SG 300 and Cisco Configuration Assistant
Hi guys I'm having trouble in connecting a SG 300 switch with CCA v3.2. I have already connected the switch with CCA, however I can't see anything in my CCA's Front Panel and Topology view.
Here is the view of my Front Panel view after I connect the switch :
Could you guys please help me to find what the problem is?
Thanks a lot!
Hi Robert,,
Thanks for your reply. I found out that the problem was caused by the firmware, just like what you said.
I have upgraded the firmware, and now the switch is able to connect properly.
Similar Messages
-
Configure SG500X using Cisco Configuration Assistant (CCA)
Hi,
I have a couple of SG500X Switches which need to be configured and I wanted to do this with a central managed tool to have an uncomplicated way to configure the switches.
I already found Cisco Configuration Assistant, which supports the 200 and 300 Series but does not seem to support 500 Series. Also I found the Cisco Network Assistant which only supports Catalyst Switches.
Is there a tool which can be used to centrally configure and manage SG500X switches?
Thanks in advance,
Christophpush
Is there really no tool for the 500 Series?
Seems strange to me, as 300 and lower have the CCA and Catalyst have CNA, only the 500 don't have any tool. -
ISM-SRE-300-K9 & Cisco Configuration Professional Issue
hi there,
i have a cisco 2901 router running CME 8.6 the router has a ISM-SRE-300-K9 card init with Unity Express 8.0.5 installed.
i am having issues with Cisco configuration professional and configuring the module
under module configuration the status is "module is not reachable", if i click on details i get further information "unable to execute command from the module. module is either reloading or is in failed state. you must make the module up and refresh the module"
i have tried reloading, resetting and refreshing the module but the issue is still present
i have accessed the module from the CLI set it in offline mode and factory defaulted it and the same issue is still present
the only thing i can think is that this is a bug with CCP as the loopback interface which the module is using can be pinged fine from the router so the message makes no sense.
any ideasIs you problem with CCP or the module itself ?
Because, CCP bugs and limitations aside, the module can be normally be installed, configured and managed using CLI or its web interface (after software is initially loaded). -
ESW-520-24-K9 and Cisco Network Assistant
HI,
Is this switch model ESW-520-24-K9 is supported by Cisco Network Assistant.
In the leatest release notes of CNA are supported Catalyst Express 520 Series Switches and this model WS-CE520-24TT-K9 is on the supported list.
But the mention model above is EoL and the new one is ESW-520-24-K9.
Thanks,
KamilHi Dave,
Thanks for your replay.
Yes, you are right that this switch model is supported by CCA but not by Cisco Network Assistant.
These programs are different in functionality.
The situation has become clearer, since the customer bought the Cisco Catalyst 2960 series switch.
Kamil -
2960S-48FPD and Cisco network Assistant
Hi all,
I'm using Cisco network Assistant V5.5 and when I try to discover WS-C2960S-48FPD-L I have this message :
Unsuported device type ... cannot add device to commuity
Any have a solution to that problem ??
Thank's, LaurentHi Laurent,
This switch is not supported by Cisco Network Assistant yet. -
WS-2960-48TC-L and Cisco Network Assistant
Hello all!
I have WS-2960-48TC-L in
#show ver
Switch Ports Model SW Version SW Image
* 1 50 WS-C2960+48TC-L 15.0(2)EZ C2960-LANBASEK9-M
In Cisco Network Assistant (ver. 5.8.(9.1)) I can not add a switch to the community? And Why in Model string we have + (plus) but not - (dash)
Sorrry for my bad English.Hi Dave,
Thanks for your replay.
Yes, you are right that this switch model is supported by CCA but not by Cisco Network Assistant.
These programs are different in functionality.
The situation has become clearer, since the customer bought the Cisco Catalyst 2960 series switch.
Kamil -
10g installation stays at 45% during Database Configuration Assistant
Hi,
I am trying to install Oracle 10g in my windows XP machine.Installation goes on smoothly and the configuration assistant window appears.The Database Configuration Assistant page showing the progess bar for database creation also appears.The progress shows Clone database creation in progress at 45%. It has been running for more than 6 hours.
What should i do? Can i stop and run Database Configuration Assistant independently? Is installation of all oracle database component complete?
Please advice.
Regards,
JayHi,
I have checked and the Oracle listener is started.The problem is still there.
Where do i locate the files created during DBCA process? If there are any files left will they be replaced when i run DBCA independently?
Please advice.
Thanks.
Jay -
Database Configuration Assistant fails during instalation of Oracle EE 8.1.7
My machine runs RH 6.2 and I have tried to install it Oracle. After executing all pre-instalation steps, I run ./runInstall and instalation process goes on. I select Typical Instalation and instalation proceeds until 100%, when OUI tries to configure Net 8 Assistant and Database Configuration Assistant. Both applications fail in this phase. Unfortunately, OUI shows a message (Database Configuration Assistant) informing that /u01/.../JRE/bin/jre does not exist. However, I have installed JDK 118 and JRE link seems correct, so that I can access JDK directory throught JRE link.
HELP, HELP!!!
Cheers,
Andresome good installation guides to check out:
http://www.akadia.com/services/ora_linux_install_901.html
http://www.e-gineer.com/instructions/install-oracle9i-on-linux.phtml
good luck!
Jenny -
Database Configuration Assistant fails during installation Oracle EE 8.1.7
My machine runs RH 6.2 and I have tried to install it Oracle. After executing all pre-instalation steps, I run ./runInstall and instalation process goes on. I select Typical Instalation and instalation proceeds until 100%, when OUI tries to configure Net 8 Assistant and Database Configuration Assistant. Both applications fail in this phase. Unfortunately, OUI shows a message (for Database Configuration Assistant) informing that /u01/.../JRE/bin/jre does not exist. However, I have installed JDK 118 and JRE link seems correct, so that I can access JDK directory throught JRE link.
HELP, HELP!!!
Cheers,
Andresome good installation guides to check out:
http://www.akadia.com/services/ora_linux_install_901.html
http://www.e-gineer.com/instructions/install-oracle9i-on-linux.phtml
good luck!
Jenny -
How to start iSQL*Plus configuration Assistant on Command Line?
I have almost successfully installed oralce 10gR2 in opensolaris 5.11, In the final stage, Among the three Configuration Assistants:
the Net Configuration Assistant and Database Configuration Assistant have completed successfully, but OUI hang in the iSQL*Plus Configuration Assistant.
No response after a very long time.
Could anybody tell me how to manually start iSQL*Plus configuration Assistant on Command Line?
Thanks a lot !
Edited by: user11970554 on 2009-10-5 上午9:21Thanks.
Anyhow, I found an easier way to do this:
1)Just run installer again to start the OUI:
#./runInstaller
2)Choose "Custom" installation option
3)check the box at "iSQL*Plus" for reinstall
4)The OUI will first deinstall iSQL*Plus, and then reinstall it, and will automatically start "iSQL*Plus configuration Assistant".
This procedure applies to any component of oracle which failed at first time installation. -
Failed configuration assistants
During my install, I had a failed configuration assistant - Application Server Control Configuration Assistant
Since it failed, the install skipped DCM Repository Backup Assistant.
I finished the install anyways and rebooted the computer.
How do I re-run only the failed and skipped configuration assistants.
Thanks.go to $OH/cfgtoologs, and there should be a file that is like a script of the configuration assitants that where failed or skiped.
Greetings. -
Cisco Network Assistant and add to comunity problem via HTTPS
hello,
i have big network of cisco switches and all is in my cisco network assistant in comunity connected via HTTPS. if i add new switch to network (all for HTTPS access is configured good: domain name, ip http secure-server, authenticate locale ...) and if i can add this switch to comunity (right click on icon and ADD TO COMUNITY), CNA say "Unable to Connect", because it can connect to switch via HTTP (i have disable it on switch), not via HTTPS. i have never version of CNA ... where is problem? why it not connect to switch via HTTPS? hmmm? thank you ... Peter"The HTTP server interface must be enabled to display the network assistant. " Source.
You can put an access-list on the http server if you are concerned about security exposure. -
Username and password for configuration assistant
I've installed the web configuration assistant for the first time and am being prompted for a username and password. What am I supposed to use? I've tried several. Thanks.
I don't think so. It's the web application to maintain Oracle Utilities application users and access among other things. I found the problem. First, I was missing the proper access (env_access) and a row was missing in env_code. Thanks.
-
How to run Net Configuration Assistant on 10g Forms and Reports server
I have a Windows 2000 server with Forms and Reports Services installed from AS 10g v. 9.0.4 (just the Forms and Reports install). According to the OUI, Net Configuration Assistant 9.0.4 is also installed. However I cannot figure out how to run the Net CA. There is no shorcut that I can find. Can anyone help?
Thanks for the reply Frank. I have looked all through the Start menu but see no "Configuration and Migration". I assume it's because I only installed the Forms and Reports option, so I only have Forms Services, Reports Services, and the Universal Installer. No big deal - I've already setup tnsnames manually. I just like to use the Net Assistant when I can.
-
Database Configuration Assistant for 8.1.61 and Red Hat 6.1
This is my first install and I'm a little confused.
Im installing Oracle Enterprise 8i release 2 (aka 8.1.6.1) on a Linux box (Red Hat 6.1). When Oracles Installer gets to the Database Configuration Assistant, it runs for awhile and then gives me this error:
ORA-03114 not connected to ORACLE
When I click OK to dismiss the message, it just hangs there. If I get to a shell and kill off a few of the DbCA processes, I eventually get back to the Installer and I can Exit. It says that the installation was successful but the sample database was not created.
Ive tried this twice now. Same result each time.
nullHi,
I've got the same problem. dbassist and svrmgrl give me the same errors.
I'm using Oracle 8.1.6.1.0 on Mandrake 7.1. With the 2.2.15-4mdksecure kernel.
SVRMGR> CONNECT INTERNAL
Connected
SVRMGR> STARTUP NOMOUNT
ORA-00445: background process "PMON" did not start after 120 seconds
SVRMGR> (SQL stuff...)
ORA-03114: not connected to ORACLE
Any ideas?
This is driving me nuts!!!
Thx
Johan
null
Maybe you are looking for
-
Hello everyone. Well, here's another question... I have a 1.5T RAID 5 system for the Mac. On the PC, I put most of my CD / DVD movies/videos on the hard drives as a disc image. That way I have full access to my library without using my DVD drive. I w
-
Sender File adapter not picking the file ABCD.PRN extension file
Hi Am doing File to Abap Proxy scenario. My source will be in text format of fixed length of fileds 7. My souce file will be generated by a third party machine with the extension EEE150809.PRN. In my scenario my file adapter should pick the file and
-
What's the model number for my HP tablet
HP provides a type of model name near the screen of your tablet, but this name or number might not be sufficient to get proper support for your tablet. These names or numbers might represent a series of tablets that look similar but have different op
-
AppServer crashes. Need help troubleshooting
After following the guidance and completing the installation I have noticed AppServer will crash intermittently. It could happen after 5 mins running or 15. Here's the log in /opt/SUNWappserver/domains/domain1/logs/server.log [#|2008-10-10T00:08:47.6
-
Need a sample coding for function module MRM_DBTAG_RSEG_READ
hi, I am working on reports. I was asked to use the function module MRM_DBTAG_RSEG_READ for retrieving the line item information. I tried using the fucntion module, the problem i am facing in the declaration of the internal table I_TE_RSEG for the pa