SFP-10G-ZR support on Catalyst 4500 SUP6E

Hello,
is the SFP-10G-ZR supported on the SUP6-E with the OneX converter?
BR
O.G

End-of-Sale and End-of-Life Announcement for the Cisco Catalyst 4500 Supervisor Engine 6-E
The chances of your SE submitting the PER is now ZERO. You'll be forced to upgrade to Sup7E.

Similar Messages

Can the SFP-10G-SR down-support connect to SFP 1000BASE-SX ?

Hi everybody:
today i use the SFP+ "SFP-10G-SR" in Cisco Catalyst 2960S-48TD-L connect to 1000BASE-SX SFP in 6509's module WS-X6724-SFP.
the port setting is trunk,but they don't work, even the led don't flush. then i also use the 1000BASE-SX SFP to replace SFP+ SFP-10G-SR in
2960S-48TD-L, then they cany working.
i look up the cisco data sheet , there are no data sheet to satament the 10G sfp+ can't down support 1G sfp. so i want to confirm the problem.
otherwise, the 10 SFP+ only can use for 10G SFP+ ; can't down suport 1G SFP.
this means: if you want to use the 10G SFP+ the other old device also need to replace.
thanks~for your help!!

Hi Marvin,
I found this conversation today, as I am looking for answer on question similar to question that Jerry asked, while opening this discussion.
So, my problem is the following. At some location, I need two 10GB and one 1GB connection over optical cables. To minimize costs, I tried with WS-C2960X-48FPD-L, but as it contain only two SFP+ ports, I tried with two WS-C2960X-24PD-L that will be connected with stack modules.
So, having two WS-C2960X-24PD-L, I can have 2 x 2 1GB SFP+ ports. There are two opened questions:
1. Can I put 1GB SFP transceiver module in SFP+ port (as I must have one 1GB connection to remote site)?
2. Can I use stack of two mentioned 2960 24-port switches, in a way that I use one of them for two 10GB connections (using SFP+ ports for 10GB connection), and second member of the stack in a way that one (of two available) SFP+ port is used for 1GB SFP connection (using SFP+ port as mentioned in question 1)?
I am not sure if your previous statement covers my questions, as it is not clear if 1GB SFP transceiver can be inserted in SFP+ port on WS-C2960X-24PD-L (or any other switch that has SFP+ port).

Cisco Nexus 5548UP support SFP-10G-LRM ?

Hi all, I have a question about Cisco Nexus 5548UP. Is Cisco Nexus 5548UP support SFP-10G-LRM ? Because in CCW, i can't configure the SFP-10G-LRM. There is only SFP-10G-LR, SR, and the others, but there's no LRM. Pelase help me to answer this question. Thanks a lot

The LRM is s special case transceiver which supports 10 Gbps over older FDDI grade multimode fiber when used with a mode conditioning patch cord. It is not supported on the Nexus 5548UP.
The SFP-10G-LR is used with single mode fiber for spans up to 10 km in length. It is supported on the 5548UP (and most every platform of Cisco's that takes SFPs).
Please see the product data sheet here.

SFP-10G-AOC10M does not detected by WS-C2960X-48FPD-L

Hello.
I've got two SFP-10G-AOC10M optical transceiver modules, and want to use them as uplinks for Catalyst 2960-x switch stack to 4500-X.
When I insert SFP modules to Cat2960-X I get next messages in log:
%PHY-4-SFP_NOT_SUPPORTED: The SFP in Gi4/0/50 is not supported
%PM-4-ERR_DISABLE: gbic-invalid error detected on Gi4/0/50, putting Gi4/0/50 in err-disable state
%PHY-4-SFP_NOT_SUPPORTED: The SFP in Gi5/0/50 is not supported
%PM-4-ERR_DISABLE: gbic-invalid error detected on Gi5/0/50, putting Gi5/0/50 in err-disable state
Looks like switches detected this modules as 1G not 10G.
According to Cisco 10-Gigabit Ethernet Transceiver Modules Compatibility Matrix these modules should be supported by Cat 2960-X with 15.0(2)EX IOS release. I had 15.0(2)EX5 release and even upgraded to 15.0(2a)EX5.
#show interfaces Gi5/0/49 transceiver properties
Diagnostic Monitoring is not implemented.
Name : Gi5/0/49
Administrative Speed: auto
Administrative Duplex: auto
Administrative Auto-MDIX: on
Administrative Power Inline: N/A
Operational Speed: auto
Operational Duplex: auto
Operational Auto-MDIX: on
Media Type: unknown
I've inserted two other modules in this ports and they are detecting correctly:
#show interfaces Gi5/0/50 transceiver properties
Diagnostic Monitoring is not implemented.
Name : Gi5/0/50
Administrative Speed: auto
Administrative Duplex: auto
Administrative Auto-MDIX: on
Administrative Power Inline: N/A
Operational Speed: auto
Operational Duplex: auto
Operational Auto-MDIX: on
Media Type: 10/100/1000BaseTX SFP
#show interfaces Te4/0/2 transceiver properties
Diagnostic Monitoring is not implemented.
Name : Te4/0/2
Administrative Speed: 10000
Administrative Duplex: full
Administrative Auto-MDIX: on
Administrative Power Inline: N/A
Operational Speed: 10000
Operational Duplex: full
Operational Auto-MDIX: off
Media Type: SFP-10GBase-CX1
Any ideas?

Hello.
That is the problem. Switch has 48 Gigabit ports and they appear as Gi4/0/1-Gi4/0/48. And two uplink ports for SFP or SFP+ modules. 10Gig uplinks module should be detected as Te4/0/1 and Te4/0/2. Gigabit will be detected as Gi4/0/49 and Gi4/0/50.
Once I insert SFP-10G-AOC10M to the switch uplink port I get messages in logs:
%PHY-4-SFP_NOT_SUPPORTED: The SFP in Gi4/0/50 is not supported
%PM-4-ERR_DISABLE: gbic-invalid error detected on Gi4/0/50, putting Gi4/0/50 in err-disable state
So instead to be detected as Te4/0/2 it is detected as Gi4/0/50.
I've tried to insert into uplink ports two other modules: GLC-T (1gig) and SFP-H10GB-CU3M. And they are detected correctly(see two last outputs in first post).

Subinterfaces - hardware limitation on catalyst 4500-X

Hi there,
We are currently building a VSS and our design has L3 subinterfaces however we have hit a major wall while trying to do the following
         Create physical subinterface on VSS switch – Fail
         Create port-channel subinterface on VSS switch – Fail
         Create physical subinterface on standalone switch – Fail
         Create port-channel subinterface on standalone switch – Fail
Below is the output showing that the option of a subinterfaces seems to be available, but it still doesn’t apply
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#int po1
Switch(config-if)#no swi
Switch(config-if)#no switchport
Switch(config-if)#int po1.1
                      ^
% Invalid input detected at '^' marker.
Switch(config)#int po
Switch(config)#int port-channel 1.?
<0-4294967295> Port-channel interface number
Switch(config)#int port-channel 1.1
                   ^
% Invalid input detected at '^' marker.
Switch(config)#int tenGigabitEthernet 1/1
Switch(config-if)#no swi
Switch(config-if)#no switchport
Switch(config-if)#exit
Switch(config)#int tenGigabitEthernet 1/1.?
<0-4294967295> TenGigabitEthernet interface number
Switch(config)#int tenGigabitEthernet 1/1.1
                    ^
% Invalid input detected at '^' marker.
Switch(config)#
Here’s the show ver and show module output
Switch#show ver
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.07.00.E RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Sun 07-Dec-14 22:13 by prod_rel_team
Cisco IOS-XE software, Copyright (c) 2005-2014 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0.
(http://www.gnu.org/licenses/gpl-2.0.html) For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: 15.0(1r)SG11
Switch uptime is 5 minutes
System returned to ROM by power-on
Running default software
Jawa Revision 2, Winter Revision 0x0.0x41
Last reload reason: power-on
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
*Apr 29 18:56:44.596: %SYS-5-CONFIG_I: Configured from console by console
License Information for 'WS-C4500X-32'
    License Level: entservices   Type: Permanent
  Next reboot license Level: entservices
cisco WS-C4500X-32 (MPC8572) processor (revision 9) with 4194304K bytes of physical memory.
Processor board ID JAE191304FG
MPC8572 CPU at 1.5GHz, Cisco Catalyst 4500X
Last reset from PowerUp
1 Virtual Ethernet interface
32 Ten Gigabit Ethernet interfaces
511K bytes of non-volatile configuration memory.
Configuration register is 0x2101
Switch#
Switch#show module
Chassis Type : WS-C4500X-32
Power consumed by backplane : 0 Watts
Mod Ports Card Type                              Model              Serial No.
---+-----+--------------------------------------+------------------+-----------
1    32 4500X-32 10GE (SFP+)                   WS-C4500X-32       JAE191304FG
M MAC addresses                    Hw Fw           Sw               Status
--+--------------------------------+---+------------+----------------+---------
1 b0aa.7777.5840 to b0aa.7777.585f 2.0 15.0(1r)SG11 03.07.00.E       Ok
System Failures:
Power Supply:   bad/off (see 'show power')
Switch#
All we can find is a little note on the release notes:
A Catalyst 4006 switch with Supervisor Engine III does not support subinterfaces or the encapsulation keyword on
Layer 3 Fast Ethernet, Gigabit Ethernet, 10-Gigabit Ethernet interfaces.
Source: http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/XE3-7-0E/15-23E/configuration/guide/xe-370-configuration/l3_int.html
I am assuming this restriction applies to this platform but other than that there is nothing specifying we can't do this. Anyone out there has hit the same issue? or can anyone confirm this is an actual platform restriction
Thank you

Hi,
The 4500 and 4500x series switches do not support sub-interfaces. Only 6500 series support sub-interfaces.
HTH

Catalyst 4500 Ethernet and fibre channel passthru

dear sir,
anyone have any idea / documentation showing that the belows device 1.) & 2.) can support Ethernet and fibre channel passthru ? thanks.
1.) WS-X4424-GB-RJ4 (Catalyst 4500 24-port 10/100/1000 Module (RJ45)
2.) WS-X4306-GB (Catalyst 4500 Gigabit Ethernet Module, 6-Ports (GBIC)

You're welcome. Check below for the module info. And there is description about support of fibre channel passthru.
http://www.cisco.com/en/US/products/hw/switches/ps4324/products_data_sheet0900aecd802109ea.html
You can also seach Cisco web for more info.
Hope this helps.

WS-X4306-GB - Catalyst 4500 6-port GBIC Module & FC Tape Libraries

WS-X4306-GB - Catalyst 4500 6-port GBIC Module & FC Tape Libraries
I have several Tape Autoloader Libraries from Dell which have Fibre Channel interfaces. I have loop switches that these connect to today. I also have a Catalyst 4506 with a WS-X4306-GB - 6-port GBIC Module. I would like to use the X4306 as a loop switch. Some of the libraries can also connect via point-to-point FC.
Can this be done? If yes, how do I start in making this happen?
Thank You.

Sorry but the Catalyst 4500 does not support Fibre Channel connections on the WS-X4306-GB (or on any card). It's strictly an Ethernet switch. Reference
To mix and match Ethernet and FC interfaces, you'd have to be on a new platform like the Nexus 5k series - specifically the UP (Unified Port) variants.

QoS trust dscp or cos on catalyst 4500

We have a 4510R with Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software cat4500e-UNIVERSALK9-M), Version 03.05.02.E RELEASE SOFTWARE (fc1).
I want use qos trust dscp or qos trust cos on the interface conected to other cisco switch or wlan controller.
The current IOS version, do not support qos trust dscp:
SW(config)#interface gi10/16
SW(config-if)#qos tr
SW(config-if)#qos trust ?
device trusted device class
extend Extend trust through a connected device
SW(config-if)#qos trust device ?
cisco-phone   Cisco IP Phone
cts           Cisco-telepresence
ip-camera     Cisco video surveillance camera
media-player Cisco Digital Media Player
SW(config-if)#qos trust device
What is the software that I need for this?. I tried with command lookup tool but the cat4500 do not appears.

That is even new for me.
I did a search and found that, now a days you no longer have to provide the Trust DSCP command, it is by default trusted.
Went through this White Paper and excerpts are below:
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-4500-series-switches/white_paper_c11-539588.html
The answer to your question comes from the following excerpt :-
"Previously supervisor engines relied on “port trust” to classify traffic; however, this does not fall into the MQC CLI construct. MQC provides a more flexible capability, i.e. all traffic is trusted by default, an administrator can change this trust state using a policy map. Another difference is the “internal DSCP” value used within the switch to place packets in the proper queue.
Cisco Catalyst 4500E Supervisor Engines do not use “internal DSCP”; rather, it relies on explicit matching of QoS values using class maps so that packets can be placed in the correct queue.
Also, note that there is no specific priority queue: it is not queue 3 or queue 1. The priority queue is simply configured within a class; therefore, it is not tied to a specific queue. One final difference is that of classification. Cisco Catalyst 4500E Supervisor Engines provide sequential classification rather than parallel. This allows the network administrator to classify traffic at egress based on the ingress markings. These markings can be done unconditionally, using a policer or using a table map. Based on these changes, QoS CLI will now be more contiguous on the Supervisor Engines as it will now have standard Cisco MQC CLI, making configuration management much simpler"
HTH,
Please rate all helpful posts.
Regards

Catalyst 4500 Hi CPU

Hi,
I have an issue with a Catalyst-4500 (4507R-E, ipbase, 12.2.46SG), that is running very hi CPU since some days:
By investigating, I observed a couple of processes that are realy CPU-consuming:
I don't know where to look ...
Some help and/or some suggestion ?
Best regars,
Claudio

Two good resources for troubleshooting high CPU on the 4K
High CPU Utilization on Cisco IOS Software-Based Catalyst 4500 Switches
http://www.cisco.com/c/en/us/support/docs/switches/catalyst-4000-series-switches/65591-cat4500-high-cpu.html
Troubleshooting High CPU on the Catalyst 4500-E Series Switch
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/troubleshooting/cpu_util.html
HTH
Luke

Catalyst 4500, supervisor II+, EIGRP

Hi,
We're bought a catalyst 4500 sup II+ with image cat4000-i9s-mz.122-25.EWA4.bin
In feature navigator isn't anything about EIGRP in this image, but in CLI I may configure EIGRP.
How is that possible?
thx

Hi,
You can only configure the EIGRP stub on the Sup 2+. EIGRP fully is not supported on sup2+.
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/12_2_31s/conf/l3_int.htm#wp1042868
http://www.cisco.com/en/US/products/hw/switches/ps4324/products_data_sheet09186a0080197424.html
HTH, Please rate if it does.
-amit singh

SFP-10G-LRM compatible?

I want to perform upgrades part by part and would like to know if I
Can I connect a SFP-10G-LRM to a GLC-LH-SM 1gb interface over OM1 fiber atleast until I upgrade the core side of the network and the under ground fiber?

Unfortunately, optical transceiver modules do not auto negotiate for speed. Therefore, you cannot connect a 10Gbps interface to a 1Gbps interface. You need to upgrade both ends before the circuit can be completed.
If you need equipment to support the intermediate step in the upgrade cycle, you might look at purchasing Cisco Refurbished Products.

SFP-10G-LRM modules with MM fiber OM3

Hi All,
Can the Cisco SFP-10G-LRM transceiver be used with Multimode OM3 fiber? if so, what would be the cable distance?
thanks

The SFP+ data sheet does indicate support for OM3 & OM4 fibers (no launch cable required). 220 meters looks to be the link length spec.

Upgrade Catalyst 4500 Supervisor Engine 8-E(IOS XE Software)

Folks,
We are looking to upgrade the Catalyst 4500 Supervisor Engine 8-E(IOS XE Software). As of now we are running on 3.3.1XO and as per the Cisco notes version 3.3.2XO which is suggested version.
I would like to find some comparison documents on both these version and establish if there is a need to do the upgrade. What are the fixes that have been done in this version.
Thanks,!!

Hi Nikhil,
Please find release notes of version 3.3.2XO below which can provide you the details to upgrade.
Mainly you need to refer the features it supports and resolved cavets (which means the bugs resolved fro the earlier version on to this.).
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/release/note/OL_29983-01.html
HTH
Regards
Inayath
*Plz rate if this info is helpfull.

Catalyst 4006 chassis with CATALYST 4500 SUPERVISOR V

Hi Experts,
Can I use CATALYST 4500 SUPERVISOR V(WS-X4516) in an old 6-slot catalyst 4006 chassis( WS-C4006). I want to run the latest IOS available and I have the following line cards:
WS-X4232-RJ-XX
WS-X4418-GB
WS-X4148-RJ
thanks and regards
alex

Hi Alex
Yes you can run the Sup V in the 4006 chassis. See this link
http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/hardware/module/guide/01overvw.html#wp1015031
The Sup V also supports the WS-X4418-GB and WS-X4148-RJ modules - see attached link
http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps4324/product_data_sheet09186a00801fcaba_ps2797_Products_Data_Sheet.html
HTH
Jon

SFP-10G-LR on Cisco WS-C3650-24PD-L

Dear All,
Right now we have the problem, that SFP-10G-LR are not working on Cisco 3650 10G Ports - IOS XE 3.3.0SE (see TE1/1/3 and picture in attachment). Which is really strange, becuase in the compatability matrix and in the datasheet this Module is supported. What is also strange is, that not orginial Cisco SFP+ LR Transceivers are working (see TE1/1/4)
*Mar 20 09:15:07: %PLATFORM_PM-6-MODULE_ERRDISABLE: The inserted SFP module with interface name Te1/1/3 is not supported
*Mar 20 09:15:07: %PM-4-ERR_DISABLE: gbic-invalid error detected on Te1/1/3, putting Te1/1/3 in err-disable state
Te1/1/3 to CSAARAWA01, Te1 err-disabled 1 auto auto unknown
Te1/1/4 to GSAARKLBEG02, T notconnect 1 full 10G SFP-10GBase-LR
Has anyone made similiar experiences?
Many Thanks,
Manuel

Dear Dima L,
I will check this tomorrow... but expect the same error.
Regards,
Manuel

SFP-10G-ZR support on Catalyst 4500 SUP6E

Similar Messages

Maybe you are looking for