Should either one ethernet or coax broadband always be connected in an actiontect 424 rev.g?
I was reviewing the Verizon FIOS post titled "Entering DNS settings in the Actiontec MI424WR router to opt out of DNS Assistance", when I noticed a difference with my actiontect 424w rev g settings. In my case, I do not have any broadband connection with the status "connected", either the coax or the ethernet. My fios setup uses coax from the ONT (Verizon installation) to the router. I have disabled the wireless router section and use an apple airport capsule for the wpa wireless. I also have a couple of actiotects in bridge mode for providing ethernet ports to two tivo boxes and a desktop. Everything works but I wonder if by miracle not by design...Based on my reading, if the coax input is connected to the actiontec, then by definition the connection to the internet is via coax to the ONT, and the settings should indicate a "connected" broadband connection. Am I correct? I have assumed that the other two bridges are neither the network controller for my installation. TY for the help
Hope this is of help to you.
M1424WR Rev F with WPA2
From Traffic Monitoring screen on Router
Netwrk(Home Office),Ethernet,Broadband Connection(Ethernet),Coax,Wireless Access Point...ALL CONNECTED
Broadband Connection(Coax)...CABLE DISCONNECTED.
ONT feed into house is Coax.
My FiOS Service 20/5 After Free Speed Upgrade DOWN 30.83 Mbps UP 27.83 Mbps Latency 11 ms
Server NY NY 71.252.0.12
Tom
Freedom Essentials, QIP 7100 1,Bose SOLO TV Sound System,,QIP 7216 P2,M1424WR Rev F, iPad 2 WiFi,iPhone 5,TV SYST INFO Release 1.9.5 Build No. 17.45
Data Object 39.45
Similar Messages
-
I have a mac pro connected by ethernet to a cable modem via ethernet. There is only one ethernet port on the modem.
I want to keep the Mac connected via ethernet for speed. Is there a way that I can add an airport extreme to this set up - for my ipad and roku, and for guests to use - or do I need to buy a router to put between the modem and the mac?
If I need a router, what kind?
Thanks.The modem connects to the WAN "O" port on an AirPort Extreme router.
The Mac Pro connects to one of the three LAN <-> ports on the AirPort Extreme router.
Or if you do not need the ability to connect a hard drive to the USB port on the router, you can save a bit by using an AirPort Express.
The modem connects to the WAN "O" port, the Mac Pro connects to the LAN <-> port
Either the AirPort Extreme router or AirPort Express router will allow up to 50 wireless device to connect.
There are many other wireless modems offered by other manufacturers as well. -
Reg: How to submit out of two parameter either one should mandatory.
Hallo All,
I have a requirement in concurrent program parameter submit following conditions.
scenario:
1. I have two parameters in which atleast either one should always pass. for this case concurrent parameter should allow to submit the pgm.
2. If I missed out two marameters, Program should not allow to submit, there should pop-up message, "Please select item name or creation date parameter"
Thanks in advance.
Please guide me how to achive this scnario?
Thanks,
Velu.
Edited by: user10348287 on Mar 12, 2012 2:53 AMHi Anthony,
Try to connect the table with the "save FM". This FM should only execute, if it contains a text (via formula). After saving it should call the FM for displaying the selected record of the table. For initializing you can call the FM for displaying directly (use a guard condition).
Best Regards,
Marcel -
Generally when creating a Word file from either a Mac or Win7 pc and opening it on two different machines (either one first) it always prompts that the file is open and will be opened as read only.
However opening a CSS file does not prompt that it is already open on or from any machine which is causing code edits to be lost.
What we found from out testing:
- The file can be saved from one user to the server and WILL NOT PROMPT on other machines until the saving machine has the Dreamweaver program closed completely
- The file can be closed and Dreamweaver minimised to the launch bar but it still will not register on other machines that it has been changed.
- Also, until the Dreamweaver program is closed on the machines, it will continue to open it's saved version of the file.
Example Scenario:
- User 1 opens test.css (which is 2000 lines) and adds some code to the end of the file to bring it up to 2500 lines
- Meanwhile User 2 opens test.css as well (opens as 2000 lines as User 1’s edits have not yet been saved) and adds in code to bring it to 2300 lines
- User 1 saves his file and closes it - but Dreamweaver is still open.
- User 2 also saves his file and leaves Dreamweaver open.
- The server will report the size and last edit of the file the same as User 2 as he was the last person to save it (and if you open from the Win7 Machine it will show as User 2’s 2300 line version)
- If User 1 then open's the file again (from either the 'recent' in Dreamweaver OR clicking on the file directly in Finder...which version opens.... The version that User 1 saved! Not the true version on the server, but the version that User 1 edited and saved with 2500 lines in it.
- Same for User 2, he will open 'his' version with 2300 lines in.
Other information:
- Files are opened directly from the server
- Sometimes the users will save incrementally and re-open
- Most of the time users will save incrementally and keep the files open
- The users will never not save incrementally and just save when closing the file once finished
- The users are usually working on the files all day
- It is always the bottom lines of code that are lost. It could be a case of the two versions being mixed up and cutting off the newly added lines based on the line count (possibly).
It is as if Dreamweaver is holding a cache of the version locally and then only properly looking back to the server when it has been completely closed. It is very difficult to see how the server is causing such an impact on these files, there are very few logs which are giving any indication to the root cause of the problems.
Anyone know if this is a known issue?
Is there a way that there can be a featured implemented on the server that doesn't allow another user to open a file if it is already open on another machine?
ThanksYour server file handling has nothing, and really nothing to do with Adobe software. If files don't get locked for (over-)writing and/or lose connection to the program opening them, then your server is misconfigured. It's as plain and simple and that. Anything from "known file types"/ file associations not being set correctly, MIME types being botched, crooked user privileges and file permissions, missing Mac server extensions, delayed file writing on the server, generic network timeout issues and what have you. Either way, you have written a longwinded post with no real value since you haven't bothered to provide any proper technical info, most notably about the alleged server. Either way, the only way you can "fix" it is by straightening out your server and network configuration, not some magic switch in Adobe's software.
Mylenium -
Question about ethernet over coax?
I was wondering if anyone has any advice.
Here is my setup, I have
1) MI424WR router installed at one location. I have an ethernet switch connected to the router to carry ethernet all over the house. The MI424WR is connected to fios with a coax cable.
2) I have a coax cable ( connected to the fios) at a location where I cannot get an ethernet cable and where I have a computer that I would like to connect to the network. . I was wondering if I can connect something to that coax cable that would connect it to the network and allow me to connect the computer at that spot?
Thanks in advance
Joe
{edited for privacy}below are some ways for you to do what you would like to do. just keep in mind that those are advanced set ups and not supported over the phone or by technician at verizon, so you can do them at your own risk type of thing, and the only support you'll really have is from online users. . If your a DIY (Do it yourself) kinda guy, then these should work,
http://www.dslreports.com/faq/verizonfios/3.0_Networking
Speficially look at Can I get an ethernet connection in a room with only coax? -
Can I transfer data from my G4 to my IMac over a firewire without them syncing or messing either one up - do not want to modify either one...!
Boot the G4 Mac into Target mode...
http://support.apple.com/kb/HT1661
That should make the G4 look like a big FW drive to the iMac. -
Sharing one ethernet cable with two macs using a USB Ethernet Adaptor
I have two computers running Mac OS 10.6 but only one ethernet cable in my office. One ethernet cable goes from the wall to Mac #1. I have a cisco USB Ethernet Adaptor USB300M that I like to use as OUTGOING ethernet cable from Mac #1 to plug into Mac #2. Does anybody know how this works? Simply plugging it in does not work. Thanks for any suggestions!
If either of these computers is a Mac Pro (65 lb.) tower, all of which have two Ethernet jacks, Internet sharing is crisply supported with any additional Hardware. Cable the wall jack Ethernet to the first Ethernet port, then cable the second Ethernet port to the second Mac. Configuration is described in this article:
Mac OS X 10.6 Help: Sharing your Internet connection -
How do I manage Lightroom photos when using 2 computers, keeping all edits made on either one?
Based on http://forums.adobe.com/thread/1308132?tstart=0 I decided to add each question seperately:
Hello, I'm quite interested in buying Lightroom 5.2. I tried the RC which ran out now. Yet, I have a several questions that I can't really find good conclusive answers to, that I'd like to get answered before buying LR. Please don't write maybe like this or that (assumptions), since I don't want to start my whole workflow and then realize that I have to change everything around, so please answer, if you know for sure that something works and you are, preferably, using that method too.
This is the biggest question, where I mainly want a conclusive answer: How do I manage Lightroom photos when using 2 computers, keeping all edits made on either one of them, using the same photos for editing. I won't use DNG. Details: I mainly use my older MacBook Pro, but would like to be able to use my PC as it's way better (Specs: i5 2500K, 16GB RAM, SSD, USB3, nVidia GTX 560 TI etc.). I have 2 external HDs that I could use, one for Backup and one for the actual Photos/Edits. I'll probably need to use it as my internal HDs are quite full, and I can't just delete stuff or move it to an (Developer programs, Lossless music, etc.).
Based on this, how do I back up the whole thing e.g. Photos folder (all photos and edits, and preferably presets too)?I believe it should be possible to work cross-platform without having to relink files each time, or without having to keep exporting/importing the catalog, by keeping the single catalog and the image library on the one external drive which is then switched between systems as needed.
Obvious first requirement is an external drive that is formatted in such a way (e.g FAT32) that it can be used on both platforms in read/write mode. Given that, if the catalog AND the images parent folder are both established at the same level in one overall parent folder, then it should be possible to take advatage of Lightroom's ability to use relative paths rather than absolute paths to detect the images, no matter if the drive is named (Mac) or lettered (PC). This is how "export as Catalog" works, i.e. it creates a "package", aka a parent folder, containing the catalog and a replica of the exported images folder hierarchy alongside the catalog. Take that "package" to another system (same OS or not) and "it just works" even if the drive letter is different or the OS is different....because the relative path from catalog to images is still the same.
I haven't tested this cross-platform (though I have between different PC systems with different drive letters) so for me it's still just a theory, but there may be others who have done this successfully. -
Show the company I work for that we should have one cluster
The company I work for have several projects where we are going to use RAC. The issue I'm having is they want each database to be in its own cluster hardware. I'm trying to show then that we should cluster all the hardware together and make small RAC database in the one cluster.
Does any know of anyone that has written a go doc how why you should have one cluster versus multiple clusters.
Example of what they are thinking of doing note this is all separate hardware cluster1 will not be cluster with cluster2 I'm try to show them if we cluster it all together we get more power and may not need so much hardware:
Project 1
cluster1_dev
2 nodes
cluster2_qa
4 nodes
cluster3_prd
4 nodes
Project 2
cluster2_dev
2 nodes
cluster2_qa
4 nodes
cluster2_prd
4 nodes
What I’m proposing is the following setup:
Cluster_dev
3 nodes
Project1 instance cluster on all 3 nodes
Project2 instance cluster on all 3 nodes
Cluster_qa
6 nodes
Project1 instance cluster on all 6 nodes
Project2 instance cluster on all 6 nodes
Cluster_prd
6 nodes
Project1 instance cluster on all 6 nodes
Project2 instance cluster on all 6 nodesI am always impressed by choosing rac without having expressed what types of failures to be covered.
maybe you really don't need rac ...
moreover, rac is imho really not 2 nodes oriented but well grid oriented.
a lot of small server in the same cluster is for me the way to go or the the way to think.
Services features were introduced to allow one rac db to be shared by multiple applications. -
Using more than one Ethernet port
So I just brought myself another pair of TP link wifi adapters as I already had some, but the ones I had only had 1 port and these have 3. So I set it all up and try to use 2 ethernet ports as I want to use my xbox one and Laptop through these adapters. So when i set it up and pluged the ethernet cables into the router the broadband light on the hub goes orange and the broadband is lost unitl i take out one of the ethernet cables and reset the hub it works fine with just one.
I just really want to know why i cant have more than one ethernet cable plugged into the hub.
Solved!
Go to Solution.You can only connect one broadband extender to the home hub. This must be designated as the Access Point. All the rest need to be slaved to that Access Point. These need to be individually "paired" to the AP one connected to the home hub.
You can still use the other ports on the home hub for direct Ethernet connections.
If you try and connect more than one extender to a home hub Ethernet port, you will create a loopback, which will crash the home hub.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones. -
I have a coax cable running from the front house to the back house and want to connect my router to the iMac back there that serves up music and movies etc to the rest of the house. It's currently connected via wifi, but there are dropouts etc.
I've been pointed to a few different devices that can run ethernet over coax, such as this one:
http://www.netsys-direct.com/proddet...NH-310C&cat=27
there are a variety of them, and they all seem to say they have speeds in the 100mps to at the most 500 mps. My questions is this. How fast are current Airport and Ethernet speeds? I know they speak of Gigabit wireless, so does that mean 1000mps and up?
If I'm currently using wireless in this case, do you think switching to coax would slow things down a lot, or would it work ok?
thanks!802.11g aka "wireless-g" has a maximum theoretical speed of 54 megabits/second.
802.11n "wireless-n", has a maximum theoretical speed of 300 megabits/second, but to attain that it requires near-perfect conditions. It's normal to observe less than half that in actual use.
These vary according to many environmental phenomena that influence radio propagation. Observed speeds tend to be considerably less. "Gigabit Ethernet" isn't so influenced, but may also be less than 1000 Mb/s due to other network factors. -
Tcpip.sys related BSOD in Vista at either wifi/ ethernet network connection with my university
Dear all,
laptop:: Lenovo X61s 3G L7700
OS version: windows Vista business Sp1
tcpip.sys version: 6.0.6001.22167
wifi: Intel 4965AGN. Standard Gigabyte intel ethernet 82566MM
system drivers and BIOS are the most updated driver.
At my 2 homes using ADSL routers, there are absolutely no problems with network connection by wifi or ethernet. However, blue screen occurs when I bring this laptop to university and connect to the network via either ethernet or wifi. This happened to me a few months back. It crashed EVERY TIME when a network connection was attempted. It did not matter whether I updated my drivers on both wifi or ethernet cards. Whenever I bring it to either of my2 homes, no blue screen ever occurs.
It also happens when I attempt to connect to free wifi network in the airport. It crashes again with EXACTLY the same problem. I have to admit that I do not even where to start looking for the problems. System restore did not solve this either. I ran the WinBug analysis. It pointed towards tcpip.sys. My sys ver is at the top of this message.
Would appreciate if someone can point this to the right direction. I am seriously thinking of downgrading this to XP, since it had NEVER happened to XP.
thanks,
VIncent
WinBug analysis:
Microsoft (R) Windows Debugger Version 6.9.0003.113 X86
Copyright (c) Microsoft Corporation. All rights reserved.
Loading Dump File [C:\Users\vincentyip\Desktop\Mini011709-09.dmp]
Mini Kernel Dump File: Only registers and stack trace are available
Symbol search path is: SRV*c:\symbols*http://msdl.microsoft.com/download/symbols
Executable search path is:
Windows Server 2008 Kernel Version 6001 (Service Pack 1) MP (2 procs) Free x86 compatible
Product: WinNt, suite: TerminalServer SingleUserTS
Built by: 6001.18145.x86fre.vistasp1_gdr.080917-1612
Kernel base = 0x8200b000 PsLoadedModuleList = 0x82122c70
Debug session time: Sat Jan 17 21:04:50.693 2009 (GMT+0)
System Uptime: 0 days 0:08:18.357
Loading Kernel Symbols
Loading User Symbols
Loading unloaded module list
* Bugcheck Analysis *
Use !analyze -v to get detailed debugging information.
BugCheck 1000007F, {8, 803d3130, 0, 0}
Unable to load image dne2000.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for dne2000.sys
*** ERROR: Module load completed but symbols could not be loaded for dne2000.sys
Unable to load image Epfwndis.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for Epfwndis.sys
*** ERROR: Module load completed but symbols could not be loaded for Epfwndis.sys
*** WARNING: Unable to verify timestamp for epfw.sys
*** ERROR: Module load completed but symbols could not be loaded for epfw.sys
Probably caused by : tcpip.sys ( tcpip!WfpAuditEventGeneral+1cb )
Followup: MachineOwner
1: kd> !analyze -v
* Bugcheck Analysis *
UNEXPECTED_KERNEL_MODE_TRAP_M (1000007f)
This means a trap occurred in kernel mode, and it's a trap of a kind
that the kernel isn't allowed to have/catch (bound trap) or that
is always instant death (double fault). The first number in the
bugcheck params is the number of the trap (8 = double fault, etc)
Consult an Intel x86 family manual to learn more about what these
traps are. Here is a *portion* of those codes:
If kv shows a taskGate
use .tss on the part before the colon, then kv.
Else if kv shows a trapframe
use .trap on that value
Else
.trap on the appropriate frame will show where the trap was taken
(on x86, this will be the ebp that goes with the procedure KiTrap)
Endif
kb will then show the corrected stack.
Arguments:
Arg1: 00000008, EXCEPTION_DOUBLE_FAULT
Arg2: 803d3130
Arg3: 00000000
Arg4: 00000000
Debugging Details:
BUGCHECK_STR: 0x7f_8
CUSTOMER_CRASH_COUNT: 9
DEFAULT_BUCKET_ID: COMMON_SYSTEM_FAULT
PROCESS_NAME: System
CURRENT_IRQL: 2
LAST_CONTROL_TRANSFER: from 8a67c8da to 8203f6c0
STACK_TEXT:
8cf21274 8a67c8da 00000000 8cf21534 00000000 nt!SeReportSecurityEventWithSubCategory+0xe
8cf2154c 8a67cb3f 00003900 8cf216dc 8a67696d tcpip!WfpAuditEventGeneral+0x1cb
8cf21558 8a67696d 8cf21588 00000000 8cf21848 tcpip!KfdAuditEvent+0x38
8cf216dc 8a676709 0000001c 8cf219e0 8cf21848 tcpip!IndicateDropAudit+0x1ac
8cf217e0 8a67cddb 0000001c 0000001d 8cf219e0 tcpip!ShimIndicateDiscard+0x3e
8cf2181c 8a63025b 0000001c 8cf219e0 8cf21848 tcpip!ShimIndicateDiscardGeneral+0x50
8cf219f0 8a696833 00000011 00008900 00008900 tcpip!WfpInspectReceiveControlShimV4+0x2fb
8cf21a80 8a679a9f 00000002 86a52dc0 869ca000 tcpip!ProcessIcmpErrorClassify+0x1cf
8cf21d0c 8a67cf6f 00000001 00000002 00000000 tcpip!WfpProcessInTransportStackIndication+0xe1
8cf21d60 8a618e27 86a52dc0 00000002 00000001 tcpip!InetInspectReceiveDatagram+0xce
8cf21d94 8a618c2e 869d2668 b6aad4c8 a8396220 tcpip!RawBeginMessageIndication+0x35
8cf21de8 8a67657e 869d2668 00000002 00000000 tcpip!RawDeliverDatagrams+0xf9
8cf21e28 8a676105 869d2668 00000000 8cf21e64 tcpip!RawReceiveDatagrams+0x10d
8cf21e38 8a67402b 8cf21e4c c000023e 00000000 tcpip!RawNlClientReceiveDatagrams+0x12
8cf21e64 8a673dee 8a6cd19c 8cf21ec0 c000023e tcpip!IppDeliverListToProtocol+0x49
8cf21e84 8a673d34 8a6cac68 00000101 8cf21ec0 tcpip!IppProcessDeliverList+0x2a
8cf21edc 8a6734ec 8a6cac68 00000001 00000000 tcpip!IppReceiveHeaderBatch+0x20a
8cf21f6c 8a671fe6 879b6c90 00000000 820ee401 tcpip!IpFlcReceivePackets+0xbe1
8cf21fe8 8a67252e 89dfbbe8 89d16bf0 00000000 tcpip!FlpReceiveNonPreValidatedNetBufferListChain+0x6e3
8cf22010 8a5400b0 89dfbbe8 89d16bf0 00000000 tcpip!FlReceiveNetBufferListChain+0x104
8cf22044 8a532919 00dfb830 89d16bf0 00000000 ndis!ndisMIndicateNetBufferListsToOpen+0xab
8cf2206c 8a532890 00000000 00000001 87c840e8 ndis!ndisIndicateSortedNetBufferLists+0x4a
8cf221e8 8a47357f 87c840e8 00000000 00000000 ndis!ndisMDispatchReceiveNetBufferLists+0x129
8cf22204 8a5452ba 87c840e8 89d16bf0 00000000 ndis!ndisMTopReceiveNetBufferLists+0x2c
8cf22250 8a53fba0 02c840e8 8cf22294 00000001 ndis!ndisMIndicatePacketsToNetBufferLists+0xe9
8cf2228c 8a565bfc 85756ef8 8796aa54 89dd87c4 ndis!ndisLWM5IndicateReceive+0x31d
8cf222b0 8df0e67a 879b6d10 8796aa54 89dd87c4 ndis!EthIndicateReceive+0x1f
WARNING: Stack unwind information not available. Following frames may be wrong.
8cf22334 8deffa73 89df7020 89dd8778 89dd87c4 dne2000+0x1767a
8cf22360 8a565570 89df7020 89dd8778 89dd87c4 dne2000+0x8a73
8cf223d0 8ebe5f49 c000009a 8cf22400 00000001 ndis!ethFilterDprIndicateReceivePacket+0x2fc
8cf223f8 8ebe6f3b 89dd8778 00000000 87c99008 Epfwndis+0x2f49
8cf2243c 8ebe49cb 830020cc 89b582d8 00000008 Epfwndis+0x3f3b
8cf22488 8a5487fe 87bc3b80 87434d60 87bc3c38 Epfwndis+0x19cb
8cf224a4 8a548938 87bc3b80 87434d60 00000000 ndis!ndisDummyIrpHandler+0x72
8cf22594 820c6fd3 87bc3b80 87434d60 875ac9a8 ndis!ndisDeviceControlIrpHandler+0xe4
8cf225ac 8fd91011 89b0cbdc 875ac9a8 00000000 nt!IofCallDriver+0x63
8cf225d4 8fd91148 875ac9a8 875acffe 89b582d8 epfw+0x7011
8cf225ec 8fd8b1cb 89b0cbdc 8fd99924 830020cc epfw+0x7148
8cf2262c 8fd91bf3 89b0cb18 89b582d8 84e99264 epfw+0x11cb
8cf22640 8fd946a7 89b0cb18 89b582d8 84e99264 epfw+0x7bf3
8cf2268c 8a5a980a 86992548 00000089 876cf3d8 epfw+0xa6a7
8cf227f8 89b9af4e 0000044c 89b0cb18 89b582d8 NETIO!PopulateContext+0x2f
8cf228d0 8a5aa7a4 00000000 89b1bb6d 00002711 0x89b9af4e
8cf22964 8a5ae5ed 8a5d3324 8cf229e4 00000000 NETIO!MatchCondition+0x4b
8cf229ac 823cb5b0 876cf3b8 84916500 00000000 NETIO!KfdAleAcquireEndpointContextFromFlow+0x82
8cf229bc 8cf22a18 876cf3f8 8cf229e8 8a5ae3f7 hal!KfLowerIrql+0x64
00000000 00000000 00000000 00000000 00000000 0x8cf22a18
STACK_COMMAND: kb
FOLLOWUP_IP:
tcpip!WfpAuditEventGeneral+1cb
8a67c8da 5b pop ebx
SYMBOL_STACK_INDEX: 1
SYMBOL_NAME: tcpip!WfpAuditEventGeneral+1cb
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: tcpip
IMAGE_NAME: tcpip.sys
DEBUG_FLR_IMAGE_TIMESTAMP: 4812c4ce
FAILURE_BUCKET_ID: 0x7f_8_tcpip!WfpAuditEventGeneral+1cb
BUCKET_ID: 0x7f_8_tcpip!WfpAuditEventGeneral+1cb
Followup: MachineOwnerPer my original post:
"When my ATV is connected via ethernet, and I attempt to play some internet radio stations, some will work just fine while others won't. For example, when connected to my home network via ethernet, some internet radio channels (I can't give a percentage because I haven't tested all of them) will play just fine, however, others won't. The ATV will attempt to connect, but the spinning progress bar just goes and goes and goes until it eventually errors out (no error number is provided, it just says that there was trouble loading the content). The funny thing (or not so funny thing actually) is that if I unplug the ethernet cable, and connect my ATV to the network via wifi, those same stations that didn't play when ATV was connected via ethernet, WILL play when ATV is connected via wifi. So, in short, some stations play just fine when ATV is connected to home network, through wireless router, via either wifi OR ethernet, yet some will only play when ATV is connected to home network via wifi. I have found this to be the same when it comes to downloading or refreshing the photos in my photo stream. If I throw new photos in my photo stream on iCloud, and the ATV is connected via ethernet, they won't refresh to the ATV, however, if I unplug the ATV and connect via wifi they begin to refresh."
There are dozens of original threads out there that report of similar - if not exact, issues. I have contacted "Roy" per his request and not heard back from him (if such a person exists). I have "restored" my ATV and rebooted all equipment to no avail. Until Apple gets with it, acknowledges their problem, and fixes it, I am resigned to just having to deal with switching back and forth from wifi to ethernet, and so on. -
I have a G5 and iBook with PowerPC/iTunes 10....just recently I can't bring up the preset Internet radio on either one. Is this a glitch, or have they been permanently disabled for older versions of iTunes?
I should have posted this for you a while ago. My apologies for not doing it sooner. This was passed on to me by another user R C-R
He deserves the credit for this workaround. This is his post from an area in the forum where you have to be level 6 or higher in which to participate.
I am getting the same (global) error using iTunes 10.3.1 on a 2008 MacBook running 10.6.8.
A really, really awkward workaround that works for me (for now) is if you have the URL of the Internet radio server you can go to Advanced > Open Stream... (in iTunes 10.x) or type command + U, enter it there & click OK. The station should play fine in 10.x.
You can get the URL from any version of iTunes that still supports the "radio tuning service" (which I gather is an Apple server thing Apple is no longer supporting for 10.x). Play the station normally from the newer version & type command + I to open the info window. At the bottom of the "Summary" tab you will see the URL. (Annoyingly, you can't copy the text so you will have to write it down.)
Once you have that, you can play the station in 10.x & add it to a playlist for future use.
To check this out, maybe try http://198.27.80.37/stream/mbarsott.pls -- it is a European Jazz station that works fine for me with iTunes 10.3.1.
This workaround does work, but is a bit cumbersome. I'm still holding out hope that it is just a glitch. -
I want a macbook,i really do. But its getting closer and closer to the time that im planning on buying one, and im not sure if i should get one yet. Im a sophmore in highschool, and i need a computer for highschool. I know im going to end up getting some bias answers but--Should i get a macbook now, or should i get some other computer? The computer that im going to get is going to have to last from now till--hopefully--the end of collage. So is there another computer that i should get, and get a mac sometime in the future? maybe even before collage and just have some cheap thing for highschool. I just want your opinions, im not trying to starts some kind of mac v. not mac arguement. I just didnt know where a good place to ask would be so i decided to ask here. Thanks Alot.
I used both Mac and PCs during college.
As a recent graduate, it was very important that I paid attention to my major and class requirements. Several classes I had required Internet Explorer, MS Project, and Visio.
At the time the best choice for me was a PC. However, as a owner of a MacBook, I now dual boot and have the best of both worlds. However, dual booting does require a Windows XP Pro "SP2" disc.
*Getting Windows XP*
Around college you should not have a problem getting this. A single XP license actually allows you to install the OS on (1) PC and (1) Notebook. Finding another copy shouldn't be that difficult. And if worse comes to worse, you just call Microsoft (some place in India) and activate the copy over the phone. Just tell them the copy is on one PC to make it a quick phone call, they can't understand much more let alone any explanation of the license and if it was uninstalled off another computer.
*Word Processor*
I use Word 2004 for Mac. It functions well, but I feel Word 2003 is still better.
*School Software*
I would also check with your school and see what software you get with your tuition. Some schools just give out AntiVirus crap, others provide entire Office Suites. So if you are going for broke, keeping software cost in your plan is a good idea.
*Final Opinion*
If it were me, I would go with the MacBook. Because I know how to hunt for software, I don't figure it paying for any. The MacBook is actually a very competitive price. Since Apple provides the option to run Windows, why not get a MacBook to take advantage of both OS X and Windows environments. -
Removing cookies does not work, either one at a time, or remove all. I tried from history and from the options screen. They appear to go away but when I go back in they are all back again. This is happening in the latest version that was automatically updated.'''bold text'''
Do you have an extension like TACO (Abine) or TrackerBlock that maintains a set of OPT-OUT cookies?
* Targeted Advertising Cookie Opt-Out (TACO): https://addons.mozilla.org/firefox/addon/targeted-advertising-cookie-op/
* TrackerBlock: https://addons.mozilla.org/firefox/addon/trackerblock/
* Beef Taco (Targeted Advertising Cookie Opt-Out): https://addons.mozilla.org/firefox/addon/beef-taco-targeted-advertising/
In that case you need to remove such an extension to get rid of those cookies.
Maybe you are looking for
-
Safari doesn't open.....(Must be On Safari..)
Ok, this Safari is useless! It has crashed my OSX 10.4, resorting me to re-install/archive my entire system. I'm now at 10.3 and it seems ok. Anyways, back to Safari...Now it does the bouncing ball of death dance and goes nowhere fast. I think it has
-
Mail's Monoco 9 rendering help in 10.9, sigh
Hey everyone! Someone here probably knows the quick answer to this question, but it's not something that the average users knows off the top of their head. When I updated to 10.9, Mail no longer renders my font setting of Monaco 9 properly in messag
-
I have Norton 360 on my computer. I use Firefox regularly and I downloaded the latest version of Firefox. I was able to use Norton 360 in Firefox. Norton saved all my passwords I use online. Now the latest update of Firefox does not allow me to use N
-
FB4 Beta2 does not include swz files
When compiling a release Build, FB4 does not include the smaller swz files but bigger swf files (e. g. framework_4.0.0.10945.swf) instead. The swz files where included only a few time at the beginning of the project. I need to finish this project wit
-
White stripes suddenlt appeared at the bottom of the screen on my ipod nano a few weeks ago. I figured it was just from use and that it is an older model- I could still see through them and use the device. Yesterday, only the left half of the scree