SG-500-28P How to view mac address table?

The standare Cisco IOS command is show mac-address-table. This command isn't available on this switch.
FW v1.3.0.62
Thanks.

Show mac address-table

Similar Messages

  • How to view MAC addresses on the network?

    I can log into other non-apple routers via browser and see a list of MAC addresses of equipment connected to the network, but I don't see how to view them if using my Airport Extreme and going in through Airport Utility.
    Any thoughts?

    If It's the same Mac that can see the PC, it's already set up correctly. Something must be wrong somewhere.

  • How to see mac address in IPS 4240 ???

    Hi all,
    How to see mac-address of inline-vlan-pair ?  and how to see mac-address of management interface in IPS ?
    Regards,
    Kiran

    Hello Kiran,
    The inline-vlan-pair itself is tied to a particular interface. So you're really asking for the MAC address of the interface associated with the inline-vlan-pair.
    The MAC address of sensing ports will be added to a "show interfaces" via CSCse84414. You can currently view the MAC address of sensing interfaces by doing an "ifconfig -a" from the service account.
    Thank you,
    Blayne Dreier
    Cisco TAC IDS Team
    **Please check out our Podcast**
    TAC Security Show: http://www.cisco.com/go/tacsecuritypodcast

  • How to block mac address in 2800 router

    sir
    how to block mac addresses in cisco 2800 router 

    Hi,
    To block mac addresses you can simply create Mac based ACLs which ranges between 
    700 to 799
    Example:
    access-list 700 deny xxxx.xxxx.xxxx.xxxx
    access-list 700 permit yyyy.yyyy.yyyy.yyyy
    now you can apply it on interface:
    int f0/0
    access-group 700 in 
    exit
    Regards,
    Rahul Chhabra
    Network Engineer
    Spooster IT Services

  • How to get MAC address from IP address in LAN

    Hi all,
    How to get MAC address from IP address in LAN (windows or any OS), I would have all IP addresses of my LAN, so I would like to know all MAC address.
    Code examples are highly appreciated.
    Thanks & Regards,
    abel...

    abel wrote:
    Yeah that is only working for local system, but how to get remote system's MAC ..?
    Thanks for quick reply ...
    Edited by: abel on Jan 28, 2009 12:10 AMIt is my understanding that only one person ever found the holy grail which you seek. But sadly [_he's dead_|http://forums.sun.com/profile.jspa?userID=649366]
    As a curious aside how did you manage to get the list of IPs?

  • How to find mac address of a client computer in specified time and port in WIFI WCS Control system

    how to find mac address of a client computer in specified time and port in WIFI WCS Control system

    WCS record-keeping is very crude.  
    You'll get the time/date when the client authenticated.  You'll get the local inside address but you'll need the router to translate the outside IP address and the port.  
    You will need a proxy server to determine what sites did a wireless client goes.

  • How to change mac address on mac

    i'm sry i'm not sure if this is the right section or not but yeah.... nyways does anyone know how to change mac address on a macbook?

    If you have not updated your OS you can use the following command.
    sudo ifconfig enX ether xx:xx:xx:xx:xx:xx
    You will need to replace the X with your network number and the xx:xx:xx:xx:xx:xx with the mac you want to have.
    Then run
    sudo ifconfig enX down
    sudo ifconfig enX up
    This change will last till your next reboot.
    cheers
    NOTE: This is not working in 10.5

  • How to change mac address on time capsule

    Hi there,
    How to change mac address on time capsule?

    There are routers that allow you to create/clone a mac address to whatever you like. Since many companies use the mac address to 'register' a unit connected to it's system, you usually just have to let them know you've changed your router and they will reset your system to accept connections from the new device.

  • How to change mac address on wrt54g router

    How to change mac address on wrt54g router?

    are u sure u wanna change the MAC of the WRT54G ?  it's not possible....you can however clone the MAC address of your PC onto the router...depending on your ISP.

  • How to check MAC address from host from local network

    Hello,
    I must save information about my network enviroment, at some periods of time (IP, Host Name, MAC Address, and later some information from SNMP). I have IP addresses of all devices. Could any one have an idea how to check MAC address. In java.net.* I didn't find anythink about my problem.
    Please give my an answer, if you konow any solution.
    Marcin Kowalski

    hi !
    I've typed ipconfig on my PC which has windows2000 pro. as the OS!!
    but i couldn't get th line you've mentioned "Physical Address" !!
    what could be wrong .. ?!! hope you could help!!
    thanks!!
    C:\>ipconfig
    Windows 2000 IP Configuration
    Ethernet adapter
    Connection-specific DNS Suffix . :
    IP Address. . . . . . . . . . . . : 10.130.128.210
    Subnet Mask . . . . . . . . . . . : 255.255.255.0
    Default Gateway . . . . . . . . . : 10.130.128.1

  • How can I see the mac address table of a vSwitch

    I am having some ARP collisions on my network and have determined that the offending mac address belongs to VMWare. I have already looked at the mac address tables of my physical switches but can't find the VMWare mac address I'm looking for. I would like to look at the mac address tables of the standard vSwitches to try to track down the root of the problem, but I fear that is not a possibility.
    Does anyone know a method to display the mac address table on a vSwitch?

    Hi midi25,
    >>I would like to be able to see what devices are connected and if possible remove any stale entries.
    Hyper-v virtual switch doesn't need us to manually maintain that "table" like a physical switch .
    Best Regards,
    Elton Ji
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] .

  • CNA 5.5 and show mac address-table

    When trying to Monitor/Search for MAC address in C2960 network I got an error reply that a CLI command is not supported. Analyzing network traffic shows that CNA 5.5 is issueing 'show mac-address-table' command but the latest Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(55)SE does not support 'show mac-address-table' anymore but does support 'show mac address-table' command. How can I change the command for showing mac address tables in CNA 5.5?
    M.

    hi john,
    the show mac-address-table command should be valid.
    check if you've got MAC learning enabled on the ASA interface using show mac-learn command.
    edit: could you post show firewall? the above command works on transparent firewall only.

  • Mac address table corruption?

    We are running Cisco 4500 chassis at the access layer, and have been for a few years without issue. Recently we started to experience issues where a mac address will just randomly "jump" to another port. User will call us and say their computer is not working. We will locate the mac, and its showing on the wrong port. We shut that port, do a no shut, and the mac jumps back to the correct port. In the example below, the mac address jumps to port 3/2, but is physically connected to 2/12.
    !--issue before shut/no shut
    mdf#show mac address-table | inc 9ebf
     236      782b.cb8c.9ebf    static ip,ipx,assigned,other GigabitEthernet3/2  
    !--port security knows the correct info however
    mdf#show ip dhcp snooping  binding | inc 9E:BF
    78:2B:CB:8C:9E:BF   xxx.xxx.236.193   76145       dhcp-snooping   236   GigabitEthernet2/12
    mdf#show mac address-table int gi2/12
    Unicast Entries
     vlan     mac address     type        protocols               port
    ---------+---------------+--------+---------------------+-------------------------
    3908      20bb.c021.ae58    static ip,ipx,assigned,other GigabitEthernet2/12   !--ip phone
    mdf#show mac address-table int gi3/2
    Unicast Entries
     vlan     mac address     type        protocols               port
    ---------+---------------+--------+---------------------+-------------------------
     236      1803.7339.d93d    static ip,ipx,assigned,other GigabitEthernet3/2         
     236      782b.cb8c.9ebf    static ip,ipx,assigned,other GigabitEthernet3/2         !--mac in question
     236      782b.cb8c.c366    static ip,ipx,assigned,other GigabitEthernet3/2         
    3908      b414.89a2.2ae0    static ip,ipx,assigned,other GigabitEthernet3/2   
    !--fixing issue
    mdf(config)#int gi3/2
    mdf(config-if)#shut
    !-- issue resolved
    mdf#show mac address-table | inc 9ebf
     236      782b.cb8c.9ebf    static ip,ipx,assigned,other GigabitEthernet2/12
    Switch is running cat4500e-entservicesk9-mz.151-2.SG2.bin , but also happened on cat4500e-entservicesk9-mz.151-2.SG4.bin and cat4500e-entservicesk9-mz.150-2.SG4.bin. Other switches have also had this issue occur.

    Looks to be me like a bug.
    could you please provide me some more details on this:
    1- How often this issue is occurring?
    2- Is this occurring to specific ports or specific laptops which are connecting to this ports or is it irrespective of devices?
    3- Is there any possibilities that you try rebooting one of the switch if the issue is very often? (I know this is not a feasible solution , I know it is some issue iwth the firmware but in case to avoid high impact you can reboot the switch and update me?
    4- Provide me with the logs from the switch?
    5- I will do the bug scrub and let you know.
    HTH

  • MAC address table vs. CAM table

    MAC address table vs. CAM table. How they are different?

    I don't believe there is a difference as such. CAM simply refers to the way the switch uses memory (in a content-addresable) manner to look up the MAC address to port association.
    Paresh

  • Mac address table on a PIX

    What am i missing?
    pixfirewall# show mac-address-table
                       ^
    ERROR: % Invalid input detected at '^' marker.
    [EDIT: karat is under the A in mac ]
    pixfirewall# sh ver
    Cisco PIX Security Appliance Software Version 8.0(4)
    Device Manager Version 6.1(3)
    Compiled on Thu 07-Aug-08 19:42 by builders
    System image file is "flash:/image.bin"
    Config file at boot was "startup-config"
    pixfirewall up 175 days 11 hours
    Hardware:   PIX-525, 256 MB RAM, CPU Pentium III 600 MHz
    Flash E28F128J3 @ 0xfff00000, 16MB
    BIOS Flash AM29F400B @ 0xfffd8000, 32KB
    0: Ext: Ethernet0           : address is 000d.28f9.62a5, irq 10
    1: Ext: Ethernet1           : address is 000d.28f9.62a6, irq 11
    2: Ext: Ethernet2           : address is 000d.8810.a620, irq 11
    3: Ext: Ethernet3           : address is 000d.8810.a621, irq 10
    4: Ext: Ethernet4           : address is 000d.8810.a622, irq 9
    5: Ext: Ethernet5           : address is 000d.8810.a623, irq 5
    Licensed features for this platform:
    Maximum Physical Interfaces  : 6
    Maximum VLANs                : 25
    Inside Hosts                 : Unlimited
    Failover                     : Disabled
    VPN-DES                      : Enabled
    VPN-3DES-AES                 : Enabled
    Cut-through Proxy            : Enabled
    Guards                       : Enabled
    URL Filtering                : Enabled
    Security Contexts            : 0
    GTP/GPRS                     : Disabled
    VPN Peers                    : Unlimited
    This platform has a Restricted (R) license.
    Serial Number: 807234146
    Running Activation Key: 0x6ab205ba 0x986d4239 0xf56523af 0x76f3d58b
    Configuration last modified by enable_15 at 12:58:08.130 EDT Thu May 16 2013
    pixfirewall# show mac-address-table
                       ^
    ERROR: % Invalid input detected at '^' marker.

    Hi,
    Command Modes The following table shows the modes in which you can enter the command:
    Command Mode
    Firewall Mode
    Security Context
    Routed
    Transparent
    Single
    Multiple
    Context
    System
    Privileged EXEC
    Source:
    http://www.cisco.com/en/US/docs/security/asa/asa80/command/reference/s4.html#wp1448364
    - Jouni

Maybe you are looking for