SG300 - Separating network using vlan?

I am wondering what the best way to separate a network, both data, on a cisco SG300. I do not want network 1 to able to communicate with network 2 or vice versa.  I have one server for DHCP for network 1, 192.168.1.X. I would like network 2 to have ip of 10.0.0.X, can the cisco SG300 do dhcp for this vlan?
Thank you for your help,
Brian

Hello Brian, the SX300 series do not support any DHCP service, you will need a router or a DHCP box for this. The SX300 can separate traffic with VLAN. However, as the default layer 2, all request will go to your router then route to the destinations. As the switch in layer 3 mode, you may have local connectivity, however, if your router does not support the vlans or dot1q encapsulation, the router would require static routes for those subnets to be able to correctly route to the internet.
-Tom
Please rate helpful posts

Similar Messages

  • AX guest network using vlan in the switch

    Hi!
    I'm thinking of setting up a wlan and guest wlan by setting up separate Airport Expresses on different VLANs. The new gen. The setup would be 3 AXs on the internal network and 3 AXs as guest network. VLAN1 is internal and VLAN2 is guest. All AXs wil lbe set up in brigde mode. The AXs aren't VLAN aware so they'll just pass along whatever packets coming their way, right? I will configure the switch to use VLAN1 on all ports except 4 on VLAN2. 3 for the AXs and one to hte firewall that also provides DHCP for VLAN2.
    Would this work OR have i missed something vital here?
    /Hasse

    Thanks for the info, Unfortunately, as suspected the Arris model that you have is known as a "gateway", or "modem/router".
    The AirPort Extreme recognizes that there is another router "upstream" on the network, so it correctly chooses the Bride Mode setting to allow correct operation on the network.
    The downside to this is that the Guest Network cannot be enabled when the AirPort is configured in Bridge Mode.
    If the Guest Network feature is important to you, check with your service provider to see if they can supply a simple modem to connect to the AirPort Extreme.....not a "gateway" or "modem/router" device.

  • Trying to create guest network on wap321 and sg200-50p using VLAN

    I have a SG200-50P and a WAP321. I am trying to create a guest wireless network using a separate VLAN on the WAP321. I have the production traffic on VLAN 1 and the guest network is on VLAN 100.
    The WAP321 is plugged in to port 7 on the switch. It is configured as follows:
    Trunk Port, 1UP, 100T, Ingress filter enabled
    The DHCP server is on port 22 and is configured as follows:
    Trunk Port, 1UP, 100T, Ingress filter enabled
    The production wireless client is able to work fine on VLAN 1.
    When I try to connect a device using the Guest network, the DHCP request does not appear to ever make it to the DHCP server. If I separate the Production network off of VLAN 1 and change the Untagged VLAN ID to a different VLAN than 1 (Management VLAN ID), the same thing happens to the client when it tries to get an IP address from DHCP.
    What am I missing here?

    I have the VLANs configured on the WAP321. VLAN 1 is the Mgmt and general VLAN and the VLAN is configured for the Guest network. I did a Wireshark trace and for some reason the pakets for VLAN 100 (Guest network) on the WAP321 are not getting to the DHCP server. I see them on the WAP321 using the packet capture, but there is not any response to them. I do not see them coming in at the DHCP server.
    When I connect to the WAP321 using the production SSID I see the same ackets at the AP and also coming in to the DHCP server. That is why I am so confused. I can't figure out why they do not get to the server. I was wondering if I have something configured wrong on the SG200, but this is new territory for me and I do not know what I am missing. I have taken some screen shots of the SG and WAP config screens in case it might help.

  • Converting Flat network to VLAN

    Ok here is what I would recommend.You have your vlans setup, and the L3 mode set in the SG300 right?If so you will specify an IP address for the L3 router's interface on each vlan. For the sake of discussion lets say you have your business lan on VLAN 1, your guest network on vlan 100, and your servers on vlan 200 Your subnets are 172.16.1.0/24 for vlan 1, 172.16.100.0/24 for vlan 100 and 172.16.200.0/24 for vlan 200.The router's L3 interfaces will be 172.16.1.2 for vlan 1, 172.16.100.1 for vlan 100 and 172.16.200.1 for vlan 200.
    [Sidebar] There are a couple of things I want to point out here. Your vlan ID can be any number between 1 and 4095. I will typically setup the vlan ID to match the 2nd or 3rd octet in the IP address. That makes the vlan to ip address human identifiable. The computers or switches don't care, but from a...

    This is my first post after having read a lot and making little to no progress.I'm the SysAdmin at a small school and we are growing. My flat network is running out of IP addresses. So, given my limited budget, I switched my network backbone to a SG300-52 and am looking to VLAN setup my environment. I want to use Layer 3 switching and port by port VLAN.I've read several articles about how to do this with the SG300, but I just can't figure it out. I'm Sec+ certified, not CCNA so this is a little out of my league.
    Right now my setup is one DHCP server (Win 2008 server) and a FiOS router serving as the gateway. I would like to convert to being able to split my ports to differing subnets and have routing in between them to alleviate my IP address issues. I will still only have one DHCP server (which multiple scopes) and that one gateway. I...
    This topic first appeared in the Spiceworks Community

  • Multiple networks using single network adapter

    Hi,
    If I have only single network adapter in a OVM server (or  single bond interface bond0 created from two network adapters), is it possible to separate networks for
    VM management, live migrate and VM public networks using any mechanism, say by creating VLANs?  I am having two 10G adapters in each of the VM server
    and would like to separate traffic of each of these networks.  Thanks in advance.

    Hi,
    10G adapter is the best NIC performance so with two NICs like this, i recommand you to use the bond0 (mode 1) for fault tolerance and use the VLAN technology to separate the Networks.
    Note that Oracle VM support the VLAN configuration.
    I hope this can help you
    Best Regards

  • Using VLAN,s

    Well i have a single network with at the moment 200 cleints PC,s
    now i am merging 3 more networks with almost the same amount of PC,s so my network will grow 300%.
    now i have 7 servers running on my LAN which provides diffrent things such as email service, internet service, computer gaming service & huge data file transfer,s "files in GB's"
    my network is 10/100mbps & its not currently possible for me to upgrade to 1000mbps, so how should i use VLAN,s to optimize my network of best performace ?
    for starters i am going to use cisco 2900 switch this i already have.
    regards

    Hi Faisi,
    You can create vlans on your lan switches to create seperate broadcast domains but if you requirement is that all vlans should talk to each other then you need to have intervlan routing which is possible on layer 3 switch or some router.
    You can also create vlans for your server also and keep all your servers on those vlans and get the other vlans to talk to them via intervlan routing and can restrict other vlans to talk to each other.
    Like if you have vlans 3 for server and vlan 2 and vlan 1 for users you can have vlan 1 & vlan 2 to talk to vlan 3 but can restrict vlan 1 talking to vlan 2 but this is all possible if you have some layer 3 switch liek 3550 and above or some external router for intr vlan routing and configured access list to restrict traffic vlan wise.
    To create vlan you can just go to global config mode and create vlan
    Switch(config)# vlan 2
    Switch(config-vlan)# exit
    Switch(config)#
    Have a look at this link as how to create vlans on global config mode
    http://www.cisco.com/univercd/cc/td/doc/product/lan/cat2950/12120ea2/2950cr/cli3.htm#wp2879531
    HTH, if yes please rate the post.
    Ankur

  • Is there a way to create a virtual network using C# and the Azure SDK/API?

    I don't see a clear way to create an Azure Virtual Network using the SDK.
    I have all the methods to create the virtual network configuration, but no way to submit it:
    IList<string> VirtualNetworkAddressPrefixes = new List<string>();
    IList<string> LocalNetworkAddressPrefixes = new List<string>();
    IList<NetworkListResponse.DnsServer> DNSServers = new List<NetworkListResponse.DnsServer>();
    IList<NetworkListResponse.Subnet> Subnets = new List<NetworkListResponse.Subnet>();
    NetworkListResponse.Gateway Gateway = new NetworkListResponse.Gateway();
    IList<NetworkListResponse.LocalNetworkSite> LocalSites = new List<NetworkListResponse.LocalNetworkSite>();
    IList<NetworkListResponse.Connection> Connections = new List<NetworkListResponse.Connection>();
    VirtualNetworkAddressPrefixes.Add("a.b.c.d/cidr");
    DNSServers.Add(new NetworkListResponse.DnsServer() { Name = "TestDNS1", Address = "a.b.c.d" });
    Subnets.Add(new NetworkListResponse.Subnet() { Name = "Subnet-1", AddressPrefix = "a.b.c.d/cidr" });
    Subnets.Add(new NetworkListResponse.Subnet() { Name = "GatewaySubnet", AddressPrefix = "a.b.c.d/cidr" });
    Connections.Add(new NetworkListResponse.Connection() { Type = LocalNetworkConnectionType.IPSecurity });
    LocalNetworkAddressPrefixes.Add("a.b.c.d/cidr");
    LocalSites.Add(new NetworkListResponse.LocalNetworkSite()
    Name = "On-Prem",
    Connections = Connections,
    VpnGatewayAddress = "a.b.c.d",
    AddressSpace = new NetworkListResponse.AddressSpace() { AddressPrefixes = LocalNetworkAddressPrefixes }
    Gateway.Sites = LocalSites;
    Gateway.Profile = GatewayProfile.ExtraLarge;
    NetworkManagementClient netMgmtClient = new NetworkManagementClient(CloudCredentials);
    NetworkListResponse netlistresp = GlobalSettings.mainWindow.netMgmtClient.Networks.List();
    netlistresp.VirtualNetworkSites
    .Add(new NetworkListResponse.VirtualNetworkSite()
    Name = "TestVirtualNetwork",
    AddressSpace = new NetworkListResponse.AddressSpace() { AddressPrefixes = VirtualNetworkAddressPrefixes },
    DnsServers = DNSServers,
    Subnets = Subnets,
    AffinityGroup = "East US",
    Gateway = Gateway,
    Label = "LabelValue"
    I have also created the entire XML response and sent it to the NetworkManagementClient -> Networks.SetConfiguration() method, but it appears this command expects the virtual network to already be in existence. If anyone could give guidance, it would be
    appreciated.

    Hi,
    As discuss above , we have to create the XML response  ,before that first you have to
    GetConfiguration() details of existing virtual network. 
    string.format("@<NetworkConfiguration xmlns:xsd='http://www.w3.org/2001/XMLSchema' xmlns:xsi='http://www.w3.org/2001/XMLSchema-instance' xmlns='http://schemas.microsoft.com/ServiceHosting/2011/07/NetworkConfiguration'>
                <VirtualNetworkConfiguration>
                <Dns />
                <VirtualNetworkSites>
                <VirtualNetworkSite name=""{0}"" Location=""{1}"">
                <AddressSpace>
                <AddressPrefix>10.0.0.0/8</AddressPrefix>
                </AddressSpace>
                <Subnets>
                <Subnet name=""Subnet-2"">
                <AddressPrefix>10.0.0.0/11</AddressPrefix>
                </Subnet>
                </Subnets>
                </VirtualNetworkSite>",Networkname,location)+(@"<VirtualNetworkSite name=""demodsf1"" Location=""West Europe"">
            <AddressSpace>
              <AddressPrefix>10.0.0.0/8</AddressPrefix>
            </AddressSpace>
            <Subnets>
              <Subnet name=""Subnet-1"">
                <AddressPrefix>10.0.0.0/11</AddressPrefix>
              </Subnet>
            </Subnets>
          </VirtualNetworkSite>  </VirtualNetworkSites>
                </VirtualNetworkConfiguration>
                </NetworkConfiguration>")
    you have to append the node for existing node with new values , i got it its adding new virtual network 
    Best regards,

  • How do I extend my AirPort Extreme network using airport express

    How do I extend my AirPort Extreme network using airport express

    see http://support.apple.com/kb/HT4145 and other support articles
    and/or
    https://discussions.apple.com/thread/4462789?start=0&tstart=0
    and many other discussions on this forum about this topic.

  • Can I create a unique subnetwork when extending a wireless network using Airport Extreme?

    My office building has an Airport Extreme to provide wifi to our individual suites.  I would like to create a sub-network using my Airport Extreme for my suite only that uses the wifi signal from our office building and provides internet to the computers (both wired and wireless) in my suite but have it protected so that other suites in my building can't see my computers.  Is this possible and how do I do it?  I have currently set up my Airport Extreme in wifi-mode "extending a previous wireless network" and have the router with its unique router name.  But once I extended the wireless network, I could not find the network name of my router, only the office name (the one I was extending).  The computers connected via ethernet to my Airport have internet access but none of my wireless computers see my airport name, it sees the office building network name.  I'm assuming they are connecting to my Airport since the signal level is much higher than before and it appears that my Airport is rebroadcasting the network name of my office building.  Is there a way to have my Airport broadcast its unique identifier for wifi, still connect to the internet via wifi signal to the Office building airport and maintain segregation between my computers and the rest of my office building?
    Also, when I use the Airport Utility on my Iphone, I see the internet -> the office airport extreme -> and then 2 different base stations connected in a Y.  Mine and my neighbors (who is probably doing the same thing as I am).  But there is a dotted line to my base station, does that mean I'm connected to the internet via my neighbor's airport?
    Any thoughts?

    I would like to create a sub-network using my Airport Extreme for my suite only that uses the wifi signal from our office building and provides internet to the computers (both wired and wireless) in my suite but have it protected so that other suites in my building can't see my computers.
    It is not possible to configure a single Apple AirPort router in this manner using wireless only, but it would be possible to do this with a single AirPort if you connect your AirPort Extreme to the "main" router using a wired Ethernet connection.
    As for wireless only....you could probably do what you want by using two Apple routers....an AirPort Express to join the wireless network and provide an Ethernet signal to the AirPort Extreme's WAN port. Then the AirPort Extreme could then be configured to provide a separate network using a different subnet.
    Users on the "main" network would not be able to "see" any devices on your "private" network and vice versa.
    I use the two router set up all the time at hotels that only provide a wireless signal. The first Express "joins" the wireless network and feeds an Ethernet signal to the second AirPort which is configured to "create a wireless network" in router mode.
    This way, I can connect multiple devices to my "private" network, but only pay the hotel for one connection since the hotel router only "sees" the AirPort Express that joins the network.

  • How can I set up a wi-fi network, using one time capsule and two airport express

    how can I set up a wi-fi network, using one time capsule and two airport express ?
    The time capsule is near the Mac. ok
    The first Airport is on the corridor, ok, works well and the App on the iPad signals so, ok
    But when I plug the next Airport on another room nearby nothing happens, and signals disconected ....
    is the signal so weak that is not able to go to ono room to the other ?

    Well, even if you have the first express set up to extend the network, the second express can only extend from the TimeCapsule.
    Maybe you got walls of sheetrook in the way, or kitchen/bathroom tiles, etc, dampening the signal rapidly.

  • Cannot extend my network using AirPort Express

    I just purchased a Time Capsule (2TB) and replaced my Airport Express WiFi.  My intention was to expand my network, using the AirPort Express to expand the Time Capsule signal.  I have tried several times and cannot get it to work.
    Using AirPort Utility, I set up the Time Capsule successfully, making certain the "Allow the network to be expanded" box was checked off.
    After resetting my AE, I plugged it in, it was detected by AirPort Utility, and I set the AE to expand the network, using the same network name, security, and password.  When I save the settings and update, the AirPort Uitility returns an error stating that the AE unit could not be located.  AE unit is flashing amber (slowly).
    What DID work was connecting the AE to the Time Capsule with an ethernet cable, but this is not ideal, since I want to locate the AE away from the TC and wish to do it wirelessly.
    Can someone offer some helpful suggestions that will work?
    (Running MacBook Pro w/ OS X 10.7.2 and AirPort Utility 5.5.3.)

    I would suggest the following:
    Please move the AirPort Express (AX) to the same room as the Time Capsule and perform a Factory Default Reset as follows:
    Pull the AX from power
    Wait a few minutes
    Hold in the reset button and continue to hold it in for an additional 8-10 seconds while you simultaneously plug the AX back in to power
    Release the reset button after the hold period, and allow 40-45 seconds for the AX to display a slow, blinking amber light
    Temporarily, connect a spare Ethernet cable from one of the LAN <-> ports on the Time Capsule to your AX
    Open AirPort Utility and click Manual Setup
    Click the Base Station tab below the row of icons to name your AX, assign a device password and adjust Time Zone settings
    Click the Wireless tab next to the Base Station tab and adjust your settings as follows:
    Wireless Mode = Extend a wireless network
    Wireless Nework Name = Same name as your Time Capsule wireless network
    Enter a check mark next to Allow wirelss clients
    Wireless Security = Same setting as your Time Capsule wireless network. You may need to refer to the Time Capsule settings if you are not sure what setting to use
    Wireless Password = Same password as the Time Capsule wireless network
    Confirm Password
    Click Update to save your settings
    Close AirPort Utility and disconnect the Ethernet cable as soon as you see the message that the settings have been stored successfully on the AX
    Wait 40-45 seconds for the AX to restart and display a green light
    You can now locate the AX where it is needed, assuming that it can receive a good wireless signal at its new location
    Post back on your results

  • I have a G5 mac using ver 10.4.11 and a newer mac using ver 10.8.4 these are networked. using the new mac i looked up my my photo on the old mac. It then said you need to upgrade your library which it did. Now the old mac can not open the photos

    I have a G5 mac using ver 10.4.11 and a newer mac using ver 10.8.4 these are networked. using the new mac i looked up my my photo on the old mac. It then said you need to upgrade your library which it did. Now the old mac can not open the photos and say that I need to upgrade my I photo to a newer version. The old mac has no more support from apple in software update so I am not sure where I should go from here. can I use new soft ware with the old mac

    The other part of the upgrade message was a warning that once you upgraded you would no longer be able to open the library with the old version which is exaclty what you did and what happened when you choose to continue
    The iphoto library needs to be upgraded to work with this version of iPhoto. Your photo library will not be readable by previous versions of iphoto after the upgrade. The upgrade process may take several minutes depending on the number of photos in the library. Cancel or upgrade.
    So now your choices are to not use iPhoto with the previous version using it onky with the newer version, restore your backup from before you did this upgrade or purchase iPhoto Library Manager and use it to rebuild the library using the older version of iPhoto (instructions are on their web site) thereby downgrading it (without projects)
    LN

  • HT5022 I'm trying to add a "new client" to my wireless network using Airport Utility, but I can't find that option in the new version.  I've downloaded all available updates of the OS and the utility..  Help!

    I'm trying to add my HP wireless printer as a "new client" to my wireless network using Airport Utility, but I can't find that option in the new version.  I've downloaded all available updates of the OS and the utility..  Help!

    Why would you need to ADD a new Client. Unless the APE sytem is completely different then any other Wireless router the printer should get an IP address from the router. That is IF the printer is setup to get an IP from the LAN DHCP server.
    Now you may want to make that IP it does get a Staticly assign IP address so it never changes, which will screw up printing if it does change. But i don't know if you can do that with APE routers.

  • Can't connect my P1102w printer to my wireless network (using Mac OS 10.6)

    I have a vanilla home wireless network (D-Link to a cable modem), and a MacMini running OS 10.6.8. My Mac laptop and 4th. Gen iPad work seamlessly. But my hours-long attempt to connect my new HP P1102w to the network has been totally frustrating, despite close study of the pdf documentation, the printer's self-test/Device configuration sheet, browsing this forum, watching a slew of YouTube/HP videos, and  following all manner of directions.
    The only consolation is the printer works fine on its USB connection. 
    Here are some issues I've encountered that have stopped me in my tracks:   
    Carefully following both the pdf instructions and HP's online how-to video, I get through Step 6 w/ no problemn. but then I go to Step 7, which says:
    " Under Communication Mode , click Infrastructure , select your network SSID from the Available Network Names (SSID) list, and then click the << button."
    Problem is there's nothing of the kind in that window. All I see is a status of the Wireless: enable or disabled (depending on a choice). And even if I try selecting Enabled, it switches right back to Disabled. Aside: I note the printed instructions show a copyright date of 2011. That's ancient history in the CPU world.  
    Other issues: The only IP address I can find for the printer is the IPv4 address, but that's only for Direct Print Configuration. Is that the IP address I'm looking for?
    The printer's hardward address, I assume, is its MAC ? Boy, I could sure use clearer use of language here. 
    So, needless to add, I'm stuck. It seems it should be THAT hard, but so far nothing I've been able to find on HP support or the forums seems to help. Thanks for any advice you can provide.
    PS. I'd hate to have to return this printer because I'm a two decade HP printer lover, but, alas, I may have to if I can't find a solution.
    Northwest John
    This question was solved.
    View Solution.

    Hi @Northwest-John, 
    I see by your post that you are unable to setup the printer on the wireless network. I can help you.
    Update the printer's firmware by the USB connection just to make sure that isn't causing any issues with the printer's Embedded Web Server (EWS) not allowing the proper changes. HP LaserJet P1102w Firmware Update Utility.
    The newest version is 20130703, which you can compare by printing the configuration page.
    Power cycle the router and restart the Mac.
    The printer won't recognize the network name if there usually is any symbols or spaces in the network name.
    Make sure Safari is set as the default browser. Sometimes the Embedded Web Server (EWS) won't open in other browsers. Open Safari, across the top select the Safari menu, select Preferences, General, set as default.
    Turn the printer off, hold down the wireless button and cancel (x button) while turning the printer back on and don't release the two buttons until the printer stops making noise.
    Print out a configuration report and make sure the SSID and IP address are cleared.
    (hold down the x button and when the printer makes a noise let go)
    Connect the USB cable from the printer to the Mac.
    Go to the Apple, system preferences, print and fax.
    Double click on the P1102w.
    Open the utility.
    Click printer setup.
    Click HTML config.
    This should open the Embedded Web Server for the printer.
    Click the Networking tab.
    Click Wireless from the list on the left.
    (Click Enable if you have this option)
    Under Communication Mode , click Infrastructure.
    Select your network SSID from the Available Network Names (SSID) list and then click the << button so the network name moves over to other box.
    From the Security Mode pop-up menu under Authentication , click WEP, WPA/WPA2 or open . Your selection depends on which Wireless Security Protocol your network uses.
    Make sure you select either hexadecimal or alpha depending on your password. (very important)
    Apply the settings.
    In the confirmation box, (changes have been saved) click OK.
    You should get a solid blue light on the printer shortly.
    Then all we have to do is delete the USB driver and add the network driver.
    Click on the Apple.
    Click system preferences.
    Click the print and fax icon.
    Highlight the printer and click on the - sign to delete the printer. (USB driver)
    Disconnect the USB cable.
    Then click the + sign and select the printer from the list and click add. (P1102w bonjour)
    Test the printer.
    If you have any issues with the HTML config opening then do the following steps:
    Close any applications.
    On the Apple menu bar, click Go, computer, MAC harddrive, Library, Printers, HP, LaserJet, click on folder for your printer, click on EWS browser or HTML config, click the Networking tab, click wireless on the left and fill out your information. (make sure infrastructure is selected) Apply settings.
    Then delete the USB driver and add the network printer.
    Let me know if you are still having issues with filling out the EWS for the printer.
    Have a nice day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • Setting up a home network using the new USB551L modem

    I have recently switched from the 3G USB760 modem to the new 4G LTE USB511L modem. Since I live in a very rural area, it is one of the few internet options that I have and I am forced to use it for my home. I previously set up a wireless network using the previous modem by connecting a wireless router to my computer by ethernet cord. I then went under the properties of the connection in order to allow other computers/devices to use the connection. Since switching to the new USB modem, the network does not appear under the list of options when using the Windows 7 network connections icon in the lower right corner of the screen. I am trying to set up a similar wireless network for my house but I am having difficulty. It seems that everything will connect to the wireless router but the router is lacking internet connection. Any advice is appreciated. 

    Your best Option use th eUSB551L in a Hybrid Router:
    The MBR95 will work for your situation plus it has 4 etherent ports if you need it, you can connect your network/wireless printers, android, ipad, ps3, xbox, nintendo wii, DVR, satellite, etc....
    http://3gstore.com/mbr95
    Combine it with a Full Band 3G/4G Hybrid Antenna and you got the best of all worlds
    http://3gstore.com/product/3047_3g4g-full-band-outdoor-omni-antenna.html

Maybe you are looking for