Shift+control+A conflicts between FF4 and blogger: When I want to create a hyperlink, the add-on tab opens.

Blogger has long used Shift+Control+A as the keyboard command for inserting hyperlinks. Now that I've switched to FF4, I discover that it's also the command for opening the add-ons tab. I can still create a hyperlink but every time I do, I have to close the add-on tab. This is a nuisance when writing a link-heavy post. Since I blog regularly on several different Blogger pages, the annoyance factor is growing regularly.
I checked the Keyboard Shortcuts page and read, "Firefox does not provide any method of customizing keyboard shortcuts." Is this absolute? If so, I suggest deleting or changing the FF4 hotkey since Blogger has years of precedence with this command.

Scott,
You don't need to use a digital line to create a TTL pulse. The PCI-6025E has two onboard general purpose counters. You can use one of these counters to create a single pulse of the desired pulse width. For an example of how to program the counters on your board, refer to LabVIEW's Search Examples>>I/O Interfaces>>Counters>>Pulse Generation>>DAQ-STC based.
The advantage of using a counter over the digital line is that it allows you to control the timing of the pulse through hardware and not software. Thus, it is inherently faster, and the timing resolution is more accurate. The counter will count down an internal 20 MHz timebase to create the pulse delay and the pulse width.
For more information on the hardware capabilities of your board, you can refe
r to the User Manual online at www.ni.com/manuals.
Hope this helps.
Regards,
Erin

Similar Messages

Error while trying to synchronize audio and MIDI. Sample rate 42804 recognized. Check conflict between Garageband and external device.

Sometimes, while playing back my software instrument songs, I get an intermittent pop-up error message, saying "Error while trying to synchronize audio and MIDI. Sample rate 42804 recognized. Check conflict between Garageband and external device."
(Sometimes the five digit number is different, but remains a five-digit number beginning with "4".)
Simultaneously, the song stops until I press the "Okay" button in the pop-up window.
When I continue to play the song, the sound is jerky and clipped, and the playhead doesn't keep up with the song, and then suddenly jumps to the part of the song currently being played.
There's also a sound of static.
The issue seems to occur whether or not I have my MIDI controller turned on and plugged into my desktop Imac.
Tony

Hello,
open your Audio MIDI Setup utility and set the input to 44100
https://discussions.apple.com/message/12710638#12710638

How can I resolve conflict between itunes and Windows 8.1

When downloading itunes to my laptop computer, using Windows 8.1 my email/network account will not work on that computer. It is fine on other devices such as ipad and Windows phone. I can also pick up emails on online on the same laptop. There appears to be a conflict between itunes and Windows 8.1

Please see Boot Camp for comments.

[JS CS3] Conflict between palettes and panels

Hello,
I am having a conflict between panels and palettes. Hopefully I can get some direction without having to copy the code here, because it is very long.
I have a window of the palette type. This palette has buttons and radio buttons. The buttons call up various functions.
The radio buttons, however, make visible/invisible a series of panels in the palette. The panels are stacked upon each other, only one of which is visible at any one time, depending upon which radio button is selected.
One of the buttons in the palette calls up another palette (which also has a series of buttons for various functions). Let's call it the little palette. The problem is, that after the little palette is called up, the radio buttons in the big palette no longer work. I can select them but they will not make visible/invisible any of the stacked panels. The buttons in the visible panel work as well as all the other buttons that are always visible. The only thing that does not work are the radio buttons.
My only workaround is to just dismiss the palette and call it up again. But I'd rather fix this bug.
Any ideas? If I need to I can strip down the coding leaving only the essentials, but rather not take the time if this is a problem others have run into and hopefully have a solution for.
Thanks,
Tom

Thanks. I'll give it a try, but I even uninstalled both programs, tried
reinstalling Reader only, and when that didn't work, uninstalled Reader and
then reinstalled Acrobat. Still a problem. The particular website is
www.officeally.com, and it opens the PDF file in a browser window, I believe
using an ASP file.
Larry

Name space conflict between static and instance method

Hello,
there seems to be a very unfortunate name space conflict between static and instance method name. Consider:
static String description() that should return a description of a class.
String description() that should return a description of an instance.
That seems to confuse the compiler. How come? Static and instance methods don't have anything to get confused about.
Thanks for any insights :-)

Umm...jeez.
It's not a bug, it's the way it's supposed to be.
Since a static method can be called the same way an instance method
A instance = new A();
A.staticMethod();
instance.staticMethod();it's not allowed.
Also in the class, you can call
public void myMethod() {
instanceMethodInClass(); // You don't need this, it's superfluous
staticMethodInClass(); // You don't need the class name.
}If you didn't understand, then just accept the fact that it is so. Some day you'll understand it.

Metadata Conflicts between LR4 and CS6

I recently upgraded to LR4 and CS6 Extended. I will offer start in LR4 but switch to CS6 for additional editing. On some of my thumbnails, I will see a "!" in the upper right hand corner on the thumbnails. When I click on the icon, a pop-up window appear stating a Metadata conflict has occurred. The pop-up window gives you two options: Copy file data into the catalog or have the catalog overwrite the file data. What is the best thing to do knowing you are only working between LR4 and CS6?

This is a known issue with the latest PS update. Refer to the pertinent thread on the PS forum.
Mylenium

Software conflict between iPhoto and Sony MP3 player

I am experiencing a major software conflict between iPhoto and my Sony MP3 player (model: NWZ-E443). In the past, whenever I connect the MP3 to my 2009 MacBook Pro, iPhoto always opened. I would simply close iPhoto and everything would be OK, though. But after upgrading iPhoto a few months ago via an upgrade download I am now unable to view images full-screen. Although thumbnails display OK, when I double-click on any of them to display full-screen, the MP3's 'Do Not Disconnect' image displays full-screen instead, even when the MP3 is not connected.
I have tried reinstalling iPhoto from the original iLife disc, but this didn't work and my fear is that the Sony software has somehow corrupted every image single file in my library.

Turns out my Mac put code on the mp3 player because after I reset the mp3 player to its 'factory settings', (erasing everything) it went back to normal and now shows up in the finder window.

Conflict between VPN and Airport disk

Hello Folks, I just bought a brand new airport extreme 802n.
I thought it would be working fine with my Macbook pro, but it doesn't.
I can't access any externe hard disk or USB Stick through the airport extreme, although the format is FAT32. I checked and checked but found nothing useful. All the settings are default.
Worth to mention, I always use a cisco VPN client to get connected to the Internet (university student).
There are few times when I disconnected the VPN Client, the USB Client can be found and read, but not be written.
I though it is a conflict between VPN and Airport disk. So I tried without VPN, but the USB stick and the extern hard disk still didn't work properly. I have no idea what is happening could somebody help?
By the way is it possible to set Airport extreme as a VPN router so I don't have to use the cisco VPN client anyway?
Any reply is appreciated
Thank you !

I have an Airport Extreme connected to a cable modem
with comcast as my isp. The Extreme is connected to
a G4 dual processor mac via ethernet. I also have 3
airport expresses around the house to work as range
extenders. When I had the G4 connect to the Extreme
via its internal airport card, I had no difficulty
connecting to any of the Expresses around the house
with my g4 powerbook. Now that I have the G4 Dual
directly connected by ethernet to get the fastest
speed, I cannot get my expresses or my laptop to
connect through my laptop to the base station. all
lights are green on the expresses, but running
network diagnostics on the powerbook shows red or
yellow for the last two buttons on the right. Do I
have a configuration problem or an Extreme that won't
bridge properly?
Check that the G4 Dual has a location configured with
only "Built-In Ethernet" activated, and that its
Ethernet connection isn't shared on AirPort.
Turn off all your AX and check that your
PB G4 is able to connect to "your" AirPort network.
Take advantage of this silence of all your AX
to run an analysis of your wireless environnement:
- check that you don't have any neighbor wireless
network,
- check that on each of your AX settlement you have a
very good reception of "your" AirPort network.
If everything works fine to that point, add one AX to
your network, and check the reachability of your network
where you wanted to extend it.
dan

Hi - I'm trying to sync iBooks on my Macbook Pro with iBooks running on my iPad. I have some pdf's download from the net I want to share between devices and I can't work out how to sync the two devices. Any help please?

Hi - I'm trying to sync iBooks on my Macbook Pro with iBooks running on my iPad. I have some pdf's download from the net I want to share between devices and I can't work out how to sync the two devices. Any help please? I'm running Mavericks

Thanks for your help Brij011 - much appreciated. Apologies as I'm a newbie but I've looked at the info for synching and I appear to have all the switches flicked on my iPad. Does the iPad and iBooks only sync in iCloud for purchases as I appear to be doing something wrong. I could sync ok when books was in iTunes but since migrating to Mavericks I think I'm doing something wrong!!

In Mountain Lion how does OS select between ethernet and WiFi when both are activated??

In Mountain Lion how does OS select between ethernet and WiFi when both are activated?? How does OS use "both" networl accesses??

It will pick the highest service in the list which has an internet connection.
To order the list, open Network System Preferences and select Set order of network services from the button below the service list.

I am working in my itunes and removing duplicates. When I go to delete a series of items then I press the shift button highlight and delete; when I want to delete several that are not in a series I go to use my "fn" button, it wont work

I am working in my iTunes removing duplicates. When I want to remove a series of duplicates I hit the shift button on the key board, highlight and delete; when I want to select several to delete but are no in a series in the past I would hit the 'fn' button then highlight and delete. That button does not seem to be working at all. Any insight would be appreciated. Thx

Command-click does the trick.

What are the configuration need between R3 and XI when we use RFC sync adap

hi,
What are the configuration need between R3 and XI when we use RFC sync adapter.
Regards
siva.

if its the sender adapter ref:
RFC adapter
Sender- /people/michal.krawczyk2/blog/2005/03/29/configuring-the-sender-rfc-adapter--step-by-step
Receiver;
http://help.sap.com/saphelp_nw04/helpdata/en/c8/e80440a832e369e10000000a155106/content.htm
Also;
trouble shooting rfc/soap -
/people/shabarish.vijayakumar/blog/2008/01/08/troubleshooting--rfc-and-soap-scenarios-updated-on-20042009

Powerbook alternates between battery and adapter when plugged in

The other day my PB started alternating between battery and adapter when plugged in: the symbol changes from batt to charging every few seconds, brightness goes up and down. I've managed to find a position where it will actually charge. I even tried a new adapter, but it's still extremely temperamental.
I'm afraid there's something wrong with the internal power jack, but is there anything else it could be? Any way to tweak the jack?
Thanks!

No, there's no way to "adjust" the port. It's soldered to a small Sound/DC-In card inside the Powerbook. What's apparently happened to yours is that the cord has been jerked rougly up, down or sideways one time too many, and one or more of the solder joints has broken. Because it's now able to move, however slightly, the rest of the joints are also being stressed every time you connect or disconnect the cord. Sooner or later another will break, then another. You'll end up having to replace the card when you can no longer shim or jimmy the port so it makes proper contact.
If you're very good at very small-scale soldering, you could take the card out and try to repair it, but if you're an average ham-handed Joe like me, replacing the board is a better bet. Getting to it, while not actually difficult, is a pretty considerable adventure in an Albook, because nearly everything else has to be removed from the case first to reach it.

How does iPad choose between wifi and 3G when both are 'on'?

Easy peasy question.
I have 02 and Wifi going on my iPad. I know I can use 02 out and about and I know I can use wifi at home etc.
But when I'm at home how do I make sure I'm using my wifi for data and not my cellular connection???
I've been turning my cellular to 'off' when at home, just in case, but I don't want to have the faff of turning it off and on, so it would be nice to know how the iPad chooses between wifi and 3G when both data access points are active.
Also I've had no wifi troubles at home at all. so far... The acid test will be setting it up at work as they have proxyies for everything, but obviously I don't have proxies at home. I'm not sure if the settings screen can cope with different proxies dependent upon different wifi networks... * grin *

In the status bar I have
a signal strength indicator then 'O2-UK' then the 'fan' No mention of 3G.
I'm guessing you're going to say that when 3G is showing then 3G is being used for data?

Difference between CS3 and CS4 when placing images, percentage not kept

There is some kind of difference between CS3 and CS4 when placing images. The images I've dealt with right now were vector images but it might apply to all kinds of images.
When replacing an existing image, the CS4 behaviour is to let the image fill up the frame. In CS3 the percentage was set to 100% as default (the % you see when selecting the image, not the container).
Also when replacing an impage in CS4, the "inner" image frame is kept, while in C3, the percentage was kept.
Is there some kind of placement preferences / settings to let CS4 act the same wat as CS3 did, when placing an image?
-- Andreas

Yes, the behavior was changed in CS4 (and many users, like me, prefer the new system).
If you click and drag a loaded image place cursor the entire image will be be scaled to fit the proportionally drawn frame -- a huge timesaver if you mostly place uncropped art. If you want 100% of the image at 100% scale, just click and release -- same as before, or as before you can pre-draw a frame and place into it and your image will come in cropped at 100% (unless you've changed the fitting options for the frame before placing).
Peter

Shift+control+A conflicts between FF4 and blogger: When I want to create a hyperlink, the add-on tab opens.

Similar Messages

Maybe you are looking for