SGE2010 layer 3 problem with intervlan routing setup

I am new to the small business switches and could use some assistance in configuring intervlan routing between multiple vlans on the switch. I have changed the mode to layer 3 and setup the vlans. When I enter an IP address for VLAN2, I am disconnecting from the configuration interface (VLAN1 ip) on the switch and I cannot access the switch unless I reset it. I have tried this several times and each time it behaves the same. Is there something else I need to setup before configuring the ip address for the other VLANs?

Hi Jacqueline,
Thank you for participating in the Small Business support community. My name is Nico Muselle from Cisco Sofia SBSC.
This is the normal way for the switch to behave. There are 2 ways to work around this.
You assign a port to VLAN2. After configuration of the IP address, you connect your PC to this port and make sure it is in the same subnet as the VLAN 2 IP address.
You assign a static IP to the default vlan first and make sure your connected PC is in the same subnet.
The reason for this behaviour is, that the switch has it's DHCP client enabled, if no DHCP server is available it will revert to it's default IP 192.168.1.254 (through which I assume you connect for configuration).
However, once you configure a static IP on the switch, the DHCP client and the default IP are disabled, which means that the IP address obtained from the DHCP or the default IP of 192.168.1.254 are no longer reachable.
I would go with step 2, as this is the easiest workaround for your issue and you would want a static IP in the default VLAN anyway I suppose.
Hope this helps !
Best regards,
Nico Muselle
Sr. Network Engineer - CCNA

Similar Messages

Problem with intervlan routing on 4506...no dhcp either of course

Is anyone having an issue getting there 4500 series to route? I have turned on ip routing and nothing...they cannot see across the vlans...
I have attached the core switch (2980g) config that our cs-4506 connects too and our windows2003 dhcp configuration. Any help or suggestions greatly welcome... TIA, gary

It looks like it should work as long as you know that the workstations have an address 192.168.0.0 255.255.224.0 subnet and their default gateway on the nic is pointed to 192.168.0.253 . Put a workstation on the 2980 with say an address 192.168.1.1 255.255.224.0
and it's default gateway at 192.168.0.253 . You should be able to ping the switch address and the default gateway as they are in the same vlan and their isn't any routing involved . Then try to ping anything in vlan 3 . It should work , if not then i'm out of ideas . Just make sure you also see all your subnets in your 4500 when you do a "show ip route" . Just for grins also on the 4500 on the port that connects the 2980 put "switchport mode access and also switchport access vlan 1 . This shouldn't make any difference but can't see any other reason why it isn't working at this point.

Problem with Advanced Routing in WRT320N

Hi, everybody.
First of all, sorry for my poor English.
I've a problem with Advanced Routing in router. My provider using routing and it looks like that:
route add -p 172.16.2.0 mask 255.255.255.0 10.1.0.2
route add -p 172.16.5.0 mask 255.255.255.0 10.1.0.2
route add -p 10.0.0.0 mask 255.0.0.0 10.1.0.2
Everything is working well in XP (or other OS), but then I try to setup a Routing in router:
1.
2.
I'm realy tired to flashing and reflashing between 1.00.02 and 1.00.03, changing browsers, and hard reseting.
Anybody'll gimme a shot trick to my tired brains?
Solved!
Go to Solution.

1. Yes.
2. netstat:
C:\Users\dan>netstat -rn
===========================================================================
Список интерфейсов
31...........................inet
12...00 40 f4 76 95 bd ......VIA Rhine III Fast Ethernet адаптер
11...00 1d 92 2c 23 02 ......Realtek RTL8168B/8111B Family PCI-E Gigabit Ethern
et NIC (NDIS 6.20)
1...........................Software Loopback Interface 1
15...00 00 00 00 00 00 00 e0 Адаптер Microsoft 6to4 #2
21...00 00 00 00 00 00 00 e0 Адаптер Microsoft ISATAP #2
13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface
14...00 00 00 00 00 00 00 e0 Адаптер Microsoft 6to4
19...00 00 00 00 00 00 00 e0 Адаптер Microsoft ISATAP #3
18...00 00 00 00 00 00 00 e0 Адаптер Microsoft ISATAP
16...00 00 00 00 00 00 00 e0 Адаптер Microsoft 6to4 #3
20...00 00 00 00 00 00 00 e0 Адаптер Microsoft ISATAP #4
===========================================================================
IPv4 таблица маршрута
===========================================================================
Активные маршруты:
Сетевой адрес Маска сети Адрес шлюза Интерфейс Метрика
0.0.0.0 0.0.0.0 10.1.0.2 10.1.3.42 4501
0.0.0.0 0.0.0.0 On-link 91.203.178.26 21
10.0.0.0 255.0.0.0 10.1.0.2 10.1.3.42 4246
10.1.0.0 255.255.0.0 On-link 10.1.3.42 4501
10.1.3.42 255.255.255.255 On-link 10.1.3.42 4501
10.1.255.255 255.255.255.255 On-link 10.1.3.42 4501
91.203.178.26 255.255.255.255 On-link 91.203.178.26 276
127.0.0.0 255.0.0.0 On-link 127.0.0.1 4531
127.0.0.1 255.255.255.255 On-link 127.0.0.1 4531
127.255.255.255 255.255.255.255 On-link 127.0.0.1 4531
172.16.2.0 255.255.255.0 10.1.0.2 10.1.3.42 4246
172.16.2.10 255.255.255.255 10.1.0.2 10.1.3.42 4246
172.16.5.0 255.255.255.0 10.1.0.2 10.1.3.42 4246
224.0.0.0 240.0.0.0 On-link 127.0.0.1 4531
224.0.0.0 240.0.0.0 On-link 10.1.3.42 4502
224.0.0.0 240.0.0.0 On-link 91.203.178.26 21
255.255.255.255 255.255.255.255 On-link 127.0.0.1 4531
255.255.255.255 255.255.255.255 On-link 10.1.3.42 4501
255.255.255.255 255.255.255.255 On-link 91.203.178.26 276
===========================================================================
Постоянные маршруты:
Сетевой адрес Маска Адрес шлюза Метрика
172.16.2.0 255.255.255.0 10.1.0.2 1
172.16.5.0 255.255.255.0 10.1.0.2 1
10.0.0.0 255.0.0.0 10.1.0.2 1
===========================================================================
IPv6 таблица маршрута
===========================================================================
Активные маршруты:
Метрика Сетевой адрес Шлюз
16 1125 ::/0 2002:c058:6301::c058:6301
11 276 ::/0 fe80::f88b:9485:52cd:caaf
1 306 ::1/128 On-link
13 58 2001::/32 On-link
13 306 2001:0:4137:9e50:2846:3ccb:a434:4de5/128
On-link
16 1025 2002::/16 On-link
16 281 2002:5bcb:b21a::5bcb:b21a/128
On-link
11 276 fe80::/64 On-link
13 306 fe80::/64 On-link
13 306 fe80::2846:3ccb:a434:4de5/128
On-link
11 276 fe80::b9aa:b87b:89ea:fcdd/128
On-link
1 306 ff00::/8 On-link
13 306 ff00::/8 On-link
11 276 ff00::/8 On-link
===========================================================================
Постоянные маршруты:
Отсутствует
C:\Users\dan>
2. ipconfig:
C:\Users\dan>ipconfig /all
Настройка протокола IP для Windows
Имя компьютера . . . . . . . . . : druh
Основной DNS-суффикс . . . . . . :
Тип узла. . . . . . . . . . . . . : Гибридный
IP-маршрутизация включена . . . . : Нет
WINS-прокси включен . . . . . . . : Нет
Порядок просмотра суффиксов DNS . : mannet.lan
Адаптер PPP inet:
DNS-суффикс подключения . . . . . :
Описание. . . . . . . . . . . . . : inet
Физический адрес. . . . . . . . . :
DHCP включен. . . . . . . . . . . : Нет
Автонастройка включена. . . . . . : Да
IPv4-адрес. . . . . . . . . . . . : 91.203.178.26(Основной)
Маска подсети . . . . . . . . . . : 255.255.255.255
Основной шлюз. . . . . . . . . : 0.0.0.0
DNS-серверы. . . . . . . . . . . : 91.190.68.2
91.203.177.4
NetBios через TCP/IP. . . . . . . . : Включен
Ethernet adapter lanHOME:
Состояние среды. . . . . . . . : Среда передачи недоступна.
DNS-суффикс подключения . . . . . :
Описание. . . . . . . . . . . . . : VIA Rhine III Fast Ethernet адаптер
Физический адрес. . . . . . . . . : 00-40-F4-76-95-BD
DHCP включен. . . . . . . . . . . : Да
Автонастройка включена. . . . . . : Да
Ethernet adapter 1000LAN:
DNS-суффикс подключения . . . . . : mannet.lan
Описание. . . . . . . . . . . . . : Realtek RTL8168B/8111B Family PCI-E Gigab
it Ethernet NIC (NDIS 6.20)
Физический адрес. . . . . . . . . : 00-1D-92-2C-23-02
DHCP включен. . . . . . . . . . . : Да
Автонастройка включена. . . . . . : Да
Локальный IPv6-адрес канала . . . : fe80::b9aa:b87b:89ea:fcdd%11(Основной)
IPv4-адрес. . . . . . . . . . . . : 10.1.3.42(Основной)
Маска подсети . . . . . . . . . . : 255.255.0.0
Аренда получена. . . . . . . . . . : 17 октября 2009 г. 17:37:10
Срок аренды истекает. . . . . . . . . . : 18 октября 2009 г. 17:37:09
Основной шлюз. . . . . . . . . : fe80::f88b:9485:52cd:caaf%11
10.1.0.2
DHCP-сервер. . . . . . . . . . . : 172.16.2.2
IAID DHCPv6 . . . . . . . . . . . : 234888594
DUID клиента DHCPv6 . . . . . . . : 00-01-00-01-12-43-2B-71-00-1D-92-2C-23-02
DNS-серверы. . . . . . . . . . . : 172.16.2.2
Основной WINS-сервер. . . . . . . : 172.16.2.2
NetBios через TCP/IP. . . . . . . . : Включен
Туннельный адаптер Reusable Microsoft 6To4 Adapter:
Состояние среды. . . . . . . . : Среда передачи недоступна.
DNS-суффикс подключения . . . . . :
Описание. . . . . . . . . . . . . : Адаптер Microsoft 6to4 #2
Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP включен. . . . . . . . . . . : Нет
Автонастройка включена. . . . . . : Да
Туннельный адаптер Reusable ISATAP Interface {543B8BBE-84D2-471B-B8FB-F73600B4A8
2B}:
Состояние среды. . . . . . . . : Среда передачи недоступна.
DNS-суффикс подключения . . . . . :
Описание. . . . . . . . . . . . . : Адаптер Microsoft ISATAP #2
Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP включен. . . . . . . . . . . : Нет
Автонастройка включена. . . . . . : Да
Туннельный адаптер Подключение по локальной сети* 5:
DNS-суффикс подключения . . . . . :
Описание. . . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP включен. . . . . . . . . . . : Нет
Автонастройка включена. . . . . . : Да
IPv6-адрес. . . . . . . . . . . . : 2001:0:4137:9e50:2846:3ccb:a434:4de5(Осно
вной)
Локальный IPv6-адрес канала . . . : fe80::2846:3ccb:a434:4de5%13(Основной)
Основной шлюз. . . . . . . . . :
NetBios через TCP/IP. . . . . . . . : Отключен
Туннельный адаптер 6TO4 Adapter:
Состояние среды. . . . . . . . : Среда передачи недоступна.
DNS-суффикс подключения . . . . . :
Описание. . . . . . . . . . . . . : Адаптер Microsoft 6to4
Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP включен. . . . . . . . . . . : Нет
Автонастройка включена. . . . . . : Да
Туннельный адаптер isatap.mannet.lan:
Состояние среды. . . . . . . . : Среда передачи недоступна.
DNS-суффикс подключения . . . . . : mannet.lan
Описание. . . . . . . . . . . . . : Адаптер Microsoft ISATAP #3
Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP включен. . . . . . . . . . . : Нет
Автонастройка включена. . . . . . : Да
Туннельный адаптер isatap.{AE6B314F-94BA-478F-8751-74DEB5AB1888}:
Состояние среды. . . . . . . . : Среда передачи недоступна.
DNS-суффикс подключения . . . . . :
Описание. . . . . . . . . . . . . : Адаптер Microsoft ISATAP
Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP включен. . . . . . . . . . . : Нет
Автонастройка включена. . . . . . : Да
Туннельный адаптер Подключение по локальной сети*:
DNS-суффикс подключения . . . . . :
Описание. . . . . . . . . . . . . : Адаптер Microsoft 6to4 #3
Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP включен. . . . . . . . . . . : Нет
Автонастройка включена. . . . . . : Да
IPv6-адрес. . . . . . . . . . . . : 2002:5bcb:b21a::5bcb:b21a(Основной)
Основной шлюз. . . . . . . . . : 2002:c058:6301::c058:6301
DNS-серверы. . . . . . . . . . . : 91.190.68.2
91.203.177.4
NetBios через TCP/IP. . . . . . . . : Отключен
Туннельный адаптер isatap.{8B513FFA-4355-406F-B999-1701EE42D5B9}:
Состояние среды. . . . . . . . : Среда передачи недоступна.
DNS-суффикс подключения . . . . . :
Описание. . . . . . . . . . . . . : Адаптер Microsoft ISATAP #4
Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP включен. . . . . . . . . . . : Нет
Автонастройка включена. . . . . . : Да
3.
4. without privider's cable:
4. with provider's cable:

I need advise and help with this problem . First , I have been with Mac for many years ( 14 to be exact ) I do have some knowledge and understanding of Apple product . At the present time I'm having lots of problems with the router so I was looking in to

I need advise and help with this problem .
First , I have been with Mac for many years ( 14 to be exact ) I do have some knowledge and understanding of Apple product .
At the present time I'm having lots of problems with the router so I was looking in to some info , and come across one web site regarding : port forwarding , IP addresses .
In my frustration , amongst lots of open web pages tutorials and other useless information , I come across innocent looking link and software to installed called Genieo , which suppose to help with any router .
Software ask for permission to install , and about 30 % in , my instinct was telling me , there is something not right . I stop installation . Delete everything , look for any
trace in Spotlight , Library . Nothing could be find .
Now , every time I open Safari , Firefox or Chrome , it will open in my home page , but when I start looking for something in steed of Google page , there is
''search.genieo.com'' page acting like a Google . I try again to get raid of this but I can not find solution .
With more research , again using genieo.com search eng. there is lots of articles and warnings . From that I learn do not use uninstall software , because doing this will install more things where it come from.
I do have AppleCare support but its to late to phone them , so maybe there some people with knowledge , how to get this of my computer
Any help is welcome , English is my learned language , you may notice this , so I'm not that quick with the respond

Genieo definitely doesn't help with your router. It's just adware, and has no benefit to you at all. They scammed you so that they could display their ads on your computer.
To remove it, see:
http://www.thesafemac.com/arg-genieo/
Do not use the Genieo uninstaller!

Problem with Audio MIDI Setup using multiple accounts

I'm having a problem with Audio MIDI Setup recognizing all of the MIDI devices on a G4 Tower with a non-administrator account. The main administrator account has no problem seeing anything, but the non-admin account won't see anything. Does it all have to be added in manually, or is there a preferences file to copy over that will take care of this. Failing that, is it a problem with file permissions? Any help would be greatly appreciated.

Don't know whether this of any help, but there's an identifiable issue with AMS and Digital Performer 5 where DP5 simply won't load with AMS setups configured with previous versions of DP. Which is probably irrelevant to your problem, but ...
What I and other DP users have found we have to do is start with a completely new, blank AMS setup, and reconfigure our devices from scratch, and although this was kind of hit and miss and on the fly (don't really understand what the the issue was, exactly), I think the bottom line was if we used the new AMS setup with DP5 before anything else that might cause its data tables to change, we were ok.
So if you can do it, it might be worth setting AMS to a new blank template, then connecting your interfaces, see how far you get. And always make sure you've got the latest drivers of course, though I'm sure you've done that.
Never used Mbox or 410, but I've an Ozonic which I think uses the same M-Audio firewire drivers as the 410, and don't have any problem with that, FWIW.
G5 Dual 2.7, MacMini, iMac 700; P4/XP Desk & Lap. Mac OS X (10.4.8) mLan:01x/i88x; DP 5.1, Cubase SX3, NI Komplete, Melodyne.

Problem with rg60se router

I have problem with this router, when I connect to the internet wirelessly it works fine but when I try to connect my pc to router via cable I can't connect to the internet. maybe someone can help with this problem.

>> Posting Guide <<

Problems with first time setup

Hi to all and please be kind to this new applee. I am vary familar with Windows but not Apple.
I am having problems with first time setup. Choice wifi network ZAJ34 has full connectino bars but requires a password to connect with it. Tried to use "Connect to iTunes" and plugged in the USB cable. Windows7 ran ok and "MyComputer\Apple iPod" shows up in Explorer. All I get to is the screen that shows the cable pointing to the music symbol. I am new to Applie iPod so I am totally lost. I have the Apple iPod touch 8GB Black (4th Generation) CURRENT MODEL.
Operating System - iPod touch User Guide (For iOS 5.1 Software) downloaded, not sure.
Thanks
Wayne

I find this,
Before restoring:
Verify that you are using the latest version of iTunes. [How? I am not past selecting a network.]
Back up your device. [Do not know how, again, I am not past selecting a network.]
Transfer and sync content to your computer. [Hooked up the USB cable and nothing happens.]
Restoring your iOS device
Connect your device to your computer. [Hooked up the USB cable and nothing happens.]
Select your iPhone, iPad, or iPod touch when it appears in iTunes under Devices. Select the Summary tab, and click the Restore button. [iPod touch when it appears in iTunes under Devices, is it in Control Panel. I looked in Device Manager and so only drivers etc.

Connection problems with WRT54G Router PLEASE HELP!!!!

Hello all,
Im having a huge issue and im hoping that someone can help me. Awhile ago i changed what i believe to be my router settings using 192.168.1.1 and i believe i added WEP secuirty. I changed my password i know that much. Anyway my problem is this - When i try connecting a router to my computer, i cannot access the internet OR the 192.168.1.1 setup. I just get a yellow caution sign on my wireless settings (running Windows 7), but when i connect my cable modem (Comcast) to my computer, i can access the internet. I have reset both the router and my cable modem MANY times (hard resets) and STILL cannot get the setup page for the router. I have TWO WRT54G rourters and BOTH do the same thing when connected to my desktop , yet BOTH work fine on an old machine running XP, so it is something i did with this computer. Can someone please help me solve this issue? any hlep would be appreciated as i am stumped and do not know how to fix this and cannot use WI-FI or my Xbox 360 until i can fix this..Thanks.

Check the IP address of your computer and see if it's in range with the router's IP.
To learn how to do so, click here.

Problems with Wireless Router and Adapter

I tried posting this in the wireless adapter forum but nobody responded :-(
I'm using a WRT54G Router btw, and the firmware is v2.02.7, Feb. 27, 2004.
Hi everyone,
I have a Linksys Wireless G Router and several computers that I try to connect with. One of them is a computer running Windows XP and using a Linksys Wireless USB B Adapter (WUSB11). Another is a laptop running Mandriva Linux using a Linksys Instant Wireless Network PC Card (WPC11). Another one is running Windows Vista and using a Linksys Wireless N card. I also have a laptop running Windows XP using a Linksys Wireless-G Notebook Adapter (WPC54G). I also have another PC running Windows XP and uses a Linksys Wireless USB Adapter WUSB54G. Finally, I have two macintosh laptops running OSX and with airport devices installed.
Anyway, I have problems with my internet connection frequently being interrupted and even sometimes I won't have a connection at all for hours. This occurs with my Linux laptop, the PC with the Wireless B Adapter, and the laptop using the Wireless G Notebook Adapter. In addition to this, the macintosh laptops have internet even more infrequently. However, I seem to never have a problem with the Windows Vista desktop or the Windows XP desktop that has the Wireless G adapter. I try repairing the connection and often it does not work. I have also tried resetting the router and the cable modem. I'm not sure what else I can do. I even bought a Wireless N router and had little success with that. We even went as far as moving the wireless router upstairs into our living room, thinking that the signal was somehow suffering from interference or that distance was a factor. Anyway, sorry for the long post but I could really use some help!
Thanks.

Hi… logon to wireless N router’s setup page, open I.E. an in the address bar type 192.168.1.1 it would ask for username and password, put "admin" as a paassword (default password) without any username...linksys setup pops up, click on on wireless tab and and try changing radio band to wide 40MHz, wide channel to 9 and wireless standard channel to 1 or 11, go to advanced wireless settings reduce beacon interval to 50, fragmentation and RTS threshold to 2304, change N Transmission rate to 270 MBps…also try upgrading latest firmware on router, check whether it makes any difference or not and let me know.

TRYING TO SET UP I PAD TO HP AIR PRINTER HAD PROBLEMS WITH ,TALKTALK ROUTER, ASKED AT PC WORLD ADVISED TO BY AIRPORT EXPRESS BUT STILL NO LUCK WILL NOT COMPLETE SET UP. THOUGHT THIS WOULD REPLACE THE ROUTER, I THINK I MAY HAVE BEEN WRONGLY ADVISED

Having problems with air printer to i pad, problem seems to lie with talktalk router, hp solutions managed to get i mac to air printer working but not i pad, adivsed to buy another router as talktalk is not compatiable with bonjour. Went to PC world apple department advised to by airport express. tried setting it up using but will not finalise. i was led to believe this would replace the talktalk router? i feel i have been sold the wrong thing. Any suggestions

This happened to me when I was setting up the wireless router for a friend. The issue is with the Westall modem. You need to go in and setup the "bridge" option on the westell modem. The link below gives directions or you can call bellsouth dsl support (this is how I learned about it).
http://help.bellsouth.net/bellsouth/asp/contentview.asp?isbrowse=true&sprt_cid=3f993409%2Ddff7%2D422...
Good luck
Solution:
Method 1 - Hard Reset
Restore the modem to default settings by pressing the Reset button on the back of the modem and holding it for 3 seconds. (Bridged mode is the default setting for the Westell).
After the modem regains sync, it is in Bridged mode. Do not attempt to surf into the modem as surfing into the modem will enable the Easy Login page and convert the modem from bridged mode to a PPP mode.
Method 2 – Bridged Mode
Access the Westell interface using http://192.168.1.254 or http://launchmodem.
Click on the Broadband DSL Line button.
Click on the Protocols button
Select the radio button to the left of Option 2 (Bridge)
Click the save button. Once the modem has restarted it is in bridge mode.
ALL STEPS COMPLETE

Problems with WRT610N router

I purchased a WRT610N router yesterday, to replace my aging WRT54G, that I've been using until now to support a laptop, desktop, Xbox360 and PS3.
From opening the box, I've had problems. The LELA software wouldn't recognize my network card....an nVidia nForce network adapter. It kept giving me an error 312. I called Linksys support yesterday, and spend four hours repeately rebooting and power cycling my router, unplugging it, etc. None of this helped...despite logging directly into the router, we were unable to get it to connect to my ISP. It persistently failed to form a PPPoE connection.
Finally, the support rep advised returning it to the store, and getting a new one. I did that, and tonight, the new one did the same thing. I googled, and found articles indicating that LELA has had compatibility issues with the nVidia networking card. I advised the support agents of what I'd found, but they insisted that the router has no problem with the nVidia card.
I decided to experiment, and installed an AOPEN AON-325 ethernet card, and LELA now picks up the card fine. I then attempted to connect, but had no luck. I've spent the better part of tonight talking to support, talking to my ISP, and trying numerous things....cloning my MAC address, switching my Alcatel Speed Touch modem to a bridge, power cycling, but nothing works.
Are there compatibility issues between the 610N router and either my networking card, or my modem? Has anyone run into these problems?
I know my internet connection is working, because as soon as I unplug the cables from the 610, and hook them back up to my 54G, everything works perfectly.
At this point my ISP is going to send me a new modem, as my Speed Touch is almost 9 years old. If this doesn't fix the problem, then I don't know what the issue is.
I googled alcatel speed touch modem and WRT610, and even found some message boards with dutch users who have the same combo, and are having no success in connecting with the WRT610N.
Has anyone had similar problems?
Thanks
PLeROA

I`m at the same page of PLEFROAD...
I bought my new WRT610N router (appears on box: N ULTRAPLUS SIMULTANEOUS DUAL-N BAND... WIRELESS ROUTER... ENTERTAINMENT ROUTER FOR FASTER GAMING, MUSIC AND HD VIDEOS... AND A LOT OF BLAH, BLAH AND BLAH) when you read that you think by yousel: wow this is the one that I really need!
So I bring to my home. The setup is so easy... Just setup.
Second day = NO WIRELESS CONNECTION... Ok, I thought by myself: I did the setup, so I did wrongly. Then I start again. I reseted the (WRT610N THE BEST ROUTER EVER)... and set it up again... RESULT = WIRELESS OK.
Third day: sometimes NO CONNECTION. OK, I thought probably it is my modem, of course I just bought (and is a Linkys brand too - CM 100). Then I called to Comcast and I wasted my time trying fixed nothing. So I got sad and I went to my bed.
Forth day = The connection was bad just for little time.
Fifth day = I gave up
Sixth day = I gave up again.
Seventh day = I was injured of couse.
Eighth day = I WASTED ABOUT TWO HOURS WITH TECHNICAL SUPPORT.
Now I don`t know which is anymore... But I WASTED PRECIOUS TIME WITH A TECHNICAL SUPPORT because theoretically I have "THE BEST ROUTER EVER", SO I WANTED USE ALL FEATURES. I TRYED TO KNOW HOW TO ACCESS MY EXTERNAL HARD DRIVE THROUGHT INTERNET... RESULT = I WASTED MORE TIME.
I CHATTED WITH GOOD THECNICIANS... BUT YOU KNOW THEY WORK WITH LINKSYS, SO THEY CAN`T NOT TELL THAT YOU JUST BOUGHT A TRASH! So they try to fix the problem or just between the lines written that you`re not knowing how to connect your product.
Now I have the third problem: I just win for my birthday one WINDOWS MEDIA EXTENDER - ANOTHER LINKSYS (DMA2100).... I`M AFRAID... MY GIRLFRIEND IS GOING TO BE UPSET BUT I DON`T KNOW IF GOING TO USE.
NOW I HAVE A QUESTION FOR ALL.
WHAT I HAVE TO DO WITH MY ROUTER? IT IS NOT WORKING AND THE TIME TO RETURN IS OVER!
OR UNTILL WHEN EVERYONE HAVE TO WAIT TO LINKSYS HELP EVERYBODY.
GOD BLESS YOU ALL.
MUCHFRUSTRATED.

Problems with in-band setup on 2540FC array

I have an Ultra45 with a SG-XPCIE1FC-QF4 connected to a 2540FC. I have installed CAM software 6.2.0.13 with no problems and need to setup and manage this using in-band management.
I have looked around the download pages and I believe I need:
SMagent-SOL-90.00.00.06.pkg
and
SMruntime-SOL-10.10.02.00.pkg
for in-band management.
I was able to install the SMagent-SOL-90.00.00.06.pkg with no problems, but when I install the SMruntime-SOL-10.10.02.00.pkg I get the following errors and am at a loss for what to do next, any help is appreciated:
hostname:/2540FC-software(root)# pkgadd -d SMruntime-SOL-10.10.02.00.pkg
The following packages are available:
1 SMruntime SANtricity Storage Manager Runtime
(sparc) 10.10.02.00
Select package(s) you wish to process (or 'all' to process
all packages). (default: all) [?,??,q]: all
Processing package instance <SMruntime> from </2540FC-software/SMruntime-SOL-10.10.02.00.pkg>
SANtricity Storage Manager Runtime(sparc) 10.10.02.00
cpio: Unexpected end-of-archive encountered.
1 errors
pkgadd: ERROR: attempt to process datastream failed
- process </usr/bin/cpio -icdumD -C 512> failed, exit code 1
pkgadd: ERROR: unable to unpack datastream
Installation of <SMruntime> failed (internal error).
No changes were made to the system.

Well, I am using from CDROM for CAM 6.2
checksum:
1013790347 100432384 SMruntime-SOL-10.30.02.00.pkg
used it on solaris 10.
Please compare the checksum.
Edited by: nitin.k on Feb 11, 2009 10:01 AM

OSPF with InterVlan Routing

Dear All,
Please help me about it ...
The same network I have designed and working fine on the RIPV2 but I want it on the OSPF but it works on the packet tracer but not on the GNS3. In this diagram there are multiple areas and there are three ABRs connected to the backbone area. The others interfaces are in the area1, area2 and area3 respectfully and in that side I need the intervlan routing.
Is it possible in the ospf the same like in the diagram ?
What type of OSPF (Point to Point or Point to Multipoint ) will be required as the R1 is the backbone router further connected with the Internet on the BGP. ?
Please sir, advise me about it.
Thanks
Best Regards
Ali Khan

Hi Jon,
Thank you very much,
1) The link between the ABRs and R1 is the wireless 1.4gig bridge link on the 5Km distand and the interface is configured with IP ospf network point-to-point.
2) On the packet tracer all the neibour displayed with its router-id, even on GNS3 but it does not show the route of other interface like area 1 or area 2.. Means the backbone router do not show the routes of other areas..(area 1 or area 2 and area 3)
3) i have tried alot and i dont think that i missed any route but the backbone area do not show the routes of subnterface (for Vlan, Router on the Stack).
Thanks
Ali

Problem with exchange account setup

Hello -
I have a user who is having a particular problem with her iPhone. We had setup an exchange account on the device and it has been working great until this week. Now when she tries to access the exchange email account the phone freezes and eventually boots you to the home screen with no error message.
We are unable to delete the account and re-create it. When we go into the mail account screen we cannot access the exchange account settings, it does the same thing freeze up and return to the home screen. Next we tried reseting the phone back to factory defaults but the exchange account did not reset (everything else did). With no way to delete the account we cannot create a new one.

Sorry, but it is still not clear.
When restoring an iPhone with iTunes, the iPhone is completely erased first followed by the firmware being reinstalled. After the firmware is reinstalled, there are two options. Restore from the iPhone's backup which is selected by default, or as a new iPhone which must be manually selected.
Did you do the latter? If so, this is the first time I have seen this reported - that everything was erased from the iPhone except for a single email account.

Problems with call forwarding setup

I just got an iPhone and it's great, except for one annoying problem with the call forwarding behavior.
With my old RAZR phone (also on AT&T) I had two choices when turning on forwarding, "forward immediately" or "forward when unavailable". I used the second choice and had forwarding turned on all the time. Calls would go to the cell phone first but then forward to my home number if I was on another call or didn't answer after a couple of rings. That behavior is important because I want all voice messages in the same place, on my answering machine at home, regardless of whether my cell or home number was called (so I want to deliberately bypass AT&T's voicemail system).
However the iPhone seems to only have the "immediately" behavior, which means I don't have a chance to answer a call on the iPhone before it forwards, and the iPhone doesn't even log it as a missed call. The forwarding setup is stored in AT&T's system so it seems like the capability should be there regardless of the type of phone, and this is just an arbitrary user-interface restriction with the iPhone. Anyone know how to work around this and get the "forward when unavailable" behavior?

Jason -
Thanks, this did the trick. The instructions under the section for "former AT&T Wireless customers" worked perfectly (perhaps because I am actually a former AT&T Wireless customer; I've had the number for almost 6 years, since before the merger with Cingular). Anyway, I dial 61xxxxxxxxxx# (xxx = the number to forward to), make the call, and a confirmation message appears on the screen; now the forwarding is working just the way I like it.
Thanks again!
Bob

SGE2010 layer 3 problem with intervlan routing setup

Similar Messages

Maybe you are looking for