Sge2000 just doesn't route in a sane manner

I have 3 vlans on a standalone SGE2000 in Layer 3 mode. VLAN 1 for servers, VLAN2 for workstation and VLAN100 for management. All the servers in VLAN1 can see and talk to one another. Router for internet is also connected to VLAN1. All servers have internet access like expected.
I only have a single machine in the Workstation VLAN for testing right now. It can access some of the servers but not all. It can also access the internet properly, but certain servers it just won't talk to.
Now this is the weird part. If I move the workstation over to the management VLAN and change it's IP address accordingly, it will begin to talk to the other servers it would not talk to before. But then it won't talk to the internet router which is in the same VLAN as the servers.
The servers it can't access though are using other advanced features or unique scenarios. One is a file server with 4 ports aggregated with LACP. The LAG group is in the proper VLAN and the other servers can access this so I'm pretty sure that is all built properly.
The other servers it can't access are VM's on ESX 3.5. There is no VLAN tagging going on in the ESX server. All VM's attach to the same interface on the physical server and are in the same subnet as the management IP of the ESX server. My test workstation in the other VLAN can load the web management for the ESX server, but can't contact any of the VM's. Again, these VM's are in the same subnet and bound to the same interface as the Web management that can be accessed.
Without changing any other port configurations, if I move the workstation to the same VLAN as the servers, it can access everything without issue.
It would seem that's there's some sort of bugginess in the way the switch selectively routes for certain IP's and certain VLANS.
I have no ACLS in place, all ports in all VLANS are set to access mode. None of the machines have software firewalls. The switch itself can ping all machines in question in all VLANS. All machines use their respective switch vlan interface IP as their default gateway. Switch has default route pointed at router in VLAN1.
I'm pretty convinced at this point that the firmware in the switch is buggy.
If no one has any ideas, my next step is to start sniffing traffic destined for the port of the ESX server and see if packets from the workstation arrive there at all. That's the closest way I can figure to determine if the switch is even trying to forward packets from the other VLAN to the VM's.
If that doesn't reveal anything, my only resort appears to be to sell my wife's car and buy a Cisco.

Kinda weird problem you got there. Have you tried re-flashing the firmware?

Similar Messages

I've just changed my router and whilst my laptops sync ok, my G4 tower which connects via an airport express doesn't connect to the internet. I think it's something to do with the IP or DHCP settings but have had no success, any help much appreciated.

I've just changed my router and whilst my laptops sync ok, my G4 tower which connects via an airport express doesn't connect to the internet. I think it's something to do with the IP or DHCP settings but have had no success, any help much appreciated.

Hi Jake,
Is it connecting to the Router or Modem?
Is the new Router using maybe WPA2 encryption? If so, G4s can only do WPA or less.
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
old... http://docs.info.apple.com/article.html?artnum=106653
Hi, this has worked for a few...
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
The Interface that connects to the Internet, needs to be drug to the top of System Preferences>Network>Show:>Network Port Configurations and checked ON.
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
Then... Try putting these numbers in Network>Airport>TCP/IP>DNS Servers, for the Interface you connect with...
208.67.222.222
208.67.220.220
Then Apply.
Also, turn off IPv6:
System Preferences » Network » AirPort » TCP/IP tab » Configure IPv6

L2TP on Cisco ASA 5505, just doesn't work??!

This is pretty urgent, client expects me to have this up by lunch today
So, there is this Cisco ASA 5505 ver 8.4.
Most things work but now I want to setup a vpn connection...
I have done this 2 ways, first by using the "VPN Wizard" in ASDM and then 5 hours later removing everything and configuring from cli.
And it just doesn't work, client (WinXP & Win7) gets "error 792" and sometimes "error 789" (both indicating problem with phase 1, I'm pretty sure of that)
Googling on those gives a few suggestions none works.
All I get in the log on Cisco is the "Error processing payload: Payload ID: 1"
Googling on that only comes up with a few pages telling me this message is caused by an error. (Yeah, I could never have guessed...)
For the cli config, I followed this tutorial carefully (3 times actually...)
http://www.cisco.com/en/US/docs/secu...html#wp1117464
I'm using PSK for IPSec, entered same on Cisco and client - checked several times, this is not a password/PSK issue.
Ports opened on Cisco: 500, 1701, 4500
(For a try I opened all ports, no change.)
And here's the "show run":
Code:
ASA Version 8.4(2)
hostname ciscoasa
enable password <string> encrypted
passwd <string> encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
switchport access vlan 7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.5.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address #.#.#.# 255.255.255.252
interface Vlan7
description VLAN till kontor
no forward interface Vlan2
nameif kontor
security-level 100
ip address 172.16.5.1 255.255.255.0
ftp mode passive
clock timezone GMT 0
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Webserver
host 192.168.5.2
object network Webserver443
host 192.168.5.2
object network rdp
host 192.168.5.2
object network vpnserver
host 192.168.5.2
object service vpn-service-group
object network VPN
host 192.168.5.2
object-group service Webports tcp-udp
description Portar fÃ¶r webbserver
port-object eq 443
port-object eq www
object-group service DM_INLINE_TCP_1 tcp
group-object Webports
port-object eq www
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group service VPNports tcp-udp
port-object eq 1701
port-object eq 4500
port-object eq 500
object-group service RDP tcp-udp
port-object eq 3389
object-group service vpn-services tcp-udp
port-object eq 1701
port-object eq 500
access-list outside_access_in extended permit tcp any object Webserver eq www
access-list outside_access_in_1 extended permit tcp any object Webserver object-group DM_INLINE_TCP_1
access-list outside_access_in_1 remark Ãppnar fÃ¶r vpn
access-list outside_access_in_1 extended permit object-group TCPUDP any any object-group VPNports
access-list outside_access_in_1 extended permit object-group TCPUDP any any object-group RDP
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu kontor 1500
ip local pool vpn1 10.10.10.10-10.10.10.50 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
object network obj_any
nat (inside,outside) dynamic interface
object network Webserver
nat (inside,outside) static interface service tcp www www
object network Webserver443
nat (inside,outside) static interface service tcp https https
object network rdp
nat (inside,outside) static interface service tcp 3389 3389
access-group outside_access_in_1 in interface outside
route outside 0.0.0.0 0.0.0.0 79.142.243.33 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
aaa authorization command LOCAL
aaa authorization exec LOCAL
http server enable
http 0.0.0.0 0.0.0.0 inside
http 0.0.0.0 0.0.0.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA mode transport
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev2 ipsec-proposal 3DES-SHA
protocol esp encryption aes-256 aes-192 aes 3des
protocol esp integrity sha-1 md5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal 3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ca trustpoint ASDM_TrustPoint0
enrollment self
subject-name CN=ciscoasa
proxy-ldc-issuer
crl configure
crypto ca certificate chain ASDM_TrustPoint0
.... (sorry, not giving you the cert...)
crypto ikev2 policy 1
encryption 3des
integrity sha
group 2 1
prf sha
lifetime seconds 86400
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash md5
group 1
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 1
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 1
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 1
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh scopy enable
ssh 0.0.0.0 0.0.0.0 inside
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 10
console timeout 0
no vpn-addr-assign aaa
no vpn-addr-assign dhcp
l2tp tunnel hello 100
dhcpd dns 8.8.8.8
dhcpd auto_config outside
dhcpd address 192.168.5.11-192.168.5.36 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec
address-pools value vpn1
group-policy DfltGrpPolicy attributes
dns-server value 79.142.240.10
vpn-tunnel-protocol l2tp-ipsec
address-pools value vpn1
username test password <string> nt-encrypted
username someoneelse password <string> nt-encrypted privilege 15
username someoneelse attributes
vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec
service-type admin
username someone password <string> nt-encrypted privilege 0
tunnel-group DefaultRAGroup general-attributes
authorization-server-group LOCAL
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
tunnel-group vpn1 type remote-access
tunnel-group vpn1 ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
privilege cmd level 3 mode exec command perfmon
privilege cmd level 3 mode exec command ping
privilege cmd level 3 mode exec command who
privilege cmd level 3 mode exec command logging
privilege cmd level 3 mode exec command failover
privilege cmd level 3 mode exec command packet-tracer
privilege show level 5 mode exec command import
privilege show level 5 mode exec command running-config
privilege show level 3 mode exec command reload
privilege show level 3 mode exec command mode
privilege show level 3 mode exec command firewall
privilege show level 3 mode exec command asp
privilege show level 3 mode exec command cpu
privilege show level 3 mode exec command interface
privilege show level 3 mode exec command clock
privilege show level 3 mode exec command dns-hosts
privilege show level 3 mode exec command access-list
privilege show level 3 mode exec command logging
privilege show level 3 mode exec command vlan
privilege show level 3 mode exec command ip
privilege show level 3 mode exec command ipv6
privilege show level 3 mode exec command failover
privilege show level 3 mode exec command asdm
privilege show level 3 mode exec command arp
privilege show level 3 mode exec command route
privilege show level 3 mode exec command ospf
privilege show level 3 mode exec command aaa-server
privilege show level 3 mode exec command aaa
privilege show level 3 mode exec command eigrp
privilege show level 3 mode exec command crypto
privilege show level 3 mode exec command ssh
privilege show level 3 mode exec command vpn-sessiondb
privilege show level 3 mode exec command vpnclient
privilege show level 3 mode exec command vpn
privilege show level 3 mode exec command dhcpd
privilege show level 3 mode exec command blocks
privilege show level 3 mode exec command wccp
privilege show level 3 mode exec command dynamic-filter
privilege show level 3 mode exec command webvpn
privilege show level 3 mode exec command module
privilege show level 3 mode exec command uauth
privilege show level 3 mode exec command compression
privilege show level 3 mode configure command interface
privilege show level 3 mode configure command clock
privilege show level 3 mode configure command access-list
privilege show level 3 mode configure command logging
privilege show level 3 mode configure command ip
privilege show level 3 mode configure command failover
privilege show level 5 mode configure command asdm
privilege show level 3 mode configure command arp
privilege show level 3 mode configure command route
privilege show level 3 mode configure command aaa-server
privilege show level 3 mode configure command aaa
privilege show level 3 mode configure command crypto
privilege show level 3 mode configure command ssh
privilege show level 3 mode configure command dhcpd
privilege show level 5 mode configure command privilege
privilege clear level 3 mode exec command dns-hosts
privilege clear level 3 mode exec command logging
privilege clear level 3 mode exec command arp
privilege clear level 3 mode exec command aaa-server
privilege clear level 3 mode exec command crypto
privilege clear level 3 mode exec command dynamic-filter
privilege cmd level 3 mode configure command failover
privilege clear level 3 mode configure command logging
privilege clear level 3 mode configure command arp
privilege clear level 3 mode configure command crypto
privilege clear level 3 mode configure command aaa-server
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:dd92aa6707dc63e8ed7dad47cfecdd47
: end
In Pingvino Veritas!

I lmost got it working now, new problem is that the connection is immediately ended.
Logs shows that client is authenticated and assigned an ip.
From the logs, all happens during one second:
IPAA: Client assigned ip-address from local pool
IPAA: Local pool request succeeded for tunnel-group
IPAA: Freeing local pool address
L2TP Tunnel created, tunnel_id is 24
L2TP Tunnel deleted, tunnel_id =24
IPSEC: An outbound remote access SA has been deleted
IPSEC: An inbound remote access SA has been deleted
Session is being torn down. Reason: L2TP initiated
Teardown UDP connection

AMD / CPA on ICM 6 just doesn't work, HELP!!

We're running IPCCE 6 (with IP IVR QMANAGER) with Outbound Option configured with 10 ports. Our calls go out via PRIs.
We have several IVR outbound campaigns (Transfer to IVR Campaign = checked
Enable IP AMD = checked
Transfer to IVR Route Point = checked
Terminate Tone detect = checked
TDM Fast Voice Detect = checked )
and our dialer just doesn't know when is an answering machine picking up.
I've tested it by calling into an analog line I have in the office hooked up to an answering machine and success rate was 20%.
Are there any registry settings I can tweak to improve it?

There are Call Progress Analysis settings in 7.0 and they are described in the Outbound User Guide for 7.0 on page 3-15. It mentions that silence supression must not be engaged, so the dial peers should have "no vad". Then look at the table 3-1 for CPAJitterBufferDelay, CPAActiveThreshold, CPAAnalysisPeriod etc.
I am not sure what's in 6.0 so you would have to check.
Regards,
Geoff

Cannot connect to Net, have done for last 12 months no problem, I have other apple products that are connecting to the same hub happily. The hub is seen and the signal is strong, it just doesn't connect. I have reset the network settings with no joy.

cannot connect to Net, have done for last 12 months no problem, I have other apple products that are connecting to the same hub happily. The hub is seen and the signal is strong, it just doesn't connect. I have reset the network settings with no joy. Any help much appreciated?

Try restarting your WiFi router by removing power to it for 30 seconds.

I just want the router I have been promised?

On (or around) the 9th July my Homehub router stopped giving me broadband.
I tried all the tests on the BT website, but that green light just wouldn't come on. I called on support 11th July who did a line check then told me they would send me a replacement router within 48 hours. 72 hours later I called back to get an update, only to find no such order for a replacement had been raised!
The Agent order me a new one there and then. When that hadn't arrived (21st July) I called again to get an update, to find that the Homehub order was "pending". The Agent repeated that that they would send me a new router, and it would be with me on Monday 25th July.
I haven't recieved it, and don't want to speak to another agent who has to apologise profusely and then order something that just doesn't turn up. I am so very very frustrated, that I can't speak to someone who can resolve my problem.
To add insult to injury my original case has been marked as "resolved" - argh!
Can someone please tell / advise me on how to get this issue sorted out? I will not call and agent again, they don't do anything. Why can't BT sort this out?
Can anyone offer help?
D.

It can be delivered at any time up to 6pm on the day of due delivery your other alternative is to contact the forum mods via this link and get them to look into it for you
http://bt.custhelp.com/app/contact_email/c/4951
they normally reply within 72 hours directly to you by email or phone
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

How do I fix a initializing problem with my macbook pro? I only get to the blank screen with the apple logo and the "processing something"sign... it just doesn't start the system....

How do I fix a initializing problem with my macbook pro? I only get to the blank screen with the apple logo and the "processing something" sign... it just doesn't start the system....
Please help
Marcelo

If there is no loading bar, it's usually a problem with a third party kext file in OS X itself.
You can press the power button down to force a hardware shutdown, then reboot holding the shift key down on a wired or built in keyboard, this will disable them and you go around and update your third party software.
Gray, Blue or White screen at boot, w/spinner/progress bar
Also take this time to backup your users files off the machine if possible.
Most commonly used backup methods
Sometime that won't work and you need to do more
..Step by Step to fix your Mac

Time Machine Just Doesn't Work Anymore

I was a happy Time Machine (with Time Capsule) user for months. But it just doesn't work anymore. It takes longer than an hour to do every hourly backup so it is backing up 24 hours a day. It finds hundreds of thousands of files changed every hour and tries to back them up. Finders says only tens of files have been modified all of today. I have tried rebuilding my spotlight indexes, repairing my Time Capsule with Disk Utility and starting over with a brand new backup. But it just backs up hundreds of thousands of files every hour. So I am turning off Time capsule since it is clearly broken. If anyone has any suggestions at all I would welcome them.

Marcia,
Consider the following, it might give you some ideas:
Time Machine performs backups at the file level. If a single bit in a large file is changed, the WHOLE file is backed up again. This is a problem for programs that save data to monolithic virtual disk files that are modified frequently. These include Parallels, VMware Fusion, Aperture vaults, or the databases that Entourage and Thunderbird create. These should be excluded from backup using the Time Machine Preference Exclusion list. You will, however, need to backup these files manually to another external disk.
One poster observed regarding Photoshop: “If you find yourself working with large files, you may discover that TM is suddenly backing up your scratch disk's temp files. This is useless, find out how to exclude these (I'm not actually sure here). Alternatively, turn off TM whilst you work in Photoshop.” (http://discussions.apple.com/thread.jspa?threadID=1209412)
If you do a lot of movie editing, unless these files are excluded, expect Time Machine to treat revised versions of a single movie as entirely new files.
If you frequently download software or video files that you only expect to keep for a short time, consider excluding the folder these are stored in from Time Machine backups.
If you have recently created a new disk image or burned a DVD, Time Machine will target these files for backup unless they are deleted or excluded from backup.
Installing new software, upgrading existing software, or updating Mac OS X system software can created major changes in the structure of your directories. Time Machine will backup every file that has changed since the installation.
Files or folders that are simply moved or renamed are counted as NEW files or folders. If you rename any file or folder, Time Machine will back up the ENTIRE file or folder again no matter how big or small it is.
George Schreyer describes this behavior: “If you should want to do some massive rearrangement of your disk, Time Machine will interpret the rearranged files as new files and back them up again in their new locations. Just renaming a folder will cause this to happen. This is OK if you've got lots of room on your backup disk. Eventually, Time Machine will thin those backups and the space consumed will be recovered. However, if you really want recover the space in the backup volume immediately, you can. To do this, bring a Finder window to the front and then click the Time Machine icon on the dock. This will activate the Time Machine user interface. Navigate back in time to where the old stuff exists and select it. Then pull down the "action" menu (the gear thing) and select "delete all backups" and the older stuff vanishes.” (http://www.girr.org/mac_stuff/backups.html)
*TechTool Pro Directory Protection*
This disk utility feature creates backup copies of your system directories. Obviously these directories are changing all the time. So, depending on how it is configured, these backup files will be changing as well which is interpreted by Time Machine as new data to backup. Excluding the folder these backups are stored in will eliminate this effect.
*Backups WAY Too Large*
If an initial full backup or subsequent incremental backup is tens or hundreds of Gigs larger than expected, check to see that all unwanted external hard disks are still excluded from Time Machine backups.
This includes the Time Machine backup drive ITSELF. Normally, Time Machine is set to exclude itself by default. But on rare occasions it can forget. When your backup begins, Time Machine mounts the backup on your desktop. (For Time Capsule users it appears as a white drive icon labeled something like “Backup of (your computer)”.) If, while it is mounted, it does not show up in the Time Machine Prefs “Do not back up” list, then Time Machine will attempt to back ITSELF up. If it is not listed while the drive is mounted, then you need to add it to the list.
*FileVault / Boot Camp / iDisk Syncing*
Note: Leopard has changed the way it deals with FileVault disk images, so it is not necessary to exclude your Home folder if you have FileVault activated. Additionally, Time Machine ignores Boot Camp partitions as the manner in which they are formatted is incompatible. Finally, if you have your iDisk Synced to your desktop, it is not necessary to exclude the disk image file it creates as that has been changed to a sparsebundle as well in Leopard.
Let us know if any of this helps.
Cheers!

It just doesn't work and help is needed, hence why I'm on a Forum? Brownie points for whoever can help on this one...

So. As always, it's about iTunes - as Apple is the most inconvenient corporation ever founded. Anyway! I've had this problem for about 6 months and haven't bothered to ask anyone. I've restored the computer numerous times and tried to fix the issue with help from other nonsensical forums. The problem is that 'apple mobile device service' is eating up a large amount of CPU, and therefore tends to make the computer run like a log. I have uninstalled it before but then iTunes won't recognize my iPod - funnily enough. As well as this, iTunes won't connect to the store? However, it doesn't say it's not, it just doesn't load. It states that it is 'accessing iTunes store', but it's not. I'm running all of this on a windows 7 Acer extensa 5235 - just in case that helps. It probably won't, but you guys are clever, right? I mean, I could probably ask you to peel an orange for me, and you'd do it without even physically touching it. Just with the power of your omnipotent minds. Anyway yeah, if anyone can help on this one, would be much appreciated.

Wow what a rambling mess and complete waste of time.
Did you try a search of the forums for similar issues? Doing so would have revealed multiple similar issues with valid troubleshooting, saved you time, and saved those that have read that crap from being subject to your rambling psychosis.
FYI, in the future, get to the point and cut the crap when asking for help.
Oh, completely uninstall iTunes and reinstall the current version of iTunes.

HT1689 I subscribe to my video podcasts but some of them either has a small red E next to them and won't download new content or some just doesn't download new content. I have been watching the Rachael Maddow video podcast for at least a month with no pro

I subscribe to my video podcasts but some of them either has a small red E next to them and won't download new content or some just doesn't download new content. I have been watching the Rachael Maddow video podcast for at least a month with no problems. Now suddenly it won't download the last nights show. I have read and followed all troubleshoot and cannot find a solution. I have unsubscribed and re-subscribed to no avail. Can someone help me with this problem?

keian27 wrote:
And now that my contract has expired, I have some options. Last weekend, I called Verizon again threatening to leave. The representative offered the same $75 rebate that was offered to me 6 months earlier. I even offered up one of my device upgrades in place of a network extender, but that deal was knocked down. And so now I’m left with the option to make a public spectacle out of this scenario and hope Verizon takes notice. Failing that, I’ll be forced to leave Verizon behind.
I don't understand. If having service in your home IS important to you and you already know Verizon's policy, why have you not instead started to search for carriers which cover your home? It seems a pretty easy decision to me, at least.

Hi, can I move my iTunes library to an external hardrive without having to consolidate it as my prehistoric computer just doesn't have the space even though I have deleted everything possible to make room? Please help :(

Hi, can I move my iTunes library to an external drive without having to consolidate it as my prehistoric computer just doesn't have enough space even though I have deleted everything possible to make room? Please help

Hi, do you know if this works if I then want to move my library to a new computer as that is my main intention bacause my old computer hasn't got enough space for me to add new albums so I want to ditch the computer (its got to be about 100 years old and doesn't seem to cope well with modern technology!!) and start using my laptop for my iTunes. I am at the point now where i'm ready to throw both my computer and iPod out the window!!!! I might point out as well that in trying to clear space on my computer I accidently deleted the Bonjour programme which is aparently needed to use the home share option, oops!!!!
Thanks, Kerry

Is there a way to fix an iPod touch 4G home button that isn't stuck but just doesn't work?

A couple weeks ago my home button got stuck. To fix it I found this video http://www.youtube.com/watch?v=yBfhCmq9VkA&list=WL429346A18D0B1E65 to help me out. The second option of using the charger ended up working, thus making the button work again. It was working fine after doing that but then it got stuck down again and I had to put the charger in and do that again. However, all of a sudden the home button just doesn't work anymore. It's not even stuck all the way down. I can press it repeatedly but still nothing.
I've had the iPod for about 6 months now and got it off of amazon refurbished so warranty is out of the question i'm sure. If it really is broken with no way to fix it then that's fine as i've been using assitive touch for weeks now and am used to it since i've been using it egulary since there's no other way. I just wanted to ask and make sure first before anything else though.

Try:
http://snapguide.com/guides/calibrate-your-home-button/?utm_expid=69945963-15
fix for Home button
iPhone Home Button Not Working or Unresponsive? Try This Fix
- If you have iOS 5 and later you can turn on Assistive Touch it add the Home and other buttons to the iPods screen. Settings>General>Accessibility>Assistive Touch
- If not under warranty Apple will exchange your iPod for a refurbished one for:
Apple - Support - iPod - Repair pricing
You can do it an an Apple store by:
Apple Retail Store - Genius Bar
or sent it in to Apple. See:
Apple - Support - iPod - Service FAQ
- There are third-party places like the following that will repair the Home button. Google for more.
iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens

I have purchased the Acrobat pro subscription for 1 year and have followed the steps to install it. But when i go to start it, It crashes and it does this every time! I have restarted my mac pro and also restarted in safe mode but it just doesn't work! PL

I have purchased the Acrobat pro subscription for 1 year and have followed the steps to install it. But when i go to start it, It crashes and it does this every time! I have restarted my mac pro and also restarted in safe mode but it just doesn't work! PLEASE HELP!!

Hi jim1287,po
Check for the latest updates. Installing latest updates should resolve this problem.
Also, try to ran disk repair using safe mode in Mac, for instructions please visit: http://support.apple.com/kb/PH14204
Try enabling root user profile on mac and try to check. OS X Mavericks: Enable and disable the root user
Regards,
Ajlan Huda.

My Apple TV Gen 1 just doesn't work

Hello,
I have setup/reset/setup this device so many times it just drives me crazy. I honestly believe that this technology just doesn't work.
I have an iMac running the most up to date version of OS X 10.6.5, I have the latest version of iTunes, 10.1.1. I'm using the Airport Extreme.
I have followed the directions to the letter!
Please help!
Thanks,
Aloha
John
I have a number of movies, etc on my pc but to make things easier, i just opted to a custom sync, display only those items i have selected, and chose 3 movies only.
I can see them on my tv, but when i select play, i always get an error indicating that this device is not authorized to play the content. I have deauthorized/authorized my pc many times.
I'm thinking about just dumping all my apple products and just stick with a microsoft based pc.

I am having the SAME issue. Just bought the Apple TV 1st Gen. from AppleStore, then followed the instructions to the letter. I am using iMac 10.5.8, Airport Extreme Base Station, AppleTV, and I have the most up-to-date iTunes and also made sure AppleTV is up to date. I get the same stupid error messages indicating the device is not authorized. Called Apple (no)Support, and was walked through restarting all my devices (like I didn't already try this, but just to make 'em happy, did it again...), didn't resolve the issue. "Steve" was like "...hmm, that shouldn't be doing that..." Really, dude? Maybe that's why I called you. Thanks for your time. Hope you guys enjoy my money I gave you.
Anyone have any ideas? I am about to pack this thing up and send it back. When I purchase ALL Apple products that are advertised as being able to just plug and go, it should freakin' work.

I can't find any error in my vi but it just doesn't work please help

I'm trying to control a robot named cs-113 and I find someone has already achieved this. He wrote a vi called robot cs-113.vi and I just tried to write a same one but it just doesn't work. Can anyone tell me why it doesn't work? Thanks for your help!
由 normanshi 在 08-01-2006 04:11 AM 上編輯的訊息
Attachments:
robot-cs113.vi ‏79 KB
cs-113 test.vi ‏62 KB

It would really help if you were a little more specific about what isn't working. Also try debugging your application in highlighted execution with probes to find out exactly what data you're sending out the port.
Jarrod S.
National Instruments

Sge2000 just doesn't route in a sane manner

Similar Messages

Maybe you are looking for