SF 300-24P 24-Port 10/100 PoE - Video is not working smoothly

Hi,
We installed SF-300 24 ports that connected to our network and we connected 20 IP cameras to it. In the Giga ports we connected Video Server.
In the same Vlan but on another switch we connected 2 PC's that can monitor all the 20 IP cameras. Everything worked fine until we had electricity outage.
After that break the monitoring working very bad. The video streaming is not working smooth and it is working with some breaks. I reloaded the switch and everything was back to normal. Can someone send me any suggestions how to configure cameras and how to configure the servers on the port switch? Do I need to enable the smartport option?
Thanks,
Reuven

Hi Reuven, If everything was working as expected and then you had a network event such as a power failure where new symptoms arised, I do not believe this is a configuration issue unless you lost configuration settings. Is that the case? The switch lost configuration?
Having power issues has a funny way of making things have problems. One thing you may want to try to do is isolate your problem to every camera. Do all 20 cameras have an issue or just a few? Is there any symptoms if you disconnect the cameras one at a time?
If all 20 cameras have a problem, I'd recommend to make a back up of your switch and then factory reset the unit as it is possible the power issue caused some sort of corruption in the software.
-Tom
Please mark answered for helpful posts

Similar Messages

Trouble with SF 300-24P 24-Port 10/100 PoE

Good day.
I connect to switch Access Point, configure port on switch which vlan work on this port. But after reboot AP my config for this port delete and have other config where vlan 1 untagged, and allow all other vlan. But in my cinfig allow 3vlan: untagged 100, and tagged 113, 999.
How to solve this problem?

hi Igor, you need to save the running config to the start up config, otherwise a reboot will drop any changes made to the switch.
When you make a change to the switch, on the top right of your browser there is a blinking button to save, click this and save the run config to start up.
-Tom
Please mark answered for helpful posts

Need SNMP MIB files For Cisco SF 300-48 48-Port 10/100 Managed Switch

Hi All,
I need SNMP MIB files for Cisco SF 300-48 48-Port 10/100 Managed Switch.
I have gone through cisco site but not able to get it.
Can anyone please provide me.I have stuck with this.
Thanks
Ram

Hi Ram, yes the MIB can be used. The switches are essentially the same in many regards (especially on a software level).
I do not know the OID for bandwidth. If you're looking for a particular OID may be this tool helps you
http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?objectInput=dot1dTpPortTable&translate=Translate&submitValue=SUBMIT&submitClicked=true
-Tom
Please mark answered for helpful posts

My USB port (closest to the screen) is not working? And what is an IR Receiver in my USB port?

Hi everyone,
     I recently found out that my USB port, closest to my screen, is not working. Before I called Apple Care for help, I performed a PRAM and a SMC RESET, which unfortunately did not work. I called Apple Care and they help me troubleshoot simple resets such as, shutdowns and restarts. The representative I spoke with conluded that the physical hardware has an issue and must be brought to the Apple Store for a diagnosis. I called the Apple Store to at least budget the fee for getting a USB port fixed and it's about $300.00. I never dropped my macbook or had any sort tactile encounterment with hard surfaces by dropping or hitting. I don't understand how my macbook pro would be physically damaged. I then thought maybe my software was out of date (right now I am running 10.9 Mavericks) or I forgot to do the minor software updates, but I was at a lost again because my macbook is up-to-date. I searched for further help and found a way to monitor what's plugged into my usb ports. (I read in the apple forums that a girl had nothing in her usb ports, but upon looking at the System Information> Hardware> USB, that the macbook recognizes that there are drives in the ports) I looked at my ports; one is being used by wirless mouse (the port that works) and the other (the port that doesnt work) is being used by an "IR RECEIVER". Now, is the IR Receiver actually using that port and that's why my macbook cannot recognize other devices inserted into that port? Or is the IR RECEIVER suppose to be in that port and that the hardware for that port is simply damaged (which would mean I need $300.00 to get that fixed)? I know this is a lot, but someone help me?
(PORT THAT WORKS)
USB Hi-Speed Bus:
Host Controller Location:          Built-in USB
Host Controller Driver:          AppleUSBEHCI
PCI Device ID:          0x1c2d
PCI Revision ID:          0x0005
PCI Vendor ID:          0x8086
Bus Number:          0xfa
FaceTime HD Camera (Built-in):
Product ID:          0x8509
Vendor ID:          0x05ac (Apple Inc.)
Version:           5.16
Serial Number:          DJHBAJ06VRDH7FL0
Speed:          Up to 480 Mb/sec
Manufacturer:          Apple Inc.
Location ID:          0xfa200000 / 3
Current Available (mA):          500
Current Required (mA):          500
Hub:
Product ID:          0x2513
Vendor ID:          0x0424 (SMSC)
Version:           b.b3
Speed:          Up to 480 Mb/sec
Location ID:          0xfa100000 / 2
Current Available (mA):          500
Current Required (mA):          2
Microsoft® Nano Transceiver v2.0:
Product ID:          0x0745
Vendor ID:          0x045e (Microsoft Corporation)
Version:           6.34
Speed:          Up to 12 Mb/sec
Manufacturer:          Microsoft
Location ID:          0xfa130000 / 6
Current Available (mA):          500
Current Required (mA):          100
Apple Internal Keyboard / Trackpad:
Product ID:          0x0252
Vendor ID:          0x05ac (Apple Inc.)
Version:           1.18
Speed:          Up to 12 Mb/sec
Manufacturer:          Apple Inc.
Location ID:          0xfa120000 / 5
Current Available (mA):          500
Current Required (mA):          40
BRCM2070 Hub:
Product ID:          0x4500
Vendor ID:          0x0a5c (Broadcom Corp.)
Version:           1.00
Speed:          Up to 12 Mb/sec
Manufacturer:          Apple Inc.
Location ID:          0xfa110000 / 4
Current Available (mA):          500
Current Required (mA):          94
Bluetooth USB Host Controller:
Product ID:          0x821a
Vendor ID:          0x05ac (Apple Inc.)
Version:           0.42
Speed:          Up to 12 Mb/sec
Manufacturer:          Apple Inc.
Location ID:          0xfa113000 / 8
Current Available (mA):          500
Current Required (mA):          0
(PORT THAT DOESN'T WORK)
USB Hi-Speed Bus:
Host Controller Location:          Built-in USB
Host Controller Driver:          AppleUSBEHCI
PCI Device ID:          0x1c26
PCI Revision ID:          0x0005
PCI Vendor ID:          0x8086
Bus Number:          0xfd
Hub:
Product ID:          0x2513
Vendor ID:          0x0424 (SMSC)
Version:           b.b3
Speed:          Up to 480 Mb/sec
Location ID:          0xfd100000 / 2
Current Available (mA):          500
Current Required (mA):          2
IR Receiver:
Product ID:          0x8242
Vendor ID:          0x05ac (Apple Inc.)
Version:           0.16
Speed:          Up to 1.5 Mb/sec
Manufacturer:          Apple Computer, Inc.
Location ID:          0xfd110000 / 3
Current Available (mA):          500
Current Required (mA):          100

I can help with the "IR Receiver" part of your question. That's the piece of hardware inside older MacBook Pros (MBPs) that lets them work with the Apple Remote. "IR" is the standard abbreviation for "infrared," the portion of the electromagnetic spectrum used by remotes for many common devices (stereos, cable boxes, Apple TVs, etc.). The remote sends a coded stream of IR pulses; a corresponding receiver in the target device "sees" the infrared light and decodes it. The MBP's internal IR Receiver sends the received signals to the processor via USB through an internal hub.
The most recent MacBook Pros have dropped the IR receiver and no longer work with the Apple Remote.

I am trying to connect my MacBook Pro to my TV with a mini display port to HDMI converter. Its not working. Any suggestions?

I am trying to connect my MacBook Pro to my TV with a mini display port to HDMI converter. Its not working. Any suggestions?

Depends on your model TV. Read your TV user manual. The newer models have "how to hookup" instructions for computer & games.
You can also do a forum search as well as a Google search.

Port Forwarding in WRT54GL Router does not work

When i forward ports in the firware it does not work correctly. I tested it using http://www.yougetsignal.com/tools/open-ports/ and it still said that the port was closed.

Who is your ISP. When you do port forwarding make sure you have entered the IP address of the computer for which you need to enable port forwarding. Under "Security" Tab uncheck "Block Anonymous Internet Request" and click on Save Settings.After this try testing if that port is opened or not.What ports numbers you are trying to open on your router.

Hp laserjet 100 color mfp m175nw not working anymore – MAC OSX YOSEMITE

After installing the YOSEMITE update my hp laserjet 100 color mfp m175nw not printing anymore. Connection is USB. And OSX Drivers are all up-to-dae. Also i heared similar problems with other printers than HP.
Any help? Thanks alot.

Hi @Ankanb ,
I understand that you are having issues since the Apple Security Update was done on the computer, after uninstalling and reinstalling the software, you can't find the printer now. I would be happy to help you.
I have provided some steps to try, to see if we get the printer working again over the network.
Print a Configuration page to see if the printer still has a valid IPv4 address.
Printing a Configuration Report.
If you have a valid IPv4 address for the printer then try and access the Embedded Web Server for the printer.
Type the IP address into your web browser's address bar. (Safari)
Did it load the webpage?
Repair the Disk Permissions on the Mac:
Close all applications.
On the Apple menu bar, click Go, click Applications and then click Utilities.
Double-click Disk Utility.
Highlight your hard drive/partition on the left.
Click Verify and then Repair Disk Permissions.
Restart the computer..
Reset the Printing System:
Note: This will remove all printers in the print and Fax/Scan, any printer removed can be re-added later by clicking the plus (+) symbol.
Click the Apple icon and then click System Preferences.
Click Printers & Scanners.
Right-click (or Ctrl +click) in the left white side panel, then click Reset printing system.
Click OK to confirm the reset.
Type the correct Name and Password.
Click OK to reset the printing system.
Then click the + sign to add the driver, highlight the printer. (you might have to click the drop down to select the printer's name) Then click on the Add button.
If you are having network issues, then add the printer through the IP Protocol.
After clicking the + button, select the IP icon across the top, type in the printer's IP address, select jet direct below and then Apply. (you won't be able to scan but you will be able to print, this way we will know if it is a Multicasting issue, if the Mac sees the printer)
If the Multicasting is turned off on the router, you won't be able to add the printer as a bonjour device.
Test the printer.
How is the printer connected? (Ethernet/Wireless)
If there is anything else I can help you with, just let me know.
Have a nice weekend!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Forwarding port for Counter-strike: Source is not working

With my linksys router (Model WRT54G)I tried forwarding my port for a Counter-Strike: Source server. My friends tried it after I tried forwarding the ports and it did not work. It looks like this: |Application|Start|End--|Protocol|Ip-Adress------|Enabled| |CS1--------|1200-|1200-|Both----|192.168.1.[105]|Check--| |CS2--------|2700-|27015|Both----|192.168.1.[105]|Check--| |CS3--------|27020|27039|Both----|192.168.1.[105]|Check--| I can get on the server but my friends can not. And yes, I did uncheck "Block Anonymous Internet request". Message Edited by Iridium on 08-16-2007 07:37 PM Message Edited by Iridium on 08-16-2007 07:38 PM
Message Edited by Iridium on 08-16-2007 07:38 PM

Is the IP address 192.168.1.105 really the IP address of the server in your LAN?
Moreover, check what kind of modem you have. Follow the instructions here. If the IP address on the status page is a private IP address and the IP address on whatismyipaddress.com is different then your modem does routing too and you have to configure port forwarding there as well.

Port Forwarding on Home Hub 5 not working

Hi,
Is anybody else having problems getting ports to forward on their Home Hub or Home Hub 5?
I am a new BT customer, less than a week infact and BT have been utterly hopeless in getting this resolved. All they do is send me instructions for port forwarding on a homehub which I do not need and tell me that i need to pay for their tech support to investigate it further which is freaking ridiculous considering port forwarding is an essential part of any router and this router is brand new, less than a week old. (Do BMW sell you a car and then refuse to take responsibility for a broken engine?)
My other option is buying an ADSL 802.11ac router for £150 which out of principle, i dont think i should have to do. One of the reasons i came to BT in the first place was because the homehub is supposed to be one of the best free provider supplied routers around.
Please only reply to this if you know what you are talking about or have experienced this same issue yourselves. I reiterate that I have not missed any configuration steps on my part and this is a case of the homehub simply not working as it is designed.
Scenario:
I like to have remote desktop access to my home computer from external networks. I do not use 3rd party software such as 'log me in' or 'team viewer', I like to use Microsoft Remote desktop and had been doing so for years with my Sky broadband until last week.
I have dynamic DNS running on my machine which updates my constantly changing external IP to the dns server so dont worry about that, thats all good.
I have correctly set up the forwarding of TCP 3389 to the static I.P of my home desktop on the homehub (and rebooted and or factory reset several times)
Result:
Nothing. The homehub displays as though it has forwarded the ports yet i am still unable to remote in from an external network. The port shows as closed when i run a port scanner.
The same goes for other ports I have tried to open. For example, my Xbox One.
BT are sending me out a replacement Hub to try but I fear that this will have the same result as i have seen a few other people post with the same issues.
If anybody has experienced and or resolved this, please let me know and i will be forever grateful
Thank you

When you do a major network revision always reset the TC to factory and start over.. it simply remembers too much of the last setup.
Plug WAN TC into the HH5 and run through the airport utility again. The TC must go into bridge mode. It then should work fine, but I recommend particularly with Mavericks you use strict naming.
Not apple names.. long, loose and loopy.
Names that are short, 2-10 characters is plenty but make an upper limit of 20.
No spaces..
Pure alphanumeric.. no apostrophe or any other odd character.

Dynamic port configured for FILE adapter is not working

Hi,
I have a simple dynamic port in an orchestration that writes a file to a file location. Here is the configuration
================
FilePort(Microsoft.XLANGs.BaseTypes.Address) = "FILE://c:\\TestFolder\\Out";
FilePort(Microsoft.XLANGs.BaseTypes.TransportType) = "FILE";
================
When I run this orchestration, the dynamic port does not write the file to the folder, however I does not show any error either. It is always in "Ready to Run" state where the message is "Queued Awaiting".
I tried all sorts of combinations like FILE:// FILE:\\ File: file:// file:\\ etc... and also without the moniker, just c:\.... I get the same problem.
when I use a static port(subscribed to the same message) it works fine. When I use a static port ALONGWITH this dynamic port then both works fine !!! I receive 2 files.
but when I use only dynamic port it does not work!!
Anybody knows how to solve it.
THANKS IN AVANCE
PLEASE HELP
Surya

It could be becasue you 're not passing in the file name, Try something like this..
SndPort_Dynamic(Microsoft.XLANGs.BaseTypes.Address)=@"file://C:\Test\Try\Out\Test1.xml";
But even when you don't pass the file name, i was expecting the erro to be like:
The FILE send adapter cannot open file C:\TestFolder\Out\ for writing.
Details: The system cannot find the path specified.
But try with File Name and restart the host instance after the change.
Or use somehting like this:
FilePort(Microsoft.XLANGs.BaseTypes.Address)=@"file://C:\Test\Try\Out\\%MessageID%.xml";
FilePort(Microsoft.XLANGs.BaseTypes.TransportType) = "File";
If this answers your question please mark it accordingly. If this post is helpful, please vote as helpful.

HT1379 The USB ports on my 30" Cinema are not working. The monitor has not been used for a year or so, and the computer is a Mac Book Pro, 1012 model running OS Mavericks. I need to move the computer between two locations, and the other monitor is a 27"

The USB ports on my 30" Cinema HD display appear to not work. The monitor has not been used for almost a year, when I upgraded to a new Mac Book Pro and the 27" retina display. Now I need to move the computer back and forth between two locations using the two displays. The need for operating USB ports is essential. Any ideas. The display appears entirely normal. Am running OS X 10.9.

Disregard, problem solved.

Port Forwarding for RDP 3389 is not working

Hi,
I am having trouble getting rdp (port 3389) to forward to my server (10.20.30.20). I have made sure it is not an issue with the servers firewall, its just the cisco. I highlighted in red to what i thought I need in my config to get this to work. I have removed the last 2 octets of the public IP info for security .Here is the configuration below:
TAMSATR1#show run
Building configuration...
Current configuration : 11082 bytes
version 15.2
no service pad
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname TAMSATR1
boot-start-marker
boot system flash:/c880data-universalk9-mz.152-1.T.bin
boot-end-marker
logging count
logging buffered 16384
enable secret
aaa new-model
aaa authentication login default local
aaa authentication login ipsec-vpn local
aaa authentication login ciscocp_vpn_xauth_ml_1 local
aaa authorization console
aaa authorization exec default local
aaa authorization network groupauthor local
aaa session-id common
memory-size iomem 10
clock timezone CST -6 0
clock summer-time CDT recurring
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-1879941380
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1879941380
revocation-check none
rsakeypair TP-self-signed-1879941380
crypto pki certificate chain TP-self-signed-1879941380
certificate self-signed 01
3082024B 308201B4 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31383739 39343133 3830301E 170D3131 30393136 31393035
32305A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 38373939
34313338 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100BD7E 754A0A89 33AFD729 7035E8E1 C29A6806 04A31923 5AE2D53E 9181F76C
ED17D130 FC9B5767 6FD1F58B 87B3A96D FA74E919 8A87376A FF38A712 BD88DB31
88042B9C CCA8F3A6 39DC2448 CD749FC7 08805AF6 D3CDFFCB 1FE8B9A5 5466B2A4
E5DFA69E 636B83E4 3A2C02F9 D806A277 E6379EB8 76186B69 EA94D657 70E25B03
542D0203 010001A3 73307130 0F060355 1D130101 FF040530 030101FF 301E0603
ip dhcp excluded-address 10.20.30.1 10.20.30.99
ip dhcp excluded-address 10.20.30.201 10.20.30.254
ip dhcp excluded-address 10.20.30.250
ip dhcp pool tamDHCPpool
import all
network 10.20.30.0 255.255.255.0
default-router 10.20.30.1
domain-name domain.com
dns-server 10.20.30.20 8.8.8.8
ip domain name domain.com
ip name-server 10.20.30.20
ip cef
no ipv6 cef
license udi pid CISCO881W-GN-A-K9 sn
crypto vpn anyconnect flash:/webvpn/anyconnect-dart-win-2.5.3054-k9.pkg sequence 1
ip tftp source-interface Vlan1
class-map type inspect match-all CCP_SSLVPN
match access-group name CCP_IP
policy-map type inspect ccp-sslvpn-pol
class type inspect CCP_SSLVPN
pass
zone security sslvpn-zone
crypto isakmp policy 10
encr aes 256
authentication pre-share
group 2
crypto isakmp policy 20
encr aes 192
authentication pre-share
group 2
crypto isakmp key password
crypto isakmp client configuration group ipsec-ra
key password
dns 10.20.30.20
domain tamgmt.com
pool sat-ipsec-vpn-pool
netmask 255.255.255.0
crypto ipsec transform-set ipsec-ra esp-aes esp-sha-hmac
crypto ipsec transform-set TSET esp-aes esp-sha-hmac
crypto ipsec profile VTI
set security-association replay window-size 512
set transform-set TSET
crypto dynamic-map dynmap 10
set transform-set ipsec-ra
reverse-route
crypto map clientmap client authentication list ipsec-vpn
crypto map clientmap isakmp authorization list groupauthor
crypto map clientmap client configuration address respond
crypto map clientmap 10 ipsec-isakmp dynamic dynmap
interface Loopback0
ip address 10.20.250.1 255.255.255.252
ip nat inside
ip virtual-reassembly in
interface Tunnel0
description To AUS
ip address 192.168.10.1 255.255.255.252
load-interval 30
tunnel source
tunnel mode ipsec ipv4
tunnel destination
tunnel protection ipsec profile VTI
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface FastEthernet4
ip address 1.2.3.4
ip access-group INTERNET_IN in
ip access-group INTERNET_OUT out
ip nat outside
ip virtual-reassembly in
no ip route-cache cef
ip route-cache policy
ip policy route-map IPSEC-RA-ROUTE-MAP
duplex auto
speed auto
crypto map clientmap
interface Virtual-Template1
ip unnumbered Vlan1
zone-member security sslvpn-zone
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered Vlan1
arp timeout 0
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
switchport mode trunk
no ip address
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
ip address 10.20.30.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
ip local pool sat-ipsec-vpn-pool 10.20.30.209 10.20.30.239
ip default-gateway 71.41.20.129
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip dns server
ip nat inside source list ACL-POLICY-NAT interface FastEthernet4 overload
ip nat inside source static tcp 10.20.30.20 3389 interface FastEthernet4 3389
ip nat inside source static 10.20.30.20 (public ip)
ip route 0.0.0.0 0.0.0.0 public ip
ip route 10.20.40.0 255.255.255.0 192.168.10.2 name AUS_LAN
ip access-list extended ACL-POLICY-NAT
deny   ip 10.0.0.0 0.255.255.255 10.20.30.208 0.0.0.15
deny   ip 172.16.0.0 0.15.255.255 10.20.30.208 0.0.0.15
deny   ip 192.168.0.0 0.0.255.255 10.20.30.208 0.0.0.15
permit ip 10.20.30.0 0.0.0.255 any
permit ip 10.20.31.208 0.0.0.15 any
ip access-list extended CCP_IP
remark CCP_ACL Category=128
permit ip any any
ip access-list extended INTERNET_IN
permit icmp any any echo
permit icmp any any echo-reply
permit icmp any any unreachable
permit icmp any any time-exceeded
permit esp host 24.153. host 66.196
permit udp host 24.153 host 71.41.eq isakmp
permit tcp host 70.123. host 71.41 eq 22
permit tcp host 72.177. host 71.41 eq 22
permit tcp host 70.123. host 71.41. eq 22
permit tcp any host 71..134 eq 443
permit tcp host 70.123. host 71.41 eq 443
permit tcp host 72.177. host 71.41. eq 443
permit udp host 198.82. host 71.41 eq ntp
permit udp any host 71.41. eq isakmp
permit udp any host 71.41eq non500-isakmp
permit tcp host 192.223. host 71.41. eq 4022
permit tcp host 155.199. host 71.41 eq 4022
permit tcp host 155.199. host 71.41. eq 4022
permit udp host 192.223. host 71.41. eq 4022
permit udp host 155.199. host 71.41. eq 4022
permit udp host 155.199. host 71.41. eq 4022
permit tcp any host 10.20.30.20 eq 3389
evaluate INTERNET_REFLECTED
deny   ip any any
ip access-list extended INTERNET_OUT
permit ip any any reflect INTERNET_REFLECTED timeout 300
ip access-list extended IPSEC-RA-ROUTE-MAP
deny   ip 10.20.30.208 0.0.0.15 10.0.0.0 0.255.255.255
deny   ip 10.20.30.224 0.0.0.15 10.0.0.0 0.255.255.255
deny   ip 10.20.30.208 0.0.0.15 172.16.0.0 0.15.255.255
deny   ip 10.20.30.224 0.0.0.15 172.16.0.0 0.15.255.255
deny   ip 10.20.30.208 0.0.0.15 192.168.0.0 0.0.255.255
deny   ip 10.20.30.224 0.0.0.15 192.168.0.0 0.0.255.255
permit ip 10.20.30.208 0.0.0.15 any
deny   ip any any
access-list 23 permit 70.123.
access-list 23 permit 10.20.30.0 0.0.0.255
access-list 24 permit 72.177.
no cdp run
route-map IPSEC-RA-ROUTE-MAP permit 10
match ip address IPSEC-RA-ROUTE-MAP
set ip next-hop 10.20.250.2
banner motd ^C
UNAUTHORIZED ACCESS TO THIS NETWORK DEVICE IS PROHIBITED.
You must have explicit permission to access or configure this device. All activities performed on this device are logged and violations of this policy may result in disciplinary and/or legal action.
^C
line con 0
logging synchronous
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0
access-class 23 in
privilege level 15
logging synchronous
transport input telnet ssh
line vty 1 4
access-class 23 in
exec-timeout 5 0
privilege level 15
logging synchronous
transport input telnet ssh
scheduler max-task-time 5000
ntp server 198.82.1.201
webvpn gateway gateway_1
ip address 71.41. port 443
http-redirect port 80
ssl encryption rc4-md5
ssl trustpoint TP-self-signed-1879941380
inservice
webvpn context TAM-SSL-VPN
title "title"
logo file titleist_logo.jpg
secondary-color white
title-color #CCCC66
text-color black
login-message "RESTRICTED ACCESS"
policy group policy_1
   functions svc-enabled
   svc address-pool "sat-ipsec-vpn-pool"
   svc default-domain "domain.com"
   svc keep-client-installed
   svc split dns "domain.com"
   svc split include 10.0.0.0 255.0.0.0
   svc split include 192.168.0.0 255.255.0.0
   svc split include 172.16.0.0 255.240.0.0
   svc dns-server primary 10.20.30.20
   svc dns-server secondary 66.196.216.10
default-group-policy policy_1
aaa authentication list ciscocp_vpn_xauth_ml_1
gateway gateway_1
ssl authenticate verify all
inservice
end

Hi,
I didnt see anything marked with red in the above? (Atleast when I was reading)
I have not really had to deal with Routers at all since we all access control and NAT with firewalls.
But to me it seems you have allowed the traffic to the actual IP address of the internal server rather than the public IP NAT IP address which in this case seems to be configured to use your FastEthernet4 interfaces public IP address.
There also seems to be a Static NAT configured for the same internal host so I am wondering why the Static PAT (Port Forward) is used?
- Jouni

Mini Display Port to Dual Link DVI Does Not Work Right

Somebody said here that this was an isolated problem. Well, I just got my new MacBook Pro 15", used the adapter to hook to the 30" Dell monitor, and it works a few minutes, then the screen distorts.
Count me among the isolated problems- it is beginning not to look isolated.
Now, do I wait on Apple to fix the problem, or do I return the MacBook Pro while still in the return period?

Hi, Matt, and welcome to Apple Discussions.
The Matrox Support only told me that the new MacBook Pro with Mini Display Port is not supported, but as it's working for 2x1680x1050 with the Dual-Link DVI adapter, I was wondering if the Mini Display Port to Dual-Link DVI Adapter could be the problem.
I suspect that what Matrox Support meant when they said "not supported" was, in fact, "not supported": i.e., they've tried it and it doesn't work satisfactorily. You've tried it too, and found that to be true. Now you just need to come to terms with the fact. Matrox is quite open about it; it's not a secret. See the 9400M/9600MGT MacBook Pro entry in this compatibility table from Matrox's web site:
http://www.matrox.com/graphics/en/support/compatibility/gxm/resolutions/

Cannot connect to port 25 externally and owa is not working

Hi all,
just finished installing exchange 2013 and all went well.   Internally, everything works perfectly.   However, I then moved my testing externally.   Browsing to https://mydomain/owa times out - as does https://mydomain/ecp
Also, I cannot telnet to my mail server either: telnet mydomain 25 times out. I can though telnet mydomain 143 and telnet mydomain 110 no problem.
I have setup the receive connector as per the instructions (in fact, it was already setup) the frontend default allows anonymous access (as it should). Windows firewall is off. Router forwarding ports fine.
I can telnet 25 locally and as I said, everything works internally.    Clearly, there is another step that has to be taken to allow external access to the port 25 and also for owa and ecp. I have double checked the SERVERS - VIRTUAL
DIRECTORIES area and all the external url are correct. Can someone help please?

Ok, I rechecked my router page by page and have found one solution .. .the https management page of the router defaults to 443 - so have changed that to 4443, rebooted router and can now access my http://mydomain/owa - so that is good. However, still
cannot telnet to port 25 on the exchange server from external. The port forwarding is definitely correct for port 25.
I have rechecked the receive connector: MAIL FLOW - RECEIVE CONNECTORS - DEFAULT FRONTEND SERVER
and under security - anoymous users is checked.   That SHOULD let me connect yes? But it does not.
Where else does this need to be changed - can you advise?
regards
steve

The ethernet port on the thunderbolt display is not working

The ethernet is working when the cable is connected directly to my mac laptop but when connected the thunderbolt display there is no connection. Is there some type of set up for the ethernet connection or can this port just be broken?
Thanks for the help!

Afterthought on an older post: it isn't immediately clear that the Ethernet port on the Thunderbolt Display works through the "Display Ethernet" interface, rather than through the "Thunderbolt Ethernet" interface. The latter was already present in the list of network interfaces in Network Preferences, while the former had to be added via the + button --- at least that was the case when I installed the TB display to work with my 15-inch MacBook Pro Retina this week.
The AppleCare rep didn't know the difference either and agreed with me that it was puzzling that using the Thunderbolt Ethernet adapter on the Thunderbolt port of the display did work, wheras using the Ethernet port directly didn't (even though there were lights flashing on the Ethernet port of that other computer I tried to connect to in Internet Sharing mode). Close reading of the above posts made me go look for that mysterious "Display Ethernet" interface... thank you Clinton!

SF 300-24P 24-Port 10/100 PoE - Video is not working smoothly

Similar Messages

Maybe you are looking for