SFP module strange behavior
Hello!
I have cisco-finisar 1Gig module installed in SFP port in RSP720-3CXL-GE.
Here is some diag:
core2#sh idprom interface gigabitEthernet 6/1 detail
<cut>
Transceiver Serial EEPROM Contents:
Common block:
Identifier :
Connector : [0x07]
Transceiver
Speed : [0x00]
Media : [0x00]
Technology : [0x00]
Link Length : [0x02]
GE Comp Codes : 1000BASE-LX [0x12]
SONET Comp Codes : [0x00]
Encoding : 8B10B [0x01]
BR, Nominal : 21x100 MHz [0x15]
Length(9u) : 100 x 100 m [0x64]
Length(50u) : 0 x 10 m [0x00]
Length(62.5u) : 0 x 10 m [0x00]
Length(Copper) : 0 m [0x00]
Vendor Name : CISCO-FINISAR
Vendor OUI : 0x0 0x90 0x65
Vendor PN : FTRJ1319P1BTL-C5
Vendor rev : 10.0
CC_BASE : 0x99
Extended ID Fields
Options : Loss of Signal implemented TX_DISABLE is implemented and disables the serial output
BR, max : Unspecified
BR, min : Unspecified
Vendor SN : FNS11360P14
Date code : 061212
CC_EXT : 0x8D
The strange thing about it is that when observing transiever status I see the flap of that kind:
core2#sh interfaces transceiver | i Gi6/1
Gi6/1 0.0 0.00 0.0 -40.0 -40.0
core2#sh interfaces transceiver | i Gi6/1
Gi6/1 0.7 0.01 -- 0.3 -- N/A ++ -40.0
I could guess that this is the power problem, perhaps sfp module installed badly or the transmitter is out of service.
But..the magic is that the interface is operational, trafic flows and no threshold messages are dropped into log:
core2#sh int gigabitEthernet 6/1
GigabitEthernet6/1 is up, line protocol is up (connected)
Hardware is c7600 1Gb 802.3, address is 001c.584c.556c (bia 001c.584c.556c)
Description: peer
MTU 9000 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 46/255, rxload 70/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is LH
input flow-control is off, output flow-control is off
Clock mode is auto
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters 17w6d
Input queue: 0/2000/1255/0 (size/max/drops/flushes); Total output drops: 118
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 276684000 bits/sec, 47459 packets/sec
5 minute output rate 183261000 bits/sec, 50184 packets/sec
946156131401 packets input, 670142539615934 bytes, 0 no buffer
Received 181011 broadcasts (179518 multicasts)
0 runts, 0 giants, 0 throttles
25 input errors, 22 CRC, 3 frame, 1255 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
1020707481696 packets output, 452456257677017 bytes, 0 underruns
0 output errors, 0 collisions, 5 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
So...is it some bug with all finisar modules, or it is a module frome a corrupted production set, or it is an IOS bug of "sh interface transiever" command ?
Any ideas?
Thanks in advance.
From my post it is evident that I use either SM or MM capable trnasiever (1000BASE-LX/LH)
My trnasiever is anyway operational though indication is incorrect.
Perhaps, you (and I) should look for other than Finisar transiever vendor, compartible with cisco
Look for where the transiever was manufactured. Better it is Japan, not Malayasia or China.
Similar Messages
-
Report FP_TEST_00 - Strange behavior
Hello Gurus,
A strange behavior with report FP_TEST_00 occurs:
SA38 --> FP_TEST_00 --> select a device --> execute --> print preview then and error or popup is show:
Adobe Reader
Error initializing the font server module
Then the SAP GUI is closed, I check the ST22 and no dump is generated and in transaction SM21 only appear:
DP Q0 4 Connection to user 551 (ADMIN ), terminal 86 (HUSVP-SAP-BA) lost
DP Q0 I Operating system call recv failed (error no. 232 )
The #1 log entry: *
Details Page 2 Line 28 System Log: Local Analysis of sapdev 1
Time Type Nr Clt User TCode Grp N Text
11:37:20 DP Q0 4 Connection to user 551 (ADMIN ), terminal 86 (HUSVP-SAP-BA) lost
Connection to user 551 (ADMIN ), terminal 86 (HUSVP-SAP-BA) lost
Details
Recording at local and central time........................ 25.02.2010 11:37:20
Task...... Process User...... Terminal Session TCode Program Cl Problem cl Package
11092 Dispatcher K SAP Web AS Problem STSK
Further details for this message type
Module nam Line Error text.......... Caller.... Reason/cal
dpxxdisp 1223 551 ADMIN 86 HUSVP-SAP-BA DpRTmPr NiBufRe
Documentation for system log message Q0 4 :
The SAP Dispatcher (part of the application server) has lost the
connection to a terminal process. For example, this happens when the
terminal program (GUI) terminates without correctly logging off the
application server. More detailed information about the error
context is not available here.
Technical details
File Offset RecFm System log type Grp N variable message data
21 254340 m Error (Function,Module,Row) Q0 4 551 ADMIN 86 HUSVP-SAP-BA DpRTmPrNiBufRedpxxdisp1223
The #2 Log show: *
Details Page 2 Line 29 System Log: Local Analysis of sapdev 1
Time Type Nr Clt User TCode Grp N Text
11:37:20 DP Q0 I Operating system call recv failed (error no. 232 )
Operating system call recv failed (error no. 232 )
Details
Recording at local and central time........................ 25.02.2010 11:37:20
Task...... Process User...... Terminal Session TCode Program Cl Problem cl Package
11092 Dispatcher K SAP Web AS Problem STSK
Further details for this message type
Module nam Line Error text Caller.... Reason/cal
nixxi.cp 4435 recv232 NiIRead recv
Documentation for system log message Q0 I :
The specified operating system call was returned with an error.
For communication calls (receive, send, etc) often the cause of errors
are network problems.
It could also be a configuration problem at operating system level.
(file cannot be opened, no space in the file system etc.).
Additional specifications for error number 232
Name for errno number ECONNRESET
No documentation available for error ECONNRESET
Technical details
File Offset RecFm System log type Grp N variable message data
21 254520 m Error (Function,Module,Row) Q0 I recv232 NiIReadrecv nixxi.cp4435
Edited by: Hernando Polania Cadena on Feb 25, 2010 8:36 PMHello All,
I applied the solution in page
http://wiki.sdn.sap.com/wiki/display/PLM/Adobe%209%20-%20SAPGUI%20crash
Works OK
Thanks
Hernando -
Strange behavior in deleting images - works on second but not first try
In Library mode, Grid view, right after importing, after I select several images with an "x" to be deleted, when I bring up the "Delete Rejected Photos" dialog, I find this strange behavior. I get the message that there are not photos marked for deletion. I then invoke the dialog again, and my photos that were marked show up, with the choices of deleting from disk or removing from the catalog. What am I likely doing wrong? I'm on WinXP Pro with LR 2.2. Thanks!
DilipDilip,
I too have seen this behaviour in all versions of LR. Even when deleting a single image in the develop module. If LR is writting the preview you can't delete the file until the preview is rendered. I think it's more to do with the OS not allowing the deletion of a file being accessed than a LR bug as such.
Gordon -
Strange behavior of flex4 service call
Hi Techies, I am stuck with strange behavior of flex4 service call. Our is a dashboard application where i have four modules(separae file for each) in a page. when page renders all these modules makes separate service call through remote objects. Though destination file is same but methods are separate for each modules. db+java takes 5 second for 1 and 3 module, 9 seconds for third module and 15 seconds for 4th module. Sinch LCDS calls are asynchronous ideally after 5 seconds module 1 and 2 should display data. similarly for 3rd module after 9seconds. For my wonder it doesnt go this way. data for all the modules appears simultaneously after 15-16 seconds. It behaves like when data for all the modules is available then only it populates charts and grids. Looks like call is being made in sequence and once maximum taking method is done then control returns back to flex. Any pointer will be helpful to improvise this.
Thanks,
RohitHi Techies, I am stuck with strange behavior of flex4 service call. Our is a dashboard application where i have four modules(separae file for each) in a page. when page renders all these modules makes separate service call through remote objects. Though destination file is same but methods are separate for each modules. db+java takes 5 second for 1 and 3 module, 9 seconds for third module and 15 seconds for 4th module. Sinch LCDS calls are asynchronous ideally after 5 seconds module 1 and 2 should display data. similarly for 3rd module after 9seconds. For my wonder it doesnt go this way. data for all the modules appears simultaneously after 15-16 seconds. It behaves like when data for all the modules is available then only it populates charts and grids. Looks like call is being made in sequence and once maximum taking method is done then control returns back to flex. Any pointer will be helpful to improvise this.
Thanks,
Rohit -
Cropping LR4 occasional strange behavior experienced by others?
The LR4 cropping process has become unstable during use on several occasions. The LR4 cropping tool seems to get confused.
During the cropping process, unwanted changes to position and leveling of the cropped area happen upon exiting. The cropped image one saw immediately before exiting is not what one sees afterwards. The crop has changed on its own. During the episode, the response to the mouse is not normal. One may drag the corner only to have it spring back upon release of the button.
Exiting LR4 and reentering does not cure the behavior. One must open image in Develop module, restore crop defaults, exit, and reenter batch tool to restore normal behavior. I am not certain as to the exact order of these steps but essentially normalcy was restored during their implementation.
I have notice that this abnormal behavior seems more likely to occur during sessions when I am making use of the "Previous" button.
As far as I know, the behavior is not reproducible. It occurs during some of those late night sessions and I have not documented it well but will do so if we don’t have a cure by next time it occurs.
My configuration:
Lightroom version: 4.2 [850741]
Operating system: Windows 7 Ultimate Edition
Version: 6.1 [7601]
Application architecture: x64
System architecture: x64
Physical processor count: 8
Processor speed: 3.3 GHz
Built-in memory: 16364.3 MB
Real memory available to Lightroom: 16364.3 MB
Real memory used by Lightroom: 1066.6 MB (6.5%)
Virtual memory used by Lightroom: 1090.4 MB
Memory cache size: 0.0 MB
System DPI setting: 96 DPI
Desktop composition enabled: Yes
Displays: 1) 1920x1080Replacing the Lr preference file may help. The preference file can go "funny" and then causes all kinds of strange behavior of Lr.
Replacing the preference file takes about 10 minutes, and you don`t need to re-install Lr.
BTW: Un-installing and re-installing Lr does not replace the preference file.
See here for instructions o how to replace the preference file: http://lightroomers.com/replacing-the-lightroom-preference-file/745/
See here where to find the preference file: http://helpx.adobe.com/lightroom/kb/preference-file-locations-lightroom-4.html -
Strange behavior after suspend.
Hi,
For some time I have a strange behavior of my system after I awake my computer(after suspend). This problem don't disappear after update.
Ok, so if I suspend my computer, and awake him I can't run any program. Even if i was open some application, this application crashes. I have to restart my machine.
Somebody had similar problem or know how help?
I'm using Arch Linux x64, kernel 3.8, openbox. Suspend by "systemctl suspend".OK, maybe good idea is paste here my output journal:
# journalctl --since=today | tac | sed -n '/-- Reboot --/{n;:r;/-- Reboot --/q;p;n;b r}' | tac
-- Logs begin at Mon 2012-09-10 20:20:07 CEST, end at Thu 2013-03-28 10:17:18 CET. --
Mar 28 10:10:36 localhost kernel: Freezing user space processes ... (elapsed 0.01 seconds) done.
Mar 28 10:10:36 localhost systemd[1]: Time has been changed
Mar 28 10:10:36 localhost systemd[1]: systemd-tmpfiles-clean.timer: time change, recalculating next elapse.
Mar 28 10:10:36 localhost kernel: Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Mar 28 10:10:36 localhost dhcpcd[1435]: eth1: carrier lost
Mar 28 10:10:36 localhost kernel: PM: Entering mem sleep
Mar 28 10:10:36 localhost kernel: Suspending console(s) (use no_console_suspend to debug)
Mar 28 10:10:36 localhost kernel: sd 0:0:0:0: [sda] Synchronizing SCSI cache
Mar 28 10:10:36 localhost kernel: sd 0:0:0:0: [sda] Stopping disk
Mar 28 10:10:36 localhost kernel: cfg80211: Calling CRDA for country: PL
Mar 28 10:10:36 localhost kernel: <6>[fglrx] IRQ 46 Disabled
Mar 28 10:10:36 localhost kernel: <6>[fglrx] Preparing suspend fglrx in kernel.
Mar 28 10:10:36 localhost kernel: <6>[fglrx] Suspending fglrx in kernel completed.
Mar 28 10:10:36 localhost kernel: <6>[fglrx] Power down the ASIC .
Mar 28 10:10:36 localhost kernel: PM: suspend of devices complete after 1126.292 msecs
Mar 28 10:10:36 localhost kernel: PM: late suspend of devices complete after 0.263 msecs
Mar 28 10:10:36 localhost kernel: r8169 0000:09:00.0: System wakeup enabled by ACPI
Mar 28 10:10:36 localhost kernel: ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
Mar 28 10:10:36 localhost kernel: PM: noirq suspend of devices complete after 52.988 msecs
Mar 28 10:10:36 localhost kernel: ACPI: Preparing to enter system sleep state S3
Mar 28 10:10:36 localhost kernel: PM: Saving platform NVS memory
Mar 28 10:10:36 localhost kernel: Disabling non-boot CPUs ...
Mar 28 10:10:36 localhost kernel: smpboot: CPU 1 is now offline
Mar 28 10:10:36 localhost kernel: smpboot: CPU 2 is now offline
Mar 28 10:10:36 localhost kernel: smpboot: CPU 3 is now offline
Mar 28 10:10:36 localhost kernel: Extended CMOS year: 2000
Mar 28 10:10:36 localhost kernel: ACPI: Low-level resume complete
Mar 28 10:10:36 localhost kernel: PM: Restoring platform NVS memory
Mar 28 10:10:36 localhost kernel: Extended CMOS year: 2000
Mar 28 10:10:36 localhost kernel: CPU0: Thermal monitoring handled by SMI
Mar 28 10:10:36 localhost kernel: Enabling non-boot CPUs ...
Mar 28 10:10:36 localhost kernel: smpboot: Booting Node 0 Processor 1 APIC 0x4
Mar 28 10:10:36 localhost kernel: CPU1: Thermal monitoring handled by SMI
Mar 28 10:10:36 localhost kernel: CPU1 is up
Mar 28 10:10:36 localhost kernel: smpboot: Booting Node 0 Processor 2 APIC 0x1
Mar 28 10:10:36 localhost kernel: CPU2: Thermal monitoring handled by SMI
Mar 28 10:10:36 localhost kernel: CPU2 is up
Mar 28 10:10:36 localhost kernel: smpboot: Booting Node 0 Processor 3 APIC 0x5
Mar 28 10:10:36 localhost kernel: CPU3: Thermal monitoring handled by SMI
Mar 28 10:10:36 localhost kernel: CPU3 is up
Mar 28 10:10:36 localhost kernel: ACPI: Waking up from system sleep state S3
Mar 28 10:10:36 localhost kernel: ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
Mar 28 10:10:36 localhost kernel: sdhci-pci 0000:07:00.0: MMC controller base frequency changed to 50Mhz.
Mar 28 10:10:36 localhost kernel: sdhci-pci 0000:07:00.0: proprietary Ricoh MMC controller disabled (via firewire function)
Mar 28 10:10:36 localhost kernel: sdhci-pci 0000:07:00.0: MMC cards are now supported by standard SDHCI controller
Mar 28 10:10:36 localhost kernel: PM: noirq resume of devices complete after 133.780 msecs
Mar 28 10:10:36 localhost kernel: PM: early resume of devices complete after 0.127 msecs
Mar 28 10:10:36 localhost kernel: ehci-pci 0000:00:1a.0: setting latency timer to 64
Mar 28 10:10:36 localhost kernel: mei 0000:00:16.0: irq 43 for MSI/MSI-X
Mar 28 10:10:36 localhost kernel: snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X
Mar 28 10:10:36 localhost kernel: pci 0000:00:1e.0: setting latency timer to 64
Mar 28 10:10:36 localhost kernel: ehci-pci 0000:00:1d.0: setting latency timer to 64
Mar 28 10:10:36 localhost kernel: ahci 0000:00:1f.2: setting latency timer to 64
Mar 28 10:10:36 localhost kernel: snd_hda_intel 0000:02:00.1: irq 45 for MSI/MSI-X
Mar 28 10:10:36 localhost kernel: r8169 0000:09:00.0: System wakeup disabled by ACPI
Mar 28 10:10:36 localhost kernel: <6>[fglrx] Power up the ASIC
Mar 28 10:10:36 localhost kernel: <6>[fglrx] Preparing resume fglrx in kernel.
Mar 28 10:10:36 localhost kernel: Extended CMOS year: 2000
Mar 28 10:10:36 localhost kernel: <6>[fglrx] Resuming fglrx in kernel completed.
Mar 28 10:10:36 localhost kernel: <6>[fglrx] IRQ 46 Enabled
Mar 28 10:10:36 localhost kernel: ata5: SATA link down (SStatus 0 SControl 300)
Mar 28 10:10:36 localhost kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Mar 28 10:10:36 localhost kernel: ata2.00: configured for UDMA/100
Mar 28 10:10:36 localhost kernel: usb 2-1.3: reset low-speed USB device number 3 using ehci-pci
Mar 28 10:10:36 localhost kernel: sdhci-pci 0000:07:00.0: Will use DMA mode even though HW doesn't fully claim to support it.
Mar 28 10:10:36 localhost kernel: firewire_core 0000:07:00.3: rediscovered device fw0
Mar 28 10:10:36 localhost kernel: usb 1-1.4: reset high-speed USB device number 3 using ehci-pci
Mar 28 10:10:36 localhost kernel: ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 28 10:10:36 localhost kernel: ata1.00: configured for UDMA/133
Mar 28 10:10:36 localhost kernel: sd 0:0:0:0: [sda] Starting disk
Mar 28 10:10:36 localhost kernel: PM: resume of devices complete after 2478.795 msecs
Mar 28 10:10:36 localhost kernel: PM: Finishing wakeup.
Mar 28 10:10:36 localhost kernel: Restarting tasks ... done.
Mar 28 10:10:36 localhost kernel: video LNXVIDEO:00: Restoring backlight state
Mar 28 10:10:36 localhost slim[806]: Conky: can't open /sys/class/power_supply/BAT0/uevent: No such file or directory
Mar 28 10:10:36 localhost slim[806]: Conky: can't open /proc/acpi/battery/BAT0/state: No such file or directory
Mar 28 10:10:36 localhost systemd-sleep[4208]: System resumed.
Mar 28 10:10:36 localhost dbus-daemon[800]: dbus[800]: [system] Activating via systemd: service name='org.freedesktop.UPower' unit='upower.service'
Mar 28 10:10:36 localhost dbus[800]: [system] Activating via systemd: service name='org.freedesktop.UPower' unit='upower.service'
Mar 28 10:10:36 localhost su[4307]: (to root) root on none
Mar 28 10:10:36 localhost su[4307]: pam_unix(su:session): session opened for user root by (uid=0)
Mar 28 10:10:36 localhost systemd[1]: Starting Daemon for power management...
Mar 28 10:10:36 localhost su[4307]: pam_unix(su:session): session closed for user root
Mar 28 10:10:36 localhost su[4328]: (to root) root on none
Mar 28 10:10:36 localhost su[4328]: pam_unix(su:session): session opened for user root by (uid=0)
Mar 28 10:10:36 localhost su[4328]: pam_unix(su:session): session closed for user root
Mar 28 10:10:36 localhost systemd[1]: Started Suspend.
Mar 28 10:10:36 localhost systemd[1]: Service sleep.target is not needed anymore. Stopping.
Mar 28 10:10:36 localhost systemd[1]: Stopping Sleep.
Mar 28 10:10:36 localhost systemd[1]: Stopped target Sleep.
Mar 28 10:10:36 localhost systemd[1]: Starting Suspend.
Mar 28 10:10:36 localhost systemd[1]: Reached target Suspend.
Mar 28 10:10:36 localhost systemd-logind[796]: Operation finished.
Mar 28 10:10:36 localhost laptop-mode[4441]: Laptop mode
Mar 28 10:10:36 localhost laptop-mode[4446]: enabled, active [unchanged]
Mar 28 10:10:36 localhost logger[4463]: ACPI action undefined: ACPI0003:00
Mar 28 10:10:36 localhost laptop-mode[4501]: Laptop mode
Mar 28 10:10:36 localhost laptop-mode[4509]: enabled, active [unchanged]
Mar 28 10:10:36 localhost laptop-mode[4534]: Laptop mode
Mar 28 10:10:36 localhost laptop-mode[4539]: enabled, active [unchanged]
Mar 28 10:10:36 localhost laptop-mode[4554]: Laptop mode
Mar 28 10:10:36 localhost laptop-mode[4557]: enabled, active [unchanged]
Mar 28 10:10:36 localhost laptop-mode[4562]: Laptop mode
Mar 28 10:10:36 localhost laptop-mode[4563]: enabled, active [unchanged]
Mar 28 10:10:36 localhost dbus-daemon[800]: dbus[800]: [system] Successfully activated service 'org.freedesktop.UPower'
Mar 28 10:10:36 localhost dbus[800]: [system] Successfully activated service 'org.freedesktop.UPower'
Mar 28 10:10:36 localhost systemd[1]: Started Daemon for power management.
Mar 28 10:10:37 localhost ntpd[1442]: Deleting interface #3 eth1, 192.168.1.6#123, interface stats: received=135, sent=135, dropped=1, active_time=4197 secs
Mar 28 10:10:37 localhost ntpd[1442]: 149.156.70.60 interface 192.168.1.6 -> (none)
Mar 28 10:10:37 localhost ntpd[1442]: 149.156.24.40 interface 192.168.1.6 -> (none)
Mar 28 10:10:37 localhost ntpd[1442]: 46.250.172.2 interface 192.168.1.6 -> (none)
Mar 28 10:10:37 localhost ntpd[1442]: peers refreshed
Mar 28 10:10:38 localhost su[4624]: (to root) root on none
Mar 28 10:10:38 localhost su[4624]: pam_unix(su:session): session opened for user root by (uid=0)
Mar 28 10:10:38 localhost laptop-mode[4653]: Laptop mode
Mar 28 10:10:38 localhost laptop-mode[4654]: enabled, active [unchanged]
Mar 28 10:10:38 localhost dhcpcd[1435]: eth1: carrier acquired
Mar 28 10:10:38 localhost dhcpcd[1435]: eth1: sending IPv6 Router Solicitation
Mar 28 10:10:38 localhost dhcpcd[1435]: eth1: rebinding lease of 192.168.1.6
Mar 28 10:10:38 localhost dhcpcd[1435]: eth1: acknowledged 192.168.1.6 from 192.168.1.1 `TP-LINK'
Mar 28 10:10:38 localhost dhcpcd[1435]: eth1: checking for 192.168.1.6
Mar 28 10:10:38 localhost su[4624]: pam_unix(su:session): session closed for user root
Mar 28 10:10:38 localhost su[4660]: (to root) root on none
Mar 28 10:10:38 localhost su[4660]: pam_unix(su:session): session opened for user root by (uid=0)
Mar 28 10:10:38 localhost su[4660]: pam_unix(su:session): session closed for user root
Mar 28 10:10:38 localhost kernel: EXT4-fs (sda6): re-mounted. Opts: commit=0
Mar 28 10:10:38 localhost kernel: EXT4-fs (sda7): re-mounted. Opts: commit=0
Mar 28 10:10:38 localhost laptop-mode[4694]: Laptop mode
Mar 28 10:10:38 localhost laptop-mode[4695]: enabled, active [unchanged]
Mar 28 10:10:38 localhost logger[4698]: ACPI action undefined: ACPI0003:00
Mar 28 10:10:38 localhost slim[806]: tint2 : invalid option "task_margin",
Mar 28 10:10:38 localhost slim[806]: upgrade tint2 or correct your config file
Mar 28 10:10:38 localhost slim[806]: tint2 : nb monitor 1, nb monitor used 1, nb desktop 1
Mar 28 10:10:38 localhost slim[806]: X Error of failed request: BadWindow (invalid Window parameter)
Mar 28 10:10:38 localhost slim[806]: Major opcode of failed request: 21 (X_ListProperties)
Mar 28 10:10:38 localhost slim[806]: Resource id in failed request: 0x18000b0
Mar 28 10:10:38 localhost slim[806]: Serial number of failed request: 12
Mar 28 10:10:38 localhost slim[806]: Current serial number in output stream: 12
Mar 28 10:10:40 localhost slim[806]: you have no weather alerts
Mar 28 10:10:40 localhost slim[806]: processing complete
Mar 28 10:10:40 localhost slim[806]: gathering data with curl
Mar 28 10:10:40 localhost slim[806]: % Total % Received % Xferd Average Speed Time Time Time Current
Mar 28 10:10:40 localhost slim[806]: Dload Upload Total Spent Left Speed
Mar 28 10:10:40 localhost slim[806]: 0 0 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0curl: (6) Could not resolve host: (nil); Unknown error
Mar 28 10:10:40 localhost slim[806]: not checking for alerts
Mar 28 10:10:40 localhost slim[806]: curl attempt timed out, trying again
Mar 28 10:10:40 localhost slim[806]: % Total % Received % Xferd Average Speed Time Time Time Current
Mar 28 10:10:40 localhost slim[806]: Dload Upload Total Spent Left Speed
Mar 28 10:10:40 localhost slim[806]: 0 0 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0curl: (6) Could not resolve host: (nil); Unknown error
Mar 28 10:10:42 localhost dhcpcd[1435]: eth1: sending IPv6 Router Solicitation
Mar 28 10:10:43 localhost dhcpcd[1435]: eth1: leased 192.168.1.6 for 259200 seconds
Mar 28 10:10:45 dhcppc4 ntpd[1442]: Listen normally on 6 eth1 192.168.1.6 UDP 123
Mar 28 10:10:45 dhcppc4 ntpd[1442]: peers refreshed
Mar 28 10:10:45 dhcppc4 ntpd[1442]: new interface(s) found: waking up resolver
Mar 28 10:10:45 dhcppc4 slim[806]: Traceback (most recent call last):
Mar 28 10:10:45 dhcppc4 slim[806]: File "/home/rlk120/.scripts/gmail.py", line 9, in <module>
Mar 28 10:10:45 dhcppc4 slim[806]: msg=temp.read()
Mar 28 10:10:45 dhcppc4 slim[806]: File "/usr/lib/python3.3/encodings/ascii.py", line 26, in decode
Mar 28 10:10:45 dhcppc4 slim[806]: return codecs.ascii_decode(input, self.errors)[0]
Mar 28 10:10:45 dhcppc4 slim[806]: UnicodeDecodeError: 'ascii' codec can't decode byte 0xc5 in position 375: ordinal not in range(128)
Mar 28 10:10:45 dhcppc4 slim[806]: not checking for alerts
Mar 28 10:10:45 dhcppc4 slim[806]: curl attempt timed out, trying again
Mar 28 10:10:45 dhcppc4 slim[806]: % Total % Received % Xferd Average Speed Time Time Time Current
Mar 28 10:10:45 dhcppc4 slim[806]: Dload Upload Total Spent Left Speed
Mar 28 10:10:46 dhcppc4 slim[806]: [234B blob data]
Mar 28 10:10:46 dhcppc4 dhcpcd[1435]: eth1: sending IPv6 Router Solicitation
Mar 28 10:10:50 dhcppc4 dhcpcd[1435]: eth1: sending IPv6 Router Solicitation
Mar 28 10:10:50 dhcppc4 dhcpcd[1435]: eth1: no IPv6 Routers available
Mar 28 10:11:03 dhcppc4 slim[806]: No protocol specified
Mar 28 10:11:03 dhcppc4 slim[806]: (chromium:4750): Gtk-WARNING **: cannot open display: :0.0
Mar 28 10:11:31 dhcppc4 systemd-logind[796]: System is rebooting.
Mar 28 10:11:32 dhcppc4 systemd[1]: Deactivating swap /dev/sda8...
Mar 28 10:11:32 dhcppc4 systemd[1]: Deactivating swap /dev/sda8...
Mar 28 10:11:32 dhcppc4 systemd[1]: Deactivating swap /dev/sda8...
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Sound Card.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopped target Sound Card.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Daemon for power management...
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Authorization Manager...
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Graphical Interface.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopped target Graphical Interface.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Multi-User.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopped target Multi-User.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping ACPI event daemon...
Mar 28 10:11:32 dhcppc4 ntpd[1442]: ntpd exiting on signal 15
Mar 28 10:11:32 dhcppc4 acpid[793]: exiting
Mar 28 10:11:32 dhcppc4 dhcpcd[4810]: sending signal 1 to pid 1435
Mar 28 10:11:32 dhcppc4 dhcpcd[4810]: waiting for pid 1435 to exit
Mar 28 10:11:32 dhcppc4 dhcpcd[1435]: received SIGHUP, releasing
Mar 28 10:11:32 dhcppc4 dhcpcd[1435]: eth1: releasing lease of 192.168.1.6
Mar 28 10:11:32 dhcppc4 dhcpcd[1435]: eth1: removing interface
Mar 28 10:11:33 dhcppc4 slim[806]: Conky: received SIGHUP or SIGUSR1. reloading the config file.
Mar 28 10:11:33 dhcppc4 slim[806]: XIO: fatal IO error 11 (Resource temporarily unavailable) on X server ":0.0"
Mar 28 10:11:33 dhcppc4 slim[806]: after 200200 requests (200197 known processed) with 0 events remaining.
Mar 28 10:11:33 dhcppc4 slim[806]: Conky: received SIGHUP or SIGUSR1. reloading the config file.
Mar 28 10:11:33 dhcppc4 slim[806]: XIO: fatal IO error 4 (Interrupted system call) on X server ":0.0"
Mar 28 10:11:33 dhcppc4 slim[806]: after 226 requests (226 known processed) with 0 events remaining.
Mar 28 10:11:33 dhcppc4 slim[806]: real transparency off.... depth: 24
Mar 28 10:11:33 dhcppc4 slim[806]: xRandr: Found crtc's: 4
Mar 28 10:11:33 dhcppc4 slim[806]: xRandr: Linking output LVDS with crtc 0
Mar 28 10:11:33 dhcppc4 slim[806]: real transparency off.... depth: 24
Mar 28 10:11:33 dhcppc4 slim[806]: xRandr: Found crtc's: 4
Mar 28 10:11:33 dhcppc4 slim[806]: xRandr: Linking output LVDS with crtc 0
Mar 28 10:11:33 dhcppc4 slim[806]: XIO: fatal IO error 11 (Resource temporarily unavailable) on X server ":0.0"
Mar 28 10:11:33 dhcppc4 slim[806]: after 534585 requests (534585 known processed) with 0 events remaining.
Mar 28 10:11:33 dhcppc4 slim[806]: XIO: fatal IO error 11 (Resource temporarily unavailable) on X server ":0.0"
Mar 28 10:11:33 dhcppc4 slim[806]: after 163909 requests (163909 known processed) with 0 events remaining.
Mar 28 10:11:33 dhcppc4 slim[806]: you have no weather alerts
Mar 28 10:11:33 dhcppc4 slim[806]: processing complete
Mar 28 10:11:33 dhcppc4 kernel: cfg80211: Calling CRDA to update world regulatory domain
Mar 28 10:11:33 dhcppc4 kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Mar 28 10:11:33 dhcppc4 netcfg-daemon[4777]: :: siec_domowa down [done]
Mar 28 10:11:33 dhcppc4 slim[806]: Server terminated successfully (0). Closing log file.
Mar 28 10:11:33 dhcppc4 laptop-mode[4865]: Laptop mode
Mar 28 10:11:33 dhcppc4 laptop-mode[4866]: enabled, active [unchanged]
Mar 28 10:11:34 dhcppc4 systemd[1]: slim.service: main process exited, code=exited, status=1/FAILURE
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped SLiM Simple Login Manager.
Mar 28 10:11:34 dhcppc4 systemd[1]: Unit slim.service entered failed state
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Permit User Sessions...
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Permit User Sessions.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Basic System.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped target Basic System.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Dispatch Password Requests to Console Directory Watch.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Dispatch Password Requests to Console Directory Watch.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Forward Password Requests to Wall Directory Watch.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Forward Password Requests to Wall Directory Watch.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Daily Cleanup of Temporary Directories.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Daily Cleanup of Temporary Directories.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Sockets.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped target Sockets.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping LVM2 metadata daemon socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed LVM2 metadata daemon socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Device-mapper event daemon FIFOs.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed Device-mapper event daemon FIFOs.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Syslog Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed Syslog Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping ACPID Listen Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed ACPID Listen Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping D-Bus System Message Bus Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed D-Bus System Message Bus Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping System Initialization.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped target System Initialization.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Load Kernel Modules...
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Load Kernel Modules.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Apply Kernel Variables...
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Apply Kernel Variables.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Setup Virtual Console...
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped Setup Virtual Console.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Set Up Additional Binary Formats...
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped Set Up Additional Binary Formats.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Encrypted Volumes.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Encrypted Volumes.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Swap.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Swap.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Local File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Local File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Unmounting /home...
Mar 28 10:11:35 dhcppc4 systemd[1]: Unmounting /tmp...
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Remote File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Remote File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Unmounted /tmp.
Mar 28 10:11:35 dhcppc4 systemd[1]: Unmounted /home.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Unmount All Filesystems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Reached target Unmount All Filesystems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Local File Systems (Pre).
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Local File Systems (Pre).
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Remount Root and Kernel File Systems...
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped Remount Root and Kernel File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Shutdown.
Mar 28 10:11:35 dhcppc4 systemd[1]: Reached target Shutdown.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Save Random Seed...
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Update UTMP about System Shutdown...
Mar 28 10:11:35 dhcppc4 systemd[1]: Started Save Random Seed.
Mar 28 10:11:35 dhcppc4 systemd[1]: Started Update UTMP about System Shutdown.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Final Step.
Mar 28 10:11:35 dhcppc4 systemd[1]: Reached target Final Step.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Reboot...
Mar 28 10:11:35 dhcppc4 systemd[1]: Shutting down.
Mar 28 10:11:35 dhcppc4 systemd[1]: Hardware watchdog 'iTCO_wdt', version 0
Mar 28 10:11:35 dhcppc4 systemd[1]: Set hardware watchdog to 10min.
Mar 28 10:11:35 dhcppc4 kernel: watchdog watchdog0: watchdog did not stop!
Mar 28 10:11:35 dhcppc4 systemd-journal[131]: Journal stopped
Somebody probably find interesting things in this code.
And here is some fail slim:
# journalctl /usr/lib/systemd/systemd --since=today
-- Logs begin at Mon 2012-09-10 20:20:07 CEST, end at Thu 2013-03-28 10:37:18 CET. --
Mar 28 10:10:36 localhost systemd[1]: Time has been changed
Mar 28 10:10:36 localhost systemd[1]: systemd-tmpfiles-clean.timer: time change, recalculating next elapse.
Mar 28 10:10:36 localhost systemd[1]: Starting Daemon for power management...
Mar 28 10:10:36 localhost systemd[1]: Started Suspend.
Mar 28 10:10:36 localhost systemd[1]: Service sleep.target is not needed anymore. Stopping.
Mar 28 10:10:36 localhost systemd[1]: Stopping Sleep.
Mar 28 10:10:36 localhost systemd[1]: Stopped target Sleep.
Mar 28 10:10:36 localhost systemd[1]: Starting Suspend.
Mar 28 10:10:36 localhost systemd[1]: Reached target Suspend.
Mar 28 10:10:36 localhost systemd[1]: Started Daemon for power management.
Mar 28 10:11:32 dhcppc4 systemd[1]: Deactivating swap /dev/sda8...
Mar 28 10:11:32 dhcppc4 systemd[1]: Deactivating swap /dev/sda8...
Mar 28 10:11:32 dhcppc4 systemd[1]: Deactivating swap /dev/sda8...
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Sound Card.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopped target Sound Card.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Daemon for power management...
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Authorization Manager...
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Graphical Interface.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopped target Graphical Interface.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Multi-User.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopped target Multi-User.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping ACPI event daemon...
Mar 28 10:11:34 dhcppc4 systemd[1]: slim.service: main process exited, code=exited, status=1/FAILURE
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped SLiM Simple Login Manager.
Mar 28 10:11:34 dhcppc4 systemd[1]: Unit slim.service entered failed state
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Permit User Sessions...
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Permit User Sessions.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Basic System.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped target Basic System.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Dispatch Password Requests to Console Directory Watch.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Dispatch Password Requests to Console Directory Watch.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Forward Password Requests to Wall Directory Watch.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Forward Password Requests to Wall Directory Watch.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Daily Cleanup of Temporary Directories.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Daily Cleanup of Temporary Directories.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Sockets.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped target Sockets.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping LVM2 metadata daemon socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed LVM2 metadata daemon socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Device-mapper event daemon FIFOs.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed Device-mapper event daemon FIFOs.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Syslog Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed Syslog Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping ACPID Listen Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed ACPID Listen Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping D-Bus System Message Bus Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed D-Bus System Message Bus Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping System Initialization.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped target System Initialization.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Load Kernel Modules...
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Load Kernel Modules.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Apply Kernel Variables...
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Apply Kernel Variables.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Setup Virtual Console...
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped Setup Virtual Console.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Set Up Additional Binary Formats...
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped Set Up Additional Binary Formats.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Encrypted Volumes.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Encrypted Volumes.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Swap.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Swap.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Local File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Local File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Unmounting /home...
Mar 28 10:11:35 dhcppc4 systemd[1]: Unmounting /tmp...
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Remote File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Remote File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Unmounted /tmp.
Mar 28 10:11:35 dhcppc4 systemd[1]: Unmounted /home.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Unmount All Filesystems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Reached target Unmount All Filesystems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Local File Systems (Pre).
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Local File Systems (Pre).
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Remount Root and Kernel File Systems...
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped Remount Root and Kernel File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Shutdown.
Mar 28 10:11:35 dhcppc4 systemd[1]: Reached target Shutdown.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Save Random Seed...
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Update UTMP about System Shutdown...
Mar 28 10:11:35 dhcppc4 systemd[1]: Started Save Random Seed.
Mar 28 10:11:35 dhcppc4 systemd[1]: Started Update UTMP about System Shutdown.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Final Step.
Mar 28 10:11:35 dhcppc4 systemd[1]: Reached target Final Step.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Reboot...
Mar 28 10:11:35 dhcppc4 systemd[1]: Shutting down.
Mar 28 10:11:35 dhcppc4 systemd[1]: Hardware watchdog 'iTCO_wdt', version 0
Mar 28 10:11:35 dhcppc4 systemd[1]: Reached target Unmount All Filesystems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Local File Systems (Pre).
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Local File Systems (Pre).
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Remount Root and Kernel File Systems...
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped Remount Root and Kernel File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Shutdown.
Mar 28 10:11:35 dhcppc4 systemd[1]: Reached target Shutdown.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Save Random Seed...
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Update UTMP about System Shutdown...
Mar 28 10:11:35 dhcppc4 systemd[1]: Started Save Random Seed.
Mar 28 10:11:35 dhcppc4 systemd[1]: Started Update UTMP about System Shutdown.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Final Step.
Mar 28 10:11:35 dhcppc4 systemd[1]: Reached target Final Step.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Reboot...
Mar 28 10:11:35 dhcppc4 systemd[1]: Shutting down.
Mar 28 10:11:35 dhcppc4 systemd[1]: Hardware watchdog 'iTCO_wdt', version 0
Mar 28 10:11:35 dhcppc4 systemd[1]: Set hardware watchdog to 10min.
Last edited by xorgx3 (2013-03-28 10:52:08) -
Location Manager Strange Behavior
Hi,
debbung my application i have discovered that location manager have sometimes a strange behavior. Sometimes when i start to get location only the first "Bad" point with v. accur. = -1 is returned then no other point i returned. If then i open Apple Map i see that also map doesn't get point. So i must shutdown and restart Location service and all work perfectly. I have also strange issue when i change distanceFilter in the already created location manager Instance. it's doesn't work no point are peeked. If i restart the app sometimes work.
Finally i have discovered on the iphone syslog that it try to connect to an apple site "http://iphone-wu.apple.com" to download a file" lto2.dat" someone know what is this file?
Thanks youHello, I see the same in my Iphone.
I search in google and found this:
"Global Locate predicts the satellite orbits for 2, 4, 7, or 10
days in advance, and you download that. AKA "Long Term Orbit" or LTO."
It's a module used in opensource gps -
Strange behavior when "trying" to burn a disk.
At least I think this is strange behavior, following the instructions in the help viewer, topic "Backing up your music to a CD or DVD." One thing for sure, it's not burning a disc and it ain't telling me why.
I select the playlist and click "Burn Disc"
Requests a blank disc. I insert one.
Message "checking media"
after about a minute, the disc ejects
Message "checking media" displays another 30 seconds
No other messages displayed.
What the ??? Shouldn't it at least display an error message??
Super-Drive information..... from System Profiler
MATSHITA DVD-R UJ-845C:
Firmware Revision: DPP9
Interconnect: ATAPI
Burn Support: Yes (Apple Shipped/Supported)
Cache: 2048 KB
Reads DVD: Yes
CD-Write: -R, -RW
DVD-Write: -R, -RW, +R, +RW
Burn Underrun Protection CD: Yes
Burn Underrun Protection DVD: Yes
Write Strategies: CD-TAO, CD-SAO, DVD-DAO
Media: No
Using Sony DVD+R discs.
Mac Mini Mac OS X (10.4.8)Whoops, sorry, this was while burning a playlist.
I've also tried some Pleomax CD disks (Samsung), with no luck. I've tried burning directly from iTunes, and from Toast 7.
Of the types I've tried, the Sony DVD's have been the best for me. Haven't tried many types though. Maybe I can get disks one at a time until I find a brand my burner likes.
Still, isn't it strange that there is NO error message? It just quits?
Mac Mini Mac OS X (10.4.8) -
Strange Behavior with gMSA in Server 2012 R2
Greetings,
I have been doing some testing with gMSA Accounts in a Server 2012 R2 environment (two separate environments, actually), and I have noticed something very strange that occurred in both environments, which does not appear to be occurring in one of our customer's
self-managed environments.
We created a Group Managed Service Account using the following article:
http://blogs.technet.com/b/askpfeplat/archive/2012/12/17/windows-server-2012-group-managed-service-accounts.aspx
Everything went smoothly, and the account installs/tests successfully on both of the hosts that we are testing on. I am able to set my services to run under the account, and most of them appear to work fine. I am having some issues with a few of my services,
and I believe that the strange behavior I am seeing may have something to do with this - described below:
As soon as I set the service's Log On Account (via the Log On Tab under the Service's Properties), the entirety of the "Log On" tab changes to "greyed out," and I am unable to change the Log On account back via the GUI (Screenshot
attached).
I found that I am able to successfully change the account via Command Line using sc.exe, but the Log On tab remains greyed out! So far, I have found nothing to remedy this, but confirmed that it happens for any service I set to use the gMSA as the Logon
Account, and that it happens in 2 separate test environments, but not in a Customer's production environment - very strange.
All servers in this environment are running Server 2012 R2, and domain Functional Level is currently Server 2012.
I have been unable to find any information online about this behavior, so I am hoping someone has seen this before, and can explain why this is happening.
NickVIvian,
Yes, we used the Install-AdServiceAccount gMSA command on each host using the gMSA account, and then ran Test-AdServiceAccount gMSA, which returned "True."
However, one thing I noticed is that if I run Test-ADServiceAccount gMSA as a Local Administrator, it fails with the following:
PS C:\Users\Administrator> Test-AdServiceAccount gMSA$
Test-AdServiceAccount : The server has rejected the client credentials.
At line:1 char:1
+ Test-AdServiceAccount gMSA$
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : SecurityError: (:) [Test-ADServiceAccount], AuthenticationException
+ FullyQualifiedErrorId : ActiveDirectoryCmdlet:System.Security.Authentication.AuthenticationException,Microsoft.A
ctiveDirectory.Management.Commands.TestADServiceAccount
If I run Test-ADServiceAccount gMSA as Domain Administrator, it returns true:
PS C:\Users\Administrator.<domainname>> Test-AdServiceAccount gMSA$
True
Is this normal?
Overall, I think the issue I am running into is at the Application Level, and not a problem with the gMSA, as it appears to be working. (Can Start/Stop services without any issues). I will be investigating my issue further with 3rd-party vendors, unless
you think there is something wrong with my gMSA accounts based on the information I have provided.
Nick -
Strange Behavior from iTunes 7.2
Running itunes - 7.2Recently had my itunes library “corrupted” or non functional.
Spent a long, long time rebuilding the library (see below) and noticed some strange behavior that has me terrified that itunes is corrupted and I am going to loose all the hard work, etc..
1. I have about 100 GB of music in various formats (apple protected/itunes store, mp3 (128 to 320), apple lossless, wav) and when I tried to rebuild the library by clicking on add to library it only added about 65 GB of the 100 GB. I had to go through and figure out what was missing and manually choose the specific folder when I added it.
Major pain and very time consuming.
So it is not adding songs correctly, but through way too much effort able to work around this.
2. About ½ of the itunes store tunes I purchased are no longer apple protected format. Somehow they were converted to mp3 at 192kbs. Some of the songs play fine others are now not as crisp and make a poping sound or skip. How could this happen? Are these files corrupted? Will I loose them?
3. At the top center of itunes the information bar, where the read out is for what song is playing and how much time has elapsed in the song, is not working. When I click on a song it starts playing but the elapsed time bar and counter never move, and when the next song starts playing the information never changes. It is stuck on what ever song you initiate play with by clicking on it and the information stays frozen.
4. itunes randomly stops playing at the end of a song….If listening to an album it is usually after three or four songs and when listening to a play list it is usually after one song.
I am afraid itunes is corrupted and will not function correctly and I am going to loose the hard work I put in trying to recover from the last crash.
Any suggestions??
Can’t wait for time machine. I hope it works as advertised. If so I could just go back in time to the last time iTunes worked correctly and go from there.First of all I hope that you have a good b/u of all your tunes - either on ext HD or on DVD. Don't forget to b/u the iTunes Library and .xml files at the same time.
Have you tried to reinstall iTunes? Drag the app to the trash and remove the iTunesX.pkg from HD>Library>Receipts>iTunesX.pkg. Using a fresh .dmg of iTunes 7.2 reinstall.
Have you repaired permissions with Disk Utility?
Is your Quicktime up to date? At least version v7.1.5.
MJ -
Strange behavior - icon thumbnail instead of image - CC@OSX10.10
Hi,
my CC (@OS X 10.10.3) showing a strange behavior using vanishing point filter.
After defining grid and try to paste the image OS X paste the icon thumbnail instead of the image,
Many thanks in advance!!
br
JoachimIt is probably related to the fact that you are setting the tables row height in the renderer this will fire a render message when the height changes. One height is applied to all rows of a table. This means that is you have images of different heights you are continually changing the tables row height and therefore continually rendereing.
My approach would be to have all the images fit into a set size ( say 64*64 ( with scaling if neccesary ) you could then have a popup show the full size image if required. -
Strange behavior in report Output
Hi,
Strange behavior in report output , please some one help me out of this problem.
I am using Oracle order capture rdf file ASOPQTEL.rdf.
My working environment:
Windows,apps instance .Now this rdf file is working fine in my work Environment.
when this same file is deployed in client environment (UNIX and different apps instance from my working environment apps instance)
for some cases it is giving output.
for some cases it's throughing error.
Thanks,
MithunPlease specify what kind of error you are getting and what is command you are firing on Unix.
-
Strange behavior of the Macbook pro display
Hi to all
I'm using my MacBook pro, and notice some strange behavior after open several windows or applications, I don't know how to explain, so here is a photo:
http://www.flickr.com/photos/86155326@N00/
I have tried: go back to 10.4.6 / create a new account / Hardware test... and Nothing.
Any suggestions?
PedroI am having the exact same problem(and no one is replying to my post either), I read in another post of someone who had a somewhat similar issue and someone commented that it was bad VRAM and warranted the logic board to be replaced. I'm hoping this is not the case, or at least hoping the problem does not get worse because I am in school and can't be without this computer for 2 weeks while it gets repaired..I'm hoping I can last til the holidays...
pictures of my problem:
http://www.rpi.edu/~neala/pics/display/Messed%20up%20desktop.png
http://www.rpi.edu/~neala/pics/display/Picture%204.png
Sometimes I can make it go away by moving windows, and sometimes that makes it worse... this computer is only 100 days old...come on apple..help us out! -
Strange behavior when I try to match a mpeg2 video with the menu size image
hello all,
got a strange behavior when I try to match a mpeg2 video with the menu size image,
menu size is 1920 x 1080 (photoshop file)
mpeg2 video 1920 x 1080 (1second 19 frames)
the idea is to go from the menu link to the next sub menu with a video as transition, using the same image on the video as the menu and then zooming in (in my case through a door) to end up after the zoom in the next level menu.
I try to achieve a smooth change from the first play menu picture to the video image into the next level menu picture,
everything works good but when I watch it on the preview mode on the left and right side of the video it shows a black bar at least 15 to 25 pixel wide, that means the video image appears smaller and it causes a little jump what is preety disturbing and can not be sold as a professional work.
why encore treats the video size and picture differently?
it's gratful appreciated if somebody who got experience in a transition I mentioned obove posting any solution,
thankl you allHi all
I'm having a very similar problem with Encore. My menu items are distorting (a minor but infuriating squashing top and bottom) when previewed.
Using Encore,PS,AE CS4
DVD format SD PAL DV widescreen
I created 3 menu frameworks and 3 video transistions to link them in AE. On the final frame of each transistion in AE I saved the frame with Composition>Save Frame to> Photoshop Layers. In PS i added the button functionality and saved.
In Encore I use Dynamic link to import AE transistions as timelines and imported each PS menu twice, once as "menu" and once as an asset.
When I link the timeline transistions to the menu and preview at the point the menu begins the whole image is squashed. When the next transistion is activated the image returns to its original size.
Thinking it was the use of PS that was causing the menus to distort I used the menu asset directly in the time line. Obviously no menu functionality but also no distortion. The AE transistion flowed straight into the "menu" just as I expected.
In the properties panel the menu Aspect Ratio 16:9
The AE transistions PAR is SD PALwidescreen 1.4587.
I did try the Blu Ray suggestion above but the same distortion was apparent.
Any suggestions short of squashing the video to match the menu would be welcomed.
Thanks -
Strange behavior of textareas in BPEL Worklist (10.1.2)
I have a very strange behavior with linebreaks in all my <textarea>s in the BPEL-Worklist-jsps: (they work fine as <INPUT>s
Example:
Default-text:
line1
I update the textarea to:
line1
line2
-> hit update
line1
*** (second line is completly missing)
-> hitting update again (no change in text)
line2line1
*** (all on one line with the new line in front)
As Value I use:
<%=PayloadFormGenerator.selectNodeValue(payload, "/ns0:task/ns0:payload/ns1:abstract", form.getNamespaceMap(),"string", context.getLocale())%>
and as mentioned: It works fine for <INPUT>.
What do I do wrong? Is this a bug?
Daniel
Message was edited by:
user552073Had the same problem, could not get it to be consistent. I would say this is a bug, but decided to edit payloads via the database in the end...
Maybe you are looking for
-
Making it so visitors only see photos in detail view in iWeb?
Hey guys, is it possible to make it so when people click on a photo page they automatically see the photo browser at the top with the enlarged version of which ever photo is highlighted? Thanks!
-
When I log into my e-mails in windows mail I get a duplicate set of addresses resulting in double amounts of e-mails .. Any solutions please most welcome.. Echo69
-
I would like to change the alternate email address in my personal settings
Please help. Thank you.
-
Hello We have created a new table oin the CRM and the R/3 system. We would like to replicate the table entries from crm to R/3 via the middleware. We have done the following Created the table in the two systems Created a new Bdoc Generated the flow W
-
Photosmart c4640 scanner error
Scan Error. try scan from computer or see documentation. Tried several times, cannot fix this.