SH VER and Dir Bootflash - Show differant mem sizes!!!!
A sh ver shows 32 meg, while a Dir bootflash shows 16 meg. Shouln't these values be the same?. Device is a 6509. I need know if this is OK as I wish to upgrade the IOS.
From SH VER:
DRAM FLASH
Total Used
32768K 23633K
Uptime is 450 days, 1 hour, 31 minutes
frmad00-02-c65-sw> (enable)
dir bootflash:
-#- -length- -----date/time------ name
1 5849256 Nov 29 2003 11:42:40 cat6000-sup2.6-3-7.bin
9354968 bytes available (5849384 bytes used)= 16 Meg
Any Ideas?
Regards,
Pat
Hello,
DRAM Flash & Bootflash are different memories.
DRAM Flash is used to hold CatOS Or IOS
Bootflash is used to hold the System images which is used for booting.
When you start the Router/Switch first the Lower version IOS (Bootstrap version) is loaded from Bootflash (also known as ROM or Onboard Flash)
With the help of this image the IOS (which is in DRAM Flash)is loaded.
You can see both the IOS by giving the following command
Router#sh version
Follow this for more information
http://www.cisco.com/en/US/products/hw/switches/ps663/products_tech_note09186a00801a5d58.shtml
Regards
Krishnamurthy suresh
Similar Messages
-
HI Team,
Recently we copied data from Version O to Version EFC using T code CJ9F , When running CJ9F to copy V0 to EFC, the work centre rate has updated in Version EFC with the latest from Version 0 , Therefore, the CJR2 entries in version 0 (original) and EFC (copy) show different ? amounts: is this correct?
My Analysis on the above incident between two Versions
Version EFC
1. Version EFC consist checkedu201D Integrated planningu201D check box
2. Exchange Rate type u201CMu201D ,
3. It doesnu2019t consist any u201Cvalue date u201C
4. checked u201C integrated planning with cost center / bus. Process.
Version u201C 0u201D
Version u201C Ou201D doesnu2019t checked u201C integrate planning check box from 2003 fiscal year
2 . Exchange rate type u201C Pu201D u201C
3 .value date u201C 01.04.2003
4 . unchecked u201Cintegrated planning with cost center / bus. Process
where is the data corrected can any one guide me and let me know if any steps are missing
thanks
RanamkaHi kim standley,
Thanks for using Apple Support Communities. I would first try resetting SyncServices as described here:
Mac OS X: Resetting the SyncServices folder
http://support.apple.com/kb/TS1627
If the issue persists after that, I'd move on to this article:
Sync Services: Advanced troubleshooting for contact and calendar syncing
http://support.apple.com/kb/ts2481
Cheers,
- Ari -
Variance Scaling in Query and Web Template Showing Different Results
Hi experts,
I have the following problem - variance scaling in my query and web template are showing different results.
My variance in column is set as follows:
Formula: NODIM(A % B)
Scaling Factor: 1
I have a structure in row that uses Scaling Factor of 1,000.
Let say the value of Column A is 120 and Column B is 100.
When I execute the query, it will show 0.02
However, when I execute the web template it will show the correct scaling i.e. 20.
May I know what can I do to correct above scaling error?
Thank you!You can not remove the scalling factor, but once you check the checkbox below the dropdown menu, the scalling factor will go away.
I checked at my end and when I set the scalling fact as 1, I was getting 9.9% while I was expecting 9900%. When I removed the scalling factor I started getting 9900%.
I would let you know if I came across anything else.
What about the unit of Column A and B. Are they same or different?
- Danny
Edited by: Danny Matt on Jun 22, 2009 1:54 PM -
Why do copied files show different file sizes than the original files?
When I copy files (to another drive, folder, etc.) some show the same file size as the original, but others don't.
I'm guessing this is not abnormal, but what causes it?
Thanks.Hi dymar,
Copying to another Drive is understandable, they may have a differentnumber of Blocks allocated per file, for insnce a one Byte file might take up 512 bytes, 1024 Bytes, etc, but a Get info should show the actual size of the file within that/those blocks.
If copying to another Format, like MS-DOS, Forks may be lost also.
There are ways to actually Compare the files...
http://www.hutsby.net/2008/01/apple-mac-osx-compare-files-and-folders.html
http://www.deltopia.com/compare-merge-sync/macosx/
http://www.macworld.com/article/49584/2006/03/cmpfldr.html
http://www.araxis.com/merge_mac/index.html
Or the most expensive one & my favorite, but far more useful, Tri-Backup...
http://www.tri-edre.com/english/tribackup.html -
I am still having issues with the TOC pictures. I got several chapter/section photos to show up, but can't seem to repeat this success. It is some mystery that happened during a time that I had practically given up. This should be such a simple thing. Drag and place a picture into the placeholder and it shows up in the TOC....right? Help, help help! want to get this thing done and it's taken two days of work just get some of the photos to show up. I am going to have to publish this ibook with no photos in several sections.....why can't this be simple? I have even had someone else spend hours trying to figure this out. This software is such a GREAT idea....come on...help with this little part of it.
I had the same problem myself. I got to the point where I couldn't replace the photo, of a new chapter, in the TOC. What I did was to duplicate an existing chapter that was working and was able to replace it's TOC's photo. I also found that if you try different areas of the photo you can sometimes get it to replace correctly. For example, instead of dragging the new photo to the middle of an existing photo, try dragging it to the right top corner.
-
User_lobs and user_segments view shows different tablespace for lob segment
Hi,
I am trying to move lob in different tablespace for partitioned table.
I used
alter table <table_name> move partition <partition_name> lob(lob_column) store as (tablespace <tablespace_name>);
alter index <index_name> rebuild partition <partition_name> tablespace <tablespace_name>
ALTER TABLE <table_name> MODIFY DEFAULT ATTRIBUTES TABLESPACE <tablespace_name>
ALTER INDEX <index_name> modify default ATTRIBUTES TABLESPACE <tablespace_name>
Database - 10.2.0.5
OS- HP Itanium 11.31
I can see in user_lob_partitions, user_segments and user_part_tables shows me new tablespace information
whereas user_lobs and user_part_indexes shows me different information regarding tablespace.
I checked some documents in metalink but didnt help me.
I think that I am missing something or doing some step wrong.
Please help.
SQL> select partition_name, lob_partition_name, tablespace_name from user_lob_partitions where table_name in ('TRB1_PUB_LOG','TRB1_SUB_ERRS','TRB1_PUB_LOG') ;
PARTITION_NAME LOB_PARTITION_NAME TABLESPACE_NAME
S2000 SYS_LOB_P8585 USAGE_REORG_TBS
S2001 SYS_LOB_P8587 USAGE_REORG_TBS
S2003 SYS_LOB_P8589 USAGE_REORG_TBS
S2004 SYS_LOB_P8591 USAGE_REORG_TBS
S2005 SYS_LOB_P8593 USAGE_REORG_TBS
S2006 SYS_LOB_P8595 USAGE_REORG_TBS
S2007 SYS_LOB_P8597 USAGE_REORG_TBS
S2008 SYS_LOB_P8599 USAGE_REORG_TBS
S2010 SYS_LOB_P8601 USAGE_REORG_TBS
S2011 SYS_LOB_P8603 USAGE_REORG_TBS
S2012 SYS_LOB_P8605 USAGE_REORG_TBS
S2013 SYS_LOB_P8607 USAGE_REORG_TBS
S2014 SYS_LOB_P8609 USAGE_REORG_TBS
S2015 SYS_LOB_P8611 USAGE_REORG_TBS
S2888 SYS_LOB_P8613 USAGE_REORG_TBS
S2999 SYS_LOB_P8615 USAGE_REORG_TBS
S3000 SYS_LOB_P8617 USAGE_REORG_TBS
S3001 SYS_LOB_P8619 USAGE_REORG_TBS
S3004 SYS_LOB_P8621 USAGE_REORG_TBS
S3005 SYS_LOB_P8623 USAGE_REORG_TBS
S3006 SYS_LOB_P8625 USAGE_REORG_TBS
S3007 SYS_LOB_P8627 USAGE_REORG_TBS
S3008 SYS_LOB_P8629 USAGE_REORG_TBS
S3009 SYS_LOB_P8631 USAGE_REORG_TBS
S3010 SYS_LOB_P8633 USAGE_REORG_TBS
S3011 SYS_LOB_P8635 USAGE_REORG_TBS
S3012 SYS_LOB_P8637 USAGE_REORG_TBS
S3013 SYS_LOB_P8639 USAGE_REORG_TBS
S3014 SYS_LOB_P8641 USAGE_REORG_TBS
S3015 SYS_LOB_P8643 USAGE_REORG_TBS
S3050 SYS_LOB_P8645 USAGE_REORG_TBS
SMAXVALUE SYS_LOB_P8647 USAGE_REORG_TBS
32 rows selected.
SQL> select TABLE_NAME,COLUMN_NAME,SEGMENT_NAME,TABLESPACE_NAME,INDEX_NAME,PARTITIONED from user_lobs where TABLE_NAME in ('TRB1_PUB_LOG','TRB1_SUB_ERRS','TRB1_SUB_LOG') ;
TABLE_NAME COLUMN_NAME SEGMENT_NAME TABLESPACE_NAME INDEX_NAME PAR
TRB1_SUB_ERRS GENERAL_DATA_C SYS_LOB0006703055C00017$$ TRBDBUS1LNN1 SYS_IL0006703055C00017$$ YES
TRB1_SUB_LOG GENERAL_DATA_C SYS_LOB0006703157C00017$$ TRBDBUS1LNN1 SYS_IL0006703157C00017$$ YES
TRB1_PUB_LOG GENERAL_DATA_C SYS_LOB0006702987C00014$$ TRBDBUS1LNN1 SYS_IL0006702987C00014$$ YES
SQL> SQL> select unique segment_name ,tablespace_name from user_Segments where segment_name in (select SEGMENT_NAME from user_lobs where TABLE_NAME in('TRB1_PUB_LOG','TRB1_SUB_ERRS','TRB1_SUB_LOG') );
SEGMENT_NAME TABLESPACE_NAME
SYS_LOB0006702987C00014$$ USAGE_REORG_TBS
SYS_LOB0006703055C00017$$ USAGE_REORG_TBS
SYS_LOB0006703157C00017$$ USAGE_REORG_TBS
SQL> select unique segment_name ,tablespace_name from user_Segments where segment_name in (select INDEX_NAME from user_lobs where TABLE_NAME in('TRB1_PUB_LOG','TRB1_SUB_ERRS','TRB1_SUB_LOG') );
SEGMENT_NAME TABLESPACE_NAME
SYS_IL0006702987C00014$$ USAGE_REORG_TBS
SYS_IL0006703055C00017$$ USAGE_REORG_TBS
SYS_IL0006703157C00017$$ USAGE_REORG_TBS
SQL> select unique index_name,def_tablespace_name from user_part_indexes where table_name in ('TRB1_PUB_LOG','TRB1_SUB_ERRS','TRB1_SUB_LOG');
INDEX_NAME DEF_TABLESPACE_NAME
SYS_IL0006702987C00014$$ TRBDBUS1LNN1
SYS_IL0006703055C00017$$ TRBDBUS1LNN1
SYS_IL0006703157C00017$$ TRBDBUS1LNN1
TRB1_PUB_LOG_PK USAGE_REORG_IX_TBS
TRB1_SUB_ERRS_1IX USAGE_REORG_IX_TBS
TRB1_SUB_ERRS_1UQ USAGE_REORG_IX_TBS
TRB1_SUB_ERRS_2IX USAGE_REORG_IX_TBS
TRB1_SUB_LOG_1IX USAGE_REORG_IX_TBS
TRB1_SUB_LOG_PK USAGE_REORG_IX_TBS
SQL> select unique def_tablespace_name from user_part_tables where table_name in ('TRB1_PUB_LOG','TRB1_SUB_ERRS','TRB1_SUB_LOG');
DEF_TABLESPACE_NAME
USAGE_REORG_TBS
Please let me know if some more details required.>whereas user_lobs and user_part_indexes shows me different information regarding tablespace.
do you see different results after starting a new session after the ALTER statements were issued? -
Lightroom libary and development tool shows different colors
My problem is, that photos are shown different in color between libary and development tool in Lightroom 3.6. The libary shows corrected color in photos, the development tool not.
When I switch between libary and development tool sometimes, the development tool shows then the same colors.
AlfredIs your monitor profiled and calibrated, with a hardware tool (e.g. Spyder, Colourmunki etc)?
If there's no profile, or it's faulty, there can be problems. In Develop module LR uses ProPhoto RGB colour space, but in Library module it uses Adobe RGB. They'll look different if colour management isn't working, which requires a monitor profile that contains colour space information. -
LR2 and PS Eelements8 show different RGB for the same color - Please, HELP
LR2, Elements 8, Color Chart 24 (CC24),
Please help. I may need to reset LR2 to factory default or to something else.
For the following RAW adjustments the tone curve set to Linear, Contrast and Brightness to 0
I have photographed a CC24 in RAW. Opened image in Elements 8 and adjusted Exposure to 243 for the White patch #19
Then with with WB tool clicked on the 50% Gray and then readjusted exposure for the CC24 listed 243 for #19.
Now all Gray patches #19 through #24 as listed in the table or very close R=G=B (243, 200, 160, 122, 85, 52)
The RGB numbers for Red Patch #15 are R=169, G=58, B=63
The CC24 listed RGB for Red patch #15 are R=175, G=54, B=60
Also saved the adjusted image as JPG
Then opened the image in LR2 and adjusted exposure and WB as described above for Elements 8.
The Gray patches #19 through #24 show RGB numbers as listed in the table or very close.
The RGB numbers for the Red patch #15 are R=138, G=84, B=64.
However the CC24 RGB for Red patch #15 are R=175, G=54, B=60
Exported the image as JPG
Then opened the two saved JPG images in Elements. these two images read almost identical RGB numbers for each patch.
How can I fix LR2 RGB reading. Recently I have saved as defaults the tone curve set to Linear, Contrast and Brightness to 0 and probably did it wrong. My be I need to reset LR2 to the factory defaults to restore its correct reading or something else.
Please help.
LeonidQ1. Is that means that when LR2 Exported RAW to JPG the correct numbers resulted from conversion?
You should be careful with the term RGB numbers. Such numbers are only useful when you know the working space. For example, sRGB, adobeRGB, prophotoRGB, melissaRGB, etc. The numbers I calculated are simply the reference numbers (find them here: http://www.brucelindbloom.com/index.html?ColorCheckerRGB.html ). I recalculated the values in the display space used in Lightroom from Bruce Lindbloom's values in normal prophotoRGB which is a simple arithmetic excercise. When Lightroom exports a jpeg, you can set the color space in the export panel and it will do the conversion for you meaning that it will translate between its internal colorspace and the desired export color space. In an external program, you will usually be working in sRGB, adobeRGB, or prophotoRGB, which are the three main spaces that Lightroom exports to. As you can see from Bruce's tables in the link above the RGB values for these patches in all these spaces are different.
For example RGB for MacBeth CC24 Red patch (#15) was shown as 203, 0, 0 and x-rite RGB is 174, 54, 60.
They are actually the exact same chart. As I say above the values are meaningless if you don't know the colorspace. The first RGB triplet you quote makes no sense at all. It does not correspond to any colorspace listed for the MacBeth chart. The zeros indicate that the color is far outside of the gamut of the used color space, so the value is basically useless. The second is sort of close to the sRGB value.
Q.2 Would it mean that your shown table should not be applied to (used with) x-rite CC24 but to MacBeth only?
They should be pretty good for both as the chart is supposed to be the same.
Q3. Have you created your posted LR table or it was provided by Adobe?
I created it myself. Since you have a colorchecker, you should look into creating a camera profile using it. This can be done with X-rite's excellent passport utility (free download from their website), or with Adobe's free DNG profile Editor. Simply shoot a chart in the right light conditions and run the raw/dng file through this utility and a profile is created that will allow you to get very good color rendering from your camera if you shoot raw. -
Month view and detail view show different times
I'm importing this calendar:
http://www.mychurchevents.com/calendar/ical/2330512/public.ics?tz=z88
Here is my problem:
The meeting shows in Month view as 10AM, but the details show 9AM. 9AM is the correct time. It's only a problem during Daylight Savings Time. I've switched every Time Zone Control I can find with no change, and I don't want to have to change each event.
This calendar imports perfectly on any iOS device. This is only an issue in the Calendar app on OS X Mavericks.
Feel free to import the calendar and work on it.
Thanks!Robert,
I imported the calendar, and duplicated your observation, until I edited "to:" to display a 1 hour event. I also used my time zone.
My Screen Shot displays a one hour event which displays the correct start time as follows: -
Migo and Batch master showing different vendor
Hi Experts,
Process Followed:
1. In Migo Screen selecting goods reciept and Others and movement type 901 i will enter all the details such as material, quantity, plant,vendor-X and then click on check then system creates internal batch number.
2. After System creates the internal batch number i will change from Vendor - X to Vendor Y in migo and save it
3. Then if i see the batch master then system is showing the Vendor X in batch master instead of Vendor Y.
Please let me know how can i update the vendor in migo the same to batch master after changing in Migo. Please find the attachments
Regards
BadariHi,
Seems to be the error mentioned in the note: 1695572 - Incorrect vendor in batch for goods receipt of consignment. You may check the note and proceed accordingly.
Regards,
AKPT -
RAID Admin and Disk Utility show different sizes
Hello all,
I have tried searching through these forums for a resolution to this, but did not really find one. Here is my situation:
I have an XServe Dual G4 in a branch office. It has attached to it an XServe RAID. Last week, when I was down working in the office I added a new drive to the RAID. The lower channel on the RAID had 4 172GB drives in it, and I added a 5th and and told RAID admin to resize the RAID.
The next day, the RAID was finished resizing. RAID admin was reporting that the array was now 690GB. However, after rebooting the server and RAID multiple times, Disk Utility in OS X is still showing that the Volume on the RAID is only 517GB.
So, I have a couple of questions:
1. How is it possible that by adding a 172GB drive to a RAID 5 array that was about 520GB I ended up with an array that is 690 GB? That would imply that there is no parity (since 690 - 520 = 170 and the drive I added in was 172GB).
2. How do I get the server to see the additional space? The server is at the newest version of the OS and the RAID it as the newest version of the firmware.
Please help.
Mac OS X (10.4.8)I've run into the same issue with a newer PPC XServe. However, after I tried to reformat, I still only show up with the orginal size, and not the new size, even after I restarted the server and XRAID.
Did you have any success with your reformat? -
Coursemanage and iTunes U show different order
I have a course I have created in iTunes U Course Manager, "Intro to JavaScript - Google Docs Spreadsheet". I have all the posts in order in the CourseManage but when they are published as the course in iTunes U the posts are out of order.
Course: http://itunes.apple.com/us/course/intro-to-javascript-google/id502871512
How can I get the order to be correct in the course in iTunes U when I download the course to my iPad?
Thanksnothing?
-
Ipod shows different available size...
then itunes does when my ipod is connected. I have the 60gb video, which after formatting is 55.6gb available for music/movies/photos and whatnot. Now the other day, I was getting some music from my friend and was using his cord. I moved the ipod while it was connected and all of a sudden it disconnected. I checked to see if all my music was still there, but it wasn't. It erased everything. I finished loading up the music from his computer and went and hooked it up to my computer. The ipod and itunes said that the available space was the same, and there was no problem getting my computer to recognize the ipod. Then last night, i hooked it up and it would flicker between connected to the computer and not. it would barely recognize it unless i held it a certain way. the cable shouldn't be bad because i just bought the ipod last week. thats also when i noticed that itunes showed 1800 songs and only 46 gb of available space. i ejected the ipod to check and see what the ipod said it had available. it showed 1800 songs and 52.6 gb of available space. what should i do? restore it and reload all my songs on it? the ipod version is 1.1.1 and i'm not sure what version of itunes i have. Any help is appreciated.
I have the 60gb video, which after formatting is 55.6gb
This is correct.
I was getting some music from my friend
Please don't STEAL music.
what should i do? restore it and reload all my songs on it?
Yes.
Restore will fix most problems related to disk space used. -
PDF showing different version on iphone than PC
Hello,
I received a PDF via email. When the pdf is opened on the PC and iphone, it shows different version, Can you give me the solution? Thanks
Using iOS 5.0 and using Win7 for PC.using Adobe's Reader for the iOS
-
FSV showing different values when executed by different users
Hi Experts,
While executing FSV throug RFBILA00 we are getting different values when executed by differet users. Variant selection is same except the user (which is different). For one user report is perfect for another user some GL accounts were not displayed and some accounts shows different values.
Anybody could help on this. Is there any userwise settings are there.
Thanks in advance.
Regards,
NarayananHi,
check user authorization, maybe one user has limited display authorization for some values (as they are linked to specific profit center,...)
BR Christian
Maybe you are looking for
-
How do I use an Edge Animate project with SVG files in InDesign for DPS output?
Is there any way to include an Edge Animate web content using .svg files in InDesign for output to DPS? Edge Animate works great with InDesign, except for when you're using SVG files. I've worked with SVG files on the web successfully (writing .htacc
-
How do I get music from spotify transferred to my itunes library?
I need to get my music playlist on spotify downloaded to my ipod nano. It says I have to import it to itunes, when I try nothing happens. How do I do this?
-
Attachments still not opening even after new September Update??
I hope someone might be able to shed some light on this. After the new update I sent myself some word, excel, pdf attachments thinking to try the tilt/landscape feature in viewing attachments, but nothing. The attachment still shows up as a bar with
-
Restart of iMac - frozen restart
After having pressed the start/stop butten on the back of the computer to finish (instead of proberly running down the machine) the Mac stops upon a restart and having typed in my password. All iscons are visible but nothing goes further... What can
-
Losing internet connection with youtube in safari
I keep losing Network connection after i use YouTube in safari. Need to restart iPad to get connection again. Anyone an solution? I Re installed already 2 times but without any luck.