Sharing internet to wired client using Airport Express
hey
I'm trying to connect a client to my home network through ethernet to a airport express which is wirelessly connected to a Airport extreme base station (802.11n).
This is what i would like my setup to be.
ADSL to modem to Airport extreme wirelessly to Airport Express wired to client (will eventually be a xbox media center).
It says in the apple FAQs that this is possible by configuring the AX as a WDS remote or relay. Since i have no desire to extend the rage on the network, I've made it a WDS remote, but I tried to connect my macbook to it over ethernet to test, which didn't work. Is there any settings that need to be changed it the connection is going to be shared to a wired client?
Thanks
Mike
I have the xact same question as Mcgio. Earlier in this thread there was mention of WDS. From what I have gathered elsewhere, WDS is only necessary if you want to extend your wireless network? That is not what I want to do - I essentilly want to extend my wired network using the AX wirelessly.
I ask about WDS because it does not appear that my Netgear WNR834M router supports WDS (nothing about it in config or the manual).
Will what we are trying to work and what do we need to do?
Similar Messages
-
Using airport express to extend network via ethernet socket
I have a wireless router set up which feeds my mac and tv (via a wired ethernet connection). I have also a pc which doesn't have wifi capability.
Can I use airport express to make my pc pick up the wifi by plugging the pc into the ethernet socket? I would also plug a printer (currently connected to the pc) into the usb, so it can become a shared printer.
ThanksCan I use airport express to make my pc pick up the wifi by plugging the pc into the ethernet socket?
Yes. But, it is the AirPort Express that would "pick up the wifi". Then, you would connect an Ethernet cable from the AirPort Express to the PC.
Configure the AirPort Express to "Join a wireless network" and click the option to "Enable Ethernet clients" during the setup to activate the Ethernet port on the device.
I would also plug a printer (currently connected to the pc) into the usb, so it can become a shared printer.
There is a good chance that your printer will work connected this way, but you won't really know until you try. -
I want to use AirPort Express when I am traveling. I would like to use a wired internet connection in a hotel room to create a wireless connection. However, I do not normally carry my laptop, just my iPad. Is it possible to do this?
You will have to pre-configure the Express using AirPort Utility on your computer before you leave on the trip. The Express will store and remember the settings.
You might want to check with the hotel in advance to make sure that they have Ethernet ports available. Most hotels have switched to wireless and the others are not far behind. -
Using Airport Express with Internet Sharing in Leopard
Howdy all,
I have Internet Sharing enabled on my MacBook Pro running Leopard 10.5.4. I use a Sprint Sierra Wireless Aircard 597E modem to connect to the Internet.
I'm trying to get my Airport Express & Time Machine to recognize my MacBook Pro, or the other way around. Basically, I want to be able to access the Airport Express to wirelessly play music through a pair of speakers and be able to access the Time Machine for backups & accessing files.
With Internet Sharing enabled, my iPhone can access the web, so I believe I have the sharing set up correctly. However, I can't see the Time Machine and my Airport Express just keeps blinking amber.
Does anyone know what I might need to do to resolve this issue?
Any help is so very very much appreciated!Thanks Kappy,
I'm not sure you're exactly following me on this one, though. Here's what I've discovered on my own for anyone else facing the same situation I am:
1. You /cannot/ use Airport Express while using Leopard's Internet Sharing.
2. If you want to create a local network, in this situation, you'll need to use Time Capsule to establish the initial local network, then join the Airport Express into that network. At that point you can use Time Machine with Time Capsule, access it as a hard drive and use AirTunes with the Airport Express.
But you cannot use the Sprint AirCard (and I assume any other similar setup) and your Mac with Internet Sharing to build the local network and then join the other devices to it. Unfortunately. -
Using Airport Express to extend an existing wired/wireless Dlink network
Our network uses a Dlink router which must be located in the basement. Our home office Apple computers are wired, and the wireless Apple laptop is almost always used in the living room, directly above the Dlink, so no signal strength problems there. However, the wireless signal does not reach as far as the home office. It's only 20-25 feet away on the main floor, but for some reason, probably structural, the wireless signal doesn't penetrate.
Now I need to extend wireless access capability to the home office, so that I can use the iPod Touch in the office. I've read through a number of posts, and haven't found one that exactly matches this issue.
The information about joining an existing network has this sentence in it:
"Or you can use AirPort Express or AirPort Extreme to extend the range of an existing AirPort Extreme or AirPort Express network by creating a Wireless Distribution System (WDS)."
The existing network I have isn't an AX network. And it's both wired and wireless. And one of the detailed posts explained why a WDS was not the best way to go. Plus I'm confused by references to "base stations" which seem to refer to something that looks like a Time Capsule, not to an AX.
If AX will do what I want it to, I'm envisioning plugging it (all by its lonesome) in to a wall outlet in the hallway outside the home office. That's based both on what I want and what the salesperson said AX could do when I explained what was wanted.
The Dlink network has been working beautifully for months, and I don't want to do anything to screw it up! That includes even opening up the AX utility software until I know exactly what to do.
Can I do the setup (once it's explained!) on the wired computer? If I have to connect the AX to the network as part of the setup, can I use the 5-port switch that extends the wired connection the extra two feet to the computer (and also provides the wired network connection for the main printer)? Or should I take the laptop downstairs and connect the AX directly to the Dlink router?
Thanks,
Marg+If I connected the AX by cable to my 5-port switch (which in turn is connected directly to the Dlink), would that constitute "an ethernet connection to the D-Link"? If so, then it should be possible to use it as described in your 6th paragraph, to "expand ... (our) main wireless network" -- is that right?+
Yes, this will work great.
+I'd never heard of ethernet powerline adapters, which sound very cool but are not wireless per se - you need a cable to connect the computer with at the far end, and it's wireless capability that I'm trying to create in the home office.+
Rather than hooking a computer up at one end, you could hook up the AirPort Express at one one and setup wireless that way. You won't need the adapters in this case since you have access to the switch. You may have need sometime in the future to get an ethernet signal to another part of the house, so keep this option in mind.
Here is how to setup the AirPort Express. You will use AirPort Utility, which should already be on your Mac Pro. Its located Hard Drive > Applications > Utilities.
Temporarily, connect the AirPort Express (AX) directly to your computer with a short ethernet cable to set it up. When you have the configuration done, you can disconnect the cable and move the AX to the location where it's needed.
Open AirPort Utility and click Manual Setup
Click the Base Station tab below the row of icons to enter a name and device password for the device and choose your time zone, etc.
Then click the AirPort icon in the row of icons at the top of the setup page.
Click the Wireless tab below the icons
Wireless Mode....Create a wireless netork
Wireless Network Name....Exact same name as your D-Link wireless network name
Radio Mode....802.11n (802.11b/g compatible)
Channel...Automatic (see note* at bottom)
Wireless Security...exact same setting as D-Link network
Wireless Password....exact same setting as D-Link network
Click the Internet icon in the row of icons
At the bottom of the page, make sure that the setting for Connection Sharing is set to "Off (Bridge Mode)". This setting allows the AX to work in tandem with the D-Link.
Update to save settings.
*Automatic will usually work well for this. Ideally, you want the D-Link and AX to be on channels that are least 5 channels apart. Automatic will usually choose an open channel, but you may need to manually set the channels on both routers for this step.
Your setup should work fine. Please post back on your progress or questions. -
Using Airport Express for External speakers and Apple TV. When I'm on MAC computer adn using internet sound from Internet does not go through external speakers. Instead it comes out of Mac computer speaker. Why?
As far as I know, the Airport Express only transmits sounds via Itunes. So every other sound (internet, but also incoming mail) will be coming out of your mac instead of your external speakers.
-
Using Airport Express as internet connection for one Mac and one PC
Will probably be judged a complete dork for this question. I have successfully set up my Imac G5 to run an internet connection through an Airport express. My partner runs a PC (Windows XP) and I want to connect this too. Have installed a USB wireless card on the PC, and installed Airport Utility, but it just won't find the Airport Express - it will however find the Imac with something like 96% signal strength. So I set up a network on the Mac and have successfully linked into it with the PC, but it soon comes up with a connectivity problem that will not allow internet browsing. So two questions - can I connect two computers to the Airport Express at once for internet browsing, or do I have to do it through linking the PC to a wireless network? If the latter is the route - any ideas on what the connectivity issue will be? Help!
No, not if the AirPort Express "joins" the wireless network.
No, I do not want to join a network.
It is possible to have the AirPort Express "create" a separate wireless network that would not have access to the Internet, but if you did this, you would need to log off of your normal network....(losing your Internet connection) and then log onto the AirPort Express network when you wanted to listen to AirPlay.
Then, when you wanted to have Internet access, you would have to log off of the AirPort Express network and log back onto your normal wireless network.
Ok, I understand that it is not possible to use airport express only for sound streaming while having an Internet connection at the same time. Airport express does need to join a network if I want sound streaming next an Internet connection. I wanted airport express not to get into way of my Internet connection because in this case the sound streaming messes up sometimes. When I configure airport express only as a sound output, the problems I encounter fade away but then I cannot access to the Internet. Anyhow thanks a lot for the answer. -
I am setting up a used Airport Express. It works fine and my computer can get on the internet whith no problems.
I want to enable my Tivo box to connect to this wifi net, Tivo asks for a Gateway Router number. Where can I find this number?The "gateway" number for your AirPort Express, by default, is 10.0.1.1
-
Currently use Airport Express -1st Generation-to access internet -purchased 2014 Airport Extreme base station -can I import Express back up configuration to keep current settings . Or is it best to do new Airport Extreme as a new Network .
Just spoke with Cisco about the router. They said the router is compatible with the E1500. They suggested that I contact Apple to see if their default IP address was that same as the router (192.168.1.1). They told me I would have to change it if that was the case. How would I do that?
-
Hi I was wondering :
Would I be able to make a local wireless network using airport express that my apple tv can connect to which in turn is connected to a projector with hdmi in so that I can mirror/AirPlay from iPhone pad and macwill the Airport Express allow you to log onto a hotel wireless network, and broadcast a secure wireless network in your room for your wireless devices, like the Ipad, Iphone, etc.?
The bottom line with a single AirPort Express is no.
The AirPort Express can only "extend" a wireless network when the network is being provided by another Apple router.
As you might imagine, it is extremely unlikely that that the hotel network....which no doubt uses professional wireless access points provided by a manufacturer of commercial systems.....would be compatible with an AirPort Express.
In many years of travel domestically and internationally, I cannot recall a time when a single AirPort Express would "extend" the signal provided by a hotel's wireless network.
However, if you had two AirPort Express devices handy, you might be able to configure one to "join" the hotel network and provide an Ethernet signal to the second AirPort Express, which would be configured to "create" your own "private" wireless network. -
Using Airport Express without a modem
Can you set up a wireless network using Airport Express without a modem? I want set up a wireless network at work. Can I just plug in the ethernet cable on my desk to Airport Express for it to work? Thanks.
Hello Low77. Welcome to the Apple Discussions!
Can you set up a wireless network using Airport Express without a modem?
Yes. By default, the AirPort Express Base Station (AX) will create a stand-alone wireless network which you can connect up to 10 wireless clients for file or printer sharing.
Can I just plug in the ethernet cable on my desk to Airport Express for it to work?
You do not need to plug it into an Ethernet cable for it to work. However, if you require network or Internet access, the Ethernet cable needs to be connected to a network or have Internet access. -
I have a MacPro 2008 workstation. It has no Airport/Airport card so I have to use an ethernetcable to connect to my modem. As the MAcpro
is in my office in the attic and the wireless modem is in the basement I have a problem. I wonder if it is possible to use Airport Express to connect to the wireless network? Itshould be like this: in my office I connect the MacPro with AE through an ethernet cable. If I can then get AE to connect (wireless...) to my wireless network I should be ablle to connect my MacPro to internet/wireless network. Is this possible???? Any suggestions are very much appriciated. Thank you.Apple calls this configuration a ProxySTA.
To activate ProxySTA, you must set up the Express to join a wireless network and then enable the Allow Ethernet Clients setting; both settings are located in the Wireless tab of AirPort Utility. -
How can I share my Internet from my iPhone to Airport express network?
How can I share my Internet from my iPhone to Airport express network?
YES you can! - Gotta love those "you can't" answers from people who haven't even tried. ;o)
Just have your Airport Express "Join" your iPhone. It will share your Internet connection through its Ethernet port. I currently have an AppleTV connected via Ethernet to the Airport Express. With this setup I have wireless Ethernet AND wired LAN connection. I can even AirPlay to the AppleTV and have Internet at the same time. Haven't tried a switch/hub but see no reason why it wouldn't work. This proves to be very useful to create a wired network with Internet from a cellular device without Ethernet. -
Wireless to ethernet connection using airport express
Here is what I have and what I wish to do. I have a Mac Mini intel duo with Airport extreme card Connected to road runner via a ethernet router. My wife has a window running XP with out airport extreme. Can I use airport express to share the internet with my wife's computer by using an ethernet cable from my wife's computer to the airport express, remotely to (another room). Utilizing my computer as a base station?
Fordmanduo, Welcome to the discussion area!
No that will not work.
The Ethernet port on the AirPort Express (AX) is active ONLY when the AX uses WDS to wirelessly connect to a network.
OS X's Internet Sharing (via Mac mini) is not compatible with WDS. -
I currently have a D-Link DI-604 broadband router with windows computers. How can I add wifi to the network for use with ipad? Can I use AirPort Express?
Yes. You can directly connect an 802.11n AirPort Express Base Station (AXn) using an Ethernet cable. The AXn would then just need to be configured as a bridge to allow the D-Link to continue to provide both NAT & DHCP services for all network clients connected to either router.
In this configuration, the AXn would broadcast a wireless network for your wireless network clients to connect to.
Maybe you are looking for
-
My new macbook pro retina recognizes, but can't transfer data from the Time Machine Volume
I back up my old 2008 MacBook Pro to a Time Machine volume sitting on a very new 2 TB drive that is connected to a Time capsule via USB. I got that new drive from OtherWorld Computing about 2 months ago. I just received a brand new 2012 MBP (retina).
-
Problem in Long text save in CO02
Hi All, I am posting long text for a production order using 'CREATE_TEXT' and its updating in the tables succesfully. The same old probelm is it is not appearing in the CO02 or CO03 tcodes. I did a direct AUFK-LTEXT update as suggested in many of the
-
Savings play counts/dates added?
Hi, I'm going through the process of re-installing Windows XP on my computer, which means I'll have to back up all of my music on CD's, but I really want to keep my play counts and my dates added for my music when I add it back to the computer...is t
-
I am having trouble downloading my creative cloud, the app keeps closing on me
my creative cloud app fails and closes everytime i try to launch it. Please help me
-
Modifying ALDSP data source end points programmatically
I can see how to manually modify ALDSP data source end points through the ldconsole: http://edocs.bea.com/aldsp/docs21/admin/server.html#1042064 but is there any programmatic way to do this? For my purpose, it would be adequate if there were some Ant