SF 200E-24P not upgrading firmware

Help!
I have just received a Cisco SF 200E-24P switch and need to upgrade the firmware. The current version is 1.0.0.12 an need to load the latest (or at least 1.1) to get CDP etc. However when I use the upgrade option in the switch I get an error of..
Firmware Image download through HTTP failed. Wrong File Type
I have tried 3 different versions of the firmware and get the same error message each time.
Can anyone help?
Regards
Simon

Hello Simon,
To verify, you are trying to load a .ros file? Are you using HTTP or TFTP?
Can you factory default the switch then try to upload the 1.1.0.73 (second firmware released)?
Here are all releases;
http://www.cisco.com/cisco/software/release.html?mdfid=283773418&flowid=&softwareid=282463182&os=null&release=1.2.7.76&relind=null&rellifecycle=null&reltype=null
-Tom

Similar Messages

  • E3200 - do not upgrade firmware - storage no longer works and router ping goes to 1000 ms

    I upgraded my firmware because I was having a lot of stability problems with the router.
    Unfortunately it got worse with the firmware upgrade.  There were two symptoms:
    1. the router no longer recognizes the usb attached hard drive / storage
    2. the throughput on the router and ping statistics are terrible unless you unplug the usb attached device (which it can't recognize any more anyway).
    If I were able to roll back the firmware I definitely would.
    I have had around 5 routers over the past 10 years and this is definitely the worst.  Constantly needs restarting, and doesn't work as advertised.

    First of all, you mentioned in your post that you have already upgraded the firmware. So after firmware upgrade did you reset the gateway? It is recommended to reset the gateway once. Steps to reset the router:
    Push the reset button on router for 30 seconds, turn off the router wait for 30 seconds and then power it on. Power light should blink when you perform the reset process.
    After reset, reconfigure the router and then check the connectivity status of the storage..

  • I can not upgrade firmware SRW224g4

    Hello to all,
    I'm trying to upgrade a switch SRW224G4 but without success.
    Model Name
    SRW224G4
    Hardware Version
    00.03.00
    Boot Version
    1.0.0.06
    I send the file via the XModem( SRW2xxG4_FW_1.2.3.0 ).
    Has anyone encountered this problem and managed to solve?
    Thank you.

    The last firmware I know using the 1.0.6 boot code is the 1.2.2a.
    Try this firmware version
    http://software.cisco.com/download/release.html?mdfid=282446894&catid=268438038&softwareid=282463181&release=1.2.2a&relind=AVAILABLE&rellifecycle=&reltype=latest
    -Tom
    Please mark answered for helpful posts

  • Ipad wifi does not connect after upgrading firmware to 3.2.2

    So many posts and replies on connection to wifi with iPad not working... My issue is that everyhing worked perfect a home until i upgraded firmware to latest (3.2.2?). Now it connects and disconnects in second intervals ??!!
    no changes has been made to my router and my two macs connect as before, only iPad does not
    Very frustrating indeed, so any tips on what i should do?
    Cheers in advance

    krannisto wrote:
    So many posts and replies on connection to wifi with iPad not working...
    You may already have seen these suggestions, but in case you haven't:
    _Pad: Troubleshooting Wi-Fi networks and connections_
    ...from here:
    http://www.apple.com/support/ipad/wifi
    And every iPad comes with complimentary telephone technical support for 90 days:
    http://www.apple.com/support/contact/phone_contacts.html
    _iPad Service: Frequently Asked Questions_

  • Freetalk Connect me firmware not upgrading

    My Freetalk connect me firmware is not upgrading. I contacted the ebuy and they asked me various details such as:
    - What is your order number so that we may identify your order? - What color is the light on the device? Is it steady or flashing? - What is the Firmware version you currently have? - What operating system do you have? - What is the location you are connecting it from? - Who is your Internet service provider? DSL or Cable Modem? - What make and model is your modem/router? - Do you have any additional networking devices on your network? (WIFI access points, switches and similar). If so please list them all.
    I gave them all the information and after that they are just not replying back. I am stuck with version 1.0.1 updated on 8/12/2011 without any caller id and lot of static. I want to return it back but don't know what to do. It's definitely not brininging good name for Skype. I would rather prefer vonage who are atleast responsive.
    Can someone please help me?
    The device is connected from more than 2 weeks and I have windows 7 and Mac Lion. I think Skype should intervene in this matter.

    Why doesn't freetalk provide a forced upgrade option so that user can manually update the firmware..The firmware has still not updated. I have provided all the information they eBuy has asked and also unhooked, hooked back the device. Am I still missing anything?

  • After upgrade firmware my iPod does not respond to touch. Help me!

    After upgrade firmware with iTunes my iPod does not respond to touch.
    To be more precise - works, but very, very bad. And around the icons on the display is visible GRAY line of width 1 px.
    Please HELP me! This iPod - the gift for my girl.
    p.s. Maybe this problem arose because I reflash iPod with old cable from the iPhone?

    Thanks all, i solved the problem yourself.
    I helped this one topic: http://discussions.apple.com/thread.jspa?messageID=12641053&#12641053

  • How to upgrade firmware on 7921g wireless phone from 1.0.2 to 1.0.4 via USB

    how to upgrade firmware on 7921g wireless phone from 1.0.2 to 1.0.4 via USB?
    The 7921g is connected via USB to a PC. I am using a browser to access the phone. Documentation says "Click the Phone Upgrade hyperlink under SYSTEM options. " but that option is not present or not visible.

    You can use the Phone Upgrade area on the web page to upgrade firmware files on the phones by using the USB connection or by using the WLAN. To upgrade the phone software, enter the phone software TAR (firmware file name) or use the Browse button to locate the firmware file on the network.
    To display the Phone Upgrade area, access the web page for the phone as described in the Accessing the Configuration Web Page for a Phone section available at http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7921g/5_0_1/english/administration/guide/21adm50.pdf

  • Error on trying to upgrade firmware on BEFW11S4-V2 ?

    Hi.
    I am trying to upgrade the firmware on a BEFW11S4 V2 router. From the Set-up panel, the current firmware is 1.45, dated Feb 28, 2003.
    I backed up the config. and downloaded the latest firmware:
     "BEFW11S4-V2_v1.45.10_fw.bin" from the Linksys website.
    When I go to update the firmware from the router's Set-up .../Help .../Upgrade Firmware,
    after selecting the above file, the update starts and goes for about 5-10 seconds and then fails with the messages:
    ..."Upgrade action is not finish!!
        Upgrade file pattern error"
        Continue
    ...which then returns me to the previous Upgrade Firmware page. Have I missed something??
    Also...
    As background info. (before I forget), I run the router from an XP destop for connection to a DSL ISP and printers connected to the XP machine and for wireless access for a new Win7 Toshiba laptop. Everything seems to work fine so far, but I thought I should get on the latest firmware, eventhough the update would only be a currency update as the release notes don't seem to be an issue from a quick read.

    I think you should reset the router first.
    Connect the computer with the Ethernet cable to the router Ethernet Port.
    Download the latest firmware from the Linksys website.
    Open the setup page of the router.
    Upgrade the firmware using the .bin file which you have downloaded.
    Do not take the backup.
    After successful upgrade,reset and reconfigure the router settings.
    And see if that helps you.

  • AG310:How to upgrade firmware on the Voice part?

    Team, Very simple question, where do I get the latest sipura code to upgrade the voice section of the AG310. Currently running 5.1.5(GWa). Is that the latest, I check the AG310 download section, it only has the router firmware and not the voice component, unless it gets bundled together ? Please help. Thanks.

    You can use the Phone Upgrade area on the web page to upgrade firmware files on the phones by using the USB connection or by using the WLAN. To upgrade the phone software, enter the phone software TAR (firmware file name) or use the Browse button to locate the firmware file on the network.
    To display the Phone Upgrade area, access the web page for the phone as described in the Accessing the Configuration Web Page for a Phone section available at http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7921g/5_0_1/english/administration/guide/21adm50.pdf

  • Firmware 6.05 WLAN problem after upgrade firmware ...

    Please help!
    I just upgraded my firmware to 6.05 and now I cant connect to WLAN
    it was working fine before then i upgraded firmware using OVI suite now no it prompts "WLAN connection failed"
    - I have tried reinstalling firmware numerous times but it didnt solve the issue.

    Is it happening in all WiFi networks you try to connect to ? Have you checked that you do not have any saved WiFi networks stored to the phone after the upgrade ?

  • Can't Upgrade Firmware in Officejet 8000 Wireless Printer

    I've been using this HP 8000 Officejet wirelss with a single usb connection without any issues at all. I set up a two computer wireless network with this printer also being wireless several days ago. No issues at all with the setup. The printer worked fine with test prints, etc. After several hours though I found the printer would loose connection as far as being able to print. It shows up as an avaialble printer, but will not print. A complete powerdown of the printer is necessary to get it working again. This would happen about every 2 to 3 hours. So I tried connecting the printer to the router with an ethernet cable. The problem is not as frequent now, but still happens. The firmware of this printer is 0842BR. There is a firmware upgrade for this particular printer which is supposed to fix issues with network connectivity plus a few other things. I cannot get this firmware upgrade to work with either Windows XP or Windows 7. In XP I get the error message: Firmware Download Utility has encountered a problem and needs to close. In Windows 7 if I just run the file, it extracts to about 47% and then just disappears. If I try to run it in compatibility mode, it says there is a problem with the file.
    Can anyone please help me with getting the firmware upgraded, or does anyone have any suggesting on getting this printer to work reliabily on a network. I havee another Officejet Pro 8000 wireless at home on my home wireless network and it works perfectly. It has different firmware though. Thank you for your help!

    I had similar problems trying to install the firmware from two different PC's running Windows 7-32-bit and Windows 7-64 bit.
    I had an older system with a clean install of Windows XP SP3 that this Printer had never been connected to.
    I downloaded and installed the latest "Basic" Printer Driver as well as the Firmware Upgrade to that PC.
    I powered off the printer and disconnected and reconnected the AC power supply to assure a clean power up state.
    I left the USB cable disconnected until the driver installation directed me to connect it.
    I installed the "Basic" Driver for USB connectivity. I initially had connectvity problems trying to "talk to" the printer but switching to a different USB Cable solved that problem.
    After all the above, the Firmware install went as described in the HP description. 
    The printer now reports the upgraded Firmware Version of "1006BR"
    I hope my experience helps you with your firmware install.

  • E65 can't upgrade firmware!

    Hello again,
    I see that there is a new version of the NSU. I made the update to NSU. I connect the E65 but still can't upgrade firmware.....
    Any news about that?
    The phone's code is 0542346....

    From [email protected] I've got an answer:
    "With regard to your enquiry, I suggest that you update your phone software, which could improve the overall performance of your phone and fix operation issues that you are experiencing with your phone. Nokia Software Updater now supports the Nokia E65. Kindly log on to the following link for Nokia Software Updater:
    http://europe.nokia.com/A4579163
    It is highly recommended that you back up the data on your phone to a computer prior to using Nokia Software Updater as the contents of your phone would be erased. To do so, kindly follow the back up process below:
    1) Download, install and execute the Nokia PC Suite software from the following link: http://europe.nokia.com/A4144905
    2) Establish a compatible connection between your computer and your phone. More information is available at the following link: http://europe.nokia.com/A4423033
    3) Execute the "Backup" application to back up the data."
    Does it work? I wish, but it does NOT!
    Following instruction am trying to update my software:
    NSU is "Preparing update. Identyfing connected phone",
    but then I get message: "Connection error. Sorry, the Nokia Software Updater service is currently unavailable. Please disconnect your device and try again later".
    Without last updates WPA doesn't work... I'm fed up with e65.
    Message Edited by przemyslaw on 19-Jul-2008 11:10 PM

  • Intentionally not upgrading to the new software

    I am intentionally not upgrading to the new software for my ipod touch since I have seen so many people having trouble with it on this website. Can someone tell me what features I am missing.
    Thanks

    What you are referring to is security patches that have to be released regularly by MS. I would take issue with your claim that very few of them cause issues, but to clarify they cause issues with some computers depending on the configuration. And then again some of them caused system wide problems and had to be retracted.
    Firmware updates on iPods/iPhones are much more akin to Service Packs than security updates, but you are talking about different technologies, processors, etc.
    Since buying my 4th Generation iPod I have installed many updates and I have yet to have an issue with any of them. I've also completed updates for people on Windows machines and again had no issues.

  • WRT160NL Why Not Upgraded TwonkyServer to 5.1.6?

    The WRT160NL's latest firmware (1.0.02) has TwonkyServer 4.4.17. The E2100L's latest firmware has TwonkyServer 5.1.6. The E2100L is identical to WRT160NL. Why WRT160NL is not upgraded to TwonkyServer 5.1.6?

     We can not upgrade the E2100L router's firmware on WRT160NL router.
    Either you go for a new router or else we can wait for the new Firmware release for WRT160NL router that can support TwonkyServer 5.1.6.

  • Is it safe to upgrade firmware to 1.2 now?

    i dont see as many posts about the problem anymore, and some people have claimed that they have no problems with the upgrade. and to these people: was there any special way you upgraded? (i.e. restored iPod to factory settings before upgrading, etc..)
    thanks in advance!

    Do NOT upgrade to Firmware 1.2 IF 1)You have an older Video iPod and 2) you want to be able to view videos you downloaded from iTunes via an iTunes 6.x version. It will cause your Video iPod to lock up after just a few seconds.
    IF however, you only plan on watching videos you download off of iTunes 7.x then you will be fine.
    As of now, Firmware 1.2 is STILL not backwards comparable with your downloaded videos fro iTunes 6.x and it is really frustrating.
    To be able to watch those videos you have to remain in the Firmware 1.1x mode.
    I keep waiting for an update to Firmware 1.2 but it hasn't come yet even though it's been over a few weeks now with thse problems.

Maybe you are looking for