SG500X 10GE uplink configure switch port access

Hi,
Can I configure the 10GE uplink interface of the SG500X as switcport access?
Partner is asking if a server with 10GE interface can be connected to the 10GE uplink of the SG500X.
Mark J.

I think the speed of the interface does not matter when you want to configure access or trunk. It is always possible whatever speed that interface might be
One thing your customer want to consider is if the compatibility between the module of the server and the switch.

Similar Messages

  • Switch Port Trunk allowed Vlan

    Hi Guys
    Request your help on my query :
    I have a distribution switch  and access switch and port channel between them.
    Dist switch is the VTP server
    lets assum I have 25 vlan
    when I do show vlan brief on the access switch I can see all 25 vlans listed now
    no when I configure switch port trunk allowed vlan (ex : permitting 10 vlans )on the link connecting to access switch at Dist switch
    Dist switch po1 -- connecting to - po Access switch
    Dist switch #
    int po1
    switch port trunk alllowed vlan x,x,x,x,x,x,x,x,x,
    After permitting 10 vlan through trunk allowed vlan and then when I do show vlan brief on the access switch , I should see only the 10 vlan whcih I have permiited right ?
    Thanks in advance  

    Hi,
    John is absolutely correct - even if you do not permit a VLAN on a trunk, it can still provide communication among local ports on a switch that are all assigned to the same VLAN.
    I have a feeling that your original question was focused on a different aspect, though: You probably expected that if you exclude some VLANs from trunks, these VLANs will not be propagated via VTP to surrounding switches. Sadly, this is not the case. The switchport trunk allowed vlan command only affects data traffic in individual VLANs but it has no impact on the operation of VTP protocol. The VTP still advertises all VLANs, regardless of which VLANs are allowed on a trunk. To put it plainly, in a VTP domain, all server/client switches will know about all VLANs. THere is no legal possibility of having a single VTP domain consisting of server/client switch and yet have the switches differ in their VLAN database contents. It's as easy as that: one VTP domain = one big common VLAN database.
    Best regards,
    Peter

  • Port Access mode allow tagged frames ?

    Hello,
    From my understanding Cisco Catalyst switch port access mode only allow untagged frames to be received and proceeded. Tagged frames received on access mode port should be discarded.
    But I have found in BCMSN course Student Guide following phrase
    If a non-802.1Q-enabled device or an access port receives an 802.1Q frame, the tag data is
    ignored, and the packet is switched at Layer 2 as a standard Ethernet frame.
    Is in this case term access related to non Cisco equipment ? Or where are some Cisco Catalysts HW/SW combinations in which access mode port accept also tagged frames ?
    With Best Regards
    Tomas

    Hello Tomas,
    802.1Q tagged frames with a vlan-id = access vlan of the port are accepted on Cisco Catalysts.
    for Sure it was in 2004-2005 when I did L2 security tests and read about the following:
    This is the basis for one of the L2 security attack that is called vlan hopping:
    if you send a frame with two 802.1Q tags and:
    a) the external tag vlan-id = port access vlan
    b) the same vlan is used as native vlan in a inter-switch trunk
    the attacker can send a frame from vlan X to vlan y bypassing L3 security and routing devices.
    the recommendation is to use as native vlan a dedicated vlan for all trunks that is never used on access ports.
    Hope to help
    Giuseppe

  • LMS 4.2 - How do I find switch ports that are configured as trunks.

    I've been tasked with finding all switch ports that are configured as Trunks. We plan to use LMS 4.2 to push (via Netconfig) new interface level commands to all user (non-trunked) ports. From my experience, this poses a problem because we do not know which ports are configured as trunks -vs- user ports.
    Using Netconfig is not going to be easy since there is no way to script this. It would be great if I could run a show command on a switch and then have CWSI peform a change based upon the output.
    In other words, we need a way to run a job based upon the output of a command.
    Is there a section of LMS that I could use for help with this?
    Thanks,

    You need to go to Monitoring>Dashboard. Here Just click the switch in the Llisted device and then click the interface you will find the all the down and Up interface with type of configuration (i.e. Trunk or Access.)

  • AP-1131AG: 2 VLANs/SSIDs, switch port configuration?

    We're setting up a (seemingly) simple deployment of some APs, and want 2 SSIDs...one will have Pre-Shared WEP and one will be open and broadcast (with access-lists on the router). My question is how to set up the switch port to match my AP, in order for it to pass both VLANs (in this case I've setup WLAN100=VLAN100 and WLAN101=VLAN101)...Do I have to configure trunking on that switchport? Thanks for any links or answers on this!!!

    Hi Vince,
    Here is a great doc that goes over this concept in detail. You will need to configure Trunking on the switchport. Have a look at what yours might look like;
    switchport mode trunk
    switchport trunk encapsulation dot1q
    switchport trunk native vlan 1
    switchport trunk allowed vlan 1,100,101
    From this excellent doc;
    Using VLANs with Cisco Aironet Wireless Equipment
    http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801d0815.shtml#clic2935xl
    Hope this helps!
    Rob

  • CONFIGURE VOICE DATA ACCESS PORT SW SF500-48

    Hi Everybody,
    I have a SW SF500 small business and i need configure one port how access for Voice and data VLan. I need help with any configuration that can apply por this requirement. I attach the design that i hope to work
    Thanks in advance

    Here is a link to a detailed document on configuring auto voice vlan:
    http://sbkb.cisco.com/CiscoSB/ukp.aspx?vw=1&docid=14906e97e0c24e14836144529c214b87_Voice_VLAN_Properties_on_Sx500_Series_Managed_Switches.xml&pid=2&respid=0&snid=4&dispid=0&cpage=search
    Here is a link to the admin guide(p252):
    http://www.cisco.com/en/US/docs/switches/lan/csbms/Sx500/administration_guide/500_Series_Admin_Guide.pdf

  • Myself is Anish and am facing some issues in configuring sg30052 port gi switch

    Hai help me on this..
    User requirements
    1) Switch is configured with a management ip 172.16.7.x   
    2) Two VLAN's has tobe created 114 & 115
    3) Configure the switch-ports as access ports and has to be assigned with one of the two vlans as user requirement.
    4) Two ports of the switch has to be configured as trunk port.
    5) Port security has to be enabled in all access ports.

    Hi Anish-
    1 - Log in to the console of the switch
    config t
    interface vlan 1
    ip address 172.16.7.x
    2-
    config t
    vlan database
    vlan 114, 115
    3-
    config t
    int gi01
    switchport mode access
    switchport access vlan 114
    int gi02
    switchport mode access
    switchport access vlan 115
    4-
    config t
    int gi48
    switchport mode trunk
    switchport trunk allowed vlan add 114, 115
    5-
    https://supportforums.cisco.com/docs/DOC-27753
    https://supportforums.cisco.com/docs/DOC-27720
    -Tom
    Please mark answered for helpful posts

  • Switch port configuration for 3500i AP

    Hi,
    We are due to install a brand new enterprise WLAN based on the WiSM2 platform, 3502i AP and WCS. The APs will be plugged into the 2960S-24TPS-L.
    I have scanned over all documentation and cannot for the life of me find a recommended switch port configuration for connecting the AP to the switch in terms of speed / duplex etc. For example, should I just configure the port to auto detect, or is forcing the speed / duplex the way to go. I could also do with knowing other best practice configurations for AP connectivity.
    Any help would be greatly appreciated.
    Chris.

    The AP comes online with just auto detect, but I want to know if there are any benefits to forcing this to 1Gbps / Full duplex, or even if this is the right way to go. I suspect auto detect is the best method.

  • Tandberg C20 switch port configuration

    Is there a recommended switch port setting (3750x) for connecting a Tandberg C-Series (20,40,60)?
    Smartports?
    Port-Security?
    Access-port only?

    The AP comes online with just auto detect, but I want to know if there are any benefits to forcing this to 1Gbps / Full duplex, or even if this is the right way to go. I suspect auto detect is the best method.

  • ESX/VMWare Switch Port Configuration

    Does anyone know how to configure a 3560 switch port that is connecting to an ESX host with multiple VM's??

    Hi Jason,
    Most of the time people will configure the port as a trunk to the ESX host.  So on the 3560 you can just do:
    switchport trunk encap dot1q
    switchport mode trunk
    This will allow your VMs to be in different vlans if you would like.
    Chad Peterson
    CCIE 23213
    Network Consulting Engineer
    .:|:.:|:.
      CISCO
    PDI Data Center
    http://www.cisco.com/go/pdihelpdesk

  • Is it possible to configure the switch port to mode trunk if I m going to put a Pc on that port?

    If the answer is yes then what are the adventages and the disadventages of doing this. I've proof this with real switches and configuring the ports as trunk with a pc and the pc can ping other pc that are on the same Vlan or configure as trunk. I would like to know why does that happend?

    Hi,
    It may work, you can configure an interface connecting to host as a trunk link but only if you want that host to receive data from multiple vlans since trunks allowed all vlans per default.
    Usually, on a switch you configure vlans to logically devide the users and to avoid flooding all the users with all the information from multiple vlans which they do not need and which causes unnecessary burden on the ports carrying traffic.
    Hope this helps.

  • How to get Networking Switch Port Configuration (I guess SNMP4j will help)

    Greetings :)
    We have extreme Summit 450e switches installed in our organization. approximately 2000 desktops are connected to these switches.
    Now, I want to make a utility to get info from these switches, for example, which IP, MAC etc is running on a particular switch port. I want to extract these kind of info from all switches and export it into a database.
    Any help, how to start this work.
    Thanks...

    > Any help, how to start this work.
    First research what programmable interfaces it supports.  That includes any management API including SNMP, TCP and HTTP.
    And then from that figure out what you want to do with it.
    After you do both of the above then you start looking to java to program the solution.

  • How-do-i-configure-guest-wifi-access-using-2504-wlc-fortigate-utm-l3-device

    Dear All
    I have a 2504 Wireless Controller with multiple radios attached. I currently have a "private" WLAN configured (taking ip from windows server based DHCP of Range 192.1681.0/24 ) and working, but I need to add a Guest/Public WLAN which should take the IP from Other DHCP Configured on Fortigate UTM of range 172.16.0.0/24.
    We have one SG300 switch in the office and the rest are basic switches.
    Our firewall/router is a Fortigate UTM 240D
    Find the attached network diagram for the issue.
    Is there a SIMPLE way to enabling guest access that doesn't require VLANS (or are VLANS easier than I'm making them)? 
    Thanks.
    - See more at: https://supportforums.cisco.com/discussion/12473186/how-do-i-configure-guest-wifi-access-using-2504-wlc-fortigate-utm-l3-device#sthash.aj1XcWI0.dpuf

    Complete these steps in order to configure the devices for this network setup:
    http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-vlan/70937-guest-internal-wlan.html
    Configure Dynamic Interfaces on the WLC for the Guest and Internal Users
    Create WLANs for the Guest and Internal Users
    Configure the Layer 2 Switch Port that Connects to the WLC as Trunk Port

  • Switch port in dot1x multi-auth mode stops passing traffic

    Dear All,
    I am experiencing a problem on a Catalyst 4510 (cat4500-ipbasek9-mz.122-53.SG.bin) with 802.1x configured. Client PCs are connected via a mini desktop switch to a Cat 4510 switched port in multi-auth mode. The configuration of the port follows:
    interface GigabitEthernet2/34
    switchport mode access
    ip arp inspection limit rate 30
    authentication host-mode multi-auth
    authentication port-control auto
    authentication periodic
    authentication timer reauthenticate server
    dot1x pae authenticator
    dot1x timeout tx-period 5
    dot1x max-reauth-req 6
    spanning-tree portfast
    ip verify source vlan dhcp-snooping
    end
    It happens from time to time that the Cat 4510 port stops passing traffic. Reconnecting the mini switch recovers the communication. Client PCs connected to the mini switch seem to be authorized at the moment when the problem occures. The RADIUS Termination-Action attribute is set to RADIUS-Request. The problem is not present if "authentication periodic" is disabled.
    Did anyone experience a simmilar problem? Any advice?
    Thanks.
    Mirek

    We have the same issue on 3750E switch running 12.2.(58)SE

  • 802.1X Authentication issues when moving between switch ports

    Hi Guys,
    We are having some issues at our office where when users move from one switch to another, the 802.1X authentication does not want to take place. The PC just gets an APIPA address. Now I have read about features that MAC Move and MAC replace but they seem to be used when moving from one port a switch to another port on that same switch. Will MAC move help for issues between switches? And should I focus my attention on the switch's configuration or have a look at the NPS server that might be blocking that authentication as the user is already authenticated?
    My configuration we have on the switch ports look as follows:
    authentication host-mode multi-domain
    authentication order dot1x mab
    authentication priority dot1x mab
    authentication port-control auto
    dot1x pae authenticator
    Your help is greatly appreciated.
    Grant

    Hi Neno,
    Thanks for the reply. We are using NPS on a Server 2008 R2 virtual machine. The switches are stacked 2960S-48FPS-L running 15.0(2)SE. I will quickly do the debugs and get back to you.
    Here is the config:
    aaa group server radius customer-nps
     server name radius1
     server name radius2
    aaa authentication dot1x default group radius
    dot1x system-auth-control
    radius server radius1
     address ipv4 172.28.130.52 auth-port 1645 acct-port 1646
     key 7 05392415365959251C283630083D2F0B3B2E22253A
    radius server radius2
     address ipv4 172.28.131.52 auth-port 1645 acct-port 1646
     key 7 107C2B031202052709290B092719181432190D000C
    interface GigabitEthernet1/0/1
     switchport access vlan 300
     switchport mode access
     switchport voice vlan 2
     srr-queue bandwidth share 1 30 35 5
     queue-set 2
     priority-queue out
     authentication host-mode multi-domain
     authentication order dot1x mab
     authentication priority dot1x mab
     authentication periodic
     authentication timer reauthenticate 28800
     authentication timer inactivity 1800
     mab
     no snmp trap link-status
     mls qos trust cos
     dot1x pae authenticator
     auto qos trust cos
     storm-control broadcast level 1.00
     storm-control multicast level 1.00
     spanning-tree portfast
     spanning-tree bpdufilter enable

Maybe you are looking for

  • Junk chars in the file posted on application server

    HI All, I am posting a file on the application server using the OPEN DATASET, TRANSFER, CLOSE DATASET commands. The file is posted successfully but it contains junk characters like # and some box kind of character. The file that has the data doesnot

  • Formula as Parameter

    I have Crystal Reports X1, Pack 2. I have an inventory forecasting report with 2 subreports. I have set up the report with parameters as the user likes to view the report for a specific brand or item category. The report Item     Brand     Net Stock 

  • IDVD will not encode audio

    Hi, Just as the topic says, iDVD will not encode the audio......well whats happening is that it says its in the process of encoding....the bar turns grey, and has the loading color wheel thing and thats basically whats happening. Its been doing this

  • Mate Framework compiler errors

    I can get the Mate Framework to compile under the Flex 4 beta 1 SDK with minor changes. However if I use the latest nightly Flex 4 SDK (full Adobe version), I get the following compiler errors that I can't seem to figure out why I'm getting: - 1017:

  • EP implementation for Internet users

    Hello, I need to Implement EP for internet and intranet users, in which for internet users I need to fetch the summary data of R/3 applications. how shall we proceed with the implmentation of portal for internet users, pls suggest some blogs showing