SG-500 - SNMP OID for CPU Load?

Hello,
i have several SG500 (Standalone and stacked). How can i get the CPU Load via SNMP? Who knows the correct SNMP OID for CPU Load?
In the MIB which are provided as download a wasn't able to find the correct OID.

Hello,
There are three OIDs available for CPU usage:
CPU utilization for 5 seconds
.1.3.6.1.4.1.9.6.1.101.1.7.0
CPU utilization for 1 minutes
.1.3.6.1.4.1.9.6.1.101.1.8.0
CPU utilization for 5 minutes
.1.3.6.1.4.1.9.6.1.101.1.9.0
This came from a scrap note I had in an e-mail, so I am not exactly sure where this information is originally.
Let me know if that works for you,
Christopher Ebert - Network Support Engineer
Cisco Small Business Support Center
*please rate helpful posts*

Similar Messages

  • SNMP OID for CPU and Memory Utilization on a MDS 9509

    Does anyone know what the OIDs are for CPU and Memory utilization on a MDS 9509?
    Thanks

    CISCO-SYSTEM-EXT-MIB.my is a good place to start and you can determine the OID from the MIB.
    Once you feel as though you are on the right track, have a look at:
    http://www.oidview.com/mibs/9/CISCO-SYSTEM-EXT-MIB.html
    I gather that what you need is:
    1.3.6.1.4.1.9.9.305.1.1.1
    and
    1.3.6.1.4.1.9.9.305.1.1.2
    Enjoy.
    Stephen

  • Snmp alerts for CPU utilization

    Hi,
    I want to enable snmp alerts on l2 and l3 switches to monitor CPU utilization.
    I have Opmanager which is acting as SNMP server.
    I have switches L2 and L3 which are running IOS 12.0, 12.1, 12.2
    Do all these IOS versions support SNMP alerts?
    And also I want to know the commands to be configured on switches for this.
    Regards
    skrao

    You can configure SNMP traps for CPU Thresholding Notification.
    http://www.cisco.com/en/US/products/ps6350/products_configuration_guide_chapter09186a0080455772.html
    You should be ok with the versions you list but check exact IOS version supports it at http://www.cisco.com/go/fn
    If you do not want to use traps then there are specific oids that can be polled for 1minute average (1.3.6.1.4.1.9.2.1.57) and also 5 minute average (1.3.6.1.4.1.9.2.1.58). I've used these in the past with no problems. These oids may have been superceeded so check for latest. You can always snmpwalk a device to check oids.
    The cisco SNMP navigator is helpful when it comes to oids.
    http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?local=en
    If you haven't got any SNMP configured yet on the switch check out http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Network%20Infrastructure&topic=Network%20Management&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1ddb4e54
    HTH
    --Phil

  • OID for CPU and MEMORY utilization for wrv4400n

    Hi,
    Can any one please tell me the OID for CPU and MEMORY utilization for wrv4400n?
    Thanks
    Vipin

    CISCO-SYSTEM-EXT-MIB.my is a good place to start and you can determine the OID from the MIB.
    Once you feel as though you are on the right track, have a look at:
    http://www.oidview.com/mibs/9/CISCO-SYSTEM-EXT-MIB.html
    I gather that what you need is:
    1.3.6.1.4.1.9.9.305.1.1.1
    and
    1.3.6.1.4.1.9.9.305.1.1.2
    Enjoy.
    Stephen

  • Snmp oids for the command "show counters interface intx/y delta"

    Hello,
    I have a question about SNMP OIDs for the command "show counters interface intx/y delta" on Catalyst6500. The customer wants to create graphs for the following values:Overruns, qos0Outlost, InErrors, OutErrors, InDiscards, OutDiscards etc..
    Is possible to get these values using SNMP??
    Thank you
    Roman

    Thank you, Dan. These OIDs are for the output from the command "show interface int x/y". But I think, that these OIDs are not for the command "show interface int x/y delta".
    Roman

  • SNMP OIDs for solaris 8

    Hello
    Someone could tell me where to find a list of SNMP OIDs for solaris 8
    thank you for your cooperation

    Thank you, Dan. These OIDs are for the output from the command "show interface int x/y". But I think, that these OIDs are not for the command "show interface int x/y delta".
    Roman

  • Cat6509 - SNMP OIDs for interface stats

    Hello,
    I have a Catalyst 6509-E-VSS with IOS 12.2(33)SXI3.
    I'm looking for OIDs to retrieve the same counters I get with the commands
    "show interface stats" and "show interface switching".
    I want to graph the number of packets that are process switched.
    The OIDs from IF-MIB (  ifInOctets, ...) show only the total number of octets not the
    switching path.
    Thanks for help
    Mike

    After a long time silence on this frontier the problem is comming up again.
    My goal is still to find out, what interface causes process switched traffic.
    There is usualy a lot of traffic handled in software but sometimes (of course on weekend midnight) it seems to increase the cpu load (IP Input process).
    Regarding the Cisco document "Troubleshooting High CPU Utilization Due to the IP Input Process" I want to monitor traffic by switching path.
    So again - does anybody has an idea to get these counters with snmp ?
    Update: IOS is now 12.2(33)SXJ3

  • Reading SNMP OID for used storage on px12-400r

    Hi, does anyone know how get the correct value for used disk space via snmp on the px12-400r nas?
    All capacity is configured as one big cifs share. I want to monitor the usage of space with snmp.
    If I do a snmpwalk (v3) I can pinout the filesystem /mnt/pools/A/A0 on OID 1.3.6.1.2.1.25.2.3.1.3.38.
    If I read the oid for StorageUsed I get a strange negative value: -1084997477
    This value changes while data are written to the cifs share so it seems to be monitoring. But what to do with this negative value?
    Thanks for any help!
    /Anders

    Hello anders-px12-400
    I recommend checking with rtrevino from his thread.   The unit's are different, but the firmware is bascially the same across all Lifeline devices
    LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
    US and Canada: https://lenovo-na-en.custhelp.com/
    Latin America and Mexico: https://lenovo-la-es.custhelp.com/
    EU: https://lenovo-eu-en.custhelp.com/
    India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
    http://support.lenovoemc.com/

  • SNMP OID for DHCP on Server 2012

    We recently installed Server 2012 standard on one of our servers and were trying to keep a graph of DHCP lease use. Anyway the OIDs for DHCP in Server 2008 R2 started with "1.3.6.1.4.1.311.1.3.2.1.1". If I try to snmpwalk these same OIDs on the new Server
    2012 (We the DHCP server configured and active), I get:
    Error in packet.
    Reason: (genError) A general failure occured
    Failed object: SNMPv2-SMI::enterprises.311.1.3.2.1.1
    I'm using SNMPwalk and I've never had a problem with this before. Any idea what would cause this? Thanks!
    Thanks!

    I'm having the same issue. OIDs just don't work against a 2012 DHCP server. I can snmpwalk other OIDs, just not DHCP :(
    Firewall has been disabled (and there were already adequate snmp rules allowing the traffic). Since I can query other OIDs, I'm ruling out firewall.
    Has this info been removed in 2012?

  • SNMP OID for 5108 Chassis input and output Watts?

    Anybody know these?
    Craig

    Craig,
    OID for cucsEquipmentChassisStatsTable --  1.3.6.1.4.1.9.9.719.1.15.10
    UCS MIBs are available here
    ftp://ftp.cisco.com/pub/mibs/supportlists/ucs/ucs-manager-supportlist.html
    HTH
    Padma

  • SNMP OID for Stuck CICs

    Hello,
    We have a PGW2200 and we are facing a stuck CIC problem. Im trying to monitorate it thru zabbix but I cant find the correct OID for the information. DOes anyone knows it, or can point me some document where I can find the OID ? I googled in many ways but for some reason I couldnt find the information.
    Best Regards.
    Luis Fernando Laimer

    When I use the command:
    rtrv-tc: it returns as follows:
    CIC=1,PST=IS,CALL=IN,BLK=NONE"
    CIC=2,PST=IS,CALL=IDLE,BLK=NONE"
    CIC=3,PST=IS,CALL=OUT,BLK=NONE"
    CIC=4,PST=IS,CALL=IDLE,BLK=NONE"
    CIC=5,PST=IS,CALL=IDLE,BLK=NONE"
    CIC=6,PST=IS,CALL=IDLE,BLK=NONE"
    CIC=7,PST=IS,CALL=IN,BLK=MATE_UNAVAIL"
    CIC=8,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
    CIC=9,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
    CIC=10,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
    CIC=11,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
    CIC=12,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
    CIC=13,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
    CIC=14,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
    CIC=15,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
    CIC=16,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
    CIC=17,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
    CIC=18,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
    Those identified by BLK=MATE_UNAVAIL wont work.
    I guess its an issue of our service provider, but for now I need to monitore the occorence of this situation.
    Best Regards

  • SNMP OID for Port & CPU Utilization

    I have a LinkSys SRW208P switch. Is it possible to retrieve Port & CPU Utilization using SNMP?
    If so, does anyone know the OIDs?

    SNMP sure does that. Default OID should work fine. Community password is set to "public" by default.

  • SNMP OIDs for ASR1k

    Hi everyone,
    We're trying to read CPU & MEM values from ASR1006 equipment. Obviously the old OIDs are not supported on this platform. This is what we have found by going through the snmp object navigator. (I assume .2 is the ESP, .3 is the RP, .4 & .5 are the SIPs). But the values we get from the command line are slightly different than what we get through snmp. Has anyone done this before? What OIDs do you use?
    =====================================================================
    CPU:
    1min: cpmCPULoadAvg1min
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.24.2; Value (Gauge):
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.24.3; Value (Gauge):
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.24.4; Value (Gauge):
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.24.5; Value (Gauge):
    5min: cpmCPULoadAvg5min
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.25.2; Value (Gauge):
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.25.3; Value (Gauge):
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.25.4; Value (Gauge):
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.25.5; Value (Gauge):
    15min: cpmCPULoadAvg15min
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.26.2; Value (Gauge):
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.26.3; Value (Gauge):
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.26.4; Value (Gauge):
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.26.5; Value (Gauge):
    ======================================================================
    Memory:
    cpmCPUMemoryUsed
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.12.2; Value (Gauge): KiloByte
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.12.3; Value (Gauge): KiloByte
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.12.4; Value (Gauge): KiloByte
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.12.5; Value (Gauge): KiloByte
    cpmCPUMemoryFree
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.13.2; Value (Gauge): KiloByte
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.13.3; Value (Gauge): KiloByte
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.13.4; Value (Gauge): KiloByte
    Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.13.5; Value (Gauge): KiloByte
    Best Regards,
    Babak  

    Thank you, Dan. These OIDs are for the output from the command "show interface int x/y". But I think, that these OIDs are not for the command "show interface int x/y delta".
    Roman

  • Is there a single snmp oid for flash and dram ?

    Does a single univeral oid (or 1 for flash and one for dram) exist that will provide total amount of flash and total amount of dram across all chassis families ?
    Thanks

    This link is your best bet:
    http://www.cisco.com/warp/public/477/SNMP/contiguous_memory.html

  • SNMP OID for AssociatedAPs in Virtual WLC 7.4.100.0

    Hello Guys!
    I need you help for something that I need to do to monitor my Wi-FI network.
    I'm using a Virtual WLC (SW Ver 7.4.100.0) where most that 30 APs are associated with, but I would like to monitor each disaciossiation of APs using SNMP. After some search, I have found this OID .1.3.6.1.4.1.14179.2.1.1.1.38 on some forums but it doesn't work, I see random number in my monitoring tool.
    Do you know if there is any another OID to use with this software version or maybe if I have to upgrade to ver7.6 or ver8?
    Thanks in advance,
    Kevin

    I'm assuming you don't own a license for Cisco Prime Infrastructure
    One thing you can do is send SNMP traps to your monitoring software from the WLC (I've never used virtual WLC but my assumption is most options are the same. If your software doesn't support SNMP Traps consider a different monitoring software...
    Go to Management > SNMP > Trap Receivers and set up your receiver
    Then to to Management > SNMP > Trap ControlsHere is where you set what traps are sent via SNMP. If you see the "AP" tab you can set several things.
    If you only want to see if an AP is dropping off the network and the above doesn't work, you could just put dhcp reservations on your APs and have your software ping it. This of course is only if its off network, not if it simply disassociates.

Maybe you are looking for

  • My experiences so far....

    My wife bought me the 3rd Gen as a birthday present around this time last year. After a number of months I started jogging a lot more, my Shuffle stopped working every time I went on the treadmill. I battled on a bit but eventually it completely died

  • New mac linked to existing xsereve account

    Our xserve was set up by someone who no longer works for the company. We had a break in the other night and 2 of our macs were stolen. When the replacements arrive how do  I set them up to log in to the existing xserve user accounts?

  • Screen or backlight problem - washed-out colors, fuzzy white overlay

    I've had my iPod for quite a long time now and have been living with this problem for at least a year. Some times, when I start using the iPod, the screen gets all washed-out with a fuzzy white overlay. It looks fine when the backlight turns off from

  • Table with n foreign key vs n tables or n foreign key vs 1 table?

    Hi, we have a scenario with n tables containing some attributes one table for one category of attribute (es: color, role, type, etc..) of a principal entity and 1 table for the principal entity with n foreign keys vs every attribute table. Some propo

  • BPEL Fault

    Somebody could help me with that error. I deploy a process that use 1 WSDL Document(BinesAsignadosWSDL.wsdl), when i try to create a process instance the follow error is thrown BPEL Fault: {http://schemas.oracle.com/bpel/extension}remoteFault{code=HT