SFP-H10GB-CU1M SFP+ Copper Cable module speed shows as Unknown

I have connected 2 SG500x switches using an SFP-H10GB-CU1M SFP+ Copper Cable module.  Since the port shows as a 10G port, I would expect the speed to show as 10G as well.  However, it shows as "Unknown".  This doesn't leave me with confidence that it is being recognized properly.  The link is working properly, but I haven't run tests to verify if I'm getting full 10G throughput or not.  I'll work on that.  In the meantime, anyone have any ideas as to the proper behavior here?  Shouldn't it show 10G as the link speed?

Hi Robert,
I love the GUI, so easy to navigate, when you get the feel for the layout of the switch options. So going to ask you to use the GUI to find the stacking status and  speed between the switches..
Step 1.  Select help at the top right of the GUI screen, 
Step 2.  Type in as a search option "stack speed " then clock go
see my screen capture below,.
( The switch has basically an Administration guide built in., a really cool cool feature  ) 
So you see the following screen capture that shows the option that I selected;
Followed the instruction outlines in the online help text,  the following screen capture shows me the stacking speed.,
I have two by SG500-52P, my SG500X are loaned out to a partner to evaluate,   so i can only run 5G over the SFP-H10GB-CU1M  stacking module on this platform.
Hope this helps you clarify where to find stack module speed.
regards Dave
Rate this post

Similar Messages

  • 4500x VSS and SFP-H10GB-CU1M

    Hello
    I have (2) Cisco 4500x with a VSS config. I als have a couple cables "SFP-H10GB-CU1M".
    I want to make sure I have this physically setup correctly. I have searched but not found anything specific enough.
    Please review and advise.

    Yes, all device packages are installed (including 7.0) and the Pi 2.1.2 patch.
    Info from "ifm_config_archive.log" when trying Archive the Configuration:
    [2014-12-09 19:58:11,300] [pool-37-thread-5] [service] [ERROR] - Thread Id : [9,460] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching VLAN file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]'
    Maybe the Prime don't know where to find the vlan.dat on the 4500X-VSS ?
    #dir cat4000_flash:
    Directory of cat4000_flash:/
        1  -rw-        2236                    <no date>  vlan.dat
    sysObjectID (1.3.6.1.2.1.1.2)  is
    .iso.org.dod.internet.private.enterprises.cisco.ciscoProducts.cat4xxxVirtualSwitch 
    That is not the expected and supported value  "4500X-16"  above
    Update: Error on fetching running and startup config as well:
    [2014-12-09 20:24:21,818] [pool-37-thread-9] [service] [ERROR] - Thread Id : [10,013] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching RUNNINGCONFIG file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]
    [2014-12-09 20:25:31,882] [pool-37-thread-9] [service] [ERROR] - Thread Id : [10,013] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching STARTUPCONFIG file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]

  • Connecting Nexus 2232PP-10GE to a Qlogic 10Gb CNA for IBM System X using PROSFP's SFP-H10GB-ACU7M cable

    The cisco nexus interface is only detecting the type as
    SFP-H10GB-CU1M, instead of  SFP-H10GB-ACU7M. Is the PROSFP transceiver and cable supported by Cisco's Nexus? Is this a supported connection?
    Thanks....

  • Cat6807 + VS-S2T-10G + CVR-X2-SFP10G + SFP-H10GB-CU5M?

    Is the Cisco OneXConverter Module, CVR-X2-SFP10G, compatible with VS-S2T-10G in a 6807 using a SFP-H10GB-CU5M cable to connect to an ASA5585?
    Description of the CVR-X2-SFP10G, which states it is compatible with the SFP-H10GB-CU5M:
    http://www.cisco.com/en/US/prod/collateral/modules/ps5455/data_sheet_c78-547521.html
    Compatibility matrix which eludes the CVR-X2-SFP10G module is compatible with the VS-S2T-10G and SFP-H10GB-CU5M but only if the SFP-H10GB-CU5M is version 2.  I am not comfortable with this chart as it does not list the software requirement which could imply it is not compatible when used with the SFP-H10GB-CU5M.
    http://www.cisco.com/en/US/partner/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6974.html
    snippit of chart:
    Platform
    Switch or Module
    Transceiver Model
    Minimum Software Release Required
    VS-S2T-10G
    VS-S2T-10G-XL
    WS-X6816-10G-2T
    WS-X6816-10G-2TXL
    WS-X6908-10G-2T
    WS-X6908-10G-2TXL
    (With CVR-X2-SFP10G converter for X2 ports)
    SFP-H10GB-CU1M1
    SFP-H10GB-CU3M1
    SFP-H10GB-CU5M1
    SFP-10G-SR
    SFP-10G-LRM
    SFP-10G-LR
    12.2(50)SY
    12.2(50)SY
    1 Only Version -02 or later is supported.

    Hello teater,
    SFP-H10GB-CU5M1 is supported with Sup2T and CVR-X2-SFP10G starting 12.2(50)SY.
    I will look into fixing the compatibility matrix to fill this missing cell.
    Thanks,
    ~Amer

  • HP DAC Copper Cable with Cisco 4900M

    We have HP C7000/VC-Flex 10 Module  that I would like to connect to our Netapps NFS datastore.  The Cisco  switch that I will be using between HP Flex-10 and Netapps is Cisco  4900M.  I have a HP cable AP784A direct attach copper SFP+ to SFP+.   Which module I need to purchase and insert into my 4900M to support 10Gb  connectivity via HP DAC 10Gb cable.
    Please Advise!

    You need
    4900M 4 port 10GE half card with X2 interfaces (WS-X4904-10GE)
        OR
    4900M 8 port 10GE half card with X2 interfaces (WS-X4908-10GE)
    WITH
    Cisco OneX Converter Module Converts an X2 Interface into One SFP+ Interface (CVR-X2-SFP10G)
    I would recommend you to use following DAC cables from Cisco.
    • SFP-H10GB-CU1M: 10GBASE-CU SFP+ Cable 1 meter (Version -02)
    • SFP-H10GB-CU3M: 10GBASE-CU SFP+ Cable 3 meter (Version -02)
    • SFP-H10GB-CU5M: 10GBASE-CU SFP+ Cable 5 meter (Version -02)

  • Compatibility between ASR9K and SFP-H10GB-ACU10M

    Hi Everyone,
    I have in my environment two ASR9K with module A9K-16T/8-B and I am trying to connect using the Active Twinax cable 10M (SFP-H10GB-ACU10M), however when I connected the cable, shows the following error:
    State:
        Administrative state: enabled
        Operational state: Down (Reason: Security failure (not a valid part))
        LED state: Red On
    Phy:
        Media type: Not known
        Optics:
            Vendor: CISCO-TYCO
            Part number: 2163675-2
            Serial number: TED1618U0H0
    I checked the compatibility list and apparently okay, as shown in the link below:
    http://www.cisco.com/c/en/us/products/collateral/routers/asr-9000-series-aggregation-services-routers/data_sheet_c78-624747.html
    Please, the community can help me?
    Best Regards,
    Vitor Nakano

    The twinax copper 10 Gig SFPs such as the one you cite are prefabricated cables with transceivers already attached. See the pictures on the top left of the data sheet to visualize what you get.
    Controlling that mating of transceiver to the copper media is how they are able to ensure reliable operation at 10 Gbps over copper.

  • SFP-H10GB-ACU10M

    Dear All,
    does  SFP-H10GB-ACU10M come with SFP+ connectors?
    or it is just a cable and we need to provide the SFP+ Transceivers??
    thanks

    The twinax copper 10 Gig SFPs such as the one you cite are prefabricated cables with transceivers already attached. See the pictures on the top left of the data sheet to visualize what you get.
    Controlling that mating of transceiver to the copper media is how they are able to ensure reliable operation at 10 Gbps over copper.

  • Sfp-h10gb-acu10m compatibility

                       Dear all,
    Does anybody know if  SFP-H10GB-ACU10M cable is compatible with Cisco Catalyst 2960-S series? According to the compatibility matrix it is not compatible with Cisco IOS release 12.2 (53) SE1, but i would like to know if it would be compatible with another IOS version.
    Thanks in advance,
    Carmen

    I suspect it might have something to do with the CVR-X2-SFP10G, seeing that the converter module data sheet also does not list any length of the Active Twinax cables being compatible.
    I am trying to reach out to someone within the Product Mgmt org to see if they can provide an answer... but my contacts are old....

  • N5K:does active Twinax SFP-H10GB-ACU7M support FCoE

    Hi
    does SFP-H10GB-ACU7M and SFP-H10GB-ACU10M support FCoE if they are used in Nexus5000 running 5.0.3
    I heard rumors thats it could be that these active Twinax do not support FCoe because they could net reach the BER which is necessary for FCoE
    KR
    Hubert

    Hubert,
    They're in the compatibility matrix but only show being supported by NX-OS 4.2(1)N2(1)
    http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6974.html
    I don't know about the Bit Error Rate though.  The fact that they're supported in 4.2.1 but not in 5.x makes me think its a testing thing rather than a functional BER thing.  I could be wrong on that though.  Short answer is not supported.
    --Justin

  • SFP-H10GB-CU5M and HP NICs

    Hello,
    Can anyone confirm that SFP-H10GB-CU5M can work with HP NICs (HP Ethernet 10Gb 2-port 530FLR-SFP+ Adapter, or modifications on same chipset) ?

    Hello teater,
    SFP-H10GB-CU5M1 is supported with Sup2T and CVR-X2-SFP10G starting 12.2(50)SY.
    I will look into fixing the compatibility matrix to fill this missing cell.
    Thanks,
    ~Amer

  • Can use SFP-H10GB-CU3M to connect 6120XP to Cat6K Switch?

    Can use SFP-H10GB-CU3M OR SFP-H10GB-CU5M to connect 6120XP to Cat6K Switch?

    You dont have to connect to Nexus equipment. Your LAN can be anything as long as you can connect the UCS system to it.
    Currently you need a switch with 10GE ports to uplink from your 6100s.
    I believe that in the next version of the firmware/software in UCS you will be able to connect your 6100s to the LAN using 1G ports.
    Nuno Ferreira

  • Copper cable / GigE Copper Interface as Private Interconnect for Oracle RAC

    Hello Gurus
    Can some one confirm if the copper Cables ( Cat5/RJ45) can be used for Gig Ethernet i.e. Private interconnects for deploying Oracle RAC 9.x or 10gR2 on Solaris 9/10 .
    i am planning to use 2 X GigE Interfaces (one port each from X4445 Quad Port Ethernet Adapters) & Planning to connect it using copper cables ( all the documents that i came across is been refering to the fiber cables for Private Interconnects , connecting GigE Interfaces , so i am getting bit confused )
    would appretiate if some one can throw some lights on the same.
    regards,
    Nilesh Naik
    thanks

    Cat5/RJ45 can be used for Gig Ethernet Private interconnects for Oracle RAC. I would recommend trunking the two or more interconnects for redundancy. The X4445 adapters are compatible with the Sun Trunking 1.3 software (http://www.sun.com/products/networking/ethernet/suntrunking/). If you have servers that support the Nemo framework (bge, e1000g, xge, nge, rge, ixgb), you can use the Solaris 10 trunking software, dladmin.
    We have a couple of SUN T2000 servers and are using the onboard GigE ports for the Oracle 10gR2 RAC interconnects. We upgraded the onboard NIC drivers to the e1000g and used the Solaris 10 trunking software. The next update of Solaris will have the e1000g drivers as the default for the SUN T2000 servers.

  • Stolen the copper cable and you haven't finished y...

    So as title suggests, we had a perfectly connecting broadband (still under 1 mb) but still it worked. Then "someone" stole all the copper cable leading to our village, leaving us without phone and internet for 2 weeks! untill you "repaired the problem".
    as a result of your repairs our perfectly working router suddenly stopped working and we had to go back to using the BT supplied HomeHub (1.0) which was an abortion by the way, we have now upgraded our whole system at our expense ofc and are now connected to the internet. But we still have ping of between 300 -600!! most of the programs on your computer dont know how to deal with that sort of dodgy connection and just say "no connection" etc.
    So how have you completed your repairs if the connection is worse than the pretty lowsy connection before?
    Why did you not while repairing the cabling, put in some of the new fibre optic "infinity" that we were supposed to have got a month ago?
    and no i would rather not call one of your foreign call centres where they just tell you to turn it off and turn it on again, we have been loyal customers for around 6 years, but your forcing us towards going else where.
    I look forward to any feedback,
    Bobby

    thanks with the quick response:
    UPSTAIRS
    Pinging www.bbc.net.uk [212.58.246.90] with 32 bytes of data:
    Reply from 212.58.246.90: bytes=32 time=360ms TTL=51
    Reply from 212.58.246.90: bytes=32 time=413ms TTL=51
    Reply from 212.58.246.90: bytes=32 time=440ms TTL=51
    Reply from 212.58.246.90: bytes=32 time=350ms TTL=51
    Ping statistics for 212.58.246.90:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
    Approximate round trip times in milli-seconds:
    Minimum = 350ms, Maximum = 440ms, Average = 390ms
    Pinging 192.168.2.1 with 32 bytes of data:
    Reply from 192.168.2.1: bytes=32 time=2ms TTL=64
    Reply from 192.168.2.1: bytes=32 time=2ms TTL=64
    Reply from 192.168.2.1: bytes=32 time=3ms TTL=64
    Reply from 192.168.2.1: bytes=32 time=3ms TTL=64
    Ping statistics for 192.168.2.1:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
    Approximate round trip times in milli-seconds:
    Minimum = 2ms, Maximum = 3ms, Average = 2ms
    DOWNSTAIRS
    Pinging www.bbc.net.uk [212.58.244.69] with 32 bytes of data:
    Reply from 212.58.244.69: bytes=32 time=351ms TTL=51
    Reply from 212.58.244.69: bytes=32 time=404ms TTL=51
    Reply from 212.58.244.69: bytes=32 time=459ms TTL=51
    Reply from 212.58.244.69: bytes=32 time=484ms TTL=51
    Ping statistics for 212.58.244.69:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
    Approximate round trip times in milli-seconds:
    Minimum = 351ms, Maximum = 484ms, Average = 424ms
    Pinging 192.168.2.1 with 32 bytes of data:
    Reply from 192.168.2.1: bytes=32 time<1ms TTL=64
    Reply from 192.168.2.1: bytes=32 time<1ms TTL=64
    Reply from 192.168.2.1: bytes=32 time<1ms TTL=64
    Reply from 192.168.2.1: bytes=32 time<1ms TTL=64
    Ping statistics for 192.168.2.1:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
    Approximate round trip times in milli-seconds:
    Minimum = 0ms, Maximum = 0ms, Average = 0ms

  • Cannot display the screen of the macbook on TV. OS is Lion 10.7.2. Connection to the TV is over HDMI cable.  TV shows only the backgroud picture of Lion. Do you have any suggestions for help ?

    Cannot display the screen of my macbook on TV. OS is Lion 10.7.2. The Macbook is connected to the TV is over HDMI cable.  TV shows only the backgroud picture of the Lion OS and reacts even to mission control. Do you have any suggestions for help ?

    You have the display set in Extended Desktop mode. In System Preferences>Display on the MacBook screen there should be an Arrangement tab when you have the MacBook hooked up to the TV and both screens working. When you click the Arrangement tab do you see two monitors side by side? One of them will have a Menu Bar at the top. Just click on the Menu Bar and drag it to the second monitor. That will make the second monitor your main screen. You can now use your MacBook in Clamshell Mode with a wired or Bluetooth keyboard and mouse.  http://support.apple.com/kb/HT3131 When you disconnect from the TV your Menu Bar will automatically change back to the MacBook.
    Or if you want to work on the MacBook screen while showing it on a TV you can check the Mirror Display box on the lower left hand side of the Arrangement tab under the two monitors box.

  • Playbook only works with charger or USB cable despite batter showing 100% charge

    After 2 years of faithful service, playbook only works with charger or USB cable despite batter showing 100% charge. As soon as the cable/charger is unplugged, it just switches off. When cable is plugged in again, and start button pressed, it reboots. I have reinstalled sftwer from scrathc via Desktop Manager, but the problem persists. I saw this problem raised in the fora several times, but never any explanation why it happens. Any ideas?
    Solved!
    Go to Solution.

    A high resistance between battery lead and motherboard would allow trickle charge but not power discharge.
    If you want to risk it, prise off the back of the playbook using an old credit card, locate the two screws holding on the battery lead, remove, clean up, then replace.  replace back carefully as the antennae connectors are pressure pads.
    Sarah.

Maybe you are looking for