Sfp-h10gb-acu10m compatibility

Dear all,
Does anybody know if SFP-H10GB-ACU10M cable is compatible with Cisco Catalyst 2960-S series? According to the compatibility matrix it is not compatible with Cisco IOS release 12.2 (53) SE1, but i would like to know if it would be compatible with another IOS version.
Thanks in advance,
Carmen

I suspect it might have something to do with the CVR-X2-SFP10G, seeing that the converter module data sheet also does not list any length of the Active Twinax cables being compatible.
I am trying to reach out to someone within the Product Mgmt org to see if they can provide an answer... but my contacts are old....

Similar Messages

Compatibility between ASR9K and SFP-H10GB-ACU10M

Hi Everyone,
I have in my environment two ASR9K with module A9K-16T/8-B and I am trying to connect using the Active Twinax cable 10M (SFP-H10GB-ACU10M), however when I connected the cable, shows the following error:
State:
Administrative state: enabled
Operational state: Down (Reason: Security failure (not a valid part))
LED state: Red On
Phy:
Media type: Not known
Optics:
Vendor: CISCO-TYCO
Part number: 2163675-2
Serial number: TED1618U0H0
I checked the compatibility list and apparently okay, as shown in the link below:
http://www.cisco.com/c/en/us/products/collateral/routers/asr-9000-series-aggregation-services-routers/data_sheet_c78-624747.html
Please, the community can help me?
Best Regards,
Vitor Nakano

The twinax copper 10 Gig SFPs such as the one you cite are prefabricated cables with transceivers already attached. See the pictures on the top left of the data sheet to visualize what you get.
Controlling that mating of transceiver to the copper media is how they are able to ensure reliable operation at 10 Gbps over copper.

SFP-H10GB-ACU10M

Dear All,
does SFP-H10GB-ACU10M come with SFP+ connectors?
or it is just a cable and we need to provide the SFP+ Transceivers??
thanks

The twinax copper 10 Gig SFPs such as the one you cite are prefabricated cables with transceivers already attached. See the pictures on the top left of the data sheet to visualize what you get.
Controlling that mating of transceiver to the copper media is how they are able to ensure reliable operation at 10 Gbps over copper.

N5K:does active Twinax SFP-H10GB-ACU7M support FCoE

Hi
does SFP-H10GB-ACU7M and SFP-H10GB-ACU10M support FCoE if they are used in Nexus5000 running 5.0.3
I heard rumors thats it could be that these active Twinax do not support FCoe because they could net reach the BER which is necessary for FCoE
KR
Hubert

Hubert,
They're in the compatibility matrix but only show being supported by NX-OS 4.2(1)N2(1)
http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6974.html
I don't know about the Bit Error Rate though. The fact that they're supported in 4.2.1 but not in 5.x makes me think its a testing thing rather than a functional BER thing. I could be wrong on that though. Short answer is not supported.
--Justin

SFP-H10GB-CU5M and HP NICs

Hello,
Can anyone confirm that SFP-H10GB-CU5M can work with HP NICs (HP Ethernet 10Gb 2-port 530FLR-SFP+ Adapter, or modifications on same chipset) ?

Hello teater,
SFP-H10GB-CU5M1 is supported with Sup2T and CVR-X2-SFP10G starting 12.2(50)SY.
I will look into fixing the compatibility matrix to fill this missing cell.
Thanks,
~Amer

Cat6807 + VS-S2T-10G + CVR-X2-SFP10G + SFP-H10GB-CU5M?

Is the Cisco OneXConverter Module, CVR-X2-SFP10G, compatible with VS-S2T-10G in a 6807 using a SFP-H10GB-CU5M cable to connect to an ASA5585?
Description of the CVR-X2-SFP10G, which states it is compatible with the SFP-H10GB-CU5M:
http://www.cisco.com/en/US/prod/collateral/modules/ps5455/data_sheet_c78-547521.html
Compatibility matrix which eludes the CVR-X2-SFP10G module is compatible with the VS-S2T-10G and SFP-H10GB-CU5M but only if the SFP-H10GB-CU5M is version 2. I am not comfortable with this chart as it does not list the software requirement which could imply it is not compatible when used with the SFP-H10GB-CU5M.
http://www.cisco.com/en/US/partner/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6974.html
snippit of chart:
Platform
Switch or Module
Transceiver Model
Minimum Software Release Required
VS-S2T-10G
VS-S2T-10G-XL
WS-X6816-10G-2T
WS-X6816-10G-2TXL
WS-X6908-10G-2T
WS-X6908-10G-2TXL
(With CVR-X2-SFP10G converter for X2 ports)
SFP-H10GB-CU1M1
SFP-H10GB-CU3M1
SFP-H10GB-CU5M1
SFP-10G-SR
SFP-10G-LRM
SFP-10G-LR
12.2(50)SY
12.2(50)SY
1 Only Version -02 or later is supported.

Hello teater,
SFP-H10GB-CU5M1 is supported with Sup2T and CVR-X2-SFP10G starting 12.2(50)SY.
I will look into fixing the compatibility matrix to fill this missing cell.
Thanks,
~Amer

SFP+ Twinax cable compatibility

Hi Guys,
Does anybody know if the 'SFP+ Twinax' active or passive cables are compatable with the HP ethernet 10gb 2-port 530sfp+ adapters? I'm struggling to find/confirm if they are compatible or not.
Cheers

I've purchased a SFP-H10GB-CU3M (non-branded) TwinAx cable and have successfully connected from a HP NC552SFP 10Gb 2-port adapter (HP DL360p Gen8) into a 3750X (WS-C3750X-24T-S) 10GB (C3KX-NM-10G) module.
Once I receive my 4500X-16SFP switch, I hope to connect this into 3 dual port 10Gb vSphere hosts as well as my VNX SAN (10Gb SFP).
Finding anyone from EMC or Cisco that will confirm this solution is possible was impossible...so I hope mine will work!

4500x VSS and SFP-H10GB-CU1M

Hello
I have (2) Cisco 4500x with a VSS config. I als have a couple cables "SFP-H10GB-CU1M".
I want to make sure I have this physically setup correctly. I have searched but not found anything specific enough.
Please review and advise.

Yes, all device packages are installed (including 7.0) and the Pi 2.1.2 patch.
Info from "ifm_config_archive.log" when trying Archive the Configuration:
[2014-12-09 19:58:11,300] [pool-37-thread-5] [service] [ERROR] - Thread Id : [9,460] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching VLAN file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]'
Maybe the Prime don't know where to find the vlan.dat on the 4500X-VSS ?
#dir cat4000_flash:
Directory of cat4000_flash:/
1 -rw- 2236 <no date> vlan.dat
sysObjectID (1.3.6.1.2.1.1.2) is
.iso.org.dod.internet.private.enterprises.cisco.ciscoProducts.cat4xxxVirtualSwitch
That is not the expected and supported value "4500X-16" above
Update: Error on fetching running and startup config as well:
[2014-12-09 20:24:21,818] [pool-37-thread-9] [service] [ERROR] - Thread Id : [10,013] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching RUNNINGCONFIG file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]
[2014-12-09 20:25:31,882] [pool-37-thread-9] [service] [ERROR] - Thread Id : [10,013] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching STARTUPCONFIG file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]

Can use SFP-H10GB-CU3M to connect 6120XP to Cat6K Switch?

Can use SFP-H10GB-CU3M OR SFP-H10GB-CU5M to connect 6120XP to Cat6K Switch?

You dont have to connect to Nexus equipment. Your LAN can be anything as long as you can connect the UCS system to it.
Currently you need a switch with 10GE ports to uplink from your 6100s.
I believe that in the next version of the firmware/software in UCS you will be able to connect your 6100s to the LAN using 1G ports.
Nuno Ferreira

SFP-H10GB-CU1M SFP+ Copper Cable module speed shows as Unknown

I have connected 2 SG500x switches using an SFP-H10GB-CU1M SFP+ Copper Cable module. Since the port shows as a 10G port, I would expect the speed to show as 10G as well. However, it shows as "Unknown". This doesn't leave me with confidence that it is being recognized properly. The link is working properly, but I haven't run tests to verify if I'm getting full 10G throughput or not. I'll work on that. In the meantime, anyone have any ideas as to the proper behavior here? Shouldn't it show 10G as the link speed?

Hi Robert,
I love the GUI, so easy to navigate, when you get the feel for the layout of the switch options. So going to ask you to use the GUI to find the stacking status and speed between the switches..
Step 1. Select help at the top right of the GUI screen,
Step 2. Type in as a search option "stack speed " then clock go
see my screen capture below,.
( The switch has basically an Administration guide built in., a really cool cool feature )
So you see the following screen capture that shows the option that I selected;
Followed the instruction outlines in the online help text, the following screen capture shows me the stacking speed.,
I have two by SG500-52P, my SG500X are loaned out to a partner to evaluate, so i can only run 5G over the SFP-H10GB-CU1M stacking module on this platform.
Hope this helps you clarify where to find stack module speed.
regards Dave
Rate this post

Connecting Nexus 2232PP-10GE to a Qlogic 10Gb CNA for IBM System X using PROSFP's SFP-H10GB-ACU7M cable

The cisco nexus interface is only detecting the type as
SFP-H10GB-CU1M, instead of SFP-H10GB-ACU7M. Is the PROSFP transceiver and cable supported by Cisco's Nexus? Is this a supported connection?
Thanks....

X2-10GB-LRM to SFP-10G-SR= Compatibility

Hi,
Can you help me in this ?
I have two 10Gig modules.
On 6500, i have X2-10GB-LRM and on 3750-x i have SFP-10G-SR= .
you can use it with fiber cable and patch cord to connect the two devices?
thanks

Hello,
SFP-10G-SR is a MMF and it uses a LC duplex connector.
X2-10GB-LRM is also a MMF and it uses LC duplex connector.
so they are compatible.
Link
Under 6xxx series switches you will both transceivers as part of the supported devices.
http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matri/OL_6974.html#wp99798
Under 3xxx series switches:
http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matri/OL_6974.html#wp48759
Link for 10GBASE X2 modules:
http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6574/product_data_sheet0900aecd801f92aa.html
10 transceiver modules compatibility matrix:
http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6974.html
Look for Table 1 10-Gigabit Ethernet Transceiver Module Models
Thank,
Haihua

SFP-10G-LR and SFP-10G-LRM Compatibility

Hello,
Has anyone had success/experience running across OS2 SM with a SFP-10G-LR at one end and a SFP-10G-LRM at the other, where the total link length is <300m?
Thanks,
Andrew

Dear Dima L,
I will check this tomorrow... but expect the same error.
Regards,
Manuel

10GE Twinax cables connecting to servers NIC which accept 10GE SFP+

Anyone has any real life experience of using the Cisco 10GE Twinax cables to connect this to servers with NIC cards that accept SFP+? I'm talking servers like HP and Dell which have 10GE NIC cards. For the switch, I would be using Nexus 5548UP. The SFP+ part number would be SFP-H10GB-ACU10M.
The SFP-10G-SR is too expensive and I'm looking at 10GE Twinax cables as an alternative but am quite concerned about the compatability.

Yes, the twinax cables are all we ever use to connect servers to Nexus 5ks. We have used them with both Qlogic and Emulex CNAs. If the server is more than 10m from the switch the 10G-SR and 50 micron fiber are required.

Link C3850 to Dell 8132F Using SFP Interconnect (copper)

I am introducing new Cisco C3850 switches into an existing Dell environment. This will be a phased replacement so I have a need to link the 3850's to Dell 8132F's. My 3850's each have a C3850-NM-4-10G network module and the Dell switches have SFP+ ports. So the plan is to link the switches using 10GB links. I would like to use the copper SFP+ interconnect cables. But the distance between the switches require a 10 meter cable (SFP-H10GB-ACU10M). But the 3850 specs only list the 5 meter (SFP-H10GB-CU5M) cable as supported.
So I have two questions. First is if the 10 meter cable will work and second has anyone run into any issues linking the 3850's to Dell switches via 10GB.

I think I answered my first question. Doing a bit more digging I found the "Cisco 10-Gigabit Ethernet Transceiver Modules Compatibility Matrix" which shows the SFP-H10GB-ACU10M is supported on the 3850 with OS XE 3.6.0E installed.
Still would like to know of anyone linking the 3850 to the 8132F however...

Sfp-h10gb-acu10m compatibility

Similar Messages

Maybe you are looking for