Sfp issue to connect to cisco 2960
We bought two Cisco 2960-48TC-L, I have issue with gi0/1 and 0/2. the sfp won't stick into the port firmly, you have to press the it in order to get the light,try with second 2960, the same result, yet, tried some other 2960 we got few month ago, it works fine, by the way, these 2 cisco 2960 made in Oct,08, I suspect the gi0/1 and 0/2 is defective, anyone has any suggestion?
Once you insert the SFP's the switches should detect and can be seen from the sh int status command
If they are not detecting, then i would suggest you raise a case with cisco and get RMA
Narayan
Similar Messages
-
Printer Reboots at 75% when connected to Cisco 2960
Currently Being Moderated
Xerox 5745 Printer Reboots at 75% when connected to Cisco 2960
Hi,
We are having a problem with our Xerox 5745 multifunction Printer...
This problem had been forwarded to Xerox, but they claim that a problem was caused by a power surge on our Cisco router.
We are having a total of 8 CiscoCatalyst 2960 Series in our IT Communication rooms.
We are also having 2 Xerox 7120, 4 Xerox 5745, 6 HP5200 and 300 computers - PC (HP Desktop) and Laptop (Samsung).
Network : all connected to CISCO Catalyst 2960 Series
Printer Setup:
IP Address: Manual IP Assignment (DHCP Disabled)
PC Setup: TCP/IP –RAW on Port 9100 – SNMP Status ENABLED
The two machines has same firmware software and configuration settings.
one machine just been installed with latest firmware
Problem:
On 3 Xerox 5745 display panel shows: "Network Controller booting"
at 75% the system restart and go on again and again.
This happens when cables are connected to CISCO Catalyst 2660.
Testing done:
•1. No problem, Connecting directly to laptop using (crossover cable), accesss to printing is normal.
•2. No Problem, Using other switch - dLink (not CISCO Catalyst 2960), the printing is normal.
•3. Not work, changing ip address; disabling all protocol; changing speed to 10MBps.
•4. Not work, Switching to other port on CISCO Catalyst 2960.
•5. Not work, Re-starting the Cisco Catalyst 2960 s.
•6. Not work, Changing cables.
HELP! Please ...Ferdinand,
at least you're not the only one who's experiencing this problem:
http://forum.support.xerox.com/t5/Hardware/Workcentre-5135-network-controller/td-p/5086
http://www.fixya.com/support/t556616-network_controller_unavailable (read the comments too!)
In case of your c2960 supports PoE, did you test to disable power inline (I know, PoE normally can't be the reason - but this is a really strange problem)?
What happens when you boot a printer without network connectivity (or with the dLink) to 100% and connect it after that to the c2960 switch? -
Alteon Switch to Cisco 2960 port aggrigating
LACP / 802.3ad is required to aggrigate a cisco to a non cisco switch, is there any issues connecting a Cisco 2960 to a Alteon Switch.
There should be none as long as alteon support LaCP, 2960 certainly do. for configuration guide info, have a look at the following:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat2960/12225see/scg/swethchl.htm
Please rate all posts. -
Cisco 2960S-24TS-S using SFP modules between switches
I am using Cisco 2960S-24TS-S using SFP modules for two different speed requirements, I have two SFP ports using 100Mbit modules and the other two SFP ports using 1000Mbit modules.
I have two Cisco 2960S-24TS-S switches connected together via a fiber optic cable, and each SFP module is on port 28, with a 1000 Mbit SFP module in each, and the two switches will not connect. The fiber was checked with a light tester not a db kit.
Do I need to have SFP port specific setup details in a configuration file for the Cisco Switch or does the SFP module handle this?
" interface GigabitEthernet1/0/28" - set up in config file for the port. Does this need to dictate "interface 100" or "1000MbitEthernet1/0/28" instead?The ports should auto-negotiate speed you should not need to hard code them to get them to come up , Are the ports showing up/down or down/down can you post the show interface for each side and the show run int x/x for each port
-
IEEE 802.1x with EAP-TLS issue in cisco 2960
In My Cisco 2960 switch is not working with EAP-TLS mechanism of 802.1x but its works well with other protocols like EAP-PEAP or MAC Address authentication.
Below is the configuration
aaa authentication login default group tacacs+ local
aaa authentication enable default group tacacs+ enable
aaa authentication dot1x default group radius
aaa authorization commands 15 default group tacacs+ local
aaa authorization network default group radius
aaa authorization configuration default group radius
aaa accounting update periodic 30
aaa accounting dot1x default start-stop group radius
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 0 default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa accounting network default start-stop group tacacs+
aaa accounting connection default start-stop group tacacs+
aaa accounting system default start-stop group tacacs+
interface FastEthernet0/1
switchport access vlan 11
switchport mode access
speed 100
duplex full
authentication order dot1x mab webauth
authentication port-control auto
mab
dot1x pae authenticator
dot1x timeout tx-period 3
dot1x timeout supp-timeout 3
spanning-tree portfast
spanning-tree bpduguard enable
Can anyone suggest me ?Thanks for the reply jatin.
I have a client on the interface fa0/1 with a valid client certificate. And have a debug logs as below
*Mar 8 00:03:06.266: dot1x-ev(Fa0/1): Interface state changed to UP
*Mar 8 00:03:06.266: AAA/BIND(000001C7): Bind i/f
*Mar 8 00:03:06.266: dot1x_auth Fa0/1: initial state auth_initialize has enter
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_initialize_enter called
*Mar 8 00:03:06.266: dot1x_auth Fa0/1: during state auth_initialize, got event 0(cfg_auto)
*Mar 8 00:03:06.266: @@@ dot1x_auth Fa0/1: auth_initialize -> auth_disconnected
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_disconnected_enter called
*Mar 8 00:03:06.266: dot1x_auth Fa0/1: idle during state auth_disconnected
*Mar 8 00:03:06.266: @@@ dot1x_auth Fa0/1: auth_disconnected -> auth_restart
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_enter called
*Mar 8 00:03:06.266: dot1x-ev(Fa0/1): Sending create new context event to EAP for 0xB0000DBA (0000.0000.0000)
*Mar 8 00:03:06.266: dot1x_auth_bend Fa0/1: initial state auth_bend_initialize has enter
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_initialize_enter called
*Mar 8 00:03:06.266: dot1x_auth_bend Fa0/1: initial state auth_bend_initialize has idle
*Mar 8 00:03:06.266: dot1x_auth_bend Fa0/1: during state auth_bend_initialize, got event 16383(idle)
*Mar 8 00:03:06.266: @@@ dot1x_auth_bend Fa0/1: auth_bend_initialize -> auth_bend_idle
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_enter called
*Mar 8 00:03:06.266: dot1x-ev(Fa0/1): Created a client entry (0xB0000DBA)
*Mar 8 00:03:06.266: dot1x-ev(Fa0/1): Dot1x authentication started for 0xB0000DBA (0000.0000.0000)
*Mar 8 00:03:06.266: dot1x-ev:DOT1X Supplicant not enabled on FastEthernet0/1
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): Posting !EAP_RESTART on Client 0xB0000DBA
*Mar 8 00:03:06.266: dot1x_auth Fa0/1: during state auth_restart, got event 6(no_eapRestart)
*Mar 8 00:03:06.266: @@@ dot1x_auth Fa0/1: auth_restart -> auth_connecting
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_enter called
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_connecting_action called
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): Posting RX_REQ on Client 0xB0000DBA
*Mar 8 00:03:06.274: dot1x_auth Fa0/1: during state auth_connecting, got event 10(eapReq_no_reAuthMax)
*Mar 8 00:03:06.274: @@@ dot1x_auth Fa0/1: auth_connecting -> auth_authenticating
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authenticating_enter called
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_authenticating_action called
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): Posting AUTH_START for 0xB0000DBA
*Mar 8 00:03:06.274: dot1x_auth_bend Fa0/1: during state auth_bend_idle, got event 4(eapReq_authStart)
*Mar 8 00:03:06.274: @@@ dot1x_auth_bend Fa0/1: auth_bend_idle -> auth_bend_request
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
*Mar 8 00:03:06.274: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:06.274: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:06.274: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:06.274: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:06.274: EAPOL pak dump Tx
*Mar 8 00:03:06.274: EAPOL Version: 0x3 type: 0x0 length: 0x0005
*Mar 8 00:03:06.274: EAP code: 0x1 id: 0x1 length: 0x0005 type: 0x1
*Mar 8 00:03:06.274: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (0000.0000.0000)
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_request_action called
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:06.794: dot1x-packet(Fa0/1): queuing an EAPOL pkt on Auth Q
*Mar 8 00:03:06.794: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
*Mar 8 00:03:06.794: EAPOL pak dump rx
*Mar 8 00:03:06.794: EAPOL Version: 0x1 type: 0x1 length: 0x0000
*Mar 8 00:03:06.794: dot1x-ev:
dot1x_auth_queue_event: Int Fa0/1 CODE= 0,TYPE= 0,LEN= 0
*Mar 8 00:03:06.794: dot1x-packet(Fa0/1): Received an EAPOL frame
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): Received pkt saddr =d43d.7e65.4fc1 , daddr = 0180.c200.0003,
pae-ether-type = 888e.0101.0000
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): Couldn't find the supplicant in the list
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): New client detected, notifying AuthMgr
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): Sending event (0) to Auth Mgr for d43d.7e65.4fc1
*Mar 8 00:03:06.794: dot1x-packet(Fa0/1): Received an EAPOL-Start packet
*Mar 8 00:03:06.794: EAPOL pak dump rx
*Mar 8 00:03:06.794: EAPOL Version: 0x1 type: 0x1 length: 0x0000
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): Posting EAPOL_START on Client 0xB0000DBA
*Mar 8 00:03:06.794: dot1x_auth Fa0/1: during state auth_authenticating, got event 4(eapolStart)
*Mar 8 00:03:06.794: @@@ dot1x_auth Fa0/1: auth_authenticating -> auth_aborting
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authenticating_exit called
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_aborting_enter called
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): 802.1x method gets the go ahead from Auth Mgr for 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.794: %AUTHMGR-5-START: Starting 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EE240F5BAB
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): Posting AUTH_ABORT for 0xB0000DBA
*Mar 8 00:03:06.794: dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 1(authAbort)
*Mar 8 00:03:06.794: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_initialize
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_initialize_enter called
*Mar 8 00:03:06.794: dot1x_auth_bend Fa0/1: idle during state auth_bend_initialize
*Mar 8 00:03:06.794: @@@ dot1x_auth_bend Fa0/1: auth_bend_initialize -> auth_bend_idle
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_enter called
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): Posting !AUTH_ABORT on Client 0xB0000DBA
*Mar 8 00:03:06.794: dot1x_auth Fa0/1: during state auth_aborting, got event 20(no_eapolLogoff_no_authAbort)
*Mar 8 00:03:06.794: @@@ dot1x_auth Fa0/1: auth_aborting -> auth_restart
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_aborting_exit called
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_enter called
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): Resetting the client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): Sending create new context event to EAP for 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.802: dot1x-sm(Fa0/1): 0xB0000DBA:auth_aborting_restart_action called
*Mar 8 00:03:06.802: dot1x-sm(Fa0/1): Posting !EAP_RESTART on Client 0xB0000DBA
*Mar 8 00:03:06.802: dot1x_auth Fa0/1: during state auth_restart, got event 6(no_eapRestart)
*Mar 8 00:03:06.802: @@@ dot1x_auth Fa0/1: auth_restart -> auth_connecting
*Mar 8 00:03:06.802: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_enter called
*Mar 8 00:03:06.802: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_connecting_action called
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): Posting RX_REQ on Client 0xB0000DBA
*Mar 8 00:03:06.811: dot1x_auth Fa0/1: during state auth_connecting, got event 10(eapReq_no_reAuthMax)
*Mar 8 00:03:06.811: @@@ dot1x_auth Fa0/1: auth_connecting -> auth_authenticating
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authenticating_enter called
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_authenticating_action called
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): Posting AUTH_START for 0xB0000DBA
*Mar 8 00:03:06.811: dot1x_auth_bend Fa0/1: during state auth_bend_idle, got event 4(eapReq_authStart)
*Mar 8 00:03:06.811: @@@ dot1x_auth_bend Fa0/1: auth_bend_idle -> auth_bend_request
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
*Mar 8 00:03:06.811: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:06.811: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:06.811: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:06.811: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:06.811: EAPOL pak dump Tx
*Mar 8 00:03:06.811: EAPOL Version: 0x3 type: 0x0 length: 0x0005
*Mar 8 00:03:06.811: EAP code: 0x1 id: 0x1 length: 0x0005 type: 0x1
*Mar 8 00:03:06.811: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_request_action called
*Mar 8 00:03:06.811: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:06.811: dot1x-packet(Fa0/1): Queuing an EAPOL pkt on Authenticator Q
*Mar 8 00:03:06.811: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
*Mar 8 00:03:06.811: EAPOL pak dump rx
*Mar 8 00:03:06.811: EAPOL Version: 0x1 type: 0x0 length: 0x0022
*Mar 8 00:03:06.811: dot1x-ev:
dot1x_auth_queue_event: Int Fa0/1 CODE= 2,TYPE= 1,LEN= 34
*Mar 8 00:03:06.811: dot1x-packet(Fa0/1): Received an EAPOL frame
*Mar 8 00:03:06.811: dot1x-ev(Fa0/1): Received pkt saddr =d43d.7e65.4fc1 , daddr = 0180.c200.0003,
pae-ether-type = 888e.0100.0022
*Mar 8 00:03:06.811: dot1x-packet(Fa0/1): Received an EAP packet
*Mar 8 00:03:06.811: EAPOL pak dump rx
*Mar 8 00:03:06.811: EAPOL Version: 0x1 type: 0x0 length: 0x0022
*Mar 8 00:03:06.811: dot1x-packet(Fa0/1): Received an EAP packet from d43d.7e65.4fc1
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): Posting EAPOL_EAP for 0xB0000DBA
*Mar 8 00:03:06.811: dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 6(eapolEap)
*Mar 8 00:03:06.811: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_response
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_enter called
*Mar 8 00:03:06.811: dot1x-ev(Fa0/1): dot1x_sendRespToServer: Response sent to the server from 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_response_action called
*Mar 8 00:03:06.811: AAA/AUTHEN/8021X (000001C7): Pick method list 'default'
*Mar 8 00:03:06.819: RADIUS/ENCODE(000001C7):Orig. component type = DOT1X
*Mar 8 00:03:06.819: RADIUS(000001C7): Config NAS IP: 0.0.0.0
*Mar 8 00:03:06.819: RADIUS/ENCODE(000001C7): acct_session_id: 724
*Mar 8 00:03:06.819: RADIUS(000001C7): sending
*Mar 8 00:03:06.819: RADIUS/ENCODE: Best Local IP-Address 10.26.237.11 for Radius-Server 10.26.13.59
*Mar 8 00:03:06.819: RADIUS(000001C7): Send Access-Request to 10.26.13.59:1812 id 1645/83, len 251
*Mar 8 00:03:06.819: RADIUS: authenticator A1 79 FA E5 F4 B7 7F 4F - 2B 73 3A 0D 1F D8 89 20
*Mar 8 00:03:06.819: RADIUS: User-Name [1] 31 "host/D0902MALL005.IN.intranet"
*Mar 8 00:03:06.819: RADIUS: Service-Type [6] 6 Framed [2]
*Mar 8 00:03:06.819: RADIUS: Framed-MTU [12] 6 1500
*Mar 8 00:03:06.819: RADIUS: Called-Station-Id [30] 19 "D4-A0-2A-EE-14-81"
*Mar 8 00:03:06.819: RADIUS: Calling-Station-Id [31] 19 "D4-3D-7E-65-4F-C1"
*Mar 8 00:03:06.819: RADIUS: EAP-Message [79] 36
*Mar 8 00:03:06.819: RADIUS: 02 01 00 22 01 68 6F 73 74 2F 44 30 39 30 32 4D 41 4C 4C 30 ["host/D0902MALL0]
*Mar 8 00:03:06.819: RADIUS: 30 35 2E 49 4E 2E 69 6E 74 72 61 6E 65 74 [ 05.IN.intranet]
*Mar 8 00:03:06.819: RADIUS: Message-Authenticato[80] 18
*Mar 8 00:03:06.819: RADIUS: D6 6F 7B CD 36 46 5E F6 90 6F 85 A8 BD BD AE D8 [ o{6F^o]
*Mar 8 00:03:06.819: RADIUS: EAP-Key-Name [102] 2 *
*Mar 8 00:03:06.819: RADIUS: Vendor, Cisco [26] 49
*Mar 8 00:03:06.819: RADIUS: Cisco AVpair [1] 43 "audit-session-id=0A1AED0B000000EE240F5BAB"
*Mar 8 00:03:06.819: RADIUS: NAS-Port-Type [61] 6 Ethernet [15]
*Mar 8 00:03:06.819: RADIUS: NAS-Port [5] 6 50001
*Mar 8 00:03:06.819: RADIUS: NAS-Port-Id [87] 17 "FastEthernet0/1"
*Mar 8 00:03:06.819: RADIUS: NAS-IP-Address [4] 6 10.26.237.11
*Mar 8 00:03:06.819: RADIUS: Acct-Session-Id [44] 10 "000002D4"
*Mar 8 00:03:06.819: RADIUS(000001C7): Started 3 sec timeout
*Mar 8 00:03:06.861: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Mar 8 00:03:06.903: RADIUS: Received from id 1645/83 10.26.13.59:1812, Access-Challenge, len 76
*Mar 8 00:03:06.903: RADIUS: authenticator 7B 1C DC CA A8 92 E9 34 - 17 86 25 2F 9D 7E 63 96
*Mar 8 00:03:06.903: RADIUS: EAP-Message [79] 8
*Mar 8 00:03:06.903: RADIUS: 01 02 00 06 0D 20 [ ]
*Mar 8 00:03:06.903: RADIUS: Message-Authenticato[80] 18
*Mar 8 00:03:06.903: RADIUS: DD F3 7B 33 37 6D 40 BD F3 D2 78 DF F1 14 4D E4 [ {37m@xM]
*Mar 8 00:03:06.903: RADIUS: State [24] 30
*Mar 8 00:03:06.903: RADIUS: 00 7D 00 9B 00 C1 00 40 ED B8 45 00 FC DD 50 2E DC 0E E6 03 FC 7B AD 4C B7 E7 B1 70 [ }@EP.{Lp]
*Mar 8 00:03:06.911: RADIUS(000001C7): Received from id 1645/83
*Mar 8 00:03:06.911: RADIUS/DECODE: EAP-Message fragments, 6, total 6 bytes
*Mar 8 00:03:06.911: dot1x-sm(Fa0/1): Posting EAP_REQ for 0xB0000DBA
*Mar 8 00:03:06.911: dot1x_auth_bend Fa0/1: during state auth_bend_response, got event 7(eapReq)
*Mar 8 00:03:06.911: @@@ dot1x_auth_bend Fa0/1: auth_bend_response -> auth_bend_request
*Mar 8 00:03:06.911: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_exit called
*Mar 8 00:03:06.911: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
*Mar 8 00:03:06.911: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:06.911: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:06.911: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:06.911: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:06.911: EAPOL pak dump Tx
*Mar 8 00:03:06.911: EAPOL Version: 0x3 type: 0x0 length: 0x0006
*Mar 8 00:03:06.911: EAP code: 0x1 id: 0x2 length: 0x0006 type: 0xD
*Mar 8 00:03:06.911: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.911: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_request_action called
*Mar 8 00:03:06.920: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:06.920: dot1x-packet(Fa0/1): Queuing an EAPOL pkt on Authenticator Q
*Mar 8 00:03:06.920: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
*Mar 8 00:03:06.920: EAPOL pak dump rx
*Mar 8 00:03:06.920: EAPOL Version: 0x1 type: 0x0 length: 0x0069
*Mar 8 00:03:06.920: dot1x-ev:
dot1x_auth_queue_event: Int Fa0/1 CODE= 2,TYPE= 13,LEN= 105
*Mar 8 00:03:06.920: dot1x-packet(Fa0/1): Received an EAPOL frame
*Mar 8 00:03:06.920: dot1x-ev(Fa0/1): Received pkt saddr =d43d.7e65.4fc1 , daddr = 0180.c200.0003,
pae-ether-type = 888e.0100.0069
*Mar 8 00:03:06.920: dot1x-packet(Fa0/1): Received an EAP packet
*Mar 8 00:03:06.920: EAPOL pak dump rx
*Mar 8 00:03:06.920: EAPOL Version: 0x1 type: 0x0 length: 0x0069
*Mar 8 00:03:06.920: dot1x-packet(Fa0/1): Received an EAP packet from d43d.7e65.4fc1
*Mar 8 00:03:06.920: dot1x-sm(Fa0/1): Posting EAPOL_EAP for 0xB0000DBA
*Mar 8 00:03:06.920: dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 6(eapolEap)
*Mar 8 00:03:06.920: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_response
*Mar 8 00:03:06.920: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_enter called
*Mar 8 00:03:06.920: dot1x-ev(Fa0/1): dot1x_sendRespToServer: Response sent to the server from 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.920: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_response_action called
*Mar 8 00:03:06.920: AAA/AUTHEN/8021X (000001C7): Pick method list 'default'
*Mar 8 00:03:06.920: RADIUS/ENCODE(000001C7):Orig. component type = DOT1X
*Mar 8 00:03:06.920: RADIUS(000001C7): Config NAS IP: 0.0.0.0
*Mar 8 00:03:06.920: RADIUS/ENCODE(000001C7): acct_session_id: 724
*Mar 8 00:03:06.920: RADIUS(000001C7): sending
*Mar 8 00:03:06.920: RADIUS/ENCODE: Best Local IP-Address 10.26.237.11 for Radius-Server 10.26.13.59
*Mar 8 00:03:06.920: RADIUS(000001C7): Send Access-Request to 10.26.13.59:1812 id 1645/84, len 352
*Mar 8 00:03:06.920: RADIUS: authenticator 41 72 8D 6A B4 72 19 84 - 1B C8 33 F7 95 DD 07 BC
*Mar 8 00:03:06.928: RADIUS: User-Name [1] 31 "host/D0902MALL005.IN.intranet"
*Mar 8 00:03:06.928: RADIUS: Service-Type [6] 6 Framed [2]
*Mar 8 00:03:06.928: RADIUS: Framed-MTU [12] 6 1500
*Mar 8 00:03:06.928: RADIUS: Called-Station-Id [30] 19 "D4-A0-2A-EE-14-81"
*Mar 8 00:03:06.928: RADIUS: Calling-Station-Id [31] 19 "D4-3D-7E-65-4F-C1"
*Mar 8 00:03:06.928: RADIUS: EAP-Message [79] 107
*Mar 8 00:03:06.928: RADIUS: 02 02 00 69 0D 80 00 00 00 5F 16 03 01 00 5A 01 00 00 56 03 01 52 C5 45 4F 07 CA B3 29 50 A7 CE 40 76 B6 BD F0 50 D4 CE 9A 8A 02 C4 3D 40 35 B5 F0 E1 E2 75 [i_ZVREO)P@vP=@5u]
*Mar 8 00:03:06.928: RADIUS: 50 00 00 18 00 2F 00 35 00 05 00 0A C0 13 C0 14 C0 09 C0 0A 00 32 00 38 00 13 00 04 01 00 00 15 FF 01 00 01 00 00 0A 00 06 00 04 00 17 00 18 00 0B 00 02 01 00 [ P/528]
*Mar 8 00:03:06.928: RADIUS: Message-Authenticato[80] 18
*Mar 8 00:03:06.928: RADIUS: A3 28 CE 27 20 C0 D6 2C 11 01 D6 61 1F C3 6F 03 [ (' ,ao]
*Mar 8 00:03:06.928: RADIUS: EAP-Key-Name [102] 2 *
*Mar 8 00:03:06.928: RADIUS: Vendor, Cisco [26] 49
*Mar 8 00:03:06.928: RADIUS: Cisco AVpair [1] 43 "audit-session-id=0A1AED0B000000EE240F5BAB"
*Mar 8 00:03:06.928: RADIUS: NAS-Port-Type [61] 6 Ethernet [15]
*Mar 8 00:03:06.928: RADIUS: NAS-Port [5] 6 50001
*Mar 8 00:03:06.928: RADIUS: NAS-Port-Id [87] 17 "FastEthernet0/1"
*Mar 8 00:03:06.928: RADIUS: State [24] 30
*Mar 8 00:03:06.928: RADIUS: 00 7D 00 9B 00 C1 00 40 ED B8 45 00 FC DD 50 2E DC 0E E6 03 FC 7B AD 4C B7 E7 B1 70 [ }@EP.{Lp]
*Mar 8 00:03:06.928: RADIUS: NAS-IP-Address [4] 6 10.26.237.11
*Mar 8 00:03:06.928: RADIUS: Acct-Session-Id [44] 10 "000002D4"
*Mar 8 00:03:06.928: RADIUS(000001C7): Started 3 sec timeout
*Mar 8 00:03:07.004: RADIUS: Received from id 1645/84 10.26.13.59:1812, Access-Challenge, len 1188
*Mar 8 00:03:07.004: RADIUS: authenticator 7B 52 29 05 7E C3 EF 8E - 13 38 30 03 4B 65 64 0F
*Mar 8 00:03:07.004: RADIUS: EAP-Message [79] 255
*Mar 8 00:03:07.004: RADIUS: 01 03 04 56 0D C0 00 00 05 78 16 03 01 00 51 02 00 00 4D 03 01 52 C5 45 4F 0F 04 37 77 A0 C2 68 66 4E 45 92 AB 3D 7F 94 70 AF 36 [VxQMREO7whfNE=p6]
*Mar 8 00:03:07.004: RADIUS: 1D C5 17 23 5C F1 FA CA 60 B0 20 A5 48 16 D5 3F F9 B0 FF 38 1D D5 13 B3 88 13 06 EF DC 87 5C AE 17 E7 7E 80 84 21 58 64 F7 A6 36 00 35 00 00 05 FF 01 00 01 00 16 03 01 02 1C 0B 00 02 18 00 02 15 00 02 12 30 82 02 0E 30 [#\` H?8\~!Xd6500]
*Mar 8 00:03:07.004: RADIUS: 82 01 77 A0 03 02 01 02 02 09 00 88 7A CB 35 3F 1E 3E 62 30 0D 06 09 2A 86 48 86 F7 0D 01 01 05 05 00 30 2F 31 15 30 13 06 03 55 04 03 13 0C 53 50 [wz5?>b0*H0/10USP]
*Mar 8 00:03:07.004: RADIUS: 49 4E 41 56 44 30 30 30 30 34 31 16 30 14 06 03 55 04 0A 13 0D 50 6F 6C [INAVD0000410UPol]
*Mar 8 00:03:07.004: RADIUS: 69 63 79 4D 61 6E 61 67 65 72 30 1E 17 0D 31 33 30 38 32 [icyManager013082]
*Mar 8 00:03:07.004: RADIUS: 37 30 37 32 34 33 30 5A 17 0D 31 34 30 38 32 37 30 37 [7072430Z14082707]
*Mar 8 00:03:07.004: RADIUS: 32 34 33 30 5A 30 2F 31 15 30 13 06 03 55 04 03 13 0C 53 50 49 4E 41 56 [2430Z0/10USPINAV]
*Mar 8 00:03:07.004: RADIUS: 44 30 30 [ D00]
*Mar 8 00:03:07.004: RADIUS: EAP-Message [79] 255
*Mar 8 00:03:07.004: RADIUS: 30 30 34 31 16 30 14 06 03 55 04 0A 13 0D 50 6F 6C 69 63 79 4D 61 6E 61 [00410UPolicyMana]
*Mar 8 00:03:07.004: RADIUS: 67 65 72 30 81 9F 30 0D 06 09 2A 86 48 86 F7 0D 01 01 01 05 00 03 81 8D 00 30 81 89 02 81 81 00 C9 B9 03 65 83 EB 39 86 14 BC 95 7B DB 07 7E C5 8A D7 DA C7 8A CA 5A 88 6E 0B 93 06 35 57 [ger00*H0e9{~Zn5W]
*Mar 8 00:03:07.012: RADIUS: 6E DE 93 CD C9 FE 8E 9F E1 5F A9 04 5C BD A9 AD 5A 04 6E 35 47 76 A1 58 E5 C4 32 D7 49 9E 17 75 20 C6 6F 45 40 [n_\Zn5GvX2Iu oE@]
*Mar 8 00:03:07.012: RADIUS: AC EF 40 6D 15 38 F9 C2 28 7E C9 68 37 52 3B BF F4 C1 5E B8 BA 46 68 43 79 B1 65 66 [@m8(~h7R;^FhCyef]
*Mar 8 00:03:07.012: RADIUS: 9E 58 ED EC 8C 95 A2 D8 BF AA 77 AC 85 90 E3 AB C6 27 3A A2 22 AC 1C 48 B3 BF BE F7 85 CF 5C BB 2D 02 03 01 00 01 A3 32 30 30 30 0F 06 03 55 1D 11 04 08 30 06 87 04 0A 1A 0D 3B 30 [Xw':"H\-2000U0;0]
*Mar 8 00:03:07.012: RADIUS: 1D 06 03 55 1D 25 04 16 30 14 06 08 2B 06 01 05 05 07 03 01 06 08 2B 06 01 05 05 07 03 03 30 0D 06 09 2A 86 48 86 F7 0D 01 01 [ U?0++0*H]
*Mar 8 00:03:07.012: RADIUS: EAP-Message [79] 255
*Mar 8 00:03:07.012: RADIUS: 05 05 00 03 81 81 00 C4 46 3E 38 3D 53 0F 28 34 C1 A6 ED DC 70 76 9B 70 6B A8 95 7C 44 8E 7D 6E D6 8B 6D [F>8=S(4pvpk|D}nm]
*Mar 8 00:03:07.012: RADIUS: 90 49 83 06 E4 BF 68 2F 9D 77 78 A3 76 76 19 84 AD 26 3F F3 ED AA 88 52 35 0E 35 DD 00 E5 96 88 44 30 79 A0 71 [Ih/wxvv&?R55D0yq]
*Mar 8 00:03:07.012: RADIUS: 8D 25 3E 77 A0 E0 43 92 33 55 40 E1 C8 EE 88 11 25 E2 70 28 11 6C 5A 4E 3D F1 93 57 0A 6F [?>wC3U@?p(lZN=Wo]
*Mar 8 00:03:07.012: RADIUS: 36 51 72 04 08 C0 C0 DF F0 94 A9 F7 A1 05 C8 37 D6 F8 D4 9C 20 1A 7B CD 2C 17 83 7B 8E 20 F7 2D B6 16 03 01 02 FC 0D 00 02 F4 03 01 02 40 02 EE 00 63 30 61 31 0B 30 [6Qr7 {,{ -@c0a10]
*Mar 8 00:03:07.012: RADIUS: 09 06 03 55 04 06 13 02 55 53 31 15 30 13 06 03 55 04 0A 13 0C 44 69 67 69 43 65 72 74 20 49 [UUS10UDigiCert I]
*Mar 8 00:03:07.012: RADIUS: 6E 63 31 19 30 17 06 03 55 04 0B 13 10 77 77 77 2E 64 69 67 69 63 65 72 [nc10Uwww.digicer]
*Mar 8 00:03:07.012: RADIUS: 74 2E 63 6F 6D 31 20 30 1E 06 03 55 04 03 13 17 44 69 67 69 43 65 72 [t.com1 0UDigiCer]
*Mar 8 00:03:07.012: RADIUS: 74 20 47 6C 6F 62 61 6C 20 52 6F 6F 74 20 43 41 [t Global Root CA]
*Mar 8 00:03:07.012: RADIUS: 00 48 [ H]
*Mar 8 00:03:07.012: RADIUS: EAP-Message [79] 255
*Mar 8 00:03:07.012: RADIUS: 30 46 31 18 30 16 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 08 69 6E 74 72 61 6E 65 74 31 [0F10&,dintranet1]
*Mar 8 00:03:07.020: RADIUS: 12 30 10 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 02 49 4E 31 16 30 14 06 03 55 04 03 13 0D 49 6E 64 69 61 20 52 [0&,dIN10UIndia R]
*Mar 8 00:03:07.020: RADIUS: 6F 6F 74 20 43 41 00 4A 30 48 31 18 30 16 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 08 69 6E [oot CAJ0H10&,din]
*Mar 8 00:03:07.020: RADIUS: 74 72 61 6E 65 74 31 12 30 10 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 02 49 4E 31 18 30 16 06 03 55 [tranet10&,dIN10U]
*Mar 8 00:03:07.020: RADIUS: 04 03 13 0F 45 6E 74 65 72 70 72 69 73 65 20 43 41 2D 31 00 4D [Enterprise CA-1M]
*Mar 8 00:03:07.020: RADIUS: 30 4B 31 18 30 16 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 08 69 6E 74 72 61 6E 65 74 31 [0K10&,dintranet1]
*Mar 8 00:03:07.020: RADIUS: 12 30 10 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 02 49 4E 31 1B 30 19 06 03 55 04 03 13 12 49 4E 2D 53 50 49 4E [0&,dIN10UIN-SPIN]
*Mar 8 00:03:07.020: RADIUS: 43 52 54 30 30 30 30 33 2D 43 41 00 D5 30 81 D2 31 0B 30 09 06 03 55 04 06 13 02 55 [CRT00003-CA010UU]
*Mar 8 00:03:07.020: RADIUS: 53 31 13 30 11 06 03 55 04 [ S10U]
*Mar 8 00:03:07.020: RADIUS: EAP-Message [79] 100
*Mar 8 00:03:07.020: RADIUS: 08 0C 0A 43 61 6C 69 66 6F 72 6E 69 61 31 12 30 10 06 03 55 04 07 0C 09 53 75 6E [California10USun]
*Mar 8 00:03:07.020: RADIUS: 6E 79 76 61 6C 65 31 17 30 15 06 03 55 04 0A 0C 0E 41 72 75 62 61 20 4E [nyvale10UAruba N]
*Mar 8 00:03:07.020: RADIUS: 65 74 77 6F 72 6B 73 31 40 30 3E 06 03 55 04 03 0C 37 43 6C 65 [etworks1@0>U7Cle]
*Mar 8 00:03:07.020: RADIUS: 61 72 50 61 73 73 20 4F 6E 62 6F 61 72 64 20 4C [arPass Onboard L]
*Mar 8 00:03:07.020: RADIUS: 6F 63 61 6C 20 43 65 72 74 69 [ ocal Certi]
*Mar 8 00:03:07.020: RADIUS: Message-Authenticato[80] 18
*Mar 8 00:03:07.020: RADIUS: 12 75 40 41 6F 40 6B 6F A5 FE AB 85 F3 B3 CF A4 [ u@Ao@ko]
*Mar 8 00:03:07.020: RADIUS: State [24] 30
*Mar 8 00:03:07.020: RADIUS: 00 6F 00 51 00 4B 00 6E EE B8 45 00 4B AA 6B A9 B6 D6 C8 CC 48 1A 91 99 7F 77 D3 C1 [ oQKnEKkHw]
*Mar 8 00:03:07.029: RADIUS(000001C7): Received from id 1645/84
*Mar 8 00:03:07.029: RADIUS/DECODE: EAP-Message fragments, 253+253+253+253+98, total 1110 bytes
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): Posting EAP_REQ for 0xB0000DBA
*Mar 8 00:03:07.037: dot1x_auth_bend Fa0/1: during state auth_bend_response, got event 7(eapReq)
*Mar 8 00:03:07.037: @@@ dot1x_auth_bend Fa0/1: auth_bend_response -> auth_bend_request
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_exit called
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
*Mar 8 00:03:07.037: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:07.037: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:07.037: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:07.037: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:07.037: EAPOL pak dump Tx
*Mar 8 00:03:07.037: EAPOL Version: 0x3 type: 0x0 length: 0x0456
*Mar 8 00:03:07.037: EAP code: 0x1 id: 0x3 length: 0x0456 type: 0xD
*Mar 8 00:03:07.037: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_request_action called
*Mar 8 00:03:07.037: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:07.037: dot1x-packet(Fa0/1): Queuing an EAPOL pkt on Authenticator Q
*Mar 8 00:03:07.037: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
*Mar 8 00:03:07.037: EAPOL pak dump rx
*Mar 8 00:03:07.037: EAPOL Version: 0x1 type: 0x0 length: 0x0006
*Mar 8 00:03:07.037: dot1x-ev:
dot1x_auth_queue_event: Int Fa0/1 CODE= 2,TYPE= 13,LEN= 6
*Mar 8 00:03:07.037: dot1x-packet(Fa0/1): Received an EAPOL frame
*Mar 8 00:03:07.037: dot1x-ev(Fa0/1): Received pkt saddr =d43d.7e65.4fc1 , daddr = 0180.c200.0003,
pae-ether-type = 888e.0100.0006
*Mar 8 00:03:07.037: dot1x-packet(Fa0/1): Received an EAP packet
*Mar 8 00:03:07.037: EAPOL pak dump rx
*Mar 8 00:03:07.037: EAPOL Version: 0x1 type: 0x0 length: 0x0006
*Mar 8 00:03:07.037: dot1x-packet(Fa0/1): Received an EAP packet from d43d.7e65.4fc1
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): Posting EAPOL_EAP for 0xB0000DBA
*Mar 8 00:03:07.037: dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 6(eapolEap)
*Mar 8 00:03:07.037: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_response
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_enter called
*Mar 8 00:03:07.037: dot1x-ev(Fa0/1): dot1x_sendRespToServer: Response sent to the server from 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_response_action called
*Mar 8 00:03:07.037: AAA/AUTHEN/8021X (000001C7): Pick method list 'default'
*Mar 8 00:03:07.046: RADIUS/ENCODE(000001C7):Orig. component type = DOT1X
*Mar 8 00:03:07.046: RADIUS(000001C7): Config NAS IP: 0.0.0.0
*Mar 8 00:03:07.046: RADIUS/ENCODE(000001C7): acct_session_id: 724
*Mar 8 00:03:07.046: RADIUS(000001C7): sending
*Mar 8 00:03:07.046: RADIUS/ENCODE: Best Local IP-Address 10.26.237.11 for Radius-Server 10.26.13.59
*Mar 8 00:03:07.046: RADIUS(000001C7): Send Access-Request to 10.26.13.59:1812 id 1645/85, len 253
*Mar 8 00:03:07.046: RADIUS: authenticator 1C D7 6D 40 A3 D6 BA B1 - A7 E6 70 DA 32 83 2E 19
*Mar 8 00:03:07.046: RADIUS: User-Name [1] 31 "host/D0902MALL005.IN.intranet"
*Mar 8 00:03:07.046: RADIUS: Service-Type [6] 6 Framed [2]
*Mar 8 00:03:07.046: RADIUS: Framed-MTU [12] 6 1500
*Mar 8 00:03:07.046: RADIUS: Called-Station-Id [30] 19 "D4-A0-2A-EE-14-81"
*Mar 8 00:03:07.046: RADIUS: Calling-Station-Id [31] 19 "D4-3D-7E-65-4F-C1"
*Mar 8 00:03:07.046: RADIUS: EAP-Message [79] 8
*Mar 8 00:03:07.046: RADIUS: 02 03 00 06 0D 00
*Mar 8 00:03:07.046: RADIUS: Message-Authenticato[80] 18
*Mar 8 00:03:07.046: RADIUS: 73 1D 89 5C 66 19 32 B6 63 C2 64 C1 04 42 A9 F9 [ s\f2cdB]
*Mar 8 00:03:07.046: RADIUS: EAP-Key-Name [102] 2 *
*Mar 8 00:03:07.046: RADIUS: Vendor, Cisco [26] 49
*Mar 8 00:03:07.046: RADIUS: Cisco AVpair [1] 43 "audit-session-id=0A1AED0B000000EE240F5BAB"
*Mar 8 00:03:07.046: RADIUS: NAS-Port-Type [61] 6 Ethernet [15]
*Mar 8 00:03:07.046: RADIUS: NAS-Port [5] 6 50001
*Mar 8 00:03:07.046: RADIUS: NAS-Port-Id [87] 17 "FastEthernet0/1"
*Mar 8 00:03:07.046: RADIUS: State [24] 30
*Mar 8 00:03:07.046: RADIUS: 00 6F 00 51 00 4B 00 6E EE B8 45 00 4B AA 6B A9 B6 D6 C8 CC 48 1A 91 99 7F 77 D3 C1 [ oQKnEKkHw]
*Mar 8 00:03:07.046: RADIUS: NAS-IP-Address [4] 6 10.26.237.11
*Mar 8 00:03:07.046: RADIUS: Acct-Session-Id [44] 10 "000002D4"
*Mar 8 00:03:07.046: RADIUS(000001C7): Started 3 sec timeout
*Mar 8 00:03:07.113: RADIUS: Received from id 1645/85 10.26.13.59:1812, Access-Challenge, len 378
*Mar 8 00:03:07.113: RADIUS: authenticator 1A 85 26 09 58 84 BC D4 - E0 A9 E3 C0 25 31 2D 31
*Mar 8 00:03:07.113: RADIUS: EAP-Message [79] 255
*Mar 8 00:03:07.121: RADIUS: 01 04 01 32 0D 00 66 69 63 61 74 65 20 41 75 74 68 6F 72 69 74 [2ficate Authorit]
*Mar 8 00:03:07.121: RADIUS: 79 20 28 53 69 67 6E 69 6E 67 29 31 3F 30 3D 06 09 2A [y (Signing)1?0=*]
*Mar 8 00:03:07.121: RADIUS: 86 48 86 F7 0D 01 09 01 16 30 64 36 62 62 34 66 37 30 2D 66 34 31 32 2D [H0d6bb4f70-f412-]
*Mar 8 00:03:07.121: RADIUS: 34 35 35 32 2D 61 65 65 32 2D 63 37 61 30 32 36 [4552-aee2-c7a026]
*Mar 8 00:03:07.121: RADIUS: 66 62 61 32 31 38 40 65 78 61 6D 70 6C 65 2E 63 [[email protected]]
*Mar 8 00:03:07.121: RADIUS: 6F 6D 00 CB 30 81 C8 31 0B 30 09 06 03 55 04 06 13 02 55 53 31 13 30 11 06 03 55 04 08 0C 0A 43 61 6C 69 66 [om010UUS10UCalif]
*Mar 8 00:03:07.121: RADIUS: 6F 72 6E 69 61 31 12 30 10 06 03 55 04 07 0C 09 53 75 6E 6E 79 76 61 6C [ornia10USunnyval]
*Mar 8 00:03:07.121: RADIUS: 65 31 17 30 15 06 03 55 04 0A 0C 0E 41 72 75 62 61 20 4E 65 74 77 6F 72 [e10UAruba Networ]
*Mar 8 00:03:07.121: RADIUS: 6B 73 31 36 30 34 06 03 55 04 03 0C 2D 43 6C 65 61 72 50 61 73 [ks1604U-ClearPas]
*Mar 8 00:03:07.121: RADIUS: 73 20 4F 6E 62 6F 61 72 64 20 4C 6F 63 61 6C 20 [s Onboard Local ]
*Mar 8 00:03:07.121: RADIUS: 43 65 72 74 69 66 69 63 61 74 65 20 41 75 74 68 [Certificate Auth]
*Mar 8 00:03:07.121: RADIUS: 6F 72 69 74 79 31 3F 30 3D 06 09 2A 86 48 86 F7 0D 01 09 01 16 [ ority1?0=*H]
*Mar 8 00:03:07.121: RADIUS: EAP-Message [79] 55
*Mar 8 00:03:07.121: RADIUS: 30 64 36 62 62 34 66 37 30 2D 66 34 31 32 2D 34 [0d6bb4f70-f412-4]
*Mar 8 00:03:07.121: RADIUS: 35 35 32 2D 61 65 65 32 2D 63 37 61 30 32 36 66 [552-aee2-c7a026f]
*Mar 8 00:03:07.121: RADIUS: 62 61 32 31 38 40 65 78 61 6D 70 6C 65 2E 63 6F [[email protected]]
*Mar 8 00:03:07.121: RADIUS: 6D 0E 00 00 00 [ m]
*Mar 8 00:03:07.121: RADIUS: Message-Authenticato[80] 18
*Mar 8 00:03:07.121: RADIUS: 4C 46 AA B9 A5 D5 DF EA DB E7 2B 7B 51 7E 58 3F [ LF+{Q~X?]
*Mar 8 00:03:07.121: RADIUS: State [24] 30
*Mar 8 00:03:07.121: RADIUS: 00 EF 00 B9 00 0A 00 00 EF B8 45 00 EF D2 C4 3C 81 6C 72 0E 23 FE 11 EA 12 17 50 A1 [ E
*Mar 8 00:03:07.121: RADIUS(000001C7): Received from id 1645/85
*Mar 8 00:03:07.121: RADIUS/DECODE: EAP-Message fragments, 253+53, total 306 bytes
*Mar 8 00:03:07.130: dot1x-sm(Fa0/1): Posting EAP_REQ for 0xB0000DBA
*Mar 8 00:03:07.130: dot1x_auth_bend Fa0/1: during state auth_bend_response, got event 7(eapReq)
*Mar 8 00:03:07.130: @@@ dot1x_auth_bend Fa0/1: auth_bend_response -> auth_bend_request
*Mar 8 00:03:07.130: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_exit called
*Mar 8 00:03:07.130: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
*Mar 8 00:03:07.130: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:07.130: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:07.130: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:07.130: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:07.130: EAPOL pak dump Tx
*Mar 8 00:03:07.130: EAPOL Version: 0x3 type: 0x0 length: 0x0132
*Mar 8 00:03:07.130: EAP code: 0x1 id: 0x4 length: 0x0132 type: 0xD
*Mar 8 00:03:07.130: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:07.130: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_request_action called
*Mar 8 00:03:07.138: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:07.138: dot1x-packet(Fa0/1): Queuing an EAPOL pkt on Authenticator Q
*Mar 8 00:03:07.138: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
*Mar 8 00:03:07.138: EAPOL pak dump rx
*Mar 8 00:03:07.138: EAPOL Version: 0x1 type: 0x0 length: 0x05D4
*Mar 8 00:03:07.138: dot1x-ev:
dot1x_auth_queue_event: Int Fa0/1 CODE= 2,TYPE= 13,LEN= 1492
*Mar 8 00:03:07.138: dot1x-packet(Fa0/1): Received an EAPOL frame
*Mar 8 00:03:07.138: dot1x-ev(Fa0/1):
^Z
Malleswaram_2960#
*Mar 8 00:03:07.180: RADIUS: State [24] 30
*Mar 8 00:03:07.180: RADIUS: 00 EF 00 B9 00 0A 00 00 EF B8 45 00 EF D2 C4 3C 81 6C 72 0E 23 FE 11 EA 12 17 50 A1 [ E
*Mar 8 00:03:07.180: RADIUS: NAS-IP-Address [4] 6 10.26.237.11
*Mar 8 00:03:07.180: RADIUS: Acct-Session-Id [44] 10 "000002D4"
*Mar 8 00:03:07.180: RADIUS(000001C7): Started 3 sec timeout
Malleswaram_2960#
*Mar 8 00:03:07.893: %SYS-5-CONFIG_I: Configured from console by jameela on vty0 (10.26.20.5)
Malleswaram_2960#
*Mar 8 00:03:10.225: RADIUS(000001C7): Request timed out
*Mar 8 00:03:10.225: RADIUS: Retransmit to (10.26.13.59:1812,1813) for id 1645/86
*Mar 8 00:03:10.225: RADIUS(000001C7): Started 3 sec timeout
Malleswaram_2960#
*Mar 8 00:03:13.354: RADIUS(000001C7): Request timed out
*Mar 8 00:03:13.354: RADIUS: Retransmit to (10.26.13.59:1812,1813) for id 1645/86
*Mar 8 00:03:13.354: RADIUS(000001C7): Started 3 sec timeout
Malleswaram_2960#
*Mar 8 00:03:16.307: RADIUS(000001C7): Request timed out
*Mar 8 00:03:16.307: RADIUS: Retransmit to (10.26.13.59:1812,1813) for id 1645/86
*Mar 8 00:03:16.307: RADIUS(000001C7): Started 3 sec timeout
Malleswaram_2960#
*Mar 8 00:03:19.369: RADIUS(000001C7): Request timed out
*Mar 8 00:03:19.369: RADIUS: Retransmit to (10.26.13.59:1812,1813) for id 1645/86
*Mar 8 00:03:19.369: RADIUS(000001C7): Started 3 sec timeout
Malleswaram_2960#
*Mar 8 00:03:22.456: RADIUS(000001C7): Request timed out
*Mar 8 00:03:22.456: RADIUS: Fail-over denied to (10.26.13.59:1812,1813) for id 1645/86
*Mar 8 00:03:22.456: RADIUS: No response from (10.26.13.59:1812,1813) for id 1645/86
*Mar 8 00:03:22.456: RADIUS/DECODE: parse response no app start; FAIL
*Mar 8 00:03:22.456: RADIUS/DECODE: parse response; FAIL
*Mar 8 00:03:22.456: dot1x-ev(Fa0/1): Received an EAP Fail
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): Posting EAP_FAIL for 0xB0000DBA
*Mar 8 00:03:22.456: dot1x_auth_bend Fa0/1: during state auth_bend_response, got event 10(eapFail)
*Mar 8 00:03:22.456: @@@ dot1x_auth_bend Fa0/1: auth_bend_response -> auth_bend_fail
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_exit called
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_fail_enter called
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_fail_action called
*Mar 8 00:03:22.456: dot1x_auth_bend Fa0/1: idle during state auth_bend_fail
*Mar 8 00:03:22.456: @@@ dot1x_auth_bend Fa0/1: auth_bend_fail -> auth_bend_idle
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_enter called
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): Posting AUTH_FAIL on Client 0xB0000DBA
*Mar 8 00:03:22.456: dot1x_auth Fa0/1: during state auth_authenticating, got event 15(authFail)
*Mar 8 00:03:22.456: @@@ dot1x_auth Fa0/1: auth_authenticating -> auth_authc_result
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authenticating_exit called
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authc_result_enter called
*Mar 8 00:03:22.456: %DOT1X-5-FAIL: Authentication failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID
*Mar 8 00:03:22.456: dot1x-ev(Fa0/1): Sending event (2) to Auth Mgr for d43d.7e65.4fc1
*Mar 8 00:03:22.456: %AUTHMGR-7-RESULT: Authentication result 'fail' from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EE240F5BAB
*Mar 8 00:03:22.456: %AUTHMGR-5-FAIL: Authorization failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EE240F5BAB
*Mar 8 00:03:22.456: dot1x-redundancy: State for client d43d.7e65.4fc1 successfully retrieved
*Mar 8 00:03:22.456: dot1x-ev(Fa0/1): Received Authz fail for the client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): Posting_AUTHZ_FAIL on Client 0xB0000DBA
*Mar 8 00:03:22.456: dot1x_auth Fa0/1: during state auth_authc_result, got event 22(authzFail)
*Mar 8 00:03:22.456: @@@ dot1x_auth Fa0/1: auth_authc_result -> auth_held
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_held_enter called
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:22.464: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:22.464: EAPOL pak dump Tx
*Mar 8 00:03:22.464: EAPOL Version: 0x3 type: 0x0 length: 0x0004
*Mar 8 00:03:22.464: EAP code: 0x4 id: 0x4 length: 0x0004
*Mar 8 00:03:22.464: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): Posting FAILOVER_RETRY on Client 0xB0000DBA
*Mar 8 00:03:22.464: dot1x_auth Fa0/1: during state auth_held, got event 21(failover_retry)
*Mar 8 00:03:22.464: @@@ dot1x_auth Fa0/1: auth_held -> auth_restart
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_held_exit called
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_enter called
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Sending create new context event to EAP for 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_held_restart_action called
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): Posting !EAP_RESTART on Client 0xB0000DBA
*Mar 8 00:03:22.464: dot1x_auth Fa0/1: during state auth_restart, got event 6(no_eapRestart)
*Mar 8 00:03:22.464: @@@ dot1x_auth Fa0/1: auth_restart -> auth_connecting
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_enter called
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_connecting_action called
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): Posting REAUTH_MAX on Client 0xB0000DBA
*Mar 8 00:03:22.464: dot1x_auth Fa0/1: during state auth_connecting, got event 11(reAuthMax)
*Mar 8 00:03:22.464: @@@ dot1x_auth Fa0/1: auth_connecting -> auth_disconnected
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_disconnected_enter called
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): d43d.7e65.4fc1:auth_disconnected_enter sending canned failure to version 1 supplicant
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:22.464: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:22.464: EAPOL pak dump Tx
*Mar 8 00:03:22.464: EAPOL Version: 0x3 type: 0x0 length: 0x0004
*Mar 8 00:03:22.464: EAP code: 0x4 id: 0x5 length: 0x0004
*Mar 8 00:03:22.464: dot1x-packet(Fa0/1): dot1x_auth_txCannedStatus: EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_disconnected_reAuthMax_action called
*Mar 8 00:03:22.464: dot1x_auth Fa0/1: idle during state auth_disconnected
*Mar 8 00:03:22.464: @@@ dot1x_auth Fa0/1: auth_disconnected -> auth_restart
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Sending event (1) to Auth Mgr for d43d.7e65.4fc1
*Mar 8 00:03:22.464: dot1x-ev:Delete auth client (0xB0000DBA) message
*Mar 8 00:03:22.464: dot1x-ev:Auth client ctx destroyed
*Mar 8 00:03:22.674: AAA/BIND(000001C8): Bind i/f
*Mar 8 00:03:22.674: dot1x_auth Fa0/1: initial state auth_initialize has enter
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_initialize_enter called
*Mar 8 00:03:22.674: dot1x_auth Fa0/1: during state auth_initialize, got event 0(cfg_auto)
*Mar 8 00:03:22.674: @@@ dot1x_auth Fa0/1: auth_initialize -> auth_disconnected
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_disconnected_enter called
*Mar 8 00:03:22.674: dot1x_auth Fa0/1: idle during state auth_disconnected
*Mar 8 00:03:22.674: @@@ dot1x_auth Fa0/1: auth_disconnected -> auth_restart
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_restart_enter called
*Mar 8 00:03:22.674: dot1x-ev(Fa0/1): Sending create new context event to EAP for 0x4A000DBB (0000.0000.0000)
*Mar 8 00:03:22.674: dot1x_auth_bend Fa0/1: initial state auth_bend_initialize has enter
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_initialize_enter called
*Mar 8 00:03:22.674: dot1x_auth_bend Fa0/1: initial state auth_bend_initialize has idle
*Mar 8 00:03:22.674: dot1x_auth_bend Fa0/1: during state auth_bend_initialize, got event 16383(idle)
*Mar 8 00:03:22.674: @@@ dot1x_auth_bend Fa0/1: auth_bend_initialize -> auth_bend_idle
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_idle_enter called
*Mar 8 00:03:22.674: dot1x-ev(Fa0/1): Created a client entry (0x4A000DBB)
*Mar 8 00:03:22.674: dot1x-ev(Fa0/1): Dot1x authentication started for 0x4A000DBB (0000.0000.0000)
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): Posting !EAP_RESTART on Client 0x4A000DBB
*Mar 8 00:03:22.674: dot1x_auth Fa0/1: during state auth_restart, got event 6(no_eapRestart)
*Mar 8 00:03:22.674: @@@ dot1x_auth Fa0/1: auth_restart -> auth_connecting
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_connecting_enter called
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_restart_connecting_action called
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): Posting RX_REQ on Client 0x4A000DBB
*Mar 8 00:03:22.674: dot1x_auth Fa0/1: during state auth_connecting, got event 10(eapReq_no_reAuthMax)
*Mar 8 00:03:22.674: @@@ dot1x_auth Fa0/1: auth_connecting -> auth_authenticating
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_authenticating_enter called
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_connecting_authenticating_action called
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): Posting AUTH_START for 0x4A000DBB
*Mar 8 00:03:22.674: dot1x_auth_bend Fa0/1: during state auth_bend_idle, got event 4(eapReq_authStart)
*Mar 8 00:03:22.674: @@@ dot1x_auth_bend Fa0/1: auth_bend_idle -> auth_bend_request
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_enter called
*Mar 8 00:03:22.674: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:22.674: dot1x-ev(Fa0/1): Role determination not required
Malleswaram_2960#
*Mar 8 00:03:22.674: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:22.674: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:22.674: EAPOL pak dump Tx
*Mar 8 00:03:22.674: EAPOL Version: 0x3 type: 0x0 length: 0x0005
*Mar 8 00:03:22.674: EAP code: 0x1 id: 0x1 length: 0x0005 type: 0x1
*Mar 8 00:03:22.674: dot1x-packet(Fa0/1): EAPOL packet sent to client 0x4A000DBB (0000.0000.0000)
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_idle_request_action called
*Mar 8 00:03:22.791: dot1x-ev(Fa0/1): New client notification from AuthMgr for 0x4A000DBB - d43d.7e65.4fc1
*Mar 8 00:03:22.791: %AUTHMGR-5-START: Starting 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:03:25.761: dot1x-sm(Fa0/1): Posting EAP_REQ for 0x4A000DBB
*Mar 8 00:03:25.761: dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 7(eapReq)
*Mar 8 00:03:25.761: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_request
*Mar 8 00:03:25.761: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_request_action called
*Mar 8 00:03:25.761: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_enter called
*Mar 8 00:03:25.761: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:25.761: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:25.761: dot1x-registry:registry:dot1x_ether_macaddr called
Malleswaram_2960#n
*Mar 8 00:03:25.761: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:25.761: EAPOL pak dump Tx
*Mar 8 00:03:25.761: EAPOL Version: 0x3 type: 0x0 length: 0x0005
*Mar 8 00:03:25.761: EAP code: 0x1 id: 0x1 length: 0x0005 type: 0x1
*Mar 8 00:03:25.761: dot1x-packet(Fa0/1): EAPOL packet sent to client 0x4A000DBB (d43d.7e65.4fc1)
Malleswaram_2960#no debu
Malleswaram_2960#no debug
*Mar 8 00:03:28.848: dot1x-sm(Fa0/1): Posting EAP_REQ for 0x4A000DBB
*Mar 8 00:03:28.848: dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 7(eapReq)
*Mar 8 00:03:28.848: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_request
*Mar 8 00:03:28.848: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_request_action called
*Mar 8 00:03:28.848: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_enter called
*Mar 8 00:03:28.848: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:28.848: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:28.848: dot1x-registry:registry:dot1x_ether_macaddr called
Malleswaram_2960#no debug all
*Mar 8 00:03:28.848: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:28.848: EAPOL pak dump Tx
*Mar 8 00:03:28.848: EAPOL Version: 0x3 type: 0x0 length: 0x0005
*Mar 8 00:03:28.848: EAP code: 0x1 id: 0x1 length: 0x0005 type: 0x1
*Mar 8 00:03:28.848: dot1x-packet(Fa0/1): EAPOL packet sent to client 0x4A000DBB (d43d.7e65.4fc1)
Malleswaram_2960#no debug all
All possible debugging has been turned off
Malleswaram_2960#
*Mar 8 00:03:31.180: AAA: parse name=tty1 idb type=-1 tty=-1
*Mar 8 00:03:31.180: AAA: name=tty1 flags=0x11 type=5 shelf=0 slot=0 adapter=0 port=1 channel=0
*Mar 8 00:03:31.180: AAA/MEMORY: create_user (0x21D1684) user='jameela' ruser='Malleswaram_2960' ds0=0 port='tty1' rem_addr='10.26.20.5' authen_type=ASCII service=NONE priv=15 initial_task_id='0', vrf= (id=0) key=C9A1F1D1
*Mar 8 00:03:31.389: TAC+: (-1901802859): received author response status = PASS_ADD
*Mar 8 00:03:31.389: AAA/MEMORY: free_user (0x21D1684) user='jameela' ruser='Malleswaram_2960' port='tty1' rem_addr='10.26.20.5' authen_type=ASCII service=NONE priv=15
*Mar 8 00:03:31.935: %DOT1X-5-FAIL: Authentication failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID
*Mar 8 00:03:31.935: %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
*Mar 8 00:03:31.935: %AUTHMGR-7-FAILOVER: Failing over from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
*Mar 8 00:03:31.935: %AUTHMGR-7-NOMOREMETHODS: Exhausted all authentication methods for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:03:31.935: %AUTHMGR-5-FAIL: Authorization failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#no deb
Malleswaram_2960#no debug al
Malleswaram_2960#no debug all
All possible debugging has been turned off
Malleswaram_2960#
*Mar 8 00:04:32.677: %AUTHMGR-5-START: Starting 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:04:41.938: %DOT1X-5-FAIL: Authentication failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID
*Mar 8 00:04:41.938: %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
*Mar 8 00:04:41.938: %AUTHMGR-7-FAILOVER: Failing over from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
*Mar 8 00:04:41.938: %AUTHMGR-7-NOMOREMETHODS: Exhausted all authentication methods for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:04:41.938: %AUTHMGR-5-FAIL: Authorization failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:05:42.654: %AUTHMGR-5-START: Starting 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:05:51.915: %DOT1X-5-FAIL: Authentication failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID
*Mar 8 00:05:51.915: %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
*Mar 8 00:05:51.915: %AUTHMGR-7-FAILOVER: Failing over from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
*Mar 8 00:05:51.915: %AUTHMGR-7-NOMOREMETHODS: Exhausted all authentication methods for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:05:51.915: %AUTHMGR-5-FAIL: Authorization failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Pls dont worry about day and time. -
Cisco sf-300 connected/trunked to 2960
I have a sf300 trunked and connected to a 2960 and can't get an ip. would the switch pickup the vlans already out there from my 3560 or do you have to configure the vlans in the sf300. I went ahead and configured each vlan in the sf300 and left port 1 as a trunk and gave the switch an ip that is on our mgmt vlan. I do not get an ip when connecting to the sf300. Also I can make the port on the 2960 a access port with STP, but do i need to set STP on the access port on the sf300? prefer using trunk.
Hi,
Really depends on the port connecting both switches together and how each port is configured. If 2960 port is configured as truck with native vlan 1, allowed vlans all then you will need to add each vlan to the port in the SF300 switch.
SF300 commands
conf t
interface FastEthernet 24
switchport trunk native vlan 1
switchport trunk allowed vlan add all
You will have to be on latest firmware for Cli support.
Again this is assuming the port on 2960 is configured to allow all vlans on that port.
Hope this helps,
Jasbryan -
I have an device that use Multicast and is unable to aquire an ip address when connected to a 2960 switch. I have a 3560 switch that is configured with the DHCP scope. We have DHCP pool configured. layer 2, and layer 3 switch's.
Basically what’s happing is that if we connect the device to the switch it does not get a DHCP address however if we apply a static address it works. Now I have duplicated this in the lab and the everything works fine, the only difference is that I have a different IOS on my Lab switch. The only thing i can think of is the IOS.
Any help would be appreciated.
The IOS on the 2960 is flash:c2960-lanbasek9-mz.122-55.SE7.Hi Anil,
I need to know the mac-address of the client as i see two different DHCP Requests from:
0100.237d.14b5
and
0198.fe94.dcd6
Moreover i see only one DHCP pool on the layer 3 switch:
ip dhcp pool
network 10.65.117.0 255.255.255.0
dns-server 198.6.1.122 198.6.1.142 8.8.8.8
default-router 10.65.117.1
And as you said that it should pick IP address from vlan2, but i dont see any pool for vlan2 on the contrary you did mention that if you connect your laptop on that port it does pick IP address from vlan 2. its actually very weird.
If possible collect the wireshark captures from machine interface for more debugging. i want to see the DHCP process. and let me know if you need any help in collecting captures
Regards,
RS -
We have a pair of Nexus 5596 switches, that each have a 1 gigabit conection to ISP CE switches (ME3400).
Switch 1 has a fibre connection using GLC-SX-MM with the following information...
sh int e1/48 trans
Ethernet1/48
transceiver is present
type is SFP-1000BASE-SX
name is CISCO-AVAGO
part number is SFBR-5766PZ-CS2
revision is
serial number is AGA1549L2BE
nominal bitrate is 1300 MBit/sec
cisco id is --
cisco extended id number is 4
I cannot get the port to come up on switch 2, transceiver info...
sh int e1/48 trans
Ethernet1/48
transceiver is present
type is SFP-1000BASE-SX
name is CISCO-AVAGO
part number is SFBR-5766PZ-CS2
revision is
serial number is AGA1549L2BE
nominal bitrate is 1300 MBit/sec
cisco id is --
cisco extended id number is 4
The port is up on the ISP switch, but down on the N5K...
Ethernet1/48 is down (Link not connected)
Hardware: 1000/10000 Ethernet, address: 547f.ee41.e337 (bia 547f.ee41.e337)
Description: Intech WAN ME3400-1 (BT)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec
reliability 255/255, txload 255/255, rxload 255/255
Encapsulation ARPA
Port mode is trunk
full-duplex, 1000 Mb/s, media type is 10G
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
EtherType is 0x8100
Last link flapped 00:31:00
Last clearing of "show interface" counters 00:00:47
30 seconds input rate 0 bits/sec, 0 packets/sec
30 seconds output rate 0 bits/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
input rate 242.30 Gbps, 163.37 Mpps; output rate 63.30 Gbps, 231.54 Mpps
RX
17828772964 unicast packets 2506759 multicast packets 991 broadcast packets
17831280714 input packets 3305852407174 bytes
897530002 jumbo packets 0 storm suppression bytes
20 runts 0 giants 0 CRC 0 no buffer
20 input error 0 short frame 0 overrun 0 underrun 0 ignored
0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
0 input with dribble 0 input discard Ethernet1/48 is down (Link not connected)
Hardware: 1000/10000 Ethernet, address: 547f.ee41.e337 (bia 547f.ee41.e337)
Description: Intech WAN ME3400-1 (BT)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec
reliability 255/255, txload 255/255, rxload 255/255
Encapsulation ARPA
Port mode is trunk
full-duplex, 1000 Mb/s, media type is 10G
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
EtherType is 0x8100
Last link flapped 00:31:00
Last clearing of "show interface" counters 00:00:47
30 seconds input rate 0 bits/sec, 0 packets/sec
30 seconds output rate 0 bits/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
input rate 242.30 Gbps, 163.37 Mpps; output rate 63.30 Gbps, 231.54 Mpps
RX
17828772964 unicast packets 2506759 multicast packets 991 broadcast packets
17831280714 input packets 3305852407174 bytes
897530002 jumbo packets 0 storm suppression bytes
20 runts 0 giants 0 CRC 0 no buffer
20 input error 0 short frame 0 overrun 0 underrun 0 ignored
0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
0 input with dribble 0 input discard
I have tested the SFP's in use on a pair of 2960's & they work fine!
If i replace the SFP's for copper, then they work fine also.
Does anyone know of any incompatibility issue with this SFP?
Thanks
ColinDid you try a different port such as e1/1? Sounds like a bug to me
http://www.cisco.com/en/US/prod/collateral/switches/ps9441/ps9670/data_sheet_c78-618603.html
Table 2.
Cisco Nexus 5500 Platform Transceiver Support Matrix -
Cisco 2960S SFF8472-5-THRESHOLD_VIOLATION
Hi All
I have a issue connecting my Cisco 3750X 12 port fibre switch to my Cisco 2960S 24Port switch using Multi Mode Fibre.
I have Mode condtioning cables connecting to the SFP (GLC-LH-SMD) on the 3750 via a fibre patch panel which bring me to the 2960s with its Mode conditioning cable and SFP (GLC-LH-SMD).
The fibre port on the Cisco 2960S was up for all of 10 mins and has gone out with the following error message.
%SFF8472-5-THRESHOLD_VIOLATION: Gi1/0/26: Rx power high warning; Operating value: -2.7 dBm, Threshold value: -3.0 dBm.
I did a show int transceiver command and got the following output.
DS-THN-SW3#show interfaces transceiver
If device is externally calibrated, only calibrated values are printed.
++ : high alarm, + : high warning, - : low warning, -- : low alarm.
NA or N/A: not applicable, Tx: transmit, Rx: receive.
mA: milliamperes, dBm: decibels (milliwatts).
Optical Optical
Temperature Voltage Tx Power Rx Power
Port (Celsius) (Volts) (dBm) (dBm)
Gi1/0/26 25.2 3.31 -5.1 -28.5
All SFP's are new as is the Multi Mode Fibre cable running from one building to another.Hi All,
One of member port of port channel was flapping and Here is the error message
Error log:
.Mar 17 08:27:37: %SFF8472-5-THRESHOLD_VIOLATION: Te6/1/1: Tx power low alarm; Operating value: -40.0 dBm, Threshold value: -11.3 dBm.
Cisco TAC analyse the issue under 629566213 but their initial advices was not much experience oriented.
Finally I have resolved the issue just by entering following command.
switch 6 frulink reload
Janaka Wellege Bsc.Eng
University of Peradeniya. -
Nexus 2K to Cisco 2960 IOS Switch
Hi,
I am trying to connect Nexus 2K FEX to Cisco 2960 IOS Switch (Trunk config) and causing spanning tree loop having issues. I am aware that I should't be connecting non host port to 2K FEX but it's corner case. I have done similar setup with Access Port configuration and didn't faced any issues.
Nexus 5K config Config
interface Ethernet107/1/47
switchport mode trunk
switchport trunk allowed vlan 500-501
spanning-tree guard root
spanning-tree bpdufilter enable
interface Ethernet108/1/47
switchport mode trunk
switchport trunk allowed vlan 500-501
spanning-tree guard root
spanning-tree bpdufilter enable
2960-Config
interface GigabitEthernet1/0/47
switchport mode trunk
switchport trunk allowed vlan 500-501
spanning-tree bpdufilter enable
interface GigabitEthernet1/0/48
switchport mode trunk
switchport trunk allowed vlan 500-501
spanning-tree bpdufilter enable
Error Log
%FWM-2-STM_LOOP_DETECT: Loops detected in the network for mac 001b.1700.0130 among ports Eth107/1/47
Eth108/1/47 vlan 500 - Disabling dynamic learn notifications for 180 seconds
Should I configure port as "spanning-tree port type network" and create VPC and "storm-control broadcast level" to stop future occurrence? OR Do i have to configure anything else to prevent spanning-tree loops?
Thanks for your help
RiteshHi,
spanning-tree port type network is used for VPC peer-link. Try creating a new VPC and add ports 107/1/47 and 108/1/47 to it and a Portchannel on the 2960 and test.
HTH -
Cisco 2960S FPS-L PoE switch with Avaya 9811g VOIP setup
Hello,
I am connecting a setup for data/voice connecting Catalyst 2960S-FPS-L PoE switch with Avaya 9811g series VOIP phone. As per my knowledge cisco switch works well with Cisco phone as it has got some builtin "Macros" and Intelligent PoE recognition when we connect device getting the details of another device through CDP. I understand I have to create data and voice vlan with QOS then enable trunking on the interface to other switch that is also 2960. Little confuse if is there any compatibility issues with Switch and Avaya phone regarding protocol/data/voice...?
Do I have to do PoE config for each port on the each interface?
any help or detail config will help.
Thanks in advance.Hi I am back after good research. created two vlan data and voice with trunk on interface1/0/48 given below config..
connection b/w 2960s FPS Switch and Avaya 9611g IP Phone.
lldp/cdp is enable on switch
So I created this config if some one can take a look .
expert advise if something wrong?..
I am only concern with Voice and PoE as voice is my priority. do i have to map something for voice quality?
also if i create another Trunk port one allow voice other allow data both cable will go to switch will that be issue?
interface....
switchport access vlan x
switchport mode access
switchport nonegotiate
switchport voice vlan xx
srr-queue bandwidth share 10 10 60 20
queue-set 2
priority-queue out
mls qos trust cos
auto qos voip trust
spanning-tree portfast
interface ........
switchport trunk allowed vlan x,x
switchport mode trunk
switchport nonegotiate
srr-queue bandwidth share 10 10 60 20
queue-set 2
priority-queue out
mls qos trust cos
auto qos voip trust -
Configuring Port Channel on Cisco 2960S-48LPS-L
When I try to move port channel connections to two of the SFP ports on our Cisco 2960S switch, one of the connections fail.
I am using two GBics, both are the same, GLC-T-A 1000Base-T.
The port channel work fine when I use g1/0/47 and 48.
The port channel work fine when using g1/0/48 and SFP 1/0/49
Port channel does not work when using SFP 1/0/49 and SFP 1/0/50.Cisco C2960S software version: 12.2(55)SE7. Using C2960S-UNIVERSALK9-M.
Port configurations for g1/0/48 - 51:
interface GigabitEthernet1/0/49
description Trunk to Cisco Core
switchport mode trunk
srr-queue bandwidth share 1 30 35 5
priority-queue out
mls qos trust cos
macro description cisco-switch
auto qos trust
spanning-tree link-type point-to-point
channel-group 2 mode on
When working, both ports show green status lights.
ort Name Status Vlan Duplex Speed Type
Po2 Trunk to Core connected trunk a-full a-1000
*: interface is up
IHQ: pkts in input hold queue IQD: pkts dropped from input queue
OHQ: pkts in output hold queue OQD: pkts dropped from output queue
RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)
TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)
TRTL: throttle count
Interface IHQ IQD OHQ OQD RXBS RXPS TXBS TXPS TRTL
* Port-channel2 0 0 0 0 8390000 909 970000 551 0
Age of the Port-channel = 0d:10h:57m:35s
Logical slot/port = 5/2 Number of ports = 2
GC = 0x00000000 HotStandBy port = null
Port state = Port-channel Ag-Inuse
Protocol = -
Port security = Disabled
Ports in the Port-channel:
Index Load Port EC state No of bits
------+------+------+------------------+-----------
0 00 Gi1/0/47 On 0
0 00 Gi1/0/49 On 0
When not working, one port shows green, then other port status light is off.
GigabitEthernet1/0/49 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 3c0e.233f.a531 (bia 3c0e.233f.a531)
Description: Trunk to Cisco Core
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Full-duplex, 1000Mb/s, link type is auto, media type is 10/100/1000BaseTX SFP
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:09, output 00:00:19, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 1954000 bits/sec, 213 packets/sec
5 minute output rate 38000 bits/sec, 16 packets/sec
2935639 packets input, 880524431 bytes, 0 no buffer
Received 2211794 broadcasts (310067 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 310067 multicast, 0 pause input
0 input packets with dribble condition detected
370489 packets output, 66729219 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
GigabitEthernet1/0/50 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet, address is 3c0e.233f.a532 (bia 3c0e.233f.a532)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Auto-duplex, Auto-speed, link type is auto, media type is Not Present
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
--More-- 0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
Let me know if you need more info. -
Cisco 2960-X & ISE accounting- username Radius attribute missing
Hi,
I'm facing an issue with cisco 2960 switch radius accounting with Cisco ISE1.2.1 .here is my senario:
- Username (vendor1) is configured in ISE local database, under group (VENDOR)
- Authentication protocol : wired MAB
- Authentication method : webauth using guest portal , the user is a vendor , so no dot1x configured on his NIC .
the problem is that , the switch is not sending the username as a part of radius attribute , in the authentication log , the username shown as the MAC address of the user machine , therefor , I can not configure my authorization condition using internaluser:Name Equal vendor1
while if I configure the condition using the identity group condition IdentityGroup:Name Equal VENDOR , it works .
The same configuration is working on 3750 switch with no issue .
Here is my Switch config:
aaa authentication login default local
aaa authentication dot1x default group radius
aaa authorization network default group radius
aaa authorization auth-proxy default group radius
aaa accounting auth-proxy default start-stop group radius
aaa accounting dot1x default start-stop group radius
aaa accounting update periodic 5
username admin password
username radius-test password
aaa server radius dynamic-author
client 172.16.2.20 server-key 7 04490A0206345F450C00
client 172.16.2.21 server-key 7 03165A0F0F1A32474B10
radius server ISE-RADIUS-1
address ipv4 172.16.2.20 auth-port 1812 acct-port 1813
automate-tester username radius-test idle-time 15
key 7 111B18011E0718070133
radius server ISE-RADIUS-2
address ipv4 172.16.2.21 auth-port 1812 acct-port 1813
automate-tester username radius-test idle-time 15
key 7 0214055F02131C2A4957
radius-server attribute 6 on-for-login-auth
radius-server attribute 8 include-in-access-req
radius-server attribute 25 access-request include
radius-server attribute 31 mac format ietf upper-case
radius-server attribute 31 send nas-port-detail
radius-server dead-criteria time 5 tries 3
radius-server vsa send accounting
radius-server vsa send authentication
any help !!!Thanks for your reply , I know what's MAB , if you read my explanation again , i mentioned that the user is authenticated in the guest portal which mean that I have web authentication , and it is working fine .. The only issue is that I can not use the vendor1 username as part of authorization condition and this is because the switch is not sending the radius attribute type 1 to the ISE , thus , on the ise authentication log the MAC address of the client machine is shown as a username not the actual username ( vendor1)
as I mentioned also , I have exactly the same setup with ise 1.2 and 3750 switch and I do not have this issue .I experience this with 2960x only . -
How many clients can connect through cisco AP 1310 in wireless network ?
I had setup wireless network with
wlc4402,cisco AP 1310.1131 and 1242 and Cisco acs 4.1.My problem is only 30 clients connect through Cisco AP 1310 at a time.I can not connect more than 30 clients at a time.What is the issue in wireless network?please reply .
Thanks and regards
By
D.AnbuduraiWIRELESS > 802.11 > RRM
How can do that setting ? Can you reply with
some brief steps? And also I want to know how
many clients can connect in wireless network at
a time exactly through cisco aps?
Thanks and regards
d.anbudurai -
I am working on putting a loaner ASR 1001 into my infrastructure to replace my 7206 VXR. Currently my uplink to my ISP is fiber and runs into an GBIC SX MM transceiver. No issue with connectivity. When i change the fiber patch over to LC I connect it to the ASR 1001 GBIC and I get no link. Tried changed negotiation auto to no negotiation auto not affect. I then took the fiber and connected to a gbic I have in a 3560 switch link comes right up. At this point I am a bit stumped. Tried moving the configuration to a different interface on the ASR no luck. Totally confused.
What model transceiver are you using on the ASR? I didn't tink they took GBICs - ony SFPs. I think the one you would need is an SFP (the GLC-SX-MMD or GLC-SX-MM without DOM). That's what's compatible on an ASR 1001 for 1 Gbps MM fiber per the compatibility matrix.
Is the ASR recognizing the transceiver? (show int ___)
Maybe you are looking for
-
Hi Noticed that the top of my mac is nearly too hot to touch. Did a search online and found out about the hardware test. Looked up online user manual for my mac (Processor 3.06 GHz Intel Core 2 Duo 10.8.4) and noted how to perform the test. Howe
-
No Software update on Mac OS X 10.5.8
I haven't had a software update on my Mac OS X 10.5.8 in about a year. Every time I click on software update, it just says that there are no software updates at this time. Help
-
Why don't my contacts sort onto the alpha pages of the Contacts app?
New iPad. I'm entering contacts into the Contacts apps included. But they are all on one page with the alpha letter divider between the sections
-
Is it Possible to Make a Flash Playable DVD for the iTouch
Is it possible to make the same kind of "virtual" DVD player file in Encore for an iTouch audience that works like the Flash output in Encore? I am under the impression that the 3G iTouch can play flash files but if that is not correct then I guess m
-
Print Servers Impact after unicode conversion
Hi We are performing an CUUC from 4.6C to ECC 6.0 Our customer has around 4-5 windows special print servers which are used for chinese, japanese, korean printing..etc. After the upgrade & unicode conversion - Do we still need to use all these 4-5 spe