Share snapshots here, Air Port Extreme and 2 Air Port Express are working
is there a way to attach snapshots here
after 1 week I fig out how to get it to work in windows XP using my FIOS router and my Air Port Extreme, but before anything make sure you have the MAC address of all the Apple devices
As I config my devices(Air Port Extreme and 2 Air Port Express) I took snapshots since I did not want to go through this again
Unfortunately, if the light is out, the outboard power supply has failed, or the internal power supply has failed.
If you have a voltage tester, check the outboard power supply for 12 volts. If it delivers 12 volts, then the internal power supply on the AirPort Extreme has failed, and you will need to replace the AirPort Extreme.
If the outboard power supply does not work, you might be able to replace that outboard power supply to get things working again.
Take the AirPort Extreme to an Apple Store....if you have one near you.....to let them take a look.
Similar Messages
-
How do I set up my air port extreme to do port forwarding? Running 10.7.4 I have a IP camera on my local wireless net work that I want to use from my iPhone 4s and other computers.
In most cable systems, the router you have will plug into your modem and just work automatically. A NAT (Network Address Translation) router takes your external IP and hands out LAN (Local Area Network) based IPs. All of the devices you are working with right now should handle the change automatically unless you've changed from the default automatic configuration.
The problem with your wireless end of this is that the iPhone is not yet 802.11n, only 802.11g. Because that router is not dual band, all of your wifi devices will be forced to slow down to 802.11g speeds. This won't matter much for each device that's connecting to the internet, as your bottleneck is still going to be there. Where you will see slowdowns is device to device connections, like transferring data between the devices. -
The difference between AIR-ANT5135D-R and AIR-ANT5135DB-R
Hi,
Anyone know what is the difference between AIR-ANT5135D-R and AIR-ANT5135DB-R ?
From the dynamic configuration tools for 1252 and 1242, AIR-ANT2422DB-R is inside one of the antenna option.
However, I can't find it in the "Cisco Aironet Antennas and Accessories Reference Guide"
http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/product_data_sheet09186a008008883b.html
Inside the document there is only AIR-ANT5135D-R.
likewise for the 2.4 GHz, AIR-ANT2422DB-R is inside the dynamic configuration tools and not inside "Cisco Aironet Antennas and Accessories Reference Guide"
Any help would be appreciated
Thanks,
RichardFound the difference, AIR-ANT5135DB-R and AIR-ANT2422DB-R are non-articulating antennas.
Thanks!
Richard -
Every other function works perfectly, and my Internet/router are working at top speed. I can watch HD Netflix and YouTube but nothing via my iTunes library on my MacBook or iPad. All software is updated. The AppleTV will recognize that Air Play is trying to do it's thing, but with music files it sounds like they're skipping and video files just load endlessly.
I'm searching for an answer to almost the same exact problem, using almost the same exact hardware and software. Has an answer been found?
The files that I'm trying to burn come from eMusic, and they are formatted mp3. Recently, (after the iTunes update to 9.2.3?,) they would not drag and drop from iTunes into Toast. From several different discussions I've tried working around this by dragging to the desktop first then dragging and dropping to Toast, going to Toast from a programmer's homemade help window, " iToons," and today, after talking with Apple support, going directly to Toast from my eMusic folder. Alas, all recordings do not perform like they use to. Sometimes they play and sometimes not. There is one I managed, that is listenable, but sometimes I have to put it in my car stereo over and over again as it gets ejected with an error code, sometimes, finally it takes it... Some of the recordings on other disks I've burned are not clean - they have white-noise sounds creeping in... I use to have none of these problems. One time as I was listening to a CD that managed to play, and it just stopped playing... Is there an answer out there to get back to how it use to be? Thanks for you help. -
What is the difference between the airport extreme and the airport express?
What's the real difference between the airport extreme and the airport express except for the price and the size? Does one transmit with more range?
Range is about the same, maybe a bit better on the Extreme, which has better antennas.
The AirPort Exreme has Gigabit (1,000 Mpbs) Ethernet ports and the USB port will support a hard drive.
The Express has 10/100 (up to 100 Mpbs) Ethernet ports, and will not support a hard drive at the USB port.
The Express has audio capability for AirTunes while the Extreme does not.
If you don't need to connect a hard drive and don't need the faster Ethernet ports, the Express is a good value.
All the details here:
Compare Apple Wi-Fi base stations AirPort Express AirPort Extreme Time Capsule -
Using the In port.vi and Out port.vi in LabVIEW access my the Cards(Home made)
Hi Everyone,
I have got the Cards (home made 8 bit and 16 bit ) plug in at slot ISA my PC (I am using the commands inport and outport (addressed with 318-31A Hex) in C language to access very good).This now,I want to use LabVIEW language to access data directly to Port at my the Cards. In LabVIEW, Can I access data to port using the In port.vi and Out port.vi located in the Advance?
My English is poor, you don't laugh when you read it.
Thank you a lot.SachaE wrote:
> LabVIEW 7.0 cannot use the built-in In/Out Port VIs with a 32-bit
> address. Instead, you will have to use the versions of these VIs found
> in previous versions of LabVIEW.
Are you talking about physical memory access here? If so that is
something entirely different. The Intel x86 architecture uses a separate
IO address range which is entirely separate from memory space.
And at least up to the first Pentium models it was definitely never
possible to address more than 16 bits for IO address space.
This of course has gotten a little more complicated nowadays with many
PCI boards being actually mapped into memory address space instead of IO
address space. So eventhough a PCI board is more like an IO device it
often is accessed in the memory space.
> Actually, the In Port and Out Port VIs are intended for 16-bit port
> I/O and not for writing to arbitrary addresses in memory. For this
> reason, writing to 32-bit addresses never should have been allowed.
I think the VIs to access physical memory addresses were different than
the ones to access IO addresses. And yes it is definitely not a good
idea to have an application poke into physical memory as it could
completely screw the system to the point where you couldn't start it
anymore. Also IO devices mapped into memory address space are almost
always typically plug and play devices, so their address is not really
fixed and you need to do quite some more work on OS level to enumerate
your hardware and find the resources used before trying to access it.
This is something not really suited to try to do in LabVIEW and
therefore should be at least implemented as DLL but in fact anything but
a device driver is a very bad kludge.
> One possible work-around would be to use NI-VISA to perform
> register-level programming. NI-VISA gives you access to any PXI/PCI
> board, not only NI boards, and can be used to access the board's
> registers.
>
> http://zone.ni.com/devzone/conceptd.nsf/webmain/ADF3152837E2B4A486256B5600642AC7?opendocument
Thanks for this. Didn't now this existed in NI-VISA. Will check it out.
Rolf Kalbermatter
Rolf Kalbermatter
CIT Engineering Netherlands
a division of Test & Measurement Solutions -
What is the difference between the AirPort Extreme and the airport express base station and which one can extend my wifi router.
With rare exceptions of a few older routers, neither one can extend a non-Apple router's network wirelessly - they are not designed that way - but you can extend the wireless network if the Extreme is hardwired to the router or you can connect wirelessly and join the network as an access point that will provide remote ethernet access but not produce or extend the wireless signal - here is a comparison of the Apple base stations - http://www.apple.com/wifi/
-
A very good friend of mine dropped her iphone into water and now it is not working.Her husband recently passed away and text messages from him and from well wishers after his decease are feared lost. Is there any way to retrieve them?
I suggested contacting Compub in Nassau St as the info is priceless and worth the trouble of trying to regain?
Any thoughts? The poor lady is very distressIf she has backed up her iPhone she can replace that iPhone and set up the new iPhone from her backup.
You can put the iPhone that went into water into a plastic baggie with either new silica gel packets (preferred) or raw rice and let it sit for 4 - 5 days. After that time remove the phone and connect it to power for at least a half hour. While it is still connected to power reset it by holding down the power and hold button, wait for the Apple logo then let go of the buttons. Might take several tries. If it revives immediately back it up. -
It keeps telling me that one of the USB devices for this computer has malfunctioned and windows does not recognize it. I have tried all of the ports and still am not having any luck. I have purchased 3 brand new cables and none of them are working. I have tried to update the driver but it says I am using the most up to date. I have tried to reset the Ipod by holding the center button and menu button until the apple appears. I am not sure what else to try. Any help would be greatly appreciated. My computer is Windows Vista!
Hello butterflygirlie,
Have you tried uninstalling the driver for your iPod from within Device Manager? After uninstalling it, go ahead and unplug your iPod and plug it back in. Doing so should cause your system to locate the proper driver for it.
B-rock -
white screen appears instead of the wallpaper after starting up and all the funtions are working properly like the brightness and the vol
Hello again V.K,
I'm taking the computer to assistance as suggested. Even tho I'm almost 100% sure that this isn't a hardware issue.
Here is why I'm not wasting my time on my affirmative. I'm computer science bacharelor, I know about computer architeture and S.O architeture and also I'm computer developer for more than 10 years now. All behaviors presented have no connection with hardware problems. What I'm trying to say is that I'm not just saying things for saying, I have a logic behind what I say.
For a short example, whenever mouse right click stops working on a specific window/software, if I click on the window top border and drag it around and go back to the window content, the click works again.
Also, my keyboard and mouse work via usb. Usb is working normally. If I plug a usb memory stick it shows that usb is working as it should be.
On windows, right button click is also not working inside any software window, but if I click on start button, icons on desktop, anything on windows epxlorer, it works as it should be. Isnt't there bootcamp underneath windows ?
on top of it, it's a brand new mac, i have it for 5 months.
All these people that have the same problem, do u think all of them have hardware issues? Do you think Apple would keep releasing new computers with hardware problems and they wont have any information/recall for them? and worst, the problems start in a random date ?
This is my first mac and all these problems, being hardware or not, makes me lose all confidence on Apple products.
Davi. -
How to Check source systems in RSA1 and verify that connections are working
How to Check source systems in RSA1 and verify that connections are working ok and how to Check Planning Area have green status.................
Hi,
In rsa1, go to 'Tools' and option 'Manage Source System' - the screens are self explanatory there after. To check the planning areas, go to transaction /SAPAPO/MSDP_ADMIN anc check the status of the relevant planning areas.
Regards
Vinod -
Speakers have quit working no sound and it says they are working fine
Speakers have quit working no sound and it says they are working fine
Hi,
Try the following.
Download the IDT Audio installer on the link below and save it to your Downloads folder.
http://ftp.hp.com/pub/softpaq/sp55001-55500/sp55036.exe
When done, open windows Control Panel, open Device Manager and open up Sound, Video and Game Controllers. Right click the IDT device and select Uninstall - you should also get a prompt to remove the current driver, tick the box to allow this and then proceed with the uninstall.
When complete, shut down the notebook, unplug the AC Adapter and then remove the battery. Hold down the Power button for 30 seconds. Re-insert the battery and plug in the AC Adapter.
Tap away at the esc key as you start the notebook to launch the Start-up Menu and then select f10 to enter the bios menu. Press f5 to load the defaults ( this is sometimes f9, but the menu at the bottom will show the correct key ), use the arrow keys to select 'Yes' and hit enter. Press f10 to save the setting and again use the arrow keys to select 'Yes' and hit enter.
Let Windows fully load - it will automatically load an audio driver, but just let this complete. Then open your Downloads folder, right click on the IDT installer and select 'Run as Administrator' to start the installation. When this has completed, right click the speaker icon in the Taskbar and select Playback Devices. Left click 'Speakers and Headphones' once to highlight it and then click the Set Default button - check if you now have audio.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience -
New Air Port Extreme and old Air Port Express?
Just got my Air Port Extreme up an running. Is there any reason why my 4 year old Air Port Express would not work with the new Extreme?
The extreme saw briefly yesterday but today the computer doesn't see the express and the extreme only flashes with the orange light showing it has no signal.
Only thing that did change was I did the firmware update on the extreme.
Message was edited by: jcoxWelcome to the discussions!
Connect an ethernet cable from your computer directly to one of the LAN <-> ports on the Extreme. Open AirPort Utility - Manual Setup so the summary page is displayed.
Click on the amber dot and a message will appear with the reason for the flashing amber light on the Extreme. What is the message?
Regarding the Express, how do you plan to use it in your network? -
Air port extreme and windows home server
How do I set up my Airport Extreme to allow me to remotely access my Windows Home Server 2003?
The following are the basics for setting up an 802.11n AirPorts for port mapping/forwarding:
AEBSn - Port Mapping Setup
To setup port mapping on an 802.11n AirPort Extreme Base Station (AEBSn), either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the WHS.
AirPort Utility > Select the AEBSn > Manual Setup > Internet > DHCP tab
On the DHCP tab, click the "+" (Add) button to enter DHCP Reservations.
Description: <enter the desired description of the host device>
Reserve address by: MAC Address
Click Continue.
MAC Address: <enter the MAC hardware address of the WHS>
IPv4 Address: <enter the desired IP address>
Click Done.
2. Setup Port Mapping on the AEBSn.
AirPort Utility > Select the AEBSn > Manual Setup >Advanced > Port Mapping tab
Click the "+" (Add) button
Service: <choose the appropriate service from the Service pop-up menu>
Public UDP Port(s): <enter the appropriate UDP port values>
Public TCP Port(s): <enter the appropriate TCP port values>
Private IP Address: <enter the IP address of the host server>
Private UDP Port(s): <enter the same as Public UDP Ports or your choice>
Private TCP Port(s): <enter the same as Public TCP Ports or your choice>
Click "Continue" -
just installed airport extreme and all iphones are on and good but not my laptop???????? used the laptop to install the wifi then deleted it from my laptop as soon as i had connection on my phones. plese help!!!!!!!!!!
Welcome to Apple Discussions, RipapArt!
Any ideas why this has suddenly happened...
Possibly a corrupted file. If you have not already done so, you might considered booting you computer from the Tiger Install disk, holding down the "c" key. Select your language and then from the Utilities menu, select Disk Utility.
In the left pane of Disk Utility, click on your hard disk. In the right pane, click the First Aid tab and then near the bottom click Repair Disk. If any errors are found, it will try to repair them. Re-run repair disk until it reports zero errors. Then click Repair Permissions. Afterwards, reboot the computer normally. Launch Disk Utility from the Utilities folder and Repair Permissions.
Launch a browser to see if you can get online. If the problem persists, launch System Preferences and then Network. Click Assist me and use the Assistant to create a new location and follow the prompts.
HTH
Maybe you are looking for
-
Safari 5.0.1 hangs, won't load pages. Can you help?
My MacBook Pro w/OS X (10.5.8) running Safari 5.0.1 will load one light-weight page, maybe two, then hangs when indefinitely while trying to load any other page. The status bar in the lower-most left corner says (for example) "contacting www.google.c
-
OracleBIPresentation service in OBIEE 11.1.1.6.2 is not going up.
Hi All, When I deployed the new 11g rpd on OBIEE 11.1.1.6.2 instance its oracleBIPresentation service is not coming up,other services are up. It is giving error like 2012-12-27T06:47:42.000-08:00] [OBIPS] [ERROR:16] [] [saw.security.odbcuserpopulatio
-
"Restrictions Do Not Allow Explicit Content"???
Downloaded a few podcasts yesterday. Listened to one of them on the ride home last night (from my iPhone, after syncing). Tried to pick up where I left off this morning, and these particular podcasts are "grayed out" and, when tapped, say "Content
-
Downloading image without save dialog and saving to disk.
Hi, I'm a bit lost. I have been checking google and documentation and can't manage to do this. I'm using a httpservice, and saving with a file stream the lastResult property. But this seems to be not in binary and when saving it is not correctly done
-
My new ipod touch goes dim after switching on for about a minute?
my new ipod touch goes dim after switching on for about a minute?