Should an ISDN Primary Rate port adapter be recognised when installed in a 7206VXR

The 7206VXR does not recognise the Primary Rate port adapter and the controller E1 command cannot be issued. The router has an NPE400 installed and is running 12.1(6)E. Is this an invalid hardware/software combination, if so what level of IOS should be used?

These are the following which are not
supported:
PA-CT1/PRI
PA-CE1/PRI-75
PA-CE1/PRI-120
The reason for this is described here:
http://www.cisco.com/warp/public/770/fn3028.shtml

Similar Messages

  • Can you specify the port for default services when installing OEG?

    Hi everyone,
    The default installation of OEG 11g uses 8090 port for management services, and 8080 for the virtualized services that you register in the gateway. After installation, you can change the ports by editing gateway's Profile Repository in Policy Studio. But is there a way to specify the port number before/during the installation?
    Thanks,
    Iris

    Hi -
    here are the steps to change the listening port (in 11.1.1.6)
    - Connect to OEG using Policy Studio
    - Click on "Edit Active Configuration"
    - Under "Services", find the default services, and you'll see a listener for port 8080 there. Right-click to edit this.
    - Change the port from 8080 to your desired port. Note that if you've installed the software and running it as a non-root user on Linux, then it will not have permission to bind to a low-number port (like port 80 for instance)
    - Now deploy your change (for 11.1.1.6 hit F6 or click on the "deploy" button which is towards the right of the toolbar in Policy Studio).
    - You may also choose to version your configuration at this point (click on "version" which is beside the "deploy" button and enter a comment about your version).
    Now verify that OEG is listening on your new port. You can see it bind to the new port by looking at the trace [Connect a browser to port 8090 on OEG, login as admin or another user who has rights to view the trace, then click on "Trace"].
    It's a usual practice to configure a new listener on SSL (e.g. on port 443) then to delete that pre-configured port 8080 listener, if you want to only receive traffic over SSL.

  • Adapter configuration Failed when installing BODS 3.1

    Dear All,
    I am trying to install BODS 3.1  on windows 8 pro laptop and I have got an error,"Adapter configuration Failed" .
    What will be the issue?
    Regards,
    Kathir

    Dear All,
    I am trying to install BODS 3.1  on windows 8 pro laptop and I have got an error,"Adapter configuration Failed" .
    What will be the issue?
    Regards,
    Kathir

  • TS2002 using a multi-port adapter to increase the number of USB ports - affects system functioning?  Port priority?  In advance, I send my thanks!

    Hello.  I've never "started a discussion" before.  Ah well I've always had good luck with the communities so here goes.  Today I plugged a Belkin multi-port adapter into my MacBook Pro running OS X Version 10.6.8  This enabled me to plug in my keyboard; mouse and printer.   Yes after two years I wanted to be back to an independent full keyboard and mouse.  BUT ALAS!  Now the little spinning wheel keeps appeariing while I'm on the Internet and I learned through my "Help" app that I have "slow start-up, pausing at Initializing network or "Configuring network time"  (sounds like some of the men I've dated).
    Could it be the multi-port adapter?  Should I use a different model?  The abiltiy to have the printer; keyboard and mouse all connected at the same time is important to my work. 
    In advance, I send my thanks!
    Jeannie-Marie

    I think it is the server socket which controls the number of client sockets to be opened. The number of connections that are accepted by the server socket is called the backlog of server socket. By default its value is 50. (See java.net.ServerSocket class in java docs)...
    we can specify the backlog in the constructor of server socket...
    ~pacific

  • Female Mini Display Port Adapter - Connect Monitor to Non Mini Display Port

    Anyone know of a Female Mini Display Port Adapter, so I can connect the 24 LED Cinema Display to a computer that has DVI connector? Or hook the monitor up to a KVM, so I can use the monitor with multiple computers?
    I know Apple doesn't make these, but does a third party?
    Monoline appears to be coming out with adapters to hook a mini display port computer to DVI and HDMI, but not a mini display port monitor to DVI or HDMI.

    'Mini Display port' is just a smaller version of display port, which is a slightly different version of HMDI.
    No. You may be thinking of Mini DVI. Mini DisplayPort is a smaller verion of DisplayPort, which is different from DVI and HDMI.
    <http://www.displayport.org/white-papers/whitepapers/DPTech_OverviewEnglish.pdf>
    HDMI, display port, mini display port AND DVI are all capable of being 'converted' from one to another.
    It is easy to make a Mini DisplayPort (card) to DVI (display) adapter because a DisplayPort card can be set to generate DVI signals. (Dual-link DVI is a bit more complicated since the adapter must sepatate the clock and data.). A DVI card cannot generate DisplayPort signals, so an adapter for a DisplayPort display with a DVI card would be a lot more complicated.
    The ONLY thing that you would LOSE in a DVI to display port conversion is an audio signal.
    HDMI is DVI video plus digital audio. DisplayPort does not use DVI video.
    The point is they are all interchangeable, signal wise.
    No. A DisplayPort card can generate DVI signals when a DuisplayPort to DVI adapter is detected, but a DVI cards cannot generate DiusolayPort signals.
    But why should Apple make a cheap DVI to female display port when they can make more money on overpriced graphics card upgrades?
    They can't make a cheap adapter, but they could have added a DVI port to the display.

  • NME-CUE Port adapter is disabled

    Hi Guys, in need of a little help, i'm trying to install a NME-CUE into a CISCO3845 but the card is showing as disabled
    Installed  c3845-spservicesk9-mz.150-1.M10.bin and PVDM2-64
    Slot 1:
            Integrated Service Engine Port adapter, 1 port
            Port adapter is disabled
            Port adapter insertion time unknown
            EEPROM contents at hardware discovery:
            Hardware Revision        : 1.0
            Part Number              : 73-10371-02
            Top Assy. Part Number    : 800-29801-01
            Board Revision           : A0
            Deviation Number         : 102999
            Fab Version              : 01
            PCB Serial Number        : FOC13232JXF
            RMA Test History         : 00
            RMA Number               : 0-0-0-0
            RMA History              : 00
            Product (FRU) Number     : NME-CUE
            Version Identifier       : V01
            CLEI Code                : IPUIA6NRAA
            EEPROM format version 4
            EEPROM contents (hex):
              0x00: 04 FF 40 04 F8 41 01 00 82 49 28 83 02 C0 46 03
              0x10: 20 00 74 69 01 42 41 30 88 00 01 92 57 02 01 C1
              0x20: 8B 46 4F 43 31 33 32 33 32 4A 58 46 03 00 81 00
              0x30: 00 00 00 04 00 CB 87 4E 4D 45 2D 43 55 45 89 56
              0x40: 30 31 20 D9 03 40 C1 CB C6 8A 49 50 55 49 41 36
              0x50: 4E 52 41 41 FF FF FF FF FF FF FF FF FF FF FF FF
              0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
              0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
    any ideas on where to go from here
    Many Thanks

    It seems like issue with the CUE. But lets work it out step by step:
    1) If you haven't configured the Router\CUE interface, please enable it and try to access CUE or check the CUE status from the router CLI. Here is a quick reference guide:
    http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/unity_exp/rel7_0/install/Install/nuinstall.html
    Do not forget to configure static route pointing CUE ip address to the CUE interface.
    Let me know whats the output.
    2) If nothing helps in step 1, your only option would be to reseat the CUE module and try in a different slot. Make sure to reboot the router. (as I think its not hot swappable)
    3) If nothing above helps, then most probably time for RMA.
    Apart from above, was it a working setup or you bought it second hand?
    Can you also post an output of sh inventory?
    -Terry
    Please rate all helpful posts and mark the thread as answered if you have no other queries.

  • Port adapter gigabit router 7204vxr npe-400

    Hi, I want to find a gigabit port adapter to my router. I found pa-ge port adpater but this port is for fiber link and I want a gigaport adapter for copper not fiber and I do not find that. Anyone knows a gigabit port for copper?

    Disclaimer
    The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
    Liability Disclaimer
    In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
    Posting
    BTW, often "fiber" (e.g. SFP) ports support copper modules.
    As others have noted, a NPE-400 is rather underpowered to support gig ports.  (Wirespeed gig, for minimum sized Ethernet, in just one direction, requires up to 1.488 Mpps, or about 3 Mpps for full duplex.  Consider a NPE-400 offers 400 Kpps, a NPE-G1 1 Mbps, a NPE-G2 2 Mpps, and a NSE-1 3.5 Mpps.)

  • Why my new Mac mini  DVI dual link mini display port adapter doesn't work  with my 30"display (LG W3000H)?

    Hello There
    Can any of you advise on the below? Tried to connect Mac mini with a 30" display through a DVI dual link mini display port adapter. For the first try Mac mini go connected to the display, then i've chosen the highest resolution (2560x1600, native) and right at that moment they got disconected. Since then the display stays black. What can be the issue, is it possible DVI dual link mini display port adapter is not compatible with 30"display (LG W3000H)? It works with DVI male-male cable plus DVI HDMI adapter as long as the resolution stays under 1280x800. Any idea is much appreciated.
    Thank you, Vera

    Hi,
    I can report that my Mac Mini Intel Duo connected instantly and without even having to set it up (on the first try) with my 1366x768 native resolution DELL 50" Plasma Display. It's so beautiful that I just want to stand there and fondle my HDTV as I drool haplessly like Homer Simpson with a doughnut in his mouth. Seriously, no problems.... guess I bought the right cable (ebay).
    Before you buy a Duo, make sure you're aware of the airport and bluetooth issues that so many (maybe everyone who tries to use them together) are having. It seems that bluetooth interferes with airport, or maybe the other way around. Anyway, it's messed up. Also, Airport reception is generally VERY poor with the new Intel Mac Mini.
    Despite these things, I still love mine (I now have 2 base stations and an airport express for my powerhouse wireless needs, and an external DLink bluetooth-2-USB dongle solved the bluetooth/airport issues... in my case).
    FWIW,
    awk
    667-MHz Ti PowerBook G4.   Mac OS X (10.3.9)  

  • HT4241 How do I get an Epson EX5210 to display using the HDMI mini display port adapter so I can see 1080p downloaded movie from iTunes? It won't recognize the display via hdmi cable and adapter!

    Please help! I've tried everything to get this dang thing to display a downloaded movie from itunes on my epson EX5210 lcd projector via a HDMI cable plugged into a minidisplay port adapter. I am no expert and have no idea what to do!

    It's all in the manual... starting on page 26...
    USB seems to work as well. Tried that?
    By the way, this dang thing has "only" 768 physical pixels vertically, so "1080p" won't be visible anyway, and scaling will take place. Hope you won't be diappointed. All specs including resolutions here.

  • External hard drive not working in USB multi-port adapter

    Hi,
    I was wondering if anyone had a suggestion...I got a new My Passport Essential portable external hard-drive. I have a Belkin multi (4) USB adapter and when I plug the hard-drive in, it won't recognize it. It only works if I directly plug it into one of the two USB ports on my computer. Does anyone know of a USB multi-port adapter that would have sufficient power for me to plug my hard-drive into it? The cord is too big and bulky to plug it into my other USB port on my laptop with the adapter in place, so I either have to get another adapter or try another external hard-drive.
    thank you! Robin DySard

    Hi UKPOL,
    Please refer to this How to Geek article.
    Win 8.1 no longer supports a graphical interface for backing up files or creating system images. You must use powershell or Win 8.1's reset/refresh options.
    You can also create custom refresh images. Please see this article. The instructions also work with Win 8.1.
    You would have to use third party backup software for backing up files and folders.
    Jaco
    ****I am not an HP employee****
    Please give a" Kudos" if advice received is relevant or" Accept as Solution" if your problem has been solved.
    +++++++++++++++++++++++++++++++++++++++++++++++++++++
    H8 1380t CTO, Intel i7 3820
    16 GB DDR3
    Pegatron Motherboard- IPIWB-PB (Pittsburgh), Radeon HD 7570 1GB. Win 7 Home Premium upgraded to Windows 8.1 Pro.
    Envy Phoenix 810-150se, Intel i7 4820k
    12 GB DDR3
    Pittsburgh2 Mainboard, NVIDIA GTX 645- 2GB GDDR5. Win 8.1 Pro.
    HP 560z CTO AMD Phenom II X6 1090T
    16 GB DDR3.
    Radeon HD 6570
    Win 7 Home Premium upgraded to Win 7 Pro.
    HP ENVY 17t-j000 CTO Quad Edition Notebook. I7 4702mq
    12 GB DDR3
    Nvidia Graphics
    Win 8 Pro
    Errare humanum est.

  • After 1 year earned leave should generate and pro-rata quota should generate next year on jan 1st.

    Hi Experts,
    Here is the client requirement and please let me know how to solve this.
    Earned Leave: after 1 year earned leave should generate and pro-rata quota should generate next year on jan 1st.
    Example: if employee joins on 01/07/2012 after 1 year i.e 01/07/2013 quota should generate 22 days next year on 01/01/2014 pro-rata quota i.e 01/07/2013, 11 days pro-rata quota should generate. Total 22+11 =33 have to generate on 01/01/2014. and next year 01/01/2015 (22+11+22)=55.
    Note: on 1/7/2013 = 22 days
    on 1/1/2014 = 11 days +22 days; total=33
    on 1/1/2015 = 33 days +22 days; total=55
    Conditions: if employee joins before 15th date of current month include the current month, if employee joins after 15th date exclude the current month.

    You will need 2-3 PCRs to address this.
    In one PCR you need to query the Date of Hire (from IT0041 - I guess you are maintaining this) using HRS=YDAYxx - where xx is the date type. You can then check it it is the first year anniversary or not by using HRS?01. If the condition satisfies populate a custom time type with 22 days.
    In another PCR, you need to check for 01 Jan by using HRS=BCURMO and HRS=BCURDY. In this PCR check again the length of service (see above). If it is more than 1, then proceed to give the pro-rata amount.
    If the pro-rata formula is simple you can use the second PCR or you would need a 3rd PCR to get the pro rata amount. Using HRS=Y**** operator you can query many date differences which will help.
    Regards
    Pramod

  • Parallel port adapter in labview

    I have usb to parallel port adapter . After plug it into my laptop some drivers installed automatically and it is detected in device manager as "parallel port printing support" under "universl serial bus controller".
    I know how to write data to serial port using visa write funtion but, i dont know how to access this adapter from labview 2010
    i am using windows 7.
    Can anyone help me in this regards.
    Thank you

    Please stick to the original post. Thanks.

  • Best display port adapter?

    Just got a nice new matte T410s, and I need to get appropriate hooksups for my HD Computer Monitor (w/hdmi) and TV.
    I see that a lot of the adaptors don't transmit sound.   I have the discrete nvidia card, which I have read can in fact transmit sound.  
    What is the best value display port adapter to HDMI and/or DVI? 

    there are a lot of displayport to hdmi adapters on the market, the difference between them in actual functionality perspective is not that much.
    My recommendation is to get a cheap one from ebay or amazon, etc.
    Regards,
    Jin Li
    May this year, be the year of 'DO'!
    I am a volunteer, and not a paid staff of Lenovo or Microsoft

  • Should I block TCP/UDP ports 135 to 139 on my router?

    For the sake of Internet and Desktop security should I block TCP/UDP ports 135 to 139 both ways at all times on my router?  This seems to be recommended for Windows environments. Does Mavericks need these ports for its proper operation?  When tested, ports 135, 137,18 show as closed whereas all other ports are Stealth.  Ideally, they should all be Stealth.

    Have a read here: http://securityspread.com/2013/07/26/firewall/
    Stealth is just as good as closed, some would argue that stealth is just as much of a giveaway of the port being present as it being closed.
    The specific ports you mention pose no risk to OS X as far as I am aware.

  • Exchange rate should be a fixed rate instead of the updated financial rate.

    For import and reconciliation purposes the used exchange rate should be a fixed rate in stead of the updated financial rate.
    Customer want to use  u20AC 1 = $1.25 from now on as fixed rate for products validated in Euro in his system to convert into USD on  commercial invoice and or shipping invoice for shipments going into the US.
    Thanks in advance
    Jeewnath

    What is the exchange rate type used?  I think we can do it by exchange rate type M.
    Thanks
    Krishna.

Maybe you are looking for