SG200-26P not powering three access points.

Hello,
I just purchased a Cisco SG200-26P to power three Ubiquiti UAP-LR-3 UniFi AP that are going in a new small network. I added the three AP’s to port 1, 2, and 3 and they are not powering up off the POE switch. I got into the switch and I don’t see anything that stands out for them to not power up. The AP’s work powered up with POE injectors.
Thanks,
Minitrucker007

Hi Minitrucker,
SG200-26P is 802.3af compliant but from what I manage to read Ubiquiti UAP-LR is not 802.3af/at compliant, correct me if I am wrong as I did not really find the datasheet for your specific AP. This would mean that the AP would need the injector or specific switch rather than any. As it uses non standard PoE.
Regards,
Aleksandra

Similar Messages

Can not see wireless access point

I've wired both my laptop (windows7) and my wireless access point (wap54g) to my functional Neatgear switch. When I run the Linksys setup cd (from my laptop) I get the following message ...Can not locate a wap on this network. What am I doing wrong? Everything is powered up and all 3 lights on the wap are on.
Please help...

Have you tired to configure the WAP54G manually? If not you may try to connect your laptop directly to the access point's ethernet port and please make sure that the laptop has the same network IP as of the access point (192.168.1.***) then try to access the WAP54G set-up page via browser for you to configure it.

AC 5.31 not seeing wireless access points

We have a single image that is used for all of Lenovo / IBM laptops, T40, T60, T61, T42, T500. On the T40 I encounter issues with access connections from the get go, it does not see any wireless access points. Also does not seem to be the program managing it as windows wireless networks icon pops up saying wireless networks found, upon clicking on the icon I see quite a few available.I do not see this happening on my other laptops, I have attempted to remove AC and uninstall the wireless lan card only to run into the same issue upon reinstalling it.
Please help,
Thanks!

Hi,
sorry for late quesiton, but how does it looks with the current Access Connection?
I assuem ,you are using XP. Correct?
Please describe this situation a bit more , likewifi driver verison, MTM of the , or at least one affected machine etc.
Thanks
Rgrds

Macintosh os/9 not seeing my access points

I have a lab of 40 macintosh ibooks running OS/9 with the airport client. We recently replaced the Apple Airports with AP-350s running IOS 12.2(JA). Now, here is the problem. Ibooks running OSX work fine. the OS9's do not appear to be trying to find the APs. However, with the same scenario here in my office; if I turn on the Broadcast SSID option, the computer associates to the access point. If I turn off the Broadcast SSID option, the IBook seems to just do nothing, but it does give a 169.###.###.### IP address. When the Lab Tech took the Ibook back over to the lab, it did not work, even though I had turned the Broadcast on. They need these for a final next week. no pressure at all.

Try disabling the Aironet extensions feature on the Cisco APs. This feature is used by cisco wireless clients to exchange compatiblity information. Some of the non-cisco clients may not work with this feature enabled. Try disabling this. It should work.
For more information read http://www.cisco.com/en/US/products/hw/wireless/ps430/products_configuration_guide_chapter09186a0080606d4a.html#wp1135928

Cisco Network Assistant(CNA) not connecting to access points.

When I create a community with CNA, it finds the 2960 switch and connects to it. However it shows "connection failed" for all the 702i access points. Not sure why it shows connection failed. Any help would be appreciated.
Also, if I try to connect directly to the access point thru CNA, it says not accessible.
Thanks.
Jim

It will be helpful for other community members to know the solution and cause, if can be shared.
-Thanks
Vinod

My eprinter is telling me that my network name (ssid) does not match my access point network name.

I am using an HP photosmart D110a ePrinter with an ipad2 and I have inadvertently altered the network name (ssid) to the point that the wireles network test report says "that the (ssid) does not match my addess point network name (ssid) exactly." What do I do to put things right again?

Input the correct SSID into the printer and connect.
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

NCS 1.1 not showing any access points

Hi,
I have NCS 1.1 appliance and added a 5508 WLC running 6.0.199.4 code using snmpv3. Controller is added to NCS, but it doesnt show any AP's which are there on the controller. AP count is zero. I have another controller with code 7.0.230 added and showing AP's though. AP model is 1252. Any idea why this might be ?
regards
Joe

Leo is suggesting that your wlc isn't sending the info. Have you tried to remove and add the wlc again? NCS dies support that code version on the wlc, but you never know.
Sent from Cisco Technical Support iPhone App

Wireless bridging is not working in 1552 outdoor access point and 2602e indoor access point.

Hi,
I am have been tested wireless bridging with 2 indoor Cisco 2602 access point by following the attached document and its working fine without any issue.
After then I made one Cisco 1552 EU-M-K9 outdoor access point as RAP, then connect to this RAP with one 2602 mesh access point. But its not working, mesh access point is just start scan the signal to get associate with RAP, but not getting established. Is there any specific configuration required to connect between outdoor and indoor access point. Kindly find the attachment and advise.
regards,
Jubair.S

Hi Team,
Any suggestion??
Regards,
Jubair.S

Access Points not overwritten when restoring a bac...

Hi people,
Seems like the new and still buggy firmware of the E70 has another problem.
Before restoring a backup, if you do not remove the Access Point definitions (only operator Access Points, not Wi-Fi or others), the restore does not overwrite the definitions and makes new copies of the Access Points.
That would be OK if we could remove the extra Access Points but we cannot. When you delete one of the copies, it seems like it is removed but its definition is still somewhere on the phone, so while "Connection Settings" program cannot see it, all programs that use Access Points can see it (but cannot use it because it is a stale record).
Does anyone know where this info is stored so, if I forget to remove them before restoring a backup, I can remove them afterwards?
Kerem Erkan
IT Professional
E70 (2.0618.07.10 - 31.08.06 RM-10)

Welcome to the many problems of the LAPAC1750. I finally gave up and went with Ubnt. Uptime is at 75 days now and would've been longer if not for a firmware update.
The LAPAC had good range and worked well when it worked, but it's unstable to be marketed right now. Hopefully Linksys issues a firmware update to fix everything.

Access Points not joining WLC

Hello All,
I am trying to deploy several AIR-CAP3502E-E-K9 access points from a cisco 5508 wire lan contoller running ver 7 code. However iam having difficulty regiserting the access points with the WLC. The wlc is connect to a 3650 switch, and each access point is connected to a 2960 switch.
Problem Solved. A bad update was not allowing the access points to get their correct firmware.

You need to provide what Leo stated, that would help a lot. Anyways you can't telnet or ssh into a capwap AP if it has not joined the WLC. So that being said, provide the info Leo requested and then console into the ap and provide use with output from the console. Make sure you reboot the AP and then start capturing the output for around 5 minutes.
Sent from Cisco Technical Support iPad App

N800 no longer detecting any wireless access point

The device is working fine couple days ago, then today when I turn it on, the "connection manager" can no longer see any wireless access point. Not only my home network, also
my neighbor's wlan. My laptop can detect 10 networks
around my house. I try upgrad my os to the latest version and it is still not working. Is anyone has similar experience ? Is it a hardware problem ? Any advice will be
welcome.

It happened to my N800 too just a couple of days ago after I installed a number of applications. I have already removed those applications but the N800 still would not detect the access points that it usually detects with no problem.
It could not detect the WLAN inside our house even if the N800 was physically sitting on top of the router. It would intermittently detect my neighbor's WLAN (the one which I usually use) but it would not log on to it.
I tried removing the battery hoping to reset it but nothing changed.
It also would not connect to my PC via USB. The computer could not detect it. This one happened even before I installed those applications.
Help!!!!

No access point name on E51

i have already configured Access Point named MI. I use it to browse internet and many applications.
Whenever i open Nokia Internet Radio Application it does not show MI Access point but only shows Easy WLAN.
Can you help me to fix this

Big change some other app is using the connection at the same time.
‡Thank you for hitting the Blue/Green Star button‡
N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009

Need to disable AP mode multicast in 1231 series access point

Hi
I have one controller 2504 and some 1200 series access points.I am using 3 SSID .I want to use two ssid in HREAP mode but HREAP mode is not showinh in access point because multicast is enabled on AP mode.Please see the below picture
I have disabled the multicast globally from CLI.
config network multicast global disabled
Please help me in disabling the multicast so that i can set the access point in HREAP mode.
Thanks ....

Hi George
I have found a document in which it is mentioned which platform are supported..
These are the restrictions to remember while you use H-REAP.
Hybrid REAP is supported only on the 1130AG, 1140, 1240, 1250, 1260, AP801, AP 802, 1040, and AP3550 APs and on the Cisco WiSM, Cisco 5500, 4400, 2100, 2500, Flex 7500 Series Controllers, the Catalyst 3750G Integrated Wireless LAN Controller Switch, and the Controller Network Module for Integrated Services Routers.
But why it is giving an remark on controller tab that multicast is not supported with HREAP on this platform ?
Is this the limitation of cisco 2504 controller or the limitation of 1231 access point ?
Does that mean i can use my SSID in HREAP mode if i am using 1231 series access point ?
Thanks...

Help me find the required Wireless Access point

Dear Friends,
I am in search of a access point with below specification, so please let me know that which model has this functionalities.
. Wireless Access Point:
* No of port should be 10Base-T/100Base-TX Ethernet
* Standard should be IEEE 802.11g, IEEE802.11b, IEEE 802.3, IEEE 802.3u, IEEE 802.3af(PoE), 802.1q(VLAN) , 802.1X(Security authentication), 802.11i ready (Security WPA2), 802.11e ready (wireless QoS), 802.11F(Wireless roaming)
* LEDs should be power, PoE, Wireless, Ethernet
* Web Management should be built-in web user interface for easy browser-based configuration (HTTP/HTTPS)
* SNMP Support should be SNMP version 1, 2c, 3
* Operation modes should be access point made, point to point bridge mode, point to point multipoint bridge mode, repeater mode
* External antennas should be 2 (omni directional) SMA detachable
* Security should be WEP 64-bit/128-bit, WPA-PSK, WPA2-PSK, WPA-ENT, WPA2-ENT
* Access Control should be wireless connection control: MAC-based
* Wireless Security monitor should be Intrusion alarms(e.g. rogue client detected, spoofed MAC address) Denial-of-service alarms (e.g. duration attack, association table full) vulnerability alarms (e.g. access point is not using encryption, access point is broadcasting SSID)
* Power should be 12V 1A DC input, and IEEE 802.3af compliant PoE. Maximum power draw should be 3.36W

Hello Shekib,
All you did was describe the WAP200.
It fully fits in your description.
Please check it and see with your eyes.
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps10047/ps10048/data_sheet_c78-501966.html
I hope i helped you.
Regards.
Andrey Cassemiro.

Asking to enter a device password in the access point but I don't have an access point

I installed the Intel Proseet Wireless Client and upon connection to my Linksys router a wizard comes up asking me to "enter the device password to my access point or external registrar". It displays an 8 digit number in the device password field. My only option at that point is to go "back", "next" or "cancel". If I click "next" it eventually fails to connect to my wireless router. I do not have an access point installed. Only the router and cable modem. Any suggestions would be appreciated.
Message Edited by dougieg on 11-06-2009 05:12 PM

If its asking you for the Access Point password when you are trying to connect to your Wireless Network, It means you need to input the Wireless Security Key which you have setup on your Router.
When you are trying to connect to your Wireless Network and it ask you for the 8 digit password, you need to Flip your router upside down and below you will find a 8 digit pin number (0000-0000) it will be in these format. Just input the 8digit pin without (-) and click on Next and it will connect you to your wireless network. Once successfully connected to your Network wirelessly you should be able to go online Wirelessly from your Computer.

SG200-26P not powering three access points.

Similar Messages

Maybe you are looking for