from the Market (2) the Verizon Customer Service reps don't really know what they are talking about and are too quick to declare a phone DOA (3) there are no bad Incredibles out there - just bad apps and users that don't manage them correctly.
Wow! Never thought that the 5-8 reboots a day which then locks out my touch screen was ultimately my fault. Also didn't realize that the HTC Incredible has no reboot problem that couldn't be solved by resetting it and (based on the Rep's logic), never loading another app on the phone.
A couple of points - Verizon needs to figure out the message regarding the well documented HTC I reboot problem and stay on it. Second - Every time I step into a Verizon Experience store my opinion of Verizon drops.

I hear you man I am on my FOURTH Incredible. The onyl positive is that I have not had a reboot in 3 days which is a record for me.

Envy phoenix 810-209 rebooting problem

I've got a rebooting problem.
everytime unplug my computer and plug in,turn it on,then exactly 10 minuites after,my computer has rebooting automatically once.
and i keep using,then no more rebooting happened.
But i turn it off,unplug it,plug in,turn it on,then it happen again exactly 10 minuite after.
Please help me.....

Hi,
That is a tough one to diagnose.
Do you have your PC set to display bluescreen error messages?
Open Control Panel, System, Advanced System Settings.
Open Startup and Recovery.
Uncheck Automatically Restart.
Click OK.
You should be able to see any error codes when this happens again if the computer is blue screening.
That should not happen under any circumstance. But if I am following what is happening, and your PC only does this after you turn it off and remove/restore AC current, why are you repeating this action?
Does your PC work correctly, including rebooting and cold boots, if you don't unplug from the household power supply?
Jaco
Errare humanum est.

9810 rebooting problem

Blackberry 8910 kept on rebooting after i completed the update for app world , anyone have a solution to this ?

It has to do with the software. If you're getting that message, then you were able to connect to BlackBerry Desktop Software? If so, this is very good.
If you connected to BDS, click Device at the top of the software then Update. You'll be told your phone is already up to date, which you already stated, so then you'll click View Other Versions and click the version with Currently Installed beside it. This will reload the OS that is currently on your phone and that should smooth out the rebooting problem.
Give it a try and post back with your results.
- If my response has helped you, please click "Options" beside my post and mark it as solved. Clicking the "thumbs up" icon near the bottom of my response would also be appreciated.

SNMP on SF-200 24P

Hi, I need to SNMP on Cisco Smart switch SF-200 24p. I cannot find any option on administration to turn snmp service on. Thanks in advice

Hi Roman, this device does not support SNMP. The SX200E model does.
-Tom
Please mark answered for helpful posts

I m having ipad 4 and after upgrading to ios7 I m facing continuously rebooting problem while switching between apps can any buddy help or facing same problem

I m having ipad 4 and after upgrading to ios7 I m facing continuously rebooting problem while switching between apps can any buddy help or facing same problem

Make sure you have the Latest Version of iTunes (v11) Installed on your computer
iTunes free download from www.itunes.com/download
1) Connect to iTunes on the computer you usually Sync with and Restore
http://support.apple.com/kb/HT1414
2) If necessary Place the Device into Recovery mode...
http://support.apple.com/kb/ht4097
Note on Recovery Mode.
You may need to try this More than Once...
Be sure to Follow ALL the Steps...
Once you have Recovered your Device...
Re-Sync your Content or Restore from the most Recent Backup...
Restore from Backup > http://support.apple.com/kb/ht1766
Note:
Also consider Deleting any Apps you have Purchased / Downloaded but you now never use..

WinXP reboot problem

Hey... when I've installed Windows XP and choose to run it in the os meny, the computer just reboots. I've tried different versions of XP still same problem. Safe mode or command prompt doesn't work either.
The thing is, I have tried to install XP many times now and I've had different error messages but I have always been able to boot XP. Now, without a reason, the computer just reboots! Very strange.

Hardware:
Athlon 64 3000+
MSI K8T NEO-FIS2R
TwinMOS PC3200 DDR-DIMM 512 MB m/Winbond (400 MHz)
Maxtor DiamondMax Plus 9 160GB S-ATA - S-ATA/150 8MB cache
PowerColor Radeon 9660 256 MB DDR
CNet PCI Fast Ethernet Adapter (didn't know the motherboard had integrated network card :s)
I'm pretty sure it's my HD that messes up the system.
Drivers:
VIA Serial ATA RAID Controller
VIA ATA/ATAPI Host Controller
Promise FastTrak 376/378 (tm) Controller
Promise SATA-150 TX Series (tm) Controller
Okey... first I had a problem with a bluescreen when trying to install XP. This was fixed by disabling the external cache and shadowing in BIOS. I'm running ME as my primary and active partition, having XP to test on the other partition as logical. Tried to set it to active but the meny where you would choose OS didn't appear. But I'm still saying that I've been able to run XP before on that partition...
1. I started with loading all the drivers with F6. Then when the installation run there were 2 pop-up error messages about something that the VIA SATA drivers didn't support XP... not sure what it stood but I clicked continue. So when I run XP and installed the drivers and tried to update with Windows Update, a message appeared on the screen telling me to shut down all work because the computer is going to restart in 60 seconds. I guess it has something to do with the error messages earlier when I installed. So the message kept coming up every time I booted up XP and there was no way of canceling it. I realised I shouldn't load both drivers (stupid me), I thought both were needed to get rid of the "can't find HD screen", but then I read on this forum that you should load either VIA or Promise...
2. I tried to load the VIA drivers, but then a bluescreen appeared so the VIA drivers were not an option.
3. Then I tried the Promise drivers, and it worked. No error messages during installation either. But then after the installation, all of a sudden, when I choosed to boot XP, the computer just rebooted!
4. I tried to install another time loading all the drivers. Now, the error messages didn't appear (they should had!) BUT the computer reboots when I choose XP... and now I can't even get XP to boot I don't know what the h*ll happened!
I'm sure if I could get rid of the reboot problem I could try install Promise drivers again and check if it would work correctly. Running BIOS 1.20 update. And I have tried to get XP to work in 2 weeks now and reinstalled XP over and over again, deleeting the partition and then creating new NTFS with quickformat. I'm getting tired of this as my ME partition can't run any games because the latest graphic card drivers doesn't support ME... If I just had choosen to have the OS installed (like an 120$ extra) when I ordered the computer I wouldn't have all those problems... but then I know it is POSSIBLE to get XP to work or else they wouldn't have the installation option when ordering!!
This is as much info as I can give you... hope it helps.

Reboot problem with MSI K8N Neo2 Platinum and 250 GB SATA HDD

I'm having a "reboot" problem with my MSI K8N Neo2 Platinum. After turning my system on it will run without any problems, until I reboot. After a reboot it will always hang after the initial windows-bootscreen. The HDD-light will remain on. If, instead of going into Windows XP SP2, I try to enter the BIOS after a reboot (DEL) the system will also hang (blank screen with blinking cursor).
It started doing this after I installed the Maxtor 250 GB SATA disk. Before, I didn't have problems rebooting. If I disconnect the Maxtor drive I can reboot and enter BIOS and Windows each and every time. Reconnecting the Maxtor 250 GB SATA drive will return the reboot problem. I always have to use the power swith to get a working system again. It's not enough to do a hard reset (this has the same effect as rebooting).
Here are the details of my system:
MSI K8N Neo2 Platinum (BIOS 1.B)
Athlon 64 3200+ (Winchester, 2 Ghz, 512 KB cache, stepping DH-D0)
2 x Kingston KVR400X64C25/512, 512 MB, DDR, PC3200 (2,5-3-3-8 T1)
Asus Radeon AX800 Pro (256 MB)
PSU Antec Sonata 380W
HDD Maxtor 80Gb ATA (6Y080P0, Pri Master)
HDD Seagate 250Gb SATA (ST3200822AS)
HDD Maxtor 250Gb SATA (6V250F0 - jumpered in SATA150 mode, the mobo wouldn't work with the drive in SATA300-mode)
Aopen COM5232/AAH Pro CD-Writer ATA (Sec Master)
BenQ DW1640 DVD-Writer ATA (Sec Slave)
P.S. The NVidia IDE-drivers are NOT installed. System is not overclocked.

Thank you for all the replies. Upgrading to the latest Nvidia IDE-drivers did not fix my problem. Moving to other SATA-ports did not help either. Upgrading the mobo's BIOS is not really an option (I'm using one version before the most recent and there isn't anything in the fixlist of the latest BIOS).
Now I've contacted Maxtor for (hopefully) a new firmware.
Quote from: rogueUK on 31-July-06, 16:55:42
insego please use the SEARCH BUTTON
I did use the search function to find other people with similar problems. The reason I started a topic of my own was because of the text you get while joining:
Quote
Do not hijack another persons topic. If you have a similar problem, start your own thread anyway.
Maybe in retrospect I should first have tried the solutions in other topics.

KT4 Ultra crashing/rebooting problems

Hi all, I've been having computer crashing/rebooting problems when I play 3d games since I got this board. It can happen between 1-40 minutes during a game session and when the computer crashes, the screen would garble up and reboot along with the garbled screen until I cold boot it. I thought it was a heat problem at first but the cpu heat displays at between 34C-39C. Also, when I tried switching out the video card with an older one, the computer works fine during gameplay, and my newer video card ran fine on a friend's computer. Does anyone know of a way to fix this?
System specs are:
Motherboard: MSI KT4 Ultra
CPU: AMD AthlonXP 2400
Power: 300watt
Ram: PC 2700 333mhz DDR 256MB
Video: Gainward Geforce4 Ti4200 Power Pack Plus! Ultra 650 64MB
Sound: Onboard
Thanks

by the sound of it try a bigger psu,antec enermax over 400 watts
make sure fan on cards not loose

Reboot problem when OC the 975X Power Up

I don't want to break any OC record, only want to reach 3 Ghz, but without rebooting problems. Is there a BIOS version that fixed this problem ???. I am currently using the latest (7.3A), and despite now I can set the memory in 1:1 mode (with 7.2 I can't), when I set the FSB to 333 the reboot problem arise. In fact the reboot problem occurs when I set the FSB higher than 310-315 mhz. At 3 Ghz the board is rock solid and run all test, and even the memory at 667 mhz perform equal than 777 mhz (310 * 2 * 1.25). I have to note that the voltages are all stock, and C1E and speedstep are enabled (at 2.8 Ghz works great), do you have any suggestion with this items ??

Quote from: DragonFury on 06-January-07, 22:50:44
memory compatability . i tried 3 different sets of memory ranging from 533 - 800 mhz ( what the board supports ) the samsung 533 5,5,5,15 reboot issues , Ocz 667 5,5,5,15 no reboot issues up to 400 fsb ( its when i break 400 + is when i need to safe mode the bios ) but this is memory getting pushed to hard . and crucial 800 4,4,4,12 reboot issue but the mb remembers my fsb beyond 400 + fsb ( no safe moding the bios on a shut down ) but because of the compatability issue with the crucial i cant break 400 fsb because it wont hold it . the ocz i can do 430 easily . again here we are . is it mb manu , chip set manu , or mem ? me i am goin towards Memory manufacturers because it is there job to make sure there chips work on multiple platforms and keep up with the times . the only thing we can do too help is contact the memory manufacturers tell them our problems rma our current memory and hope they listen to us .... again ITS NOT MSI fault that memory wasnt cut for a peticular chipset they use .
After reading at many forums it seems to me that the memory problems with 975x/965 chipsets are widespread across all motherboard makers. I don't know if the AMD platform is having many problems with high perfomance DDR2 memory, but at the intel side is a nightmare, and I believe is worst with the 975x than 965.
What model is your OCZ memory ??, Value Pro or Gold ??, if Value Pro, has the copper heatspreader or XTC heatspreader ?? (as mine and not even OCZ support can identify...). I am very curious because with it you don't have the reboot problem, and I do have >:(

Multiple cold dtart reboot problem may be linked to Audio drivers!

All-
I received my RMAed board (975x PUE) back 2 weeks ago as there was a problem with my board. Re-installed everything...after afinally figuring out that no other drives but the SATA raid volume need to be in for install or raid volume will not be C: Everything was working fine until I loaded my Audigy Gamer sound card drivers, then windows could not start-up normally. I ripped out the card and restored windows to before the indtall. Everything back to working. So then I decided to install the on-board audio driver and bango! Lot's of cold boot and reboot problems. It usually takes 2-3 tried before windows will come up properly. I have downloaded the latest drivers for both MSI and Realtek...problem still remains.
Any ideas?

I have not flashed the bios and it is the on-board sound! Any idea why cold boot and re-start take multiple tries?
Mark

MDT 2013 Windows 8.1 application install with reboot problem

Hello!
I have a problem with an application install on Windows 8.1. I'm trying to install two applications and have activated "Reboot the computer after installting this application" for the first application. After rebooting the deployment window does
not show up agagin. BDD.log shows, that the deployment starts after the reboot but seems to hang, before the UI shows.
I tried to install this two applications under Windows 7, which works without any problems.
Here is the BDD.log for the failed deployment: http://pastebin.com/PbUH1LUq
Can anyone confirm this problem with MDT 2013 and Windows 8.1? Any ideas how to fix this?
Additional information: Further testing showed, that this problem just occurs, if the application install gets started separately after deploying the OS. If the applications are installed in one deployment together with the OS, everything works fine.

I did the same install on Windows 7, which worked without any problems. Here is the log file: http://pastebin.com/Qgn2PzyC
To make it clear:
If I run a Lite Touch Install task sequence to install Windows 8.1 and install the two applications within this LTI, everything works fine. The computer reboots after installing the first application and the deployment goes on and finishes successfully after
the reboot.
If I first install Windows 7 or Windows 8.1 via LTI and then (after LTI successfully finished) start a separate application install (using a custom task sequence with only one "Install Application" task in it), everything works fine with Windows
7 (installation continues and finishes after the reboot) but fails with Windows 8.1.
In Windows 8.1 the computer reboots after installing the first application, but after rebooting, the installation does not start again.
Keith, as you said, my environment is corrupted, I created an new fresh deployment share, just added the two test applications and the custom task sequence and tried again. Same result, Windows 7 works fine, Windows 8.1 fails by not starting the installation
after the reboot.

Running in Safe Mode - are there any implications. ( a sub section of Rebooting problem continued...)

As with others I have become frustarted by my 9720 rebooting at random sometimes mid call and often at annoying times. I often have to take out the battery too, otherwise it will not restart. I have wiped, rebooted and even tried the 4hr 15 min trick all to no avail.
I am now running in permanent safe mode - the blackberry works fine and I hope I may have found a solution. Nobody seems 100% sure what the problem is caused by, if I have found a cure I'll be pleased, if however there are issues with running in Safe Mode I would be pleased to know.
I don't want toi change phones but the last few days have been very annoying.
Rogero

Safe Mode is not intended to be an "answer"...rather, it is a diagnostic tool to try and root out the cause of issues. It's sole intended purpose is to try and determine if any auto-running add-on or 3rd party apps might be causal to a situation, by suppressing the auto-run at boot up of those items. But, it is not intended to be part of any "normal operation" of the device.
If the results of Safe Mode are that the behavior continues, then other diagnostic steps must be conducted to try and determine the proper course of action. Quite often, there never can be any true diagnosis...but, rather, attempting a series of different remedies until the behavior is cured. For example, if OS corruption is the root cause, it can't really be diagnosed (especially at an internet distance)...rather, reloading the OS might cure the corruption and re-establish good operations.
But, reloading the OS might also cure other causes, so truly knowing exactly what the root cause is quite often impossible. And, if the issue is hardware (as with your suspicion of the battery), then no amount of OS or software "fixes" can truly be a remedy at all.
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Asha 200 Software Update Problem

I use an Asha 200 cellphone with software version being v10.58. At some times, I tried updating the software to the latest version using the Device Update Command in my phone, but got a message that "Update not allowed; contact service provider". At other times, I get a message "No new software available". What should I do?

Software updates vary by region/product code/network locked or unlocked status. It may be possible that the update has not yet been approved from the operator.
Please mark the post as solution if it solves your problem.
Current Device - Nokia Lumia 1020/920

SF 200-24P - Rebooting Problem??

Similar Messages

Maybe you are looking for