Sharing an additional HD on a Network through Apple Share/IP Sharing

Howdy.
I'm trying to set up network sharing on a G5 with OS 10.3.9 for an extra hard drive.
The original hard drive is shared without any problems through Apple Share, but I've installed an additional internal ATA hard drive (on a separate bus) that I want to share but can't.
Is that possible without setting up a RAID? Does the extra hard drive need to be on the same bus as the master drive? Is it even possible to do what I'm hoping?
Thanks in advance for any help.

Try Sharepoints (donationware).
http://www.hornware.com/sharepoints/
John

Similar Messages

  • I used to look my photos in my tv using apple tv, now i can't when i access through apple tv/ computer/ my library  photo option is not available, i check home sharing and which photos i'm sharing from my mac/itunes but i still can share photos w/apple tv

    I used to look my photos in my tv using apple tv, now i can't when i access through apple tv/ computer/ my library  photo option is not available, i check home sharing and which photos i'm sharing from my mac/itunes but i still can share photos w/apple tv

    Morning JJFH,
    Thanks for using Apple Support Communities.
    If after setting up Home Sharing, you cannot access your shared iTunes library over your home network from your Apple TV, take a look at this article:
    Troubleshooting Home Sharing
    http://support.apple.com/kb/ts2972
    Best of luck,
    Mario

  • Accessing my home network through the internet?

    Is it possible to access my home network through the internet via my AirPort Express? I would like to have full access to my Mac Mini's hard drive from my MacBook while at work.

    Yes. You will need to enable file sharing on your Mac Mini (via Sharing in System Preferences) and then you will need to port forward all your ports (since I don't know exactly what file sharing method you will be using) of your Mac Mini via the AirPort Utility.

  • Appletalk network through Linksys seems impossible to set up...

    I wonder if anyone might have an idea why I seem unable to get an Appletalk network set up between my MDD G4 1.25 and my new iMac with Leopard?
    I'm trying to establish an ethernet network through a Linksys Wireless-G 2.4 543 mbps router.
    I've followed all the steps involved... I've set both computers to:
    Appletalk on
    Share printer in the security pane
    Automatically configure the ethernet
    I've loaded the printer driver in both computers.
    But I've had no luck whatsoever with any of it.
    I can't even get the network to show up in the Network Utility.
    I can't get the printer to show up in the add new printer setup...
    I've tried unplugging the router and changing the ethernet cable plug-ins.
    It all sounds so easy in the instructions at:
    http://docs.info.apple.com/article.html?artnum=106658
    Does this sound like a hardware problem?
    I'm totally flummoxed....
    Thanks for any ideas...
    jn

    "Anyhow, I've turned on printer sharing, Appletalk, no-sleep with both machines on and the printer on... and still I can't get any sign of an Appletalk network showing up."
    What sign are you looking for? I think you're being distracted by all this talk about Appletalk. You won't automatically see the disks of the other computers, nor will you automatically see the shared printer from the other computers. Once computers are on the network, which your are if, for example,you can browse the internet, then in order to see each other's hard disks you have to mount them.
    The following describes 10.4; I don't know how much different it might be on 10.5. If I remember correctly, it was much the same in 10.3, but it's been a while.
    On computer #1, in System Preferences, Sharing, it will tell you something like "Other computers on your local subnet can access your computer at ...", and some name will be in place of the ...
    On computer #2, in the Finder's "Go" menu select "Connect to Server." Type in the name you saw in the preference pane on #1.
    If the printer you want shared is on #1, then on #2 you have to go to the Printer Setup utility and look for the shared printer there. In my limited experience, it's not too hard to find a shared printer in the Printer Setup Utility.

  • HT4437 What is difference between air play and home sharing if you just want to show iPhoto's on HD tv through apple tv (just purchased MacBook Air and Apple tv)

    What is difference between air play and home sharing when wanting to show photos on HD tv through apple tv?  Just bought Mac book air and apple tv. 

    You would have to use home-sharing if streaming from a computer. Computer would need to be on and running iTunes.
    http://support.apple.com/kb/HT4352
    Airplay would be useful if streaming from an IOS device
    http://support.apple.com/kb/HT4437

  • How can I know which clients are connected to my network through express and which are connected through extreme?

    I have an airport express extending, through wireless, a network provided by an airport extreme. How can I know which clients are connected to my network through express and which are connected through extreme?
    Here you can see both routers:
    I would expect to some clients connected to the express, other than the extreme. And that's all I see: only the airport extreme appears as client of the airport express.
    Below, one can see the summary of the config for both routers.
    Would somebody explain it?
    Thanks,
    Marcelo
    Message was edited by: Marcelão

    please disregard this answer.
    Message was edited by: Marcelão

  • HT1947 Why can't I see all songs for an artist when using iPad remote for home sharing music through apple tv.

    Why can't I see all my songs for an artist when I search by artist using iPad remote? I'm listening to music via home sharing through apple tv using iPad 2 as my remote. All my songs seem to be listed fine under "songs", but when I select "artist" many of the songs I have for that artist are not there, any idea why that is or how I can fix this.....I suspect it's because many songs may not be associated with an album and it seems only songs in albums are displayed when I search by artist.

    Thanks Ferretbite, but that's not the issue in my case, the songs are not part of a compilation. I just checked several of them and the "Part of a compilation" box is unchecked.....it seems as if the song does not have an album associated with it, it will not display under the artist when I search by artist on the iPad remote which REALLY stinks.
    Hope someone else might have a solution.

  • How to restrict users working on Windows 7 clients from accessing Windows Explorer and other systems in the network through Group Policy with a domain controller running on Windows Server 2008 r2

    Dear All,
    We are having an infrastructure setup of around 500 client computers managed through group policy.
    Recently the domain controllers have been migrated from Windows Server 2003 to Server 2008 R2.
    Since this account requires extremely strict environment, we need to figure the solution for restricting the users from access anything locally.
    It would be great if you can assist me with the following query.
    How to restrict users logged on Windows 7 clients from accessing Windows Explorer and browsing other systems in the network through Group Policy with a domain controller running on Windows Server 2008 r2 ?
    Can we disable Network Tab on the left hand pane ?
    explorer.exe is blocked already, but users are able to enter the Windows Explorer by clicking on the name which is visible on the Start Menu.

    >   * explorer.exe is blocked already, but users are able to enter the
    >     Windows Explorer by clicking on the name which is visible on the
    >     Start Menu.
    You cannot block explorer.exe when you do not replace the shell - the
    desktop you see effectively IS explorer.exe...
    Your requirement sounds like you need a custom shell:
    http://gpsearch.azurewebsites.net/#2812
    Martin
    Mal ein
    GUTES Buch über GPOs lesen?
    NO THEY ARE NOT EVIL, if you know what you are doing:
    Good or bad GPOs?
    And if IT bothers me - coke bottle design refreshment :))

  • Airport express connected to my existing network - Can I connect a device to the network through it's ethernet port?

    Is it possible when my airport express is wirelessly connected to my existing network - to connect a device to the network through it's ethernet port or is it wireless only at that point?
    I'm trying to connect my A/V Receiver in another room to my network without having to run a CAT5 cable all the way to the router.  I'd rather be able to connect it to my airport express if it will work that way.

    Is it possible when my airport express is wirelessly connected to my existing network - to connect a device to the network through it's ethernet port or is it wireless only at that point?
    Yes.....IF
    You have an AirPort Express 802.11"n" version configured to "join a wireless network" and you have enabled the option to "Enable Ethernet Clients"
    Or
    You have an AirPort Express 802.11"n" configured to "extend a wireless network" from another Apple "n" router, in which case the Ethernet port is enabled by default

  • Unable to connect to network through repeater

    Hi
    I Cannot join network through the wireless repeater.  My Iphone 4 works fine next to the router but when I walk downstairs it disconnects.  It can 'see' the repeater as the signal goes to full before disconnecting.  I have tried resetting networks ect but this does not help.  Everytime I put the password in it says 'unable to join network' but works fine if I go near the main router or switch the repeater off.
    It used to work fine untill I got sky on demand. when I connected this through the repeater it seems to have kicked my phone out??  i have since removed the on demand but still cant get my iphone to work.  My girlfriends Galaxy also doesn't get signal through the repeater either.  Any help please

    Hi,
    1 )  try to configure smartview  using xml file as source of  connection:
    <?xml version="1.0" encoding="UTF-8"?>
    <res_GetProvisionedDataSources>
    <Product id="Oracle ESSBASE " name="APS-11.1.2" displayVersion="11.1.2.3.0">
    <Server name="Oracle ESSBASE " context="http://your_aps_server:19443/aps/SmartView"></Server>
    </Product>
    <Product id="HP" name="HP-11.1.2" displayVersion="11.1.2.3.000">
    <Server name="Oracle Hyperion Planning, Fusion Edition" context="http://your_aps_server:19443/HyperionPlanning/SmartView"></Server>
    </Product>
    <Product id="RAFramework" name="RAFramework-11.1.2" displayVersion="11.1.2.3.000">
    <Server name="Reporting and Analysis Framework " context="http://your_aps_server:19443/raframework/browse/listXML"></Server>
    </Product>
    <sso></sso>
    </res_GetProvisionedDataSources>
    2)  You can change EssbasCluster-1 server address using epmsys_registry
    cd C:\Oracle\Middleware\user_projects\epmsystem1\bin\
    call epmsys_registry updateproperty #"Analytic Servers:EssbaseCluster-1:1.ESB"/@host address_essbase_server
    run this command for all EssbaseCluster-1 components
    3) Try to add provider server in EAS console
    4) And check telnet from APS Server to essbase server port 1423

  • I unable to access SDN from my office network through Internet Explorer.

    Hi,
         I unable to access sdn site from my office network through Internet Explorer.
    I can able to access using navigator or firefox..
    Any setting need to be done.
    Cheers,
    Sam

    Hi Sam,
    check you connection settings in IE specially the proxie settings.
    Regards
    Bernd

  • Sending video stream to another network through vpn

    Hello,
    Am christopher from TANZANIA (EAST AFRICAN COUNTRY).
    Please help me.
    we have our cable tv and we want to stream it to our another office in another region, where we have configured a VPN in this two offices using cisco router RV180. I have tried multicast IP but didn't work.
    Please help me how do i send this video signal to another region with our VPN connection. the video is through/output in UDP.
    Any advice please.

    The problem is routing that multicast IP to another network through VPN, and am using RV180 CISCO ROUTER.

  • Need some advice on setting up network through distribution panel

    We just moved into a new house with a distributed wiring panel and I currently have my wireless network up and running. Problem is, I also have ethernet jacks throughout the house that I would like to use for Internet connectivity (the panel didn't include a network module so they just dumped the cabling runs in there). I currently have a cheapo cable modem in the panel, with one ethernet port, and I ran it out to my jack where my Time Capsule is located, so Airport is working fine. Now I need to get some of those other ports working in the house so I can use them for wired connections if I need them.
    I tried using an 8-port switch in the panel. and I get connectivity out to the jacks, but I can't connect to the Internet on our Macbooks. So, I'm guessing I would need to use a router in the panel instead. So my questions are ... Would my Airport network through the TC still work when connected through a router, or would I need to reconfigure a bunch of stuff? And do routers usually require a lot of setup, or are they pretty much PNP? I'm fairly new at this stuff and know about enough to get me into trouble. Thanks!
    Message was edited by: Jimintexas1

    Hi Jimintexas,
    My home is also wired with 37 data jacks and 32 video, with 3 distributed panels( w/16 port gigabit switches) in various areas. My cable modem is also in a different location than the airport. I found that instead of adding routers and such, that as long as I had 2 jacks in the same location, I could connect the cable modem ethernet port directly to the WAN port for the AEBS (TC in your case) by patching the jacks at the panel, and then I connected the LAN port back to any of the switches (that are all connected) through the second jack at the location. I don't know what your distribution panel setup is but chances are it is just 110 punchdowns with standard cable patches so this is fairly easy to accomplish.
    Hope this helps,
    Jamy
    Message was edited by: Jamy

  • I have bought a new laptop and transferred thru home sharing my iTunes. About 1000 songs failed to copy as my new computer said t wasn't authorised. I did authorise the computer and it was 3 of the 5 I'm allowed through Apple. Anybody got a solution plz.

    I've just bought a new laptop and through home share tried to transfer my iTunes library. The new laptop is authored and is 3 of the 5 allowed. About 1000 songs came up as 'computer not authorised', any ideas/solutions/or similar probs.

    Done that and computer is authorised. I click on play on one of the songs that transferred over annotated a 'not authorised to play' and when I click to play I get the 'not authorised' error message, go to authorise the computer and get the message 'already authorised', but still can't play the track. Ahhhhhhhhh!

  • Won't recognize Monitor through Monitor Share

    If I plug my monitor directly into my G5, the G5 knows it's a Dell D1226H. BUT if I plug my monitor into a monitor share, the G5 tries to use some generic monitor extension, and the display is really hard to see.

    We have 2 iMacs and 1 PowerBook, networked through a
    router. Our Epson printer is hardwired to one of the
    iMacs, and printer sharing has been selected and
    turned on in the Printer & Fax preferences of the
    System Preferences. Initially this worked fine, but
    now the PowerBook will not locate the printer through
    the network, no printers at all show up in its
    printer list. We've tried resetting the printer prefs
    in both the iMac and the Powerbook, but still no
    luck. Any help?
    My Epson R200 never did share properly no matter what I did. My Brother works fine as does the Canon950 but not the Epson. My thought is the driver is garbage for anything other than basic, local printing. My next attempt will be my workhorse 1280 and I also have a small USB print server plus a builtin print server on the Airport that I am going to try.

Maybe you are looking for

  • HT201272 I cannot play on my I-Pod Touch recent purchases I-Tunes

    I recently purchases some I-Tunes songs and they will not sync or play on my I-Pod Touch?

  • Problem in Using webdynpro Button outside Interactive Form

    Hi Experts, I am using the WebDynpro SUBMIT button  Outside the interactiveForm My question infact was, that I want to use the WebDynpro native button and place it outside the form. I have written the code in the onActionSubmit() of this button to bi

  • JSP Exception Handler problem

    I have set up an errorPage handler (ExceptionHandler.jsp) for my JSP page, Main.jsp. If the Main.jsp throws an exception from some of its early code, ExceptionHandler.jsp shows correctly. But if Main.jsp throws an exception later on in its code, its

  • I want to use CSS style - background-size:cover;

    in my animation. The responsive settings dont allow for this effect anywhere so I was thinking of putting it in the _edge.js file but, I'm assuming, becasue the Stage is the parent it will fill but distort with the Stage? I've watched the flexible de

  • Touchpad dv6 3030us

    The touchpad on my pavilion dv6 3030 us has never worked correctly. I also can't get the driver/support software website from hp to work. help please!