SG 200-26 led system parpadea intermitentemente

Amigos tengo un switch modelo SG 200-26 el cual como primer indicio comentar que el LED system parpadea intermitentemente. Luego esto enchufo un cable ethernet a un puerto X y éste parpadea como maximo 3 segundos en verde y luego se apaga completamente el led del puerto X.
Mencionar tambien que cuando enchufo y desenchufo, todos los leds encienden.
Gracias por su ayuda de antemano.
Dr.

Hola senor, el LED parpadeara cuando DHCP esta configurado dentro del switch y la IP address no es recibido por DHCP todavia. Cuando usted conecta un cable al LAN, es probable que el LAN tiene DHCP y por lo tanto el switch recibe una IP address. Entonces el LED sera constante. Si usted configura dentro del switch un IP address invariable, el LED tambien sera constante. Lo siento por mi espanol...todavia estoy aprendiendo.

Similar Messages

Wi-Fi LED system

I am doing a project on Wi-Fi LED system using program from labview and arduino. It involves using data dashboard from iPad to remotely control the LED via a wireless router. I want to add another function, that once the iPad is connected to the router, the LED will turn on. Pls help.

Hey,,s10114751 !!
After reading your entire stuff from the post I still have a question in my mind the can please elaborate what's the basic role of Arduino as if I'm a bit confused to answer your question and it would be great if you could tell me its role so that I could guide you perfectly.
Info

FLASHING LED SYSTEM

HI,
THANKS TO EVERYONE WHO REPLIED TO MY QUERRY. WELL LET ME GET MY PROJECT CLEAR. I HAVE A DAQ CARD AND USING LABVIEW I NEED TO DESIGN A SYSTEM WHICH WOULD CONTROL FLASHING OF LED'S. THESE ARE REAL LED'S WHICH WOULD BE PUT UP ON A SCREEN. EACH OF THESE LED'S MUST GLOW FOR A SPECIFIC TIME (A FEW MS(800-1000) AFTER WHICH THEY MUST TURN OFF AND THEN THE NEXT LED MUST GLOW. EACH ONE MUST GLOW RANDOMLY. I M RELATIVELY NEW TO LABVIEW AND LEARNING IT RIGHT NOW. I HAVE USED THE WAIT FUNCTION TO GENERATE THE DELAY BUT HOWEVER I END UP HAVING TWO CONTROLS AT A SINGLE DEVICE WHICH GENERATES AN ERROR. I UNDERSTAND THAT I MUST USE THE DAQ ASSISTANT FOR INTERFACING. HOWEVER HOW CAN I GENERATE APPROPRIATE DELAY TIMES. CAN SOMEONE GUIDE ME ON THE RIGHT TRACK SO THAT I CAN WORK ON THAT. THANKS AGAIN TO ALL WHO HAVE REPLIED EARLIER.
WAITING FOR REPLIES
THANKS
KUNAL

Besides Henrik's suggestion about de-activating the caps lock key, the standard protocol is that
you continue to reply to your original post and NOT start a new topic.
Anyway, I am understanding your request properly, I would set up some sort of random number
generation which would pick which LED would be one that is lit.
In a system using a DIO board, you would change the state of one output and leave the others
the same.
Attachments:
Leds.vi ‏11 KB

K8N Neo2 4 Red LEDs system boots fine except...Please Help

Just installed a K8N with new AMD Athlon 64 3000+ with factory heatsink and fan. Everything boots up fine except that I have 4 Red LEDs. I am using a 450W power supply...its a powerlab brand (didnt cost very much) but has high voltages, windows seems to be running fine. Programs run and install etc. So according to the LED guide the cpu is installed incorrectly...if that was true wouldn't it not run correctly. If I need to reinstall heatsink how do I go about that since there was a thermal coating on the heatsink already.
Additonally:
1. whenever I do an audio test the right channel plays out the left speaker and vice versa.
2. When I try to boot with a second HD it locks up during the splash screen. I messed around with jumpers and nothing seemed to work.
This is my first system build
Please Help

Let me answer the last, first. Yes you can get different RAM that will perform differently. However not all more Expensive RAM will be faster or more stable. I know some of that does not make the sense you would think but remember that the A64 likes cheapy RAM in a lot of cases better than Uber RAM.
OK back to timings. If you test Bandwidth with say SiSoft Sandra you will see that changing from 3,3,8 top say 4,4,8 will hardly affect the performance. Manybe more so it would affect you if you had the system cranked to max overclock. However even then if would not be anything you will notice say running a game or even in other benchmarks. We went through the same issues with the Via boards and I think you will be suprised with the results. In my case going from 4,3,8 to 4,4,8 dropped my Sandra results from 3031 to 3029. You can even determine that amount of difference and in fact that is within the margin of error for the test.
OK so I still say try it and see if the system runs better. Oh and back to the other question for a moment. When we compaired my cheapie RAM in the Via section to some nice Uber Expensive RAM we saw almost identical results ranginging from 3020-3050 at stock speeds. So unless you are planning to really overclock heavy you likely won't see any difference between $80 per 512MB stick and $150 512MB sticks.
Some food for thought. We tested, you decide.

Panasonic sc bt 200 Home theatre system & Panasonic tx-l37v10b

I have just purchased an Apple Tv to connect to my home theatre system and LCD TV.
I can get the picture through HDMI cable (port 4) but the sound is the virgin cable TV.
I can't get my head round the configuration and which cable needs to go where!
Anyone help or is it not possible to have all 3 working
Thanks James

Thanks Winston I have connected the Apple Tv to the HDMI on the TV port 4
Amy

My System wont start after setting FSB to 200

My System wont start after I'd set my FSB to 200,
when the system starts, nothing comes up, and my Pc screen LED just blinks,
I have tryed to reseting the Bios but it doesn't help, have also tryed with new RAM and new Graphiccard but it doesnt help.
Please help me:-(
Am I resetting the Bios wrong? I set the jumper to safe mode and 100mhz, then I use the jumper to clear the CMOS. And the restart at set the jumpers back
3ghz AMD BARTON
NVIDIA nforce2 k7bn2 Delta
512 DDR RAM PCI3200
300WATT

Quote
Originally posted by roobster
set the multiplier lower , FSB(200) X multiplier (ex.10.5) = 2100 MHz , and your voltage raise it a bit too let say 1,700 ( default is 1.650 ) If this doesn't work at once , keep booting . My rig started up after 5 times . Strange but true .
does not work if he has a 3000.
they are multiplier locked.

NSS6000 red system led on reboot

Hi, i have my NSS6000 with the newest firmware version: NSS6000 Firmware v1.21.0
When i reboot it, i always have the red led system error. Its not this error solved yet????
I have the boot stick in order to reboot the NAS ok, but i thought this wasnt needed anymore....

Hi. These products are being handled by the Cisco Small Business Support Community. (URL: https://supportforums.cisco.com/community/netpro/small-business )

How do you convert Logical System Names of BW systems in BO

Hi,
We have implemented SSO where user/role administration takes place in BW, and then imported into BO where authorization to folders and reports are maintained.
What we are NOT yet able to figure out is how to move our BO groups (i.e. those groups that were automatically created from BW roles) and have them automatically mapped to the roles in the next environment.
Below is the scenario:
BW Dev Environment
System XXD
Client   100
Role     ZHR
BO Dev Environment
BW role ZHR has been imported and group XXD100@ZHR is automatically created. Also, we have granted group XXD100@ZHR access to different folders, reports and universes in this environment.
BW Test Environment
System XXT
Client   200
Role     ZHR has been transported from Dev
BO Test Environment
We are not quite sure how to import XXD100@ZHR from our BO dev enviroment and have the group automatically changed to XXF200@ZHR with the access to the different folders, reports and universes retained. Your help is highly appreciated.
Regards,
Olu

Hi,
We are not quite sure how to import XXD100@ZHR from our BO dev enviroment and have the group automatically changed to XXF200@ZHR with the access to the different folders, reports and universes retained
>>>you actually do NOT want to have those roles imported because the role from you first system doesn't exist in the second system.
You first system is pointing to system XXD with Client 100 and the second system is pointing to system XXF and client 200 - very different systems.
the roles have to be imported as part of the overall SAP authentication configuration. In case this is about having a possible identical folder and security structure I would suggest you use also groups in the BusinessObjects system - standard BusinessObjects groups - use those to assign security and then assign the SAP groups as subgroups. In that way you keep the security configuration and only assign the right subgroups.
ingo

Change in FG/SFG valuation system from STD cost MAP

As of now we use Std cost for valuation of FG/SFG and we would like to switchover to MAP for following reasons:
1.We donu2019t see any significant benefit from present costing system. Std costing updation, monthly CO closing, periodical revision of STD cost is not really justifying any benefits compared to the overall efforts put in for above activities.
2.KE 30 reports fail to give correct productwise contribution status as system loads all variance to quantity sold during the PERIOD( e.g If production is 1000 qty, sales 200 qty- , then system will load the variance of entire 1000 qty to sales qty of 200). This is misleading. It is not possible to sale all produced qty in same period in our case.
3.SFGs being produced in one plant trfd to another for FG production. To produce final product X, SFG A is needed, to produce A, SFG B required, to produce B, SFG C required. This is discrete mfg process and and SFG are produced in different plants under same co code. So, we are not able get contribution report of product X as component SFG A it self contains OH/activity cost.( We want to calculate contribution company as a whole i.e Selling price minus material cost( actually bought out materials and not SFG).
We donu2019t want to go for material ledger, considering the manufacturing complexity. Now, we want to change price control of all FG/SFGs fromu201DSu201D to u201CVu201D on cut-off date after making stock NIL
Kindly give us your expert advise on this approach. What are the challenges we will face by doing so.? Is there any company done this type of changes?
MBS

Hi MBS
1. ML is the right and only solution for your expectations
2. Whether you adopt V or S - CO CLosing is what you cant avoid... You will still need to do the whole CO cycle whether you have V or S
3. Having price control V for In House Mfd materials will damage the inventory valuation forever... Refer Note 81682 - Pr.contr.V for semi-finished and finished, which explains this in detail
What you want is Actual Costing, which can only be delivered by ML
What you want to avoid is monthly CO Closing - Which you really cant avoid
If you still go with V - May be in future you would realise that S was better as suggested by SAP in the above note...
You can take up an enhancement with your ABAP team to develop the kind of reports you want... however, thats not going to be easy... Its gonna take very long to stabilize, even if achieved
br, Ajay M

System crash attempting to use the packet filtering on Solaris 10, MU7

I have been attempting to port my kernel module to run on Solaris 10, MU7 (from MU6). Some changes to the packet filtering hooks interface requires me to make code changes and linker option changes i.e -Nmisc/neti -Nmisc/hook
I now have my module loading successfully and "hooking" packets. However, I am seeing instability and after processing in the order of 100-200 packets the system crashes. See stack dump beow for details.
Also note that initially my callback hook function is very simple i.e returns 0.
I require assistance on identifying the root cause. The key code fragements are as follows:
int _init()
// allocated a control block using net_instance_alloc
// populated the nin_name, nin_create, nin_destroy, and nin_shutdown fields with valid callback functions
// registered the control block using net_instance_register
static int _attach(dip, cmd)
dev_info_t *dip;
ddi_attach_cmd_t cmd;
// initialised a hook control block using HOOK_INIT
// performed a protocol lookup (using net_protocol_lookup) on the net_id provided by the nin_create function callback
// registered the hook with the net_id protocol using net_hook_register
static int
myipf_hook4_in (hook_event_token_t tok, hook_data_t info, void *arg) {
// simple callback function for test purposes
return 0;
System Stack trace:
Boot device: /virtual-devices@100/channel-devices@200/disk@0:a File and args:
SunOS Release 5.10 Version Generic_139555-08 64-bit
Copyright 1983-2009 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
Hostname: bfs-t5440-03-ldm12
NIS domain name is bfs.nis
Reading ZFS config: done.
bfs-t5440-03-ldm12 console login:
panic[cpu9]/thread=2a100a67ca0: BAD TRAP: type=9 rp=2a100a67630 addr=7b6e8d48 mmu_fsr=0
sched: trap type = 0x9
addr=0x7b6e8d48
pid=0, pc=0x7b6e8d48, sp=0x2a100a66ed1, tstate=0x1606, context=0x0
g1-g7: 1910, 18b0, 2a100a678f0, 60010776b14, 1910, 0, 2a100a67ca0
000002a100a67350 unix:die+9c (9, 2a100a67630, 7b6e8d48, 0, 2a100a67410, 182b400)
%l0-3: 000000000100954c 0000000000000009 0000060020ac1620 00000000010523ac
%l4-7: 00000000018a3c78 0000060020ac1848 000003000481dbe0 00000000010ac400
000002a100a67430 unix:trap+6cc (2a100a67630, 10000, 0, 0, 30004028000, 2a100a67ca0)
%l0-3: 0000000000000000 000000000185b480 0000000000000009 0000000000000000
%l4-7: 0000000000000000 0000000000000000 0000000000001606 0000000000010200
000002a100a67580 unix:ktl0+64 (300014c8e40, 2a100a67890, 600114fb428, 3, 1, 0)
%l0-3: 0000030004028000 0000000000000048 0000000000001606 0000000001021604
%l4-7: 00000000003c0000 0000000000000001 0000000000000000 000002a100a67630
000002a100a676d0 hook:hook_run+7c (30001b039c0, 300014c8e40, 2a100a67890, 60012566ea8, 7b6e8d48, 1)
%l0-3: 0000030001b039c8 00000600117df3c0 0000000001878888 0000000000000000
%l4-7: 0000000000000000 000000000000003c 0000000000000000 0000000000000000
000002a100a67780 ip:ip_input+3b4 (0, 600135ca040, 0, 6001359bc28, 0, 0)
%l0-3: 0000000000000000 0000000000000000 0000000000000000 0000060011562000
%l4-7: 00000000e0000000 0000000000000001 0000000000000000 0000000000000000
000002a100a67910 dls:soft_ring_drain+78 (600135d1f00, 60011dfa940, 2, 2000000, 2, 0)
%l0-3: 0000000000000000 0000000000000000 0000000000000004 0000000000000005
%l4-7: 000006001359bc28 00000600135ca040 000000007be1c238 000000000000fffe
000002a100a679c0 dls:soft_ring_worker+64 (600135d1f00, 0, 2, 600135d1f4c, 0, 2a100a67a8a)
%l0-3: 000002a100a67a88 0000000000000000 000002a10001fca0 000002a10001fca0
%l4-7: 0000000000000002 0000000000000000 0000000000000002 00000000018f1000
syncing file systems... [1] 104 [1] 95 [1] 4 [1] 4 [1] 4 [1] 4 [1] 4 [1] 4 [1] 4 [1] 4 [1] 4 [1] 4 [1] 4 [1] 4 [1] 4 [1] 4 [1] 4 [1] 4 [1] 4 [1] 4 [1] 4 [1] 4 [1] 4 done (not all i/o completed)
dumping to /dev/dsk/c0d0s1, offset 644284416, content: kernel
100% done: 118970 pages dumped, compression ratio 10.00, dump succeeded
rebooting...
Resetting...
-eugene
Edited by: emonagh on Aug 25, 2009 1:54 AM
Edited by: emonagh on Aug 25, 2009 1:56 AM

I have checked weblogic download link.
Currently webloigc is only available only for below mentioned platforms:-
1. Windows (32 bit jvm)
2. Linux (32 bit jvm)
3. sun solaris (only SPARC) (32 bit JVM)
There is no generic installer available for weblogic 9.2
Thus what I want is weblogic 9.2 setup for x86 machine.
I have tried to run weblogic 9.2 setup for linux on sun solaris x86.
But it did not run, it also gave error message that some package is missing in /lib/.. folder.....

Copy Distribution model from non changeable client to new system

Hi EDI-Experts,
Help me.
How can I easily copy a distribution model from a nn-changeable client to w new system.
Example: DEV client 110, Test client 150 (with valid distribution model), new syste, QAE,cleint 200
How can I transport the distribution model from client 150 of DEV system to 200 of QAE system.
How does the generation of the partner profiles work then?Anything to consider?
!! Client 150 of DEV is not changeable !!
Many thanks
JW

Goto Transaction BD64.
In the Menubar Edit -->Model View --> Distribute
Transport
U have the option of distributing ur Model view to another client.
Hope this helps.
Regards,
Mithun
Edited by: Mithun Shetty on Jul 16, 2008 8:33 PM

CHARM Configuration Error - No Consolidation System

Hi
Im facing following errors in solution manager's CHARM.
No consolidation system found for SSD-150 (project ZCHARM_GIL)
No track for project ZCHARM_GIL with log. system SSD/150
i have more queries.
1.solar_project_admin > system Landscape> systems i have following config
Logical Component : SAP SOLUTION MANAGER
Product: SAP SOLUTION MANAGER [Solution Manager ABAP Stack]
Product Version : SAP SOLUTION MANAGER 7.0
DEvelopment SYstem : SSD: 150 ( SSD is my solution manager SID)
QAS : Blank
PRD : Blank
Do i need to maintain values GSD , GSQ , GSP (satelite system DEV, PRD, GSP)
2. in my satelite system DOMAIN_GSD transport route
System GSD - GSQ Transport Group - System GSQ
             /GSQTRG
System GSD : Transport Stratergy - Mass Transport Checked
          Transport Layer - ZGSD
target group: /GSQTRGRP/ GSQ 200
                GSQ 300
System GSD : Transport Stratergy - Mass Transport Checked
          Transport Layer - NONE
Transport Route : GSD - ZGSD/SAP - /GSQTRG - 300/200- GSQ
Can i configure charm with above scenarion where transport groups have been defined

Hi
This error occurs if you dont define the client dependent tms route in satellite system.
First visit this blog
First steps to work with Change Request Management scenario in SAP Solution Manager 7.0
then in spro change request management general settings....visit the img help for TMS settings of
further
TMS
TMS Setup
http://help.sap.com/saphelp_nw04/helpdata/en/14/c795388d62e450e10000009b38f889/frameset.htm
more help
http://wiki.sdn.sap.com/wiki/display/SM/ChangeRequestManagement
Regards
Prakhar

No system in the system landscape exports transport requests

Hi gurus,
We are trying to implement the Change Request Management scenario in
Solution Manager 4.0 SP12 in a POC.
The TMS are created with Solution Manager as Controller and with the settings are correct.
We have created a Maintenance Project with the following landscape :
system1 - Client 100 as Development System - Type of Rol "Source System"
system2 - Client 200 as Quality System - Type of Rol "Target System"
system2 - Client 100 as Production System - Type of Rol "Production System"
In the Change Request tab, when we check "Activate Change Request Management" checkbox, the following error is shown:
"System system2-100 is to be changed in a Solution Manager project, but no
system in the system landscape exports transport requests which are
imported into this system."
What is happening? Any idea??
Thanks

The reason may be, that your "POC" is not valid due to the fact, that you use "clients" and not "systems" to transport
What you can try to verify that is - take out the QA client/system out of the transport route and try then to activate just with DEV --> PRD.
We wanted to setup something similar in the past and TMS failed to get configured properly - due to exact that reason.
Markus

Jaybird JB 200 Bluetooth headset connects but no audio

Hi,
I have T400 with Windows 7 64 bit. I've installed the latest Bluetooth drivers. I can pair the Jaybird JB 200 headset, the system says it's connected, but I don't get any audio. The headset is silent and no controls work.
What am I missing to get this to work?
Thanks

hey mpjb,
it is really hard to say on what is missing, but could you try the following,
1. uninstall the bluetooth stack
2. add new hardware(bluetooth) and let the Win7 install it's generic bluetooth stack,
see if this works.
also does the Jaybird work on a different machine ?
WW Social Media
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
Have you checked out the Community Knowledgebase yet?!
How to send a private message? --> Check out this article.

NEO Boards Unofficial FAQ rev 4/05/2004 - two lights on "P" series

Hi all,
I'll start maintaining this Unofficial FAQ for the NEO boards. The contents of this FAQ are compiled from this forum, user's posted problems, usage issues, compatibility issues reported on the net etc. However, MSI does not responsible for the validity of this FAQ. Please take note.
1. BIOS
Q: I flashed the BIOS and caused my motherboard dead. Can I RMA the board?
A: This does not happen easily. Please be sure you follow the BIOS flashing instruction and wait for the BIOS flashing process to be fully completed before you restart the PC.
If this problem is caused by the recent bios 1.3 for the Intel875 ( MS6758 ) chipset, then he could ask for RMA from MSI Branch offices for Free.
If not caused by the 1.3 BIOS, they can still go through the normal RMA process. Please check with MSI branches.
Q: What is the MSI statement for the bad BIOS flash?
YES. This is the statement :Quote
When you update the bios to v1.4 using the latest flash utility, it will show "Erasing Done and then Programming Done". But actually the process has not been finished yet, you will need to wait about 30 seconds and then the message of "Flash Complete..." is showing up, this will complete the flash process.
By doing this, end user will assume when it display "Programming Done" message, it has complete the flash process which is wrong. We need to wait until the "Flash Complete..." message has displayed on the screen in order for completing the flash process.
By any chance we can remove the message of "Programming Done" and only prompt for "Flash Complete..." so customer will not turn off the system or reboot the system when they see "Programming Done" message pop on the screen?
The new version ADSFI708.EXE has fixed this issue. When you finish the BIOS , it will show the "Verifying the ROM data now" message before it showed up the "Flash Complete".
In short, use ADSFI708.EXE to flash the BIOS.
[/color]
Q: Where can I get beta BIOS?
MSI do not support beta BIOS. Use at your own risk. Under special condition such as hardware incompatibility issues and a beta BIOS is a feasible resolution, please post in the forum and let the mods arrange for you.
Latest BIOS:
Released:
875P Neo : 1.9
865PE Neo2 : 1.9
865PE Neo2-PS : 3.3 New![/B]
beta BIOS:
875P Neo : 1.9B6 link1 [Thanks to FlyTSI for hosting]
History: NO INFO PROVIDED FOR 1.9B6
865PE Neo2 : 2.01B link [thanks to FlyTSI]
History:Support Extreme OSB logo. Display L3 cache. Support Prescott cpu & update microcode. Modify Prescott ratio programming.
DO NOT APPROACH THE MODS FOR BETA BIOS! WE DO NOT DISTRIBUTE BETA BIOS!!
Q: What is the best BIOS setting for my board?
A: The optimal BIOS setting is different for each system. It's recommended to read more about the BIOS settings, from the board's manual, and some good guides like this : link.
2. Overclocking
Q:I cannot overclock my system. Can MSI update the BIOS so I can overclock?
A: This board can overclock, but overclocking depends on the peripherals that you are using like memory, CPU, heatsink etc.
Q: Which board has Dynamic Overclocking Technology?
A: Currently only 865PE Neo2-FIS2R
Q: How to disable dynamic overclocking?
A:Yes, you can disable Dynamic clocking directly in the bios setup.
3. CoreCell Technology
Q: which product has CoreCell technology built-in?
A: 875P Neo (MS-6758), 865GE Neo2 (MS-6728) & 865PE Neo2 (MS-6728)
Q: Can I assume that boards with CoreCell chip to have D.O.T ?
NO
Q: Where are the locations of temperature sensors?
CPU - taken directly from CPU pin (same as AMD thermal pin.
System - RT2 (near winbond I/O) same for 875/865 series boards.
4. RAM
Q: I have this RAM xxxx but it does not work with my board. Can MSI update the BIOS to fix this?
A: We would suggest you to use the MSI recommended memory for this part as there are a lot of memory brands out there we can't guarantee that all will work with the MB. Please go to the Product Info page, click "Test Report" and choose "Memory Modules".
For example, 875P : Here and select Memory Modules.
Q: My RAM performance is slow, the benchmark software such as PC Mark, Sisoft etc results are below par compared to other brands. WHY?
A: This issue has been identified. New BIOS update has fixed this problem. Please update to the latest BIOS.
Q: Is there any workaround?
A: There are users here share valueable information of how they tweak their BIOS to achieve good results. Kudos to them! :D Take a look at this link.
Q: What is MAT?
Memory Acceleration Technology. More to read here! Please read all to get the whole idea. You should have the idea what actually it is. :D
Q: Why my Neo2-S/LS doesn't have MAT?!
GOOD NEWS!! After first week of July, the new BIOS release will enable MAT in all Neo2 boards!
Q: What about DOT?
OK. Here is the answer:
Additional Info for MAT support:
MS-6728 BIOS V1.3 (All 865PE will support)
(Note: No MAT option for 865G due to limitation) Though the 865G have no support for MAT but if you insert AGP VGA card, you could still avail of this function!!
DOT support:
MS-6728, for exist boards, only full version supports it
Q: I want to have both MAT and DOT, can I do that?
Of course you can. However, the amount of setting you can used would depend on your current configurations. The suggested stable configuration if MAT as Fast & DOT as Captain
Q: Then what is PAT?
This is what I found in the forum, written by Assaf.
Quote
Here's what I understand about PAT.
As you may or may not know adding pipline stages to any execution unit will allow you to run it at a higher frequency but it will increase the latancy from start to end (measured in clock pulses).
Now, in order to ensure reliable operation at 800MHz FSB intel added 2 pipline stages to the memory controller (as based on the original dual memory controller in the E7205 chipset)
This they called i865PE and it will only put into action these 2 stages when 800MHz FSB is applied (which it needs the bios to tell it is the case)
Intel take the better yealdes of 865PE and validate them for 800MHz with the 2 extra stages disabled.
These they call 875P.
A 875P bios with PAT enabled simply does not "tell" the chipset it it running at 800MHz so the extra stages are inactive thus reducing latancy relative to a situation where these stages were activated.
A hacked 865PE bios will simply follow the 875P bios rule of not notifing the chipset it is running at 800MHz.
PAT is not an optimization, it's a de-un-optimization
[/color]
Q: Can 875P/865PE boards support DDR266 RAM for 800MHz FSB CPU?
Yes, although the product webpage did not highlight DDR266.
Q: My Kingston HyperX RAM always cause errors with 875/865 board!
Known issue. Please read here: http://www.kingston.com/support/faqs/memory/intel_3.asp
Q: My system does not run stably with DDR400
A: Set DDR Voltage to 2.7V and above for DDR400, regardless what the RAM manufacturer advertised.
Q: How to set different FSB:DDR ratio? I can't find in the BIOS
The FSB:DDR ratio can be changed by setting DDR Clock [266,333,400,500,533]. However, your processor's default FSB will affect the ratio. Follow this table:
FSB DDR ratio
133 266 1:1
133 333 4:5
133 400 2:3
133 466 -
133 500 -
133 533 -
200 266 3:2
200 333 5:4
200 400 1:1
200 466 -
200 500 4:5
200 533 3:4
If you have 800FSB (200Mhz) CPU, use FSB200 table. If you have 533FSB (133MHz) CPU, use FSB133 table to get the ratio. Ratio "-" is not available and out of chipset limit.
Examples:
1. DDR400 overclock P4 2.4GHz to 3.0GHz. Ratio 5:4. FSB:250MHz. DDR Clock : 333MHz
2. DDR333 overclock P4 2.4GHz to 3.0GHz. Ratio 3:2. FSB:250MHz. DDR Clock : 266MHz
3. DDR500 Pr default. Ratio 4:5. FSB:200MHz. DDR Clock: 500MHz.
5. HDDs
Q: Can Promise RAID support 2 PATA + 2 SATA = total of 4 HDDs for a single RAID array? RAID-0? RAID-1? RAID-0+1?
Yes, Promise RAID support 2 PATA + 2 SATA (RAID-0 or RAID-1 or RAID-0+1)
Q: Does ICH5R's SATA controller support RAID?
Yes, but only ICH5R, not ICH5. Update: MSI has released beta BIOS 1.81B with ICH5R RAID-1 support. Check the link above in the BIOS section.
Q: My HDD LED doesn't lit!!!
As what I have been told that the HDD LED only lit when there are activities in IDE Primary and Secondary channels. No support for ICH5's SATA and/or Promise SATA activities yet. In other words, the HDD LED will not lit and indicate any activities for your SATA drives.
Q: What is SATA? What is PATA?
SATA = Serial ATA. There was no such "PATA" acronym before. After Serial ATA appeared, people started to find IDE as opposing to Serial ATA, and hence called IDE as "Parallel ATA" or PATA.
Q: I enable SATA in BIOS but I didn't see any SATA Controller listed in the Device Manager!
You will see two sets of IDE ATA/ATAPI Controllers - Intel 82801EB Ultra ATA Controller x2, Primary IDE Channel x2, Secondary IDE Channel x2. That's how Windows installed the drivers.
Q: How should I install my HDD for RAID configuration?
Note that the Promise RAID controller only controls IDE-3, SER-3 and SER-4 ports. Make sure you have your HDDs connected to these ports. Make sure you have enabled "Onboard Promise IDE" in the BIOS. Then after the POST screen, press CTRL-F once prompted and go to the RAID setup screen to setup your RAID configuration.
While the ICH5R controls IDE-1, IDE-2, SER-1 and SER-2. For ICH5R, only SER-1 and SER-2 can be set as RAID. So make sure your SATA HDDs are connected to SER-1 and SER-2. But make sure you have enabled "Configure SATA as RAID" in the BIOS. After the POST screen, press CTRL-I once prompted and go to the ICH5R RAID setup screen to setup your RAID configuration.
For more comprehensive RAID setup guide, please read this guide written by vango44. Great contribution!!
Q: My SATA HDD always gives me errors, data corruptions and can't boot!!
Check the SATA HDD's bridge chip with a "M" logo, the chip build has to be B5P and above, not B2P/B3P which are known to be buggy. B4P is OK but B5P is better. Maxtor and Western Digital SATA HDDs are known to use this bridge chip. Seagate Barracuda V uses different bridge chip and does not make that much problems compared to Maxtor's. RMA the HDDs if possible. MSI is working on the BIOS to fix this incompatible issues. Get BIOS 1.9B3 or 1.6B2 or above. I have seen around October 2003 that Western Digital HDDs come with B5P bridge chip.
Q: I want to use IDE3 for normal HDD, non-RAID
Set this in the BIOS under Integrated Peripherals:
Onboard Promise IDE : As SATA
Q: What is Legacy mode and what is Native mode?
Legacy mode uses 14 and 15 IRQs. Legacy mode can support up to 2 IDE channels, each IRQ for each channel, which means it can support 2 SATA, or 2 SATA + 2 PATA or 4 PATA. Legacy mode also works comfortably with most OSes including Linux.
Native mode means you may use all available IRQs and can support up to 2 SATA and 4 PATA. Native mode may have issues working with some OSes such as Win9x and Linux, especially on IRQ assignments.If you have Win98/ME, use Legacy mode only!
Q: How to enable both SATA and PATA?
You can use both Legacy mode and Native mode, depending on how many devices you use as described above.
For Legacy Mode:
ATA Configuration: PATA+SATA
S-ATA Keep Enabled: Yes
P-ATA Keep Enabled: Yes
PATA Channel Selection: Both
Combined Mode Operation: PATA First/SATA First, depending on which you want to act as 1st Channel.
S-ATA Ports Definition: P0-1st/P1-2nd or P0-3rd/P1-4th, depending on which you want to act as Master.
For Native Mode:
ATA Configuration: SATA Only or PATA only, depending on which you want to be the FIRST BOOT device!
S-ATA Keep Enabled: Yes if you chose PATA only
P-ATA Keep Enabled: Yes if you chose SATA Only
PATA Channel Selection: Both
Combined Mode Operation: PATA First/SATA First, depending on which you want to act as 1st Channel.
S-ATA Ports Definition: - P0-1st/P1-2nd or P0-3rd/P1-4th, depending on which you want to act as Master.
Q: What is S-ATA Ports Definition?
There are two options: P0-1st/P1-2nd and P0-3rd/P1-4th. If you choose P0-1st/P1-2nd, your Port-0 S-ATA (SER-1) will become the 1st IDE Master, ie IDE-1 Master. and Port-1 S-ATA (SER-2) will become 2nd IDE Master. If you plan to boot with SATA HDD, it's recommended to set to P0-1st/P1-2nd. If you plan to boot with PATA HDD, it's recommended to set to P0-3rd/P1-4th.
Q: When I enable SATA+PATA mode, why only IDE-1 or IDE-2 can be used?
If you chose "SATA 1st Channel", IDE-1 will be dropped. If you chose "PATA 1st Channel", IDE-2 will be dropped.
Q: I want my SATA to be the 1st IDE drive in Legacy Mode along with PATA, how?
Set this:
ATA Configuration: PATA+SATA
S-ATA Keep Enabled: don't care
P-ATA Keep Enabled: don't care
PATA Channel Selection: don't care
Combined Mode Operation: SATA 1st Channel
S-ATA Ports Definition: P0-1st/P1-2nd
With this configuration, you can have your SER-1 and SER-2 act as IDE-1 master and slave. But you can only connect your PATA drives on IDE-2 slot.
Q: I am a noob, I want more details.
More info? here
Q: How to support 250GB HDD? Windows only sees up to 134GB.
Follow this instruction: here for Win2000 and WinXP.
Q: I've installed a new SATA HDD, I can find it in Device Manager but it doesn't appear in Windows Explorer at all! HELP!!
You need to format the HDD, not just SATA but also PATA HDD then only Windows Explorer can see it and assign it with a drive letter. To format a HDD, right click on My Computer, select Manage, look for Disk Management. You should see a no-drive-letter unformatted drive there in the list. Get it formatted by right click on it and choose the obvious option there is.
6. Onboard Sound
Q: My onboard sound lost after I overclock the system!
Goto BIOS setup and lock AGP/PCI to 67/33.
7. Universal Serial Bus [Thanks to Danny for contribution]
Q: Why doesn't my board have USB2 ports?
A: The ICH5 and ICH5R chipsets support up to 8 USB2 ports. Under Windows XP when you view your USB settings using Device Manager you will see 4 Intel 82801EB USB Universal Host Controllers and 1 Intel 82801EB USB2 Enhanced Host Controller; Windows 2000 is similar, you are looking for "Enhanced". If you don't see "Enhanced" you need to install SP1 for XP or the latest service pack for W2K. If you have these service packs installed and still don't see enhanced, used the Device Manager to remove the 5 controllers and reboot to allow Windows to correctly install the right drivers.
Q: If I have 8 USB2 ports, why does Sandra tell me they are USB1.1?
A: When lower speed devices are plugged in, or high speed devices are plugged in without USB2 operating system support, they are routed to the low speed host controllers. High speed devices are routed directly to the Enhanced host controller when operating system support exists.
Base on http://www.intel.com/design/chipsets/manuals/29865602.pdf
8. CPU - contributed by Danny! :biggthumbsup:
Q: I have an 800 FSB Pentium 4 CPU, but the bios is set for 200! If I set it to 800 it crashes! What is wrong?
A: The FSB rating of the CPU is 4 times the FSB rating of the motherboard. To quote Intel: "This is accomplished through a physical signaling scheme of quad pumping the data transfers over a 200 MHz clocked system bus and a buffering scheme allowing for sustained 800 MHz data transfers." So valid settings are 100 for a 400FSB CPU, 133 for a 533FSB CPU and 200 for an 800FSB CPU.
Q: The Windows task manager and the Device Manager show I have two CPU's. What's wrong?
A: Your CPU is a model that has Hyperthreading technology and it is enabled in the bios. To quote Intel: "It allows software programs to "see" two processors and work more efficiently. This new technology enables the processor to execute two series, or threads, of instructions at the same time, thereby improving performance and system responsiveness."
Q: Do these boards support Prescott CPU?
Update: Prescott spec is not finalized. There might be more requirements needed other than meeting FMB guideline. It is hard to say if current motherboards can fully support it. [/color]
This is the latest info from MSI. Check this link here
9. Power Management
Q: What are S1/POS and S3/STR modes?
S1/POS = Power On Suspend, nothing turn off just that everything is running in extremely slow.
S3/STR = Suspend to RAM, PSU only powers 5V_STBY to the board for RAM refreshing, the rest all off.
Additionally,
S4 = Suspend to Disk. Win2k/XP calls it "Hibernation" mode. In this mode, the RAM and CPU state images are copied into the HDD. After S4 mode, you can safely remove the power cord.
S5 = Soft Off. PSU still supplies 5V_STBY.
G3 = mechanical off. No power at all to the board.
Q: Where to set the standby modes?
For S1 and S3, you can set the standby mode to either S1 or S3, not both, in the BIOS. Note that Windows cannot choose which standby mode to run. You have to set it in the BIOS.
For S4, you can only set it in Windows 2k/XP (and ME, but not 98).
10. Others
Q: I have MSI FX5900 which has double sided fans, can it fit in the board?
Most boards can fit the FX5900. Including, the NEOs' MS-6728, MS-6758, and others like KT4A ultra, MS6777 Nvidia board.
Q: Why my NB Temp value is always stay the same?
On 875P Neo and 865PE Neo2, there is no NB temp sensor! The value you read from CoreCenter does not mean anything. Please update to the latest CoreCenter.
Q. What are the two lights on my "P" series board for?
A. These are the Overclock Signal Lights:
1. Green, Green: Both AGP and CPU are dynamic overclocking.
2. Green, Red: The memory is overclocking to 533MHz.
3. Red, Green: The external frequency is overclocking to 350MHz, and the frequency between the north bridge and CPU is 1400MHz.
4. Red, Red: CPU is dynamic overclocking now.
There are more to come soon. Please do not reply or request for FAQ contents in this thread. The FAQ will be picked up from the popular threads. Thanks.
Update History:
6/23/2003 : Added onboard sound lost fix
6/25/2003 : Added HDD LED
6/26/2003 : GOOD NEWS!! MAT to be available in all Neo2 boards!
6/27/2003 : SATA, PATA
7/1/2003 : 865G MAT support!!
7/7/2003 : MAT + DOT support
7/7/2003 : Prescott CPU support
7/7/2003 : DDR266 RAM support for 800MHz FSB CPU
7/17/2003 : Prescott CPU support UPDATED
7/18/2003 : SATA & PATA updated
8/15/2003 : latest BIOS updates
8/15/2003 : RAID-1 support for ICH5R
8/16/2003 : RAID configuration
9/02/2003 : beta BIOS updates - 1.81B
9/03/2003 : beta BIOS update for 865 - 1.52B
10/03/2003 : beta BIOS update for 875 - 1.9B3
10/06/2003 : beta BIOS update for 865 - 1.6B2
10/08/2003 : beta BIOS update for 865 - 1.7B1 link provided
10/13/2003 : minor updates on old issues
10/16/2003 : NB temp sensor?
10/19/2003 : Promise IDE3 for non-RAID function
10/20/2003 : Prescott updates
10/21/2003 : FSB:DDR ratio
11/21/2003 : Legacy, Native mode, SATA+PATA Configuration
12/01/2003 : BIOS 1.9B6 for 875P
12/15/2003 : Prescott Support, 250GB HDD support, BIOS 1.9 FINAL
1/11/2004 : BIOS 2.01B for 865PE Neo2, BIOS 3.30 for 865PE Neo2-P
1/12/2004 : USB 2.0 [thanks to Danny for contribution]
1/26/2004 : SATA + PATA Revisited
1/26/2004 : Added 8. CPU [contributed by Danny]
1/27/2004 : Added formatting SATA HDD in WinXP
1/28/2004 : updated on SATA+PATA and links with Danny, Vango44 and Uruk Hai's contributions :biggthumbsup:
1/28/2004 : Added power management
04/05/2004 : Added two lights on "P" series boards [Danny]

Dear [Maesus],
I have tried to duplicate the issue, I saw it only once when I reflash the BIOS and then change the CPU clock setting.
My procedure as below…
1. Boot system
2. Update BIOS to 1.9 version
3. Restart the system to BIOS setting
4. Change the CPU Bus Clock to 229
5. Save the setting & exit and then the system restart automatically
6. And then I saw the CPU is only running 1.86GHz (my CPU is 3.2GHZ FSB 800MHz)
But I would like to explain that my procedure as above is incorrect.
The correct procedure should be as below….
1. Boot system
2. Update BIOS to 1.9 version
3. Restart the system to BIOS setting
4. Load BIOS setup default first
5. Change the CPU Bus Clock to 229
6. Save the setting & exit and then the system restart automatically
7. And then I saw the CPU is running 3.66GHz (my CPU is 3.2GHZ FSB 800MHz)
Note: To load BIOS setup default setting after reflash BIOS that is because all original default setting will be erase after upgrade BIOS. So we always recommend customers to load BIOS default setting first before change any BIOS setting.
BTW, we have updated the BIOS version to support Prescott CPU. Users can decide to update it or not.
The new release BIOS as attach file.
Best regard!
[MSI Staff]

SG 200-26 led system parpadea intermitentemente

Similar Messages

Maybe you are looking for