SFPs for DS-C9124

Hi,
We have DS-C9124-0-K9 MDS 9124 4Gbps FC switch without SFPs, we have old "Agilent“ SFP Transceivers which we tried to put on DS-C9124-0-K9 but it's not suported.
1. question is there a way to use Agilent SFP Transceivers Agilent SFP Transceivers on our Cisco DS-C9124-0-K9;
2. question if we have to use Cisco SFPs, is it neccesery for SFPs on EVA to be Cisco too?
BR

Hi,
1. You cannot use the Agilent SFP for your MDS 9124 4G FC switch. Here is a link on which SFP is supported on the MDS platform:
http://www.cisco.com/en/US/prod/collateral/ps4159/ps6409/ps4358/product_data_sheet09186a00801bc698.html
2. You don't have to use the Cisco SFPs on the HP EVA, since the EVA might not detect it. All you have to match is the wavelength and the fiber type. Let's say you are using MMF and DS-SFP-FC4G-SW SFP, your EVA's optic should be for MMF, FC 4Gbps and using 850nm wavelength.
HTH,
jerry

Similar Messages

  • Which SFP for MM 62.5 Fiber

    I am specking a SRW2008P-K9 switch for a customer.  They are using MM 62.5 fiber.  I need to know what Gig SFP will work for them.  I am also quoting them a WS-C3750X-24P-S.  I need the SFP for this also.

    Hi Scott, if you're looking for less than 550 meter, a multi mode SFP such as MGBSX1 will do the trick.
    If you're looking for info for the 3750, I'd recommend to post here
    https://supportforums.cisco.com/community/netpro/network-infrastructure/switching
    -Tom
    Please mark answered for helpful posts

  • 10Gb SFP for UTP?

    I need to build a new 3850 switch which requires some server to be connected to a few 10Gb ports which i need to buy the 3580-nm-4-10Gb module for the first time. Was tying to build up a BOM and finding the correct SFP to buy together with the module from this site
    http://www.cisco.com/c/en/us/products/collateral/interfaces-modules/transceiver-modules/data_sheet_c78-455693.html
    I didn't see any 10Gb SFP for copper, something similar to the GLC-T sfp for the 1Gb slot, the most relevant one would be the Twinax copper cable which comes with both ends of the sfp with the cable attached together. Now is this something that we buy to inter connect to server's 10Gb port? 
    Not too sure about the 10Gb SFP to connect to a server but if you guys and give me some of the example of the model that people would use that would be great!
    Cheers,
    Ben

    Hi Benny,
    That's interesting. I thinkg the Twinax active copper cable (with SFPs at both ends) is the way to go. But it depends on the interface on the other end - the server. The 10G server interfaces I've seen are normally having an SFP port, but... your have to check what the situation is at your end.
    In this case though, I guess the only factor to go for the copper cable would be the price. If you have SFPs at both ends of the connection, you can go optical. It's more robust and reliable, and it's cheeper these days.
    Regards,
    Boyan

  • 10Gig Copper SFP for Nexus F Series module (N7K-F248XP-25E)

    Does Cisco have 10Gig Copper SFP which can be supported on Nexus platform in the F Series module (N7K-F248XP-25E)

    Leo,
    Thank you for the answer, you mentioned 10Gig Copper module in your reply (Part# N7K-F248XT-25E) but I already have Fiber Module (Part# N7K-F248XP-25E), I just need 2 10Gig copper ports for my storage and cant afford to buy a whole new Copper module. My question was if there is any 10Gig Copper SFP supported on F Series Fiber Module (Part# N7K-F248XP-25E), (not a twinax/DAC cable since my distance is longer and Twinax wont work)

  • SFP for SGE2000P

    I am looking to connect a SGE2000P switch to an existing infrastructure. I am unable to locate any information in the literature specifying compatible SFP adaptors. I require to connect to MMF 1350nm 100BASE-FX?

    Hi David;
    Here is a link to the small business SFP, but note the frequency.
    Bad news is that the SGE2010 and not the SGE2000 supports the 100FX SFP (MFEFX1), check the quick start guide URL at the bottom of this post.
    http://www.cisco.com/en/US/prod/collateral/modules/ps9934/data_sheet_c78-552203.html
    Table 1. MFE and MGE SFP Transceiver Modules
    Description
    MFE Transceivers
    MFEBX1
    100BASE-BX-20U SFP transceiver for single-mode fiber, 1310 nm wavelength, support up to 20 km
    MFEFX1
    100BASE-FX SFP transceiver, for multimode fiber, 1310 nm wavelength, support up to 2 km
    MFELX1
    100BASE-LX SFP transceiver, for single-mode fiber, 1310 nm wavelength, support up to 10 km
    MGE Transceivers
    MGBBX1
    1000BASE-BX-20U SFP transceiver, for single-mode fiber, 1310 nm wavelength, support up to 40 km
    MGBLH1
    1000BASE-LH SFP transceiver, for single-mode fiber, 1310 nm wavelength, support up to 40 km
    MGBLX1
    1000BASE-LX SFP transceiver, for single-mode fiber, 1310 nm wavelength, support up to 10 km
    MGBSX1
    1000BASE-SX SFP transceiver, for multimode fiber, 850 nm wavelength, support up to 550 m
    MGBT1
    1000BASE-T SFP transceiver for category 5 copper wire, support up to 100 m
    NOTE:But according to the quick start guide the 100FX SFP is supported on the SGE2010 series but NOT the SGE2000 or SFE2000 series
    Here for your reference is the quick start guide;
    https://www.cisco.com/en/US/docs/interfaces_modules/csbna/mgb/quick_start/guide/Optical_Module_QSG_en-US.pdf
    regards Dave

  • SFP For ASR1006 -- Will GLC-LH-SM Work????

    I have an ASR1006 running IOS-XE 15.0 ADVENTERPRISE, so I would like to know if the SFP (which I got from another router) with part number GLC-LH-SM would work in it  -- it's for a Single Mode connection.  I ordered part number SFP-GE-L= already, but it has not arrived yet so I just want to know if GLC-LH-SM will work in the interim.

    Hi 
    I have an issue in my data center, could you please me help out.
    I have Cisco ASR1006 router in my data center and a 100Mpbs WAN link (over OFC) is coming from my ISP to my premises. The issue is my ISP is having 100BaseFx module at its end and I am having 1000BaseFx modules in my router. How should I terminate the OFC on my router as 100BaseFx are 1000BaseFx are incompatible ? Please recommend any SFP which I could use at my end in order to terminate the OFC directly on my router. I have an 8 port SPA on my ASR.

  • Sfp for Lan to lan Level 2

                       Hi,
    Sorry i dont speak english, so i tried to explain my problem
    ONLY FOR LAN TO LAN  L2 with vlan ...
    I want to interconnect my office with a datacenter (2400 meters). One black fiber exist (i dont know if it s a multimod or monomod now)
    In first i think to use  2 switchs 3750X with a sfp modul. With one fiber, i m compulsory to use BIDIRECTIONNAL SFP.
    A Gibabit is sufficient for me.
    Question  1   Is it a good solution and does SFT Exist for that on 3750X , if no other switch for that ?
    Question 2 what else solution exist for metroplitain network (adaptateur  Fiber-Cover before ??
    Thanks you for help
    Bests regards
    Christophe

    Q1. Bidirectional SFP (1000BASE-BX10-D and 1000BASE-BX10-U) is an acceptable solution for 1Gbps links with only one Singlemode (mono-mode) fiber available. Supports 10,000 meters over SMF.
    Gigabit Ethernet SFP compatibility with 3750X can be found on website.
    Q2. I do not understand what other information you are looking for. 

  • 10Gig SFP for 7 Meters

    Not sure if you take other vendors and then “ciscolize” it (ie HP or IBM to MCS Callmanager) but do anyone know if Cisco also ciscolize the SFP cables?
    I see 7meter cables available below via other vendors. All the vendors (including Cisco) uses the same Madison 24AWG cable. However, with the transceivers themselves, I couldn’t tell if they all come same vendor or not.
    http://www.tmcscsi.com/SFP+_cables.shtml
    Anyways, does anyone know why is the 7M available in other vendors but not via Cisco?
    Also, is the transceiver really Cisco or some other vendor

    To answer this question:
    "... does anyone know why is the 7M available in other vendors but not via Cisco?"
    As of right now Cisco is the only vendor supporting FCoE on SFP+ copper cables, and Cisco will not certify the 7m passive copper cable for FCoE.  With FCoE, there are bit error rate tolerances that the vendor must be mindful of, and the bit error rate on the 7m cable is not meeting Cisco's strict quality tolerances.
    Other vendors that are not currently supporting FCoE, such as HP, do not need to worry about this (yet).
    So, if you plan to run FCoE traffic on these cables anytime now or in the future, you might want to stick to 5m or less cables regardless of which vendor you choose, because any other vendor will likely come to the same conclusion as Cisco has already done with support for FCoE on 7m passive SFP copper cables.
    Cheers,
    Brad

  • GLC-LX-SM-RGD SFP for 15kms

    Hi Guys,
    My first post.
    I have a L2 network spanning 12km, 13km, 14km and 16km.
    Have purchased GLC-LX-SM-RGD and now I notice that the specs say 10km. I am commissioning next week and want to know will the SFP shoot that distance ? Will it help to set the speed on the interface to 10mbps to get the link working ?
    Thanks in advance and really appreciate your comments and feedback.
    - Alvin

    1000BASE-LX/LH
    -3 to -9.5
    -3 to -20
    2.4 (any MMF)
    6 (G.652 SMF)
    1270 to 1355
    Optical budget is not 16-17dBm but around 10-10.5dBm a realistic. Take the lowest value of Transmit level not highest. So should be fine and you can test but these transmit values can change over time.So if you are very close not worth to take chance.
    Hope the existing 10Km hop is using the same kind of SFP means working on 1300nm not 1500nm. 

  • CVR-X2-SFP= for 4948? Pretty Please?

    I love this module, its exactly what I needed. Problem is, I only see it for the 3750's, but all of us that bought the 4948's and want that function are stuck out in the cold. Any plans to make it compatible with the 4948?

    Any word on this, if you're still using this gear? Were you able to get 1gig LC fiber to work on your 4948? (perhaps you found another transceiver that worked instead?)

  • SFP SR 1Gbps for FPNM-4SX-1G-NBP

    Hi, I need additional SFP for FPNM-4SX-1G-NBP (FirePOWER 4-Port 1Gbps SX FI Network Module with Non-Bypass) card. I think SFP-F-1-SR was the part number in Sourcefire price list but I can't find it in Cisco price list.
    Any idea?

    Legacy Sourcefire Part Number
    Legacy Sourcefire Part Number Description
    Cisco HW/SW Part No.
    Cisco Product Part Description
    Cisco License Part Number
    Cisco License Part Number Description
    Cisco Support Part Number
    Cisco Support Part Number Description
    NM-FX4-FW-0
    4 Port Fiber SX 1Gbps Network Interface Module for 3D 8XXX (non-bypass)
    FPNM-4SX-1G-NBP=
    FirePOWER 4-Port 1Gbps SX FI Network Module with Non-Bypass
    CON-SNT-NM-4SX-NBP
    FirePOWER 4-Port 1Gbps SX FI Network Module with Non-Bypass
    SFP-F-1-SX
    SFP module, Fiber 1000Base-SX 850nm 550m transiever
    GLC-SX-MMD
    1000BASE-SX SFP transceiver module, MMF, 850nm, DOM
    Servive is no longer required. If product breaks, buy SPARE unit to replace it.

  • Visio Stencil for HWIC-1GE-SFP

                     Does anyone know if there is a visio stencil for the HWIC-1GE-SFP for a 2951 router?  I have looked through the index of stencils, but it is not listed there.  Any suggestions would be appreciated.  Thanks!
    Gil

    Hi Bruno,
    I have just emailed the product group to request funding for the following:
    EHWIC-4ESG
    EHWIC-4ESG-P
    EHWIC-D-8ESG
    EHWIC-D-8ESG-
    EHWIC-4SHDSL-EA
    EHWIC-1GE-SFP-CU
    Those are all of the EHWIC module part numbers that I could find. We are dependent upon the product groups to authorize and fund the Visio work and hopefully I will hear from them soon.
    Regards,
    Brett Newman
    Cisco Visio Production
    Visimation Inc.
    www.shapesource.com

  • Fields missing in Interactive forms in SFP

    Hi All,
    I am using interactive forms (transaction SFP) for Prsonnel change request in MSS.When i go to this form ISR_FORM_SPEG thru SFP, i realised that come standard fileds like PERNR,ENAME etc are missing ( Generic ISR Table Type) are missing from the context folder of ISR_FORM_SPEG.Any idea how i can bring them back into place??
    Regards,
    Aditi

    Hi Aditi,
    Go to transaction QISRSCENARIO. check if these fields are there in the characteristics of the corresponding scenario (here SPEG). If they are there, click on the change button next to the form name in the Basic data of the scenario. A pop up message asking you to change the context fields as per the characteristics fields. This gets you to the ALCDesigner. Once the proper bindings are done for the form, exit and lets you go back to the qisrscenario transaction. save the data and also activate the form. <provided you are viewing the standard scenario in the change mode>.
    else
    copy this scenario and make    the adjustments you need.
    if there are some fields in the form that are not part of the characteristics, click on the import form fields button next to the form name. and save it.
    Hope this will solve your problem.
    do update the forum reg your findings.
    Thanks and warm regards,
    Anto.

  • How to develop a single form for multiple Layouts in Adobe

    Hi experts,
    I have Developed an AdobeForm in Letter Layout.
    Is there any settings in ADS/Layout in SFP, for giving print in both Letter and A4 Pages without developing new Page Layout?
    We are facing allignment issues, if print is given in A4.
    Thanks in Advance!
    Roopesh

    Hi Roopesh,
    We cannot change the Page Layout and Orientation dynamically in Adobe forms.
    To achieve this Create two forms with different layouts each.

  • Node in Form to change IDES Logo to Company Logo in TCode: SFP

    Hi All,
    In TCode: SFP for form PTRV_EXPENSE_FORM  in the "Context" tab  I check the nodes "I_FORM_HEADER_DATA_EMPLPYEE", "I_FORM_HEADER_DATA_EMPLPYER"  and other nodes but they dosent have a subnode to change IDES logo. Unfortunately the "Layout" is not displaying by throwing up an error saying "design tools not present(i.e not installed)"
    I also searched with terms LOGO/Image/Graphics on the form in "Context" tab but nothing showed up in the search
    Could anyone please tell me the subnode where can I upload Company Logo
    Regards,
    Latha

    Hi Waz
    Thanks for your quick reply. I really appreciate your reply
    I dont have authorization to access SO10.
    I checked for INCLUDE ADRS_HEADER OBJECT TEXT ID ADRS in the form but couldnt find it.
    Could you please explain me in detail if possible.
    Regards,
    Latha

Maybe you are looking for